Counting matching models…
I create this alternative pedal plates for DC Simracing DC-3 pedals, bigger and softer than the original ones, giving the posibility to use it without shoes. I printed it on PLA but i'm sure that PETG it's better for this use. With PLA I…
After upgrading my SR-P Lite pedals with a load cell I wasn't happy with how they felt with their smooth plates and shallow angle. I found some decent looking and priced pedals on Amazon and created adapters for mounting them in a more…
So I needed a storage solution for my kayak pedal drive. It is a knock off chineese hobie mirage flap pedal drive. I have Gladiator geartrack slat wall. I designed a storage rack for it. I still havent found a print orientation I like. I…
I could not find a good free model for the SIMJACK Ultimate (UT) brake pedal, so I made one. It does not use the plate that comes with the motor. Print circular side on the plate, support on build plate only. Use Loctite for pedal plate…
This is a mod for use with PXN PDHM, with this mod you can have a load cell in your brake pedal. It is totally plug and play, you don't need to change the original electronics. It uses a inexpensive 50kg load cell a HX711 and a arduino…
After rescrewing the rod on the SRP brake for the thousandth time, I finally stripped the thread with some excessive force. Here's a replacement I quickly modelled up. Before you're worried, all the braking force will be handled by the…
The pedal holder is made from scratch and we used an inner tube to prevent it from scratching the frame and in order for it to fit as tightly as it did. Due to the magnet at the bootom the pedal won't fall out, was an old magnet we still…
Got my self the new Neo HPR by simagic for my rig and couldn't find any adapters for them so I made my own. This adapter works for Throttle and Clutch only. I have an original P-HPR haptic reactor on my brake and I had found already an…
This should be functionally the same as TL-PD400 tool. Outer sleeve tightens the 10 mm nut and inner tightens the 7 mm one. I have the PD-GR400. Haven't tested with others, but I'm guessing they use the same nuts. You put the smaller tool…
Modelled entirely myself, but mostly a direct copy in terms of dimensions. Throttle fills the entire pedal face now. I'm surprised how much grip the pattern gives. Made with a maximum of 30deg overhangs for better print quality. No extra…
I am continuing to try out different platform/flat mountain bike pedals that can accept toe clips (with or without modifications or adapters). The K-PEDC mountain/BMX pedals look like they might work out. Of course, they do need adapter…
Standard 370 motor has a length of 30.5mm a diameter of 24mm. Printed in PLA with whatever default settings. The motor is held with zip ties to the mount. That ensures that there is no play. The mount is attached to the pedal with 2 M3…
Remove the slop from your clutch pedal clevis with this bushing. I recommend printing with TPU or ABS for the best fit
General: A replacement pedal for small electric scooter Why I designed this: I designed this to replace the rubber pedal that my son managed to lose Printing notes: Layer height: .15 Recommended Material: TPU Supports: Painted organic…
MATERIALS: 1 x M4 x 45 bolt and nut. 2 x M4 washer 1 x Square cut of “skateboard tape” & a little super glue. SETTINGS: PLA - Print in current orientation (pic rail flat on bed), 50-75% infill, 4 wall lines, tree/normal support 40 degree…
Virpil Ace Flight Pedals Backstop to adjust pedal resting position. Various size stops to raise the pedal resting position to make it more comfortable and scale the axis down. Assembly -Remove original rubber rear stops -Printed should…
just print it ;-) Add an additional Design with only 15 degree elevation.
