Liczymy pasujące modele…
A quick print tool to calibrate your e-steps. Print the device and then measure the outside edge of all legs to determine if you need to adjust your e-steps for the axis on your printer. New test piece to check X, Y, and carriage Skew
Speaker pod with a 40 degree mounting angle at various heights and axis angles. The pod was designed to fit the Infinity Kappa 1in tweeter and 3 inch Kappa mid. If you don't want to use the supplied Infinity grills you can print the…
This is a bat top replacement for the Arcade1up joystick with ball tops. Bat tops have a much better feel to me so I quickly made this to replace the ball top on my machine. Have installed these on three different machines without issue.…
It never fails. I always seem to have a partial spool of filament that isn't enough to do a project with. This is my attempt at using all my partial reels of filament. You simply clamp the two pieces together and slide a piece of filament…
Speaker adapter ring that allows the removal of the stock speaker and replacement with after market. Requires the use of one of the screws used to secure the stock speaker. The adapter was designed for a 2007 Chevy Avalanche but will most…
A quick print model for M3, M4, and M5 tnuts. Printed the test pieces in PLA with 100% infill and no supports.
If you have a router that has a 2.4 inch span between the mounting bolts, this circle jig should fit and allow you to cut the most standard size openings for woofers. The jig is set to cut 6 - 21 inch circles. The selectable dimension…
This is a drop-in replacement for the Arcade1up restrictor-plate found on the Gen1 and 2 Street Fighter cabs. This will replace the 4-way restrictor-plate allowing for a much more fluid circular motion. The real arcade cabs used 8way…
Custom Mini ANL fuse distribution system. The fuse terminal is designed with a fuse/terminal plate and an isolation plate. If you will be mounting the fuse/terminal plate to wood or other non-conductive surfaces you can choose if you want…
E-step adjustment tool. After replacing belts on my machine I was having issues with parts fitting together. A standard calibration piece showed no issues. It wasn't until I made this tool that I found out my carriage was out of square.…
Higher capacity tumbler bowl for the HarborFreight 5lb tumbler. It is designed to use the original bowls gasket and lid. This bowl also has a higher side wall angle, increased height of the center post, decreased diameter of center post,…
I was in need of a custom battery tray for 20 Headway 38120 LifePo4 cells and a balance board. This design allows you to install 20 cells and configure them in any manor you desire. I used this setup for a 4s5p battery arrangement. My…
ANL fuse block/holder/terminal Designed to use either 1/8in or 1/4in thick x 2in wide aluminum flat stock for the busbars 5/16in x 1in bolts (thread pitch your choice) 1/4in x 5/16in bolt (thread pitch your choice) The top busbar is 2in x…
Had an install where the person wanted the companies name used as the grill cover and they wanted it back lit. This grill is connected to a speaker cover plate that mounts to the sub box with magnets. The grill itself is epoxied in place…
I purchased a Haldis extruder as an upgrade to the stock Ender extruder. The only down side is the Haldis isn't a direct swap for the stock extruder. I wanted to use the Haldis extruder in a direct drive upgrade but couldn't locate a…
A recent subwoofer enclosure got so bulky it was very hard to lift, due to awkward size. The total weight was around 165lbs spread over a 4ft x 2ft x 2 ft area. By adding a couple of handle ,the box is able to moved around much easier.…
This box was designed to house the Bulvack LM2596 DC to Dc buck convertor, from Amazon. We use these convertors to adjusted voltage in vehicles, printers and some small automation applications. The box is not water tight but it house the…
The is a custom designed power distribution block for a car audio system. I was needing a 6 terminal ground block and couldn't find anything I liked so I designed this instead. Included are the block and base plate. You will need to cut a…
I never seem to have enough spools to put new color filament on. Instead of buying them I just decided I would print them as needed. This spool is designed to work with the Inland Spoolless filament. The spool core diameter is 3.6 inches.…
The oil filter on the 07 avalanche is a pain to get to with a traditional oil filter wrench, so I decided to model a socket style wrench to remove the filter. The wrench was tested on the Microgard and Wix 57060 filters. It should fit any…
This is a remix of the Riemenspanner Y belt tensioner for a Ender3. I have remixed it to work on the Ender 5 plus. The side mounting tabs have been added to allow it to be secured. The standard bearing can be used with this design but it…
The first image - Complete Intex Leaf catcher system with cloth mesh filter and printable replacement filter. The second image - Replacement filter inside of leaf catcher body and TPU gasket installed. The cloth mesh filter being replace…
They say necessity is the mother of all inventions. I needed a pivoting mount for a monitor on my reloading bench. I came up with this design to fit my needs. It has two different monitor mounts. The file labeled monitor_mount_HR.stl…
