183 models
This remix allows the use of sensors I purchased off Amazon (HiLetgo) that had a different style of connector from the sensor the original case was designed for.
Print approx. €0.72–€0.89 excl. taxPreliminary estimate for one variant
print with PLA Model might warp, because it's so flat and wide/long, so corners might bend and detach from bed - destroying the print, so make sure you have cleaned bed and have good bed levelling. Holder is sticked to the glass wall with…
This case supports a Raspberry Pi Pico W with a DHT22 in separate internal compartments. The DHT22 side has vents on the side and top to allow for airflow to enter the housing. I am using this with MQTT to HomeAssistant. I have the…
Print approx. €1.13–€1.38 excl. taxPreliminary estimate for PETGSource material: PET
Design to fit DHT22 module assembly produced by DSD Tech. Module can be found on amazon. Similar product may work. Base mounts to surface with single fasteners. All other components compress fit. I mounted this DHT22 print to my MK3S+…
Print approx. €1.11–€1.36 excl. taxPreliminary estimate for PETGSource material: PET
Das Sensorgehäuse wurde speziell für den DHT22 Temperatur- und Luftfeuchtigkeitssensor entwickelt und optimiert. Mit seinem durchdachten, passgenauen Design schützt es den Sensor zuverlässig vor mechanischen Belastungen und ermöglicht…
Print approx. €0.69–€0.84 excl. taxPreliminary estimate for PETGSource material: PET
This is a simple case for a D1 Mini with a DHT22 Shield for the Mini from Berrybase The D1 Mini is squeezed into the holders on the None-Open side. This fits quite well and prints without support! The tree SVG used in the Design is from…
This model is a remix of the original models: Catch-All Trays / Desk organizer Catch-All Trays / Desk organizer - stackable remix Catch-All Trays / Desk organizer - lid variants remix It is fully compatible with this remixing models and…
Print approx. €0.57–€0.70 excl. taxPreliminary estimate for PETGSource material: PET
README: All stls are already in the correct print orientation. Motor: Any 29 series Samsung microwave blower- DE31-00029H, DE31-00029K, DE31-00029J, etc etc You can find these for decent prices on ebay. If you want to have the more common…
Originally published here: Motorola Moto G72 G82 & Edge (2022) xt2205 case by tato_713 - Thingiverse Some of the models are designed for rigid materials and others for flexible ones. The models materials are not interchangeable , so pay…
Two part case for your cheap slim DHT22 board. You can find the matching DHT22 / AM2302 board all over the internet. Just make sure it looks the same - there are many different form factors floating around. Requires 4x M2.5x6mm screws 3x…
This custom-designed enclosure is tailored to house the Plantower PMS5003 Air Quality Sensor, along with an ESP32 NodeMCU and a DHT22 (or BME280 when using the alternative lid included in the files) temperature and humidity sensor…
DHT22 sensor outdoor box. The box is designed to prevent water ingress, allow air flow, and mitigate overheating by the sun. It also has a chimney to avoid the problem of condensation. This piece is still under test. 4 m3 screws are…
Gehäuse für Wemos D1 mini oder andere ESP8266-Boards (Esp32, nodemcu ...) mit DHT22 / AM2302-Sensor. Case for Wemos D1 mini or other ESP8266 boards (Esp32, nodemcu ...) with DHT22/AM2302 Sensor. Print Settings Printer Brand: Creality…
This is my design for DHT22 sensor enclosure with 3pin JST-XH connector
What is this? This is an enclosure designed to house an ESP32 board (specifically, an ESP32 DevKit V1 board), a PMS5003 sensor, and a DHT22 temperature/humidity sensor. It's powered through the ESP32's micro USB port, which is exposed on…
I created a water meter sensor based on Lolin D1 mini v4 and induction probe LJ18A3-8Z/BX ( Build a cheap water usage sensor using ESPhome and a proximity sensor ). And I needed a box to house the D1 mini. Since it was already there, I…
Fixing the gap between the two components; now they fit tight together; Taking out the screw hole and replaced with a pin; New Air vents pattern This remix is used in my project here: https://www.thingiverse.com/thing:4352377 Enjoy!…
Case for dht22 on other sensor version outdoor with PG screw opening and cable stripe connector version indoor with backwall cable opening Used M2 8mm screws for lid M2x4x3,5 threaded inserts PG7 screw connection for outdoor version DHT22…