This is an improved pedal frame for the most usual type of pedals. It is wider and it has much better grip! They have as much grip as big platforms. It makes pedaling more efficient and comfortable. You can also pimp your ride printing…
After summer, I found a few old bike pedals in the my toolbox. Not good for biking, but the body is still strong, anti-slip, ready to carry some weight. With a quick clean, they shine again and hold gear reliably. Included files: Default…
****************** Long Shaft Servo Discontinued ****************** The long shaft servo was discontinued :(. I removed the alpha 0.1 printable mount for the short shaft motor as it didn't work. I'm working on a new mount that shifts the…
Mod for Logitech G29 , G27 , G25 , or Driving Force GT pedals by replacing the stock potentiometers with Hall effect sensors for smoother, more precise input and zero wear over time. This printable bracket makes the conversion simple and…
I designed a replacement pedal for my kiddos tricycle. It made a nice training for Fusion 360. Print Settings Printer: Print Rite DIY Rafts: No Supports: Yes Resolution: 0.25 -0.35 Infill: 80% Notes: Printed in PLA but ABS would be a…
Recommended tape, the 3D printed knurling is hard to clean: https://aliexpress.com/item/1005009201004263.html Hardware required: Clamp Version: 4pcs. M3x20 4pcs. M3 nut Standalone Version: 2pcs M8x150 2pcs M8 Nut You'll lose the ability…
Bracket / Holder for simagic board pedals P2000 or Haptic for alliminium profile. Assembly: Remove the back plate from the board and attach it to the printed part. Use the same screws as before. Easy to install. M5 screws for alliminium…
I purchased a used Mission Engineering expression pedal for my Helix, but it came with ony 2 of the rubber bumper/feet missing. Instead of buying replacements, I decided to create and print better bumpers from TPU rubber, as 2 bars…
pedale pour poubelle de salle de bains Print Settings Rafts: No Supports: Yes Filament Material: TPU Notes: TPU95 Category: Bathroom
use flat countersunk head M6*30mm x2 To attach the case to the pedal and hex socket head cap screw M5*30mm x2 To pcb
🚀 Support My Work🚀 If you enjoy my designs, you can help me keep the creative spark alive: Post a Make: Seeing your prints is the best reward! It also helps me earn Prusameters to keep the filament flowing. 💎 Like & Download: Your…
Pedalboard pro kytarové efekty, rozšířitelný. Expandable pedalboard for guitar effects.
What can you expect in Detail? A variable width game controller from 50cm to 60cm adjustable. Nudge/Tilt with accelerometer gyroscope, adjustable on the screen. Variable Flipper Buttons position, for ergonomic handling. Touchscreen Menu…
I used two M4/M5 Screws and self-locking nuts to attach the swing bar, as well as two M4/M5 Screws and bolts to secure the pedal. The AliExpress spring bolt is an M6 top and bottom. Depending on which file folder you want to use, two…
NOTE - they work! Better than I expected. Need frame protection from pedals for sliding bike rail storage system? Try out these bellows style slip on protectors. I designed them to fit TMACs, but they can expand or fit smaller pedals with…
This is a remix of the V5.8 accelerator pedal by Lebois to make a clutch with an adjustable regressive (over-cam) feel to allow an adjustable bite point. The base is the hall sensor version from one of my other remixes and this one has a…
Mazda MX-5 NA/NB Clutch & Brake Pedal Rubber Cover This download includes a 3D-printable model of the clutch and brake pedal rubber cover for the Mazda MX-5 Miata NA/NB (1989–2005). The model was designed based on OEM pedal covers to…
I wanted to print the pedal in a 45° angle so that the stress isn’t aligned straight across layer bonds, which usually makes the parts a bit stronger. However, printing larger parts like the cover and base of the pedal with the built-in…
Simple elastomer mod for cammus cp5 pedals. Damper mount PETG: 0.24 height Damper TPU (worked best for me, if u find better options let me know): 5 walls 5 bottom layers 5 top layers 50% gyroid infill Assembly: Quite hard to push it in, i…
I made this overengineered pedalboard for my cheap china pedals, But it does look clean :) The pedals can be found on aliexpress and temu and sound suprisingly good for the price.. I got this whole setup (pedals, cabels, powersupply and…
This 80x80 mm flat platform can be mounted on Speedplay legacy clipless pedals without any tools. The sliding tray locks the spiked top to the Speedplay lollypop. This pedal platform is intended for short rides only. The release knob…
This is a printable Stabilizer leg with optional Foot Rest or "Dead Pedal" that can be a great place to rest you feet if you don't have a clutch pedal or a mount for the pedals. No supports should be needed! The stabilizer can be…
I'm very new to 3d printing and modeling in general. This was the first model that I made in Fusion. I took inspiration from aottesen's design for the Logitech G920 Pedal Wall Mount, but completely designed this myself. It appears to be a…
Changed the size to 35.6mm by 92.5mm, same thickness and repaired the original STL with Prusa and Windows algorythms. Because the steel backplate offers shielding and PETG or PLA does not, I added Conductive foil HVAC tape to the inside…
Increased size quite a bit. It it tight on the back with the rubber and the screws pull it in. Start the 4 corner screws loosely, then tighten progressively. Print in PETG or PLA (if it will not be exposed to high heat like in a vehicle…
My trash can lid lifter that was actuated by a foot pedal was broken by my 10 year old. CA glue and two-part epoxy couldn't fix the broken actuation piece, so I made my own. Printed in PETG because I guess it needed strength to not break…
Template for DIY guitar pedal assembly in 1590B enclosure. Designed to ensure correct potentiometer and switch placement and simplify soldering outside the enclosure. 3x3 grid of 8mm holes, dX = 18mm, dY = 12mm (see attachment).…
Inmotion V11 pedals dumper replacement. Print using TPU, 100% infill
2x2 Gridfinity guitar pedal holder. Has a trough in the middle for the little nub on Boss pedals. Currently using it to hold a DS-1, TU-2, and DD-3. There's wiggle room inside so it should hold some larger pedals as well. It fits (barely)…
Remix of popular fidget made for Heat board game Printing: PETG 3 walls, 4 top and bottom layers, 15% infill Be careful with the main part, spring can be damaged if you force it of the plate when it's done For main part, do a colour…
I needed a holder for the electronics compartment of my simmson pedal set. As the wires are very short it had to be on the end of the pedal holder. The 2 parts are holt together with 4 M3 screws and nuts. Some holes included, also added…
Load cell pedal back washer 5mm. Remove the original washer; the center hole is slightly tight, making it easy to attach the small plastic slider. This ensures it doesn't move too much and fall during installation.