Single and double J-Clips for securing power wires in 1/0 gauge or 4 gauge size. The file labeled fan_jclip.stl works well for securing flat 3 wire fan leads or smaller single wires around 18 gauge or smaller. Designed to be secured with…
I made a couple different pickleball paddles, based off of a wide body paddle measurements. The paddle should be within pickleball specs provided no dimensions are changed to be larger than the current model. Minimum print area is 12.5 x…
After playing the 16mm paddle for a month we decided we wanted a little more pop so… There are two versions of the paddle and two versions of the handle. The paddle has a .325 and .425in hex core. The .425 paddle has a little more pop but…
I have been tweaking my E5P trying to get the print speed up. Around 200mm/sec I was seeing the frame tweaking during rapid direction changes. I designed these braces to help reduce the frame flex I was seeing. Print with your standard…
A speaker alignment tool designed to use a .500inch laser pointer to help pin point the on axis point of a speaker. Place the tool on the mounting surface of the speaker and ajusted the secondary arm to determine the angle from the…
Finally burnt up the tips on my original cooler and designed this one to work with the Ender 5 Plus, fitted with a Sprite Pro extruder and a DragonFly BMS hotend. The cooler arms mount to the side of the Sprite extruder with 4 - M3 x 10mm…
Yet another change/upgrade. This paddle has a 16mm thickness to give more ball control. The core and frame have been redesigned to lighten the paddle and keep it around the 8 to 8.5 ounce weight range. The attachment socket of the paddle…
A non-conductive screw driver for adjusting amplifiers, crossovers, and other electronics that you don't want to risk shorting out with a metallic screw driver. Printed with a .2mm nozzle and 15% infill. Printed with the handle of the…
This is a low power magnetic terminal designed to be used as the power connection for some LED strip lights. By using the magnets this allows the terminal to be disconnected, isolating the power. When installed the total line resistance…
Another week, another change… This paddle is based off of the 13.5mm paddle I printed. We added an opening through the paddle to reduce weight and the handle was changed to allow for more grip room. The paddle was printed from PETG while…
My answer to a top mount filament spool holder. I was running a reverse boden tube with a top mount spool holder but my drive would crash into the spool if I worked to closely to one end of the bed. This spool holder resolved that issue…
I made this block to help me align my gantry on the X1 and X2 axis while tensioning the belts. To use: Slide the blocks over the front or rear Y-Axis support rail Push gantry against the block Tighten your belts with equal tension. Move…
This is a mount to allow the Down4Sound MiniMax amplifier to be mounted in an inverted fashion and show off its' guts. This mount will give about .050" clearance between the top of the amp and the mount surface, to allow for airflow. I…
Building on what I learned from the first couple of paddles I made… This paddle is 13.5mm thick, with a different core design, frame width, and face thickness. I printed the paddle in PETG with 25% gyroid infill. 5 vertical walls 6…
A simple angle mount for the Dayton 408 DSP that allows it to be elevated off the mounting surface. Give enough clearance to allow for RCA wires to be installed below chassis of the DSP. Originally designed to allow for the surface…
I recently changed from Marlin to Klipper and noticed an issue with my bridging. I made this model to check different length bridges as well as bridge angles. This tool will help you dial in your bridge settings and diagnose issues with…
Broke the handle on my roller, while applying some sound deadening mat. I whipped up a small and medium roller to keep the project going. Printed from PLA: Recommend printing the roller standing up and the handle laying on either flat…
Another need it make situation. A wiring cover for a recent car audio install I was working on. The cover measures 7in x 2.5in OD and 6in x 1.5 in ID. I used this to cover a dual run of 1/0ga power wire into an amp rack, giving it a…
I recently upgraded to a Phateus Dragon UHF hotend and needed to change up my mounting system and cooling options. I decided to go with a more modular design so future upgrades only required minimal parts design/swap. This is the fruit of…
Instead of measuring for all the screws in a subwoofer box I decide to make a simple jig that has multiple holes set at a .500inch between centers. Now I simply measure for the first hole then make a second measurement to align the tool.…
This is the planet gear carrier for a 2007 Avalanche with electric seat controls. The early 2000's GM vehicles with electric seats had a common issue with this and the main ring gear breaking. I had issue with my Avy and have been looking…
This is a hopper adapter for the Central Machinery Portable Abrasive Blaster, from HarborFreight. SKU: 59490 The tool works great, with the exception of the supplied media hopper. The stock hopper is quite small and leads to a lot of down…
I had to re-wrap several Headway 38120hp cells so I made this guide to get a consistant length on each shrink wrap I cut. Made for 70mm flat measured heat shrink. Just slide the heat shrink in the slot at the end. Pull it through the…
To wszystkie aktualnie dostępne wyniki.