This little enclosure will hold an ESP32 and DHT22 snugly, for wifi climate monitoring in a nice small package. I recommend the vented, direct soldered lid. Even with the vents, if you use this without deep sleep or lower power mode, THE…
Republished from my thingiverse: https://www.thingiverse.com/thing:3342804 Links to the parts contain Banggood's affilate metadata. Intro I needed a PM2.5/PM10 sensor during this winter season. I wanted to monitor more than one room and…
Floor stand for tower orientation of 2U equipment. I designed this for my APC SMT2200RM2U. Should fit 2200 and 3000 models of APC UPSes (or “schneider electric”). May fit other 2U UPSes and equipment. Be careful not to block any…
A case for a humidity sensor system consisting of a DHT22 sensor, a Wemos D1 Mini, a 18650 battery holder and a battery charging module. Features: Sensor is thermally isolated from the rest of the electronics lid holds tight by press fit…
This is my first attemp for a sensor case, which reads temperature, humidity and lux. It uses a d1mini flashed with Tasmota and a DHT22 and BH1750 (GY-302) as sensors. The data is published via MQTT to my HomeAssistant instance. This is a…
Enspired by the DHT22 Feather Enclosure created by cnf I decided to create my own. This model will enclose the Wemos D1 mini and a DHT22 sensor.
This enclosure is designed for the Waveshare ESP32-S3 Ethernet Development Board with PoE, used in combination with a DHT22 temperature and humidity sensor connected via cable. It includes dedicated cutouts for: The RJ45 Ethernet port A…
Temperature sensor DHT22 case
Snap fit for the screen and rear cover, M2 screws for the ESP32 board. Supports needed. Left and right side cable routing options. DHT22 → GPIO4 SDA → GPIO21 SCL → GPIO22
This is a ventilated mounting bracket for a DHT22 Temperature+Humidity sensor, with an integrated connector that the DHT22 plugs into. It uses standard JST-XH 2.5mm crimp pins. You can find these at about any electronics supply house.…
Simple and small NodeMCU(ESP8266) and DHT22 case. 4x bolt m3x12mm The DHT22 is very close to the ESP. Create a code to put the ESP in “Sleep”. Then it will work fine!
Raspberry case for the sensor Category: Electronics
a small case for a ESP8266 D1 Mini with a DHT22 Shield Holes for wall mounting 4mm Dia
Dew Point Ventilation This is a case for another approach of dew point ventilation. Dew point ventilation means that you measure the temperature and humidity inside and outside. To decide whether ventilation is useful or not, you…
Outdoor Case for Temperature and Humidity Sensor I'm working on a ventilation system , that needs to know the humidity outside the basement. Therefore we need this case for a temperature and humidity sensor. This case is intended for the…
I bought Some Dell monitors and used them for some time. Eventually I got a mount, so I could have a 4 monitor setup. These didn't have VESA mounts, so I was looking at replacing all my monitors. I decided to model an adapter to fit on my…
Dear makers, we would like to share our ceiling case for DHT22 sensor, together with PIR Arduino compatible sensor HC-SR501. Use two 2x4mm screws for fixing PIR. Drill hole 67 mm. We tested with PETG due to higher temperature resistance…
This is a box for the DHT22 temperature and humidity sensor. it may fit the DHT11 also. i tested it for a week and i can say that this enclosure does not alter the sensor readings. You can find all my models here , thank you who will…
Wall thermometer with microcontroller ESP8266 and temperature and humidity sensor DHT22 inside the box and cable probe with Dallas sensor DS18B20. Both temperature sensors are optional and it is also possible to connect more cable probes.…
3D model on different extension for creation of cool things.
ATTENTION! Version 1.0 did not hold very well. One of the clips was deformed after some time. I think it could be because of the PLA, but I don't really know yet. I used another solution now. BUUUUT: I made a small improvement and…
DHT22 / DHT11 / AM2302 sensor mount. Mount using zip tie or screws. Category: Electronics
The original design had a paddle for your finger that was prone to being hit by the pull cord handle especially if it slips from your hand. This would quickly snap off the paddle. This design should be less prone to this failure.
