Counting matching models…
This filament spool holder is intended for the TEVO Tarantula Pro, but will also work on any other 3D printer with 20X20mm extrusion on its top, or a 20X40, or 60,or 80, etc. extrusion on its top, as long as the 20mm side is facing up.…
This is a very ideal upgrade for every TEVO Tarantula Pro that allows for more sufficient cooling to the power supply. After getting my Tarantula Pro working through following the manual, I noticed that the 24v power supply unit (PSU) is…
For all of you who might feel that your stock TEVO tarantula's hot end is inadequate in that it doesn't have a part cooling fan nor a mount for an inductive sensor, than these parts are for you. The fan vent holds a 5015 fan and provides…
This is a remix of a z-motor mount made by Albatrossity: https://www.thingiverse.com/thing:2754633 The original mount worked mostly well. However I found that the top plate that gets mounted to the 2020 extrusion wasn't thick enough and…
This is a surprisingly simple-to-print hot end fan mount upgrade for the TEVO Tornado. It uses the original two fans that are already on the stock hot end and is very simple to attach onto the X-carriage. It has several advantages over…
Here is my third filament spool holder I made for my TEVO Tornado! This spool holder fits securely into the 20x20 aluminum extrusion on top of the 3D printer frame and can be attached without taking apart the frame. It also includes a…
This is another filament Holder for the TEVO Tornado that rests on top of the electronics control box. I was trying to design something that takes less time to print than my other Tornado filament holder, but this one still takes a very…
This filament holder is designed to rest on top of the electronics box of a TEVO Tornado. I haven't printed it yet, but it should work fine. If you're looking for a more tried-and-true filament holder, check out my 3rd filament holder…
For quite some time, I was bothered by the mechanical stress on the Y-axis endstop, which took a beating every time the bed made contact. After a fruitless search on Thingiverse—where models either didn't fit or had misaligned holes—I…
A strong, stable (very important) and very convenient dial indicator support that is set at the back side of the Tevo Tarantula X-carriage. I use it for manually leveling the bed, and to set the nozzle height at the right distance to get…
A functional Runout Sensor to fits with MK8 Extruder for filament 1.75mm, just print and use it. You need enable it in firmware, I used Marlin 1.1.9, My board is MKS Base 1.4, this mainboard came with my Tevo Tarantula. This changes work…
In this video I will show you how to change your 3D printer back from a problematic auto bed leveling (ABL) system to the reliable mechanical end stop switch. It isn't much work and requires you to only identify the GND and trigger wire…
Da ich oft beim Kabellöten eine dritte Hand gebraucht hätte, habe ich diese Vorrichtung konstruiert und gedruckt.
This is Direct Feed Titan Extruder X-Carriage designed to work the the Tevo Tarantula. This was designed to work specifically with an E3Dv6 Hotend, E3D Titan Extruder, and a Nema 17 Pancake Stepper motor (Link below to dimensions and…
Remixed / adjusted thingirob's Tevo Tarantula Modular X Car Basic X Carriage to accommodate for the Openbuild wheels and Openbuilds Aluminum Extrusion. Wheels fit in the V-Slots better but results in the spacing to be too wide for the…
Tevo Tarantula X Cartridge w/Autolevel Sensor Mount Uses heat press screw inserts in the carriage. Available for purchase here: http://www.mcmaster.com/#94180a331/=118mq8b NOT my design. Forgot where I found it. Want to mod it a little…
Slightly Extended version of my TAZRantula (Tevo Tarantula Mod) Z-Nut Mount. (fixed by Bruce W) Z-Mount Nut Remix created for my custom TAZRantula (Tevo Tarantula duel kit mod). Will work only with TAZRantula (Tevo Tarantula Mod) Z-Mount…
Slightly Extended version of my TAZRantula (Tevo Tarantula Mod) Z-Mount. Z-Mount Remix created for my custom TAZRantula (Tevo Tarantula duel kit mod). Works with single or dual Z-stepper motors / rods. IMPORTANT: Will require the extended…
Z-Mount Remix (fixed by Bruce W) for my custom TAZRantula (Tevo Tarantula duel kit mod). Compatible with upgraded / fixed Z-Nut mount. Works with single or dual Z-stepper motors / rods. Print Settings Printer Brand: RepRap Printer:…
