Liczymy pasujące modele…
This is a case/tray for the Corne v3 (although it should fit all variants). There are options for both choc or MX builds, and with or without optional tenting. The Choc version uses M2 heatset inserts in the base to fasten the plate to…
This is a gasket mount case design for Piantor. Both five columns and six columns are supported. The top and bottom pieces are fastened with 6mm x 3mm neodymium magnets. There is optional tenting via M3 heatset inserts. The ‘noheader’…
These are gasket mount case designs with optional tenting for KLOR. All four variants are supported. The top and bottom pieces fasten with 6mm x 3mm neodymium magnets. The optional tenting fastens via M3 heatset inserts. The lid pieces…
UPDATE 5/6/24: Adjusted the OLED cutout in the lids to align properly with the actual OLED. Should be fixed. Removed the sandwich and top mount versions. UPDATE 2/13/23: I added a 5x3 version of the gasket mount case. This is a high…
Switch blockers for encoder shafts and for covering up unused key slots in your layout. Your milage may vary depending on your switch plate though when it comes to the fit and tolerances for both the switch blockers and encoder blockers.…
This is a bumper I made for my Brila wrist rests. Over time the bottoms of my Brila pads became not so sticky. So I made this to punch it up a bit and to add some low pro silicone to the bottom. I used the leftover bits from a sheet of…
This is a case for the low profile Choc Sofle. The top fastens to the bottom via 6mm x 3mm magnets. There is optional tenting via M3 heatset threaded inserts. Inserts:…
This is a case for the FFKB by Fingerpunch. It prints in 5 pieces to fit on an Ender 3 or other similarly sized printer. UPDATE: I made a 5-col version for all you crazy 5-col users. UPDATE V4 Sept 6, 2022: Cleaned up the file names and…
This is a gasket mount case I designed for the Eternal Keypad v1.2 that adds optional tenting via heatset threaded inserts. The case design incorporates all the plates (FR4 switch plate on top and FR4 or acrylic on bottom). There is a…
This is a gasket mount case design for the FFKB. All versions should fit. This model is untested as I haven't had time to print it, but it is the same dimensions as my FFKB sandwich design, so it should all fit just fine. But print at…
This is a tenting case for the Avalanche v4 ( https://github.com/vlkv/avalanche ). To add the tenting legs you will need to use M3 heat set threaded inserts and M3 screws. There are variants for the 60% and the 40% versions, as well as a…
This is a high profile gasket mount case with optional tenting for the Draculad . It fastens with 6mm x 3mm magnets. The bottom of the base is cutout and will fit a light diffuser for that sweet, sweet underglow. Magnets:…
Tray design for the Cantor. Three design: Tray with 2mm bezel, wedge tray with 5 degree tent, tenting tray that requires M3 heat set threaded inserts and tenting legs. The tray is designed to allow for some rubber bumpons/feet that go on…
CHANGELOG: 12/14/23 - V2 Updates (Inserts version only): Fixed the issue with the 5mm gap between the middle piece and base piece(s) magnets. My bad. Also remove the chamfer directly beneath the middle piece for a more refined aesthetic.…
A trackball housing for a 34mm trackball.
This is a gasket mount case for the Murphpad by MechWild. It fastens with 6mm x 3mm magnets and optional tenting via M3 heatset threaded inserts. I've only modeled a switch plate for the traditional numpad layout with 1.5u mod keys under…
This is a case design for Ximi by fingerpunch.xyz. The case is designed to accommodate both pointing devices, Cirque and Trackball, and you can hotswap them between halves. There is also a tenting wedge that snaps to the bottom of the…
This is a case design for the Helix ortholinear split keyboard. There are designs for both 60% and 40% variants. There is also optional tenting and underglow. The top lid fastens to the base via 6mm x 3mm neodymium magnets. The lid is…
This is a gasket mount, shadowline case I designed for the Eternal Keypad v1.2 that adds optional tenting via a 8 degree tenting wedge. The case can accommodate the top FR4 plate via the switch plate spacer. There is a switch plate option…
This is a gasket mount keyboard case for the Cantor. It has a vaulted switch plate design and fastens the top lid to the base with 6mm magnets. There is an MCU cover which also attached with 3mm magnets. There is optional tenting via M3…
This is a low profile gasket mount case for the Zodiark split keyboard. It consists of three parts per side, plus tenting legs if desired. The top and bottom pieces fasten with 6mm x 3mm magnets. There is optional tenting via M3 heatset…
This is a low profile case for TOTEM by GEIST . It was inspired by the case designed by GEIST themselves with increased tolerances for printing on an FDM printer. It fastens with M2 heatset inserts in the lid. Only wired builds are…
This is a gasket mount design for the Vulpes Majora in 6col and 5col format. It is configured for the PER56 plus trackball setup. There are only three major pieces to print, not including the trackball housing, encoder ring, 5-way switch…
This is a gasket mount case for the Nijuni with optional tenting. It is a very similar design to my Corne Chunky case. It prints in 3 parts per half and requires 3mm foam gaskets for a very nice typing experience. The top piece fastens to…
This is a low profile case for the Zodiark split keyboard. There are options in the files for different configurations. You can optionally add m3 heatset threaded inserts (…
This is a case for the Duckboard. It will fit all versions. Print the top with or without supports, but they aren't required. The bottom will require supports. The case is designed to incorporate all of the plates with the duck visible on…
This is a gasket mount vaulted switch plate case design for the Hillside 48 (non-splay version). The top and bottom fasten with 6mm x 3mm neodymium magnets. There is optional tenting via M3 heatset inserts. The diffuser piece for…
This is a WIP case design for a split using PS2 sockets to connect both halves.