DHT22 AM2302 Housing Honeycomb Style This is a housing in honeycomb style for DHT22/AM2302 sensors. Heat up the pin after putting in the sensor and push it down. Thank you to @TueftelTyp https://www.thingiverse.com/TueftelTyp/about for…
The idea behind this case was to create something minimal, sturdy and without any fasteners. The T-Beam is aligned with the case through the use of a brace below the PCB, which locks it into place on the mounts so that there's no sliding…
Desktop weather station based on NodeMCU ESP8266 (CH340), Waveshare DHT22 sensor and 1.3 OLED display. Designed with a dedicated storage compartment for a battery pack of your choice. For me it was a series connection of 3 AA batteries…
Needed a mount for my enclosure to hold the AM2302 (DHT22) temperature and humidity sensor. Didn't see ones I liked that allowed for easy mounting to the 2020 extrusion frame, so I made one. I have seen these boards from Keyes, DSD and…
Hier ein Remix von - Blinddeckel für Busch Jäger Reflex SI Abdeckrahmen von Ma Gu - um einen DHT22 zu montieren.
A quick design for an ESPHome Temperature Sensor. If the ESP board does not seat properly, make sure the edges are filed flush.
Simple case for DHT sensors. The ring can hold in place a mesh filter against dust. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: prusament PET Notes: screw tolerance is…
Um gegenüber meinem anderen Aufbau einen der beiden Festool Staubsaugerschläuche zu sparen und den Saugweg zu verkürzen habe ich die beiden folgenden 90° Adapter entworfen. Funktionieren super und mit folgenden Druckereinstellunden auch…
Habe diesen für einen Freund mit dem Wasserabweiser versehen.Passt genau in die Fronttüren.
These are mini Marathon motor covers for the ⅓ scale XT22 by Nascarsimracing1, Its also compatible with the legacy 3T22, and other siren models that utilize the same mounting pattern. Feel free to save the image of the tag and glue it on…
This little project displays the current humidity and temperature on a 5110-"Nokia" LCD. Additionally it records the temperature of the last 60 seconds, minutes and hours. Based on this data, a graph is drawn onto the lower half of the…
I designed this DHT22 Complete PCB housing snap enclosure as Thingiverse is having mainly the DHT11 smaller type and some DHT22 enclosure with exposed DIL pin. This is a Light and quick print. Only uses 1.89meter of filament and print…
Holder for D1 Mini with shield and LEDs. Optional separator that can be wrapped in Aluminium foil to provide additional shielding
https://www.banggood.com/T220H-2_0-Channel-TPA3251-bluetooth-5_2-Digital-Stereo-Audio-Power-Amplifier-Board-220Wx2-p-2016217.html?rmmds=myorder&cur_warehouse=CN&ID=6290793
This is case for Wemos D1 (ESP8266) and DHT22 based on 3D Printer Monitor for OctoPrint Wemos D1 ESP8266 case. Wemos D1 is running on ESPEasy firmware. Category: DIY
New version for less temperature difference due to ESP heating In this version a measure ca. 0.3°C difference between an open (breadboard) design and the D1 and the sensors in this housing. In the old version it was around +6°C delta.…
Terminal for SSD1306 0,96" Node MCU and DHT22. Desk thermostat and hygrometer.
Simple snap together case for a Raspberry Pi Pico W with a DHT22 temperature and humidity sensor. I programmed the Pico via ESPHome to provide the temperature and humidity readings to my Home Assistant installation.…
I’m using the sensor in my Prusa XL enclosure. It’s controlled via the ESP32 camera . I soldered the wires on the camera side and routed them through the lower ventilation slots of Michael Fanta’s ESP camera case . Inside the sensor…
weather resistant outdoor case for hdt22 temperature sensor. requires 3x m3 thread inserts. 3x M3*4 short screws * m3 hex screw barely fits to hold the sensor, smaller screws/smaller caps may be easier 2 mounts included and f3d file.
Just like the original Hakko B2756 but you can print as many as you need now. I printed with 5 walls, 0.2mm height and 80-100% infill to add some weight to it. I debated adding a lead weight to it but with the tips in it it has enough…
ESP8266 Rack - SSD1306 OLED Display - DHT22 temperature-humidity sensor
This case is for the commercially available presoldered DHT22 sensors. You can find such sensors on AZDelivery. Sometimes they aren’t cut correctly (if you see a grooved white line on the edges); in that case they won’t fit. You can…
A box to mount an arduino featherboard with a DHT22 sensor to a wall. Still a work in progress, pictures will follow. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Filament: DAS…
This time, I came into possession of a T22 without the HDD and the cover. So it is only obligatory for me to come up with something just like the IBM ThinkPad 560Z External SD Card HDD Caddy . With this SD2IDE caddy, you can use an SD…
Fog Light Cover for Toyota Avensis T22 I had a broken glass and in switzerland the car gets checked every x-years. Fog lights are not required so I removed the glass and printed covers that I glued in. How I made/measured this? Layed it…
Contains two DHT22 holders for use on a 3D printer cabinet. One holder has a cutout for a cable.