I'm working on a second printhead for my Tarantula since I've earn a nice complete E3Dv6 head - I had taralu parts modular_X_dual_E3DV6 - so let's order the second E3DV6 and see what I can do with a dual E3DV6 head.... First issue : the…
Control box mounted spool holder for Tevo Tornado (staple is optional but it prevents the spool holder from moving). You can use it with Universal Spool Holder Support de bobine fixé sur le boitier de contrôle pour de la Tevo Tornado (le…
This is an adapter for the original Tevo Little Monster electronic case which supports a Duet3D 2 as well as a Rasperberry 3/4B, Bigtreetech PI /Adapter with a hole size of approx. 58 x 49.5mm. The round recesses serve as cable…
In some cases head of the screw hits the extrusion or somewhere... You can solve this problem in a simple way by using "Advanced Endstop Bracket for Tevo Tarantula". Print Settings Printer: Tevo Tarantula Rafts: No **Supports:** Yes…
The original oldham coupler does not fit 3-Wheel X Brackets because brackets are 5mm thicker than default ones. This oldham coupler is 5mm cutted version of https://www.thingiverse.com/thing:2039498 So you will be able to use this oldham…
This is the "without spacers" version of https://www.thingiverse.com/thing:2628544 The spacers came with tevo printer is strong enough to handle preasure but printed ones are not. So i recommend using default spacers. -You will need 4…
null Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: 3D Printing
This is an adapter for the Tevo Little Monster to use 80mm spaced magball arms. I paired this with Asyborg's 80mm smart effector plate. Print this out of PETG or other strong plastics. I used CFPETG and it's quite strong. There's two…
Creality Ender 3 users please read the last update below #ZKNOB This two piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It lets you manually control the hot end up and down (when…
Creality Ender 3 users please read last update below #ZKNOB This two piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; It lets you manually control the hot end up and down (when steppers…
A simple mount for a USB extension cable to mount a key chain LED light (or other things) to your printer's frame. I used a T-nut and bolt that came as spare parts with the CR-10 to mount it to the frame. To use it on the other side, just…
This mod// fix adds a spacer inside the top of hot end that allows a cut length of tubing to be lightly compressed against the nozzle. also taking the extra work of maintaining that seal away from the teeth in the bowden coupler. See the…
This filament spool holder is intended for the TEVO Tarantula Pro, but will also work on any other 3D printer with 20X20mm extrusion on its top, or a 20X40, or 60,or 80, etc. extrusion on its top, as long as the 20mm side is facing up.…
This is a very ideal upgrade for every TEVO Tarantula Pro that allows for more sufficient cooling to the power supply. After getting my Tarantula Pro working through following the manual, I noticed that the 24v power supply unit (PSU) is…
For all of you who might feel that your stock TEVO tarantula's hot end is inadequate in that it doesn't have a part cooling fan nor a mount for an inductive sensor, than these parts are for you. The fan vent holds a 5015 fan and provides…
This is a remix of a z-motor mount made by Albatrossity: https://www.thingiverse.com/thing:2754633 The original mount worked mostly well. However I found that the top plate that gets mounted to the 2020 extrusion wasn't thick enough and…
This is a surprisingly simple-to-print hot end fan mount upgrade for the TEVO Tornado. It uses the original two fans that are already on the stock hot end and is very simple to attach onto the X-carriage. It has several advantages over…
Here is my third filament spool holder I made for my TEVO Tornado! This spool holder fits securely into the 20x20 aluminum extrusion on top of the 3D printer frame and can be attached without taking apart the frame. It also includes a…
This is another filament Holder for the TEVO Tornado that rests on top of the electronics control box. I was trying to design something that takes less time to print than my other Tornado filament holder, but this one still takes a very…
This filament holder is designed to rest on top of the electronics box of a TEVO Tornado. I haven't printed it yet, but it should work fine. If you're looking for a more tried-and-true filament holder, check out my 3rd filament holder…
For printing, I used natural PLA from Bestfilament.