quick file to mimic stompshield, protects potentiometer heads from moving around when stored in bags or handled in transport and such (a.k.a. saves your analog pedal settings) of course quite girthy in comparison to the original…
A slight remix of the original model, editing the power station holder and the sides pieces.
Speedometer for pedal car or another toy. Designed to fasten to car with a zip tie.
WARNING: This will move your accelerator pedal much closer to your brake pedal than stock. Install at your own risk. Pedal spacer for moving the accelerator pedal back 25mm and closer to the brake pedal 15mm-20mm for easier heel-toe. I…
Pedal actuator for the Roland HD1 Lite e-kit. So the rubber actuator that it comes with dries out, and you can of course find replacement parts but I am hoping that TPU fares a little better. I tried different densities, 30%, 15%, as I…
This is an arduino box, designed to host 6 jack cables - as I needed to get the signals of switch pedals and get the info into puredata. I had some elegoo boards laying around - it fits perfectly - but it should fit an original UNO. I…
This is a remix of Christiano247's guitar pedal topper. https://www.printables.com/model/1182130-guitar-pedal-switch- This one was modified to fit onto a standard 8.5mm foot pedal switch, specifically for a Looptimus pedal, which used…
The Simagic P2000 Throttle Pedal Plate is designed to give you more precision and flexibility when fine-tuning your pedal setup. For installation, you will need M6 thread inserts (outer diameter approx. 7.8 mm, length 10 mm). These…
The Simagic P2000 Brake Pedal Plate is designed to give you more precision and flexibility when fine-tuning your pedal setup. For installation, you will need M6 thread inserts (outer diameter approx. 7.8 mm, length 10 mm). These inserts…
The original model blocks some pedal outputs (e.g., Loop Station or digital delay units) because they feature multiple output jacks.
I printed the Modular Pedal Board , the problem is that the volume or wah pedals are in angle and it is difficult to use them, mainly when you have to bring them up. So I disigned a riser that can be used for pedals that you want to use…
Just a simple guitar pedal box for when you buy a used pedal & they don't have a box to store it in.
Save the world from unnecessary waste. Extend the lifespan of your equipment. Do-It-Yourself repair of a Hammond B-200 expression pedal's Leslie switch that has a broken spring. Print it using 10 mm layer hight. The three images show how…
Cirrus calls out for a 7.375" x 2" block to support the rudder pedals during rigging and inspections of the rudder flight controls. Printed in PLA+ Walls: minimum of 2, add more walls if you want to print with a lower infill. Infill: 5-15%
Works with Fanatec CSL Pedals (should work for regular brake, LC brake, and accelerator) and the following 4Ohm 25W Vibration Speaker . Each mount requires (2) M4x0.7x20mm screws and (1) M5x0.8x25mm hex bolt (with an 8mm head width and…
Pedals for mini balance bike DELANIT Педаль на шатун беговела Деланит
Morgan 30L Stainless Steel Pedal Bin — Lid Hinge Replacement The plastic hinge cap on the Morgan 30L Stainless Steel Pedal Bin (Bunnings SKU p4520215, ~$28.95) is a known failure point. The original part becomes brittle over time and…
For attachment, I used some nonpermanent "Gorilla Contact Adhesive" so that any residue can be removed easily without marking the pedals and allowing for a small amount of flex within the join. As most of the weight is also supported with…
Lap tracker for Heat: Pedal to the Metal. Designed to use the cones from https://makerworld.com/en/models/1578417-mini-traffic-cones-and-flags-set-for-race-tracks#profileId-1660867 Include multicolor and mono color versions.