A circular case for the Sunflower PCB by testamatta. https://github.com/hide-key/testamatta
This is a design for the Rock On v3 by fingerpunch.xyz. It is gasket mounted and fastens with 6mm x 3mm magnets. The top prints in 3 parts and the base prints in 2 parts and will fit on an Ender 3 sized printer. The base also has small…
This is a case design for the Sweeeeep by fingerpunch , wired version only. It is a gasket mount design that fastens with 6mm magnets and has optional tenting via M3 heatset inserts. The case is super low profile, with only 5mm between…
These are case designs for the Sweet16 and Super16 macropads by 1UPKeyboards . All three are marked as RC1 (release candidate 1) because I made them an age ago and haven't had a chance to update them since. These were designed for the…
This is a gasket mount case design for the ChonkyKong by weteor . I have uploaded .STEP files for the switch plate. There are so many different variations that I could not generate a switch plate for them all, so I have included the files…
This is a gasket mount case for the Barghoot by AlaaSaadAbdo . It fastens with M2 heatset inserts from the bottom of the case, through the underglow base into the top piece. The switch plate also accepts M2 heatset inserts for securing…
This is a case designed for the Ursula 40% by jimmerricks for both MX and Choc variants. It has optional tenting baked into the design via M3 heatset threaded inserts. The design is a vaulted switch plate, gasket mount design that fastens…
This is a case design for the Porcupine PCB, but only supports the 5x3+4 version with four thumb keys. The top fastens to the bottom via 6mm x 3mm magnets. Magnets:…
This is a case for the Rock On v2 (and also v1) keyboard by fingerpunch. It is designed to print in 5 pieces for printers such as the Ender3 or Ender5. It fastens with M2 heat-set inserts on the underside of the switch plates and 10mm M2…
This is a gasket mount case design for the Boardrun Classic, available at mkultra.click. The case is designed to be printed on printers such as an Ender3 in multiple pieces and assembled. It fastens with 6mm x 3mm neodymium magnets and…
This is a gasket mount case design for the Boardrun Bizarre, available at mkultra.click. The case is designed to be printed on printers such as an Ender3 in multiple pieces and assembled. It fastens with 6mm x 3mm neodymium magnets and…
This is a gasket mount case design for the ZodZero by splitlogic.xyz. It features optional tenting via M3 heatset inserts. The top piece fastens to the bottom via 6mm x 3mm magnets. The light diffuser on the base needs to be glued in…
This is a gasket mount case design for the KONG by Weteor . It fastens with M2 heatset inserts and M2 hex top screws. There are two lids I modeled for the full bottom row or to block the outer keys on the bottom row. The gaskets are 3mm…
This case is designed for the 30%, five column variant of the Ursula created by jimmerricks . The case is a gasket mount design with optional tenting and optional underglow. The gasket material I used is linked below and cut to size. The…
This is a case design for the Ursula by jimmerricks with optional tenting. The top and bottom pieces fasten with 6mm x 3mm neodymium magnets. The tenting is fastened via M3 heatset inserts. Magnets:…
This is a case design for the Pierce Wireless 2.0 by durken1 . It is a top mount case that fastens with either 6mm x 3mm neodymium magnets or M2 heatset inserts in the lid. It also features optional tenting that fasten via M3 heatset…
This is a tray case for the Tern 30-key keyboard.
To wszystkie aktualnie dostępne wyniki.