Stands the main board off the tower enough to clear the BLTouch on the V4 fan duct with large bed. Without this, the BLTouch hits the board at the far end of travel. Use the existing t-nuts to lock the riser in place and some additional…
I wanted to put an E3D knockoff on my Tevo tarantula so I designed an X-Carriage and cooling solution to accommodate it. Required HW: 10 M3 Square Nuts 1 M3 Hex Nut 7 M3x10 Screws (I used hex-head Caps) 2 M3X25 Screws 2 M3X30 Screws The…
Hotend mount for the e3d v6 on the Tevo Tornado, it might also work with the CR-10 but I did not test that. I switched from my anet a8 to the tevo tornado and I missed the e3d hotend (I had a e3d v6 on my anet). The printquality of the…
Cable chain for the heatbed of the Tevo Tornado, it might also work with the CR-10 but I did not test that. I switched from my anet a8 to the tevo tornado and I missed the cable-chain for the bed. Especially because there is no…
This is a clamp designed to level your bed with the help of a dial gauge. With this clamp you can attach the gauge to your hot-end (single and dual nozzle) and make sure your bed is level by a precision of 0,01mm. The clamp is simply…
This is a replacement for base.stl in https://www.thingiverse.com/thing:1957761/ that includes cutouts to reduce printing time and adds a spot for a marine screw terminal to be connected. It reduces the print time on my Black Widow from…
I'll start by saying I've yet to confirm whether this fits the TLM printer. I don't know if this will work with the original Box that came with the TLM. The board carriage may be too long. I made this from scratch using FreeCAD. I've…
I'll start by saying I've yet to confirm whether this fits the TLM printer. I don't know if this will work with the original Box that came with the TLM. The board carriage may be too long. I made this from scratch using FreeCAD. I've…
[Update 2] Got fed up with missing Z height. So I moved the chain behind the Z rod with a couple extensions. The X carriage extension is for the LPA Modular X carriage at https://www.thingiverse.com/thing:2034743 . [Update] I created a…
Replacement gasket for the Titan extruder in order to use a PC4-M6 fitting instead of the original PC4-M10. Snug fit, self-tapping. Only tested on a Tevo knockoff.
Bowden tube support clamp for the original Tarantula carriage. In some circumstances (high Z or short tube), the bowden tube tends to overflex just before the hotend. This clip snaps directly on the original carriage, providing a more…
GIRO - TEVO Tarantula / Y-Axis Motor Mount General This Nema17 stepper motor bracket was designed to improve the Y-Axis movement by reducing the friction of the idlers due to the fact that if you want to tension your system properly then…
GIRO - TEVO Tarantula / 608 Ball Bearing X-Axis Idler General This idler was designed to be mounted on the X-Axis of the TEVO Tarantula and uses 608 ball bearings. This idler is also usable for other printers with a 4020 extrusion profile…
GIRO - 608 Ball Bearing Y-Axis Idler General This idler was designed to be mounted on the Y-Axis of the TEVO Tarantula and uses 608 ball bearings. This idler is also usable for other printers with a 4020 extrusion profile as an axis.…
GIRO - TEVO Tarantula Heatbed Holder General This heatbed holder was designed to manually move the heatbed across the Y-Axis. It should prevent to touch a hot heatbed by accident or to prevent that you have to touch the printsurface after…
GIRO - 626 Ball Bearing X-Axis Idler General This idler was designed to be mounted on the X-Axis of the TEVO Tarantula and uses 626 ball bearings. This idler is also usable for other printers with a 4020 extrusion profile as an axis.…
If anyone still has a Tevo lm and want to use an HGX Extruder. Also added a mounting spot for an adxl345 You need 2 M3 Inserts for the adxl345 mounting point
This is a modification of paul0's Coolatron fanduct. I printed the original, but noticed the airflow was inadequate. So I spent an hour further hollowing it out in tinkercad. This version seems to have at least double the airflow when…
This is a small and simple, yet absolutely essential part that Tevo "forgot" to supply with the Little Monster (may be usable with other printers as well). According to the printer's assembly manual, the geared belts that hold the flying…
This is a cap covering the pulley sides of the Little Monster's (or any equivalent delta printer's) X, Y and Z motors, just to keep dust off the gears and make the printer's look a little less "raw". Application is easy: Just print it,…
When cabling the Little Monster's logic board it's a pain in the a** that you have to lead the cables through the holes in the back of the board's enclosure, meaning that the enclosure is always in the way and can't be taken off while you…
Having a prime blob on a Delta printer is somewhat tricky if you don't want to sacrifice too much printing space. For mine, I decided to split it into four movement commands along the outer edge of the base plate, stealing no more than 3…
Description: This is a "stopple" for the 50 mm hole in the LM's top plate that fulfills three tasks: Stuff the hole, so hot air is kept inside (if using a printer enclosure) Integrate a swivel-mounted filament detector Integrate a temp…
This is a replacement for the Little monster's stock filament spool holder. It is fully compatible with the spool holder system I originally published with the HomeCube enclosure project (…
Modeled this to hold a 9.5 x 9.5-in glass plate to my Tevo Tarantula Pro's heated bed. Slides in between the aluminum plate and the foil insulation and is held in place by the leveling spring tension. Print with PETG or ABS for heat…
This is just a simple remix of gdramos' design . I removed the 2 unneeded screw holes to make it a little more aesthetically pleasing. Tested both on my Tevo Tornado and Tevo Tarantula Pro.