Sorry, this one in Russian: Демпфер педали газа для nissan almera classic b10, замена штатному. Меняется, если много ошибок по педали и/или обороты двигателя около 2000 и двигатель мало или никак не реагирует на нажатие педали.
These pedalboard legs aren't pretty (I might modify them later) but very functional and sturdy. I designed them based on my needs and a piece of wood board I had laying around. I like mixing materials when designing and building stuff,…
A high-quality, detailed 3D model of helicopter anti-torque pedals, designed with precision for flight simulation enthusiasts and cockpit builders.
A little on the large side, maybe, but it gives more room for prototyping. Feel free to remix and resize as needed. Holes are sized for 3x 6mm mini-pot control knobs, 1x 12mm stompbox bypass switch, 2x 11mm input/output jacks. Print with…
Printed in XYPOLYER ABS CF, recommend the most infill and perimeter as possible, mine is 40% infill and 5 perimeters
🚀 Support My Work🚀 If you enjoy my designs, you can help me keep the creative spark alive: Post a Make: Seeing your prints is the best reward! It also helps me earn Prusameters to keep the filament flowing. 💎 Like & Download: Your…
A small utility extension of Vioppoiv's modular system - I needed a half size unit to accommodate cables for a small board. Photo shows my 1 1/2 x 3 unit board for a HX stomp, Boss RC-10R and a batter powered unit.
STP model of a Type 01 Foot pedal switch for Bernina sewing machines. Use as basis of design for accessories.
A compact solution for fastening a Spedal CL871 touchscreen for Apple CarPlay / Android Auto to a common 22mm diameter bracket on my wife's Honda Transalp XL 750. What you need Please note: All links to Amazon ( amzn.to ), AliExpress (…
Radio Flyer Folding Trike Compatible Pedal & C-Clip
Adaptive pedal for Kinder King Kids Tricycle (Amazon link below) Designed for a tool-free perfect fit. Pedal and top bracket will need to be mirrored in slicer. Two adapters are required for each side. One adapter goes on upside down, one…
The clutch pedal started clicking which was caused by the plastic clip of the master cylinder rod popping out from the clutch pedal assembly. This print prevents the plastic clip from popping out. You will need two max 5mm wide zip ties…
This is a gas pedal for the TLR 7 Sub for a P365 X Macro. I remixed this model to better fit my pistol and the shooting. I extended to shelf so it better fits the frame of X Macro and also lowered the picatinny clamp so the light sits…
[Note that the photo used for this listing is from an earlier test/draft. The final posted here is better] Pedal for the Korg AX3000G. Probably works on other AX3000 or Korg models. Print on the side and use tree supports
I recommend printing these in a semi-flexible material, such as 95A TPU or SBS, but with 4+ walls and 25%+ infill. The extension is slid onto the pedal and then held in place by two cable ties. I have included two versions of every…
Quick model from dimensions in a picture. Untested, print and see if it fits.
This enclosure is designed to house the Logitech G29 mainboard and provide clean, protected access to the pedal and shifter connections. It offers a compact and organized solution for projects where the original wheel housing is not used,…
One of the originals fell out, so printed a couple PETG replacements. A bit more snug than the originals, so shouldn't fall out.
Custom-fit reflective inserts for Redshift Arclight Pro pedals, offering a low-maintenance, no-charge alternative that’s also less likely to be targeted by thieves. 🧰 Materials (per reflector) 2x neodymium magnets (Ø 8 mm × 3 mm, with…
Spacer to place Saitek Combat Rudder Pedals away from wall. Sets the pedals around 220 mm away from the wall. Very sturdy - except pins, but they are not really mechanically stressed. Complete with anti slip or felt pads on bottom and…
This Spacer (Remix) is for the rudderpedals from Saitek/Logitech to bridge gap between ur pedals and the wall. The Original Model from PDrill used printable plastic pieces for it, which took, if u had a long gap to bridge quite a lot of…
![[Remix] Moza SRP Pedal Faces](https://media.printables.com/media/prints/92352616-5f25-4128-8e0f-dedfb2d90535/images/9523628_1a83e115-11e8-4606-8d85-5759bb99e173_7bdb50b2-2bdb-4b06-bc61-a92ebaa29ace/20250417_181116.jpg)