This is a 1/3 Scale 3T22A (or 2T22A) with WORKING DAMPERS!!! This siren was a collaboration between Nascarsimracing1 and I This siren weighs approximately 9 pounds! Thank you Jared for modeling this, my old modified Edaan B-core may be…
Deets The chain slider on our beat up old XT225 finally gave up the ghost. Ive been wanting to fix it, but it gets ridden a lot. Thankfully the old one broke off so the swing arm didnt need pulled. This model omits the angle for the…
Let me know if you also need other versions like a simplified version or with different pins (for example 90degree). Update: 2025-10-4 small fix in grid coutout dimensions
ARTE&DISIGN GT226 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
Wemos D1 Mini and DHT22 Enclosuse with Neodym Magnetic
Really liked @drwatson6 design, changed it a bit to better suit my needs. Higher tolerance for component placement on PCB (i.e. compensating for poor soldering in the manufacturing) countersunk holes for wood screws stronger pins for…
2x2 Gridfinity bin for Bernzomatic ST2200 with magnet holders
a small box with pin inside that effectively shields and holds a DHT22 temperature humidity sensor. Allows airflow in but not water. I had this set up as an outside air temp and hum sensor for my all sky camera. Printed with the solid…
Enclosure / Connector for a DHT22 / DHT11 / AM2302 sensor. Included are two different methods of interfacing with the sensor: CAT5 Ethernet Keystone Jack Cable Category: Electronics
A simple box for a NodeMCU and a DHT22 on a perf board. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .28mm Infill: 20% Filament: Das Filament PLA mattschwarz Category: Electronics
You will need: DHT22 sensor ESP32 C3 Supermini 4 x 15mm M3 screw 4x M3 heat insert 2004A i2c lcd
This enclosure is designed specifically for the AZDelivery ESP32 Dev Kit C V4, used in combination with a DHT22 temperature and humidity sensor connected via cable. Not suitable for other ESP32 layouts without modification.
ORGANIZZATORE GT22 Realizzato:www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2
Simple wall mount for a DHT22 / AM3202 type temperature and humidity sensor. Sensor gets mounted with a single M2 - M3 screw and nut while the switchplate gets screwed into the wall using 4 tiny wood screws around M3. The hole this mounts…
Made in compass 3d.
This is a bracket mount for the DHT22 temperature and humidity sensor. double sided tape can be used on the bottom or there’s a relief for a round magnet (12x2mm magnet size).
[Update: Sep 22, 2020] I made another mount for the BME280 sensor, too. Find it here: https://www.prusaprinters.org/prints/117039-am2302dht22-sensor-mount-for-extrusion-rail For my enclosure project with a temperature contolled fan I…
ARTE&DISIGN GT222 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
3D-printable case tailored for a 30x70mm board, comprising a DHT22 sensor, ISP32 S2 mini, and four XH connectors. The model comprises two essential parts: a body and a protective cover. Assembling requires = four M2 8mm screws. It is…
A basic case for a temperature sensor built from a DHT22 temperature and humidity sensor and a ESP32 S3 Mini.
Summary Wall mount casing for the Keyes DHT22 / AM3202 module. Enjoy! Watch the making off @ YouTube: https://www.youtube.com/watch?v=jPjaodAKAKo Instructions You only need 3 x M3x8 to enclose the DHT module.
Holds esp32 and dht22 board in a small case with a separator to help prevent esp32 temperature from heating the dht22 3 models to chose.
Electronicsbox, made for a ESP8266 in the D1-mini form factor, with a DHT22 and a MH-Z19 sensor.
I liked the front design, so i remade it a single cradle for the 18 & 20v smaller battery as well.
Print in TPU, no supports, no brim needed (in my case)
ORGANIZZATORE GT224 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2 / X3 PLUS