This is a remix of the Raspberry Pi + LM2596 mount from achmed20 . I've made it a little thinner for faster printing. Since it's not a structural part of the printer this should have no effect. I also added a notch near the SD card slot…
This is a remix of mikey5959 filament sensor support for use with the BTT Smart Filament Sensor. Once printed, remove the bottom cover plate from the sensor and screw the mount in from the bottom. I used 5 M3x12 screws, but I think as…
Remixed for my Tevo Tarantula Pro. It uses the stock IEC plug and switch assembly. Screws Used: 8-10 x M4 Screws (4 for the PSU mount, 2-4 for the base to frame, 2 for the top mount to frame) 4-6 x M4 T-Nuts (for the frame mounts) 2 x M3…
Modified version to fit the new Tevo Tornado Gold edition. 2mm correction on the screw tab. No need to move the Y limit switch, even with dampers installed. Enjoy! Category: 3D Printer Accessories
Y-Axis Belt Tensioner (Face-Mounted, Composite-Optimized Clamp) A rigid, face-mounted Y-axis belt tensioner for Tevo Tornado , CR-10 , and similar machines using a 2040 Y center rail mounted on a 2020 cross extrusion . This design…
Y-Axis Motor Mount (Composite-Optimized Reinforced Bracket) A high-strength, composite-oriented Y-axis motor mount for the Tevo Tornado and CR-10 family. This mount replaces the thin sheet-metal bracket with a rigid, vibration-damped,…
This is my version of the Y axis Linear Rail mod for the Tevo Tornado. You only need to drill the two center mounting holes in the aluminium bedplate. Hardwear: 2x MGN 12H 400mm linear rails…
This is my version of the Z axis Linear Rail mod for the Tevo Tornado. I've added way more than just the liner rail Z mod but just use what you need. WARNING: This Z linear rail mount mod will expand your x axis length a few mm and will…
This is my version of the X axis Linear Rail mod for the Tevo Tornado. WARNING: USE THE (X_MOTOR_MOUNT_PULLEY) if your also installing the Z linear rail mod. The size and spacing of the motor mount has been adjusted for the Z Linear Rail…
Work in progress For now, only the right part was changed
This adapter allows you to mount the stock CR10 (not tested) or Tevo Tornado (Tested) metal x carriage mount to an MGN12 H rail. Just need to print the adapter, and re mount your rail. Tips: When mounting rails they MUST be centered. I…
This Remix allows you to use the Creality CR-10 Titan Aero Mount on a MGN12 rail. Changes to the original Removed the smaller holes that would have been used to mount to the Tornado metal plate Added two holes to mount to the MGN12…
This is a stabilization bracket for the Tevo Tarantula printer. In the stock printer the Z-Axis 'floats' on the flexible shaft coupling which creates some vibrations and compromises rigidity. To install this you need 1) a standard 8x22x7…
Here are some adjustable bed mounts that allow you to change out different pieces of glass quickly with no hardware needed. Printed with PC Carbon. The mounts will accommodate glass plates from 300mm to 310mm and up to 5mm thick. Print…
For quite some time, I was bothered by the mechanical stress on the Y-axis endstop, which took a beating every time the bed made contact. After a fruitless search on Thingiverse—where models either didn't fit or had misaligned holes—I…
Original files here: https://www.thingiverse.com/thing:4336908 THIS MOD WORKS WITH ORIGINAL FILES FROM 4336908 ENGLISH Same files as original but..... Files: Directdrive-BMG-V6_Mount-Back-for-inductive.stl Back of the mount with holes in…
A cover for the control box of the tevo tornado and CR10 to block the bright light Print Settings Printer Brand: TEVO Printer: Tornado Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Category: 3D Printer Accessories
Long time ago, Amazon was a treasure trove for those of us who provided HONEST reviews in exchange for products. Amazon put a stop to that, but back then, one of the items I scored was an endoscope camera. I used it a few of times so I…
The control boxes on Thingiverse for the Tevo Tarantula were all too big and tried to incorporate everything into one case. I like the power supply sitting there all naked, and I'd already designed a case for the MOSFET expansion board so…
Never being one to be satisfied with the status quo, I wanted a control knob that would compliment my new purple case , and the original blue insert just didn't work. I wanted white, so I designed my own. Yep... it's super simple, but I…
I like the use of the clear acrylic panels for the mainboard and for the LCD control board. I like to see my electronics (mechanical workings, too). The problem with this, though, is that the sides are exposed. That is very bad for…
I have been using the small binder clips to hold the sheet of glass down to the heatbed, but today while installing an aluminum plate, I noticed that the LPA fan duct was hitting the rear clips, thereby raising the x-axis gantry the…
I am printing parts for my Tevo Tarantula in purple so that it can have a purple/black theme going on. To that end, I wanted a purple knob. So... I made one. Or rather, I made two. The first version is a straight sided knob with a hollow…
Osiak's X belt tensioner works really well but the original belt holder lifts the belt by about 5mm. This causes inaccuracy in x movement as the belt becomes a hypotenuse in a right angle triangle and thus the actual carriage movement is…
Adjustable z stop for Tevo Tarantula, designed to be narrower and simpler than others I have seen. The mounting bolts of both pieces are easily accessible. The adjusting bolt is held by a hex nut top and bottom which keeps tension without…
I made this for my needs, because I'm using my own side spool holder. Just unscrew the nut enough to glide the piece so the notch fits on screw's axis, then re-tighten. v2 : slight rework of the torus ring in order to enhance bed…
This is designed to slightly compress air and head the flow efficiently. Printable without supports. Recommended settings \_/ Ø 0.4 Layer height 0.25 Perimeters 2 Infill 20% Bottom & Top 4 4 Supports
Features : • A little window to look trough for viewing the nozzle • Holes on top to help the heat dissipation • Supports for blower fans • Wedges to hold the blowers for easier screwing • Ducts that slightly compress the air for more…
Tevo's Titan extruder clone doesn't fit Elzariant's E3D Titan mounting plate, plus I wanted to mount mine with the hot end on the side closer to the rail, so I made my own starting from the empty plate .stp file. Print Settings Printer…
It's a display and board stand for the Tevo Tarantula that keeps all the fancy clear acrylic pieces. Print twice, with one of them mirrored. Supports are helpful for the upside-down countersunk holes in the base, but not strictly…
This is a re-designed version of the direct drive extruder mod from Granitoid. I had to adjust the holes placement since they were not fitting the ones of my aluminum carrier. Furthermore I added a hole for the hot-end cables and a hole…
PTFE tube attachment for Tevo Tarantula direct extrusion mod. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.16 Infill: 25% Filament: Polymaker Polyflex TPU Black Category: 3D Printer…
![[2x REMIXED] Tevo Tarantula 3-Wheel X Brackets](https://media.printables.com/media/prints/1080031/images/8166886_08e6c378-4e77-41e3-92df-e20035b6df0d_303a1063-5369-4216-a069-a635c06b5245/7f3d58b193ac4ce8e0730da9d0d6e8ce_display_large_1080031.jpg)
![[Remix/Mod] Coolatron V2, fanduct for Tevo Tarantula using 50x50x15 Blower](https://media.printables.com/media/prints/149108/images/1401359_c9ba934f-aee3-4ad5-8fc6-c4a70e3ab279/dd52d299c67ef5dfee6973e8019fba20_display_large_14.jpg)
