242 modeli
Eine Verbindungsdose zum Verschrauben für 3 Stück Wago 221 2411 Durchgangsverbinder. Die Zugentlastung erfolgt mittels Kabelbinder. Kabel Durchmesser ca. 9mm Das Gehäuse ist anschraubbar und der Deckel kann mit M3er Schrauben oder 3mm…
Wydruk około 1,81 €–2,21 € nettoWstępna wycena dla PETGMateriał u źródła: PET
(English below) Erweiterbare Mehrstockklemme für Klemmen WAGO 221-2411 zur Montage auf einer 35mm-Hutschiene: Diese Mehrstockklemme besteht aus einem Grundmodul, welches auf einer Hutschiene aufgerastet werden kann, einem Aufsteckmodul,…
Wydruk około 0,63 €–0,77 € nettoWstępna wycena jednego wariantu
This is a tray, for use with Robert_28442s modular tray system . The concept is simple: Why not utilize WAGO clamps in a 19" non-DIN rack environment? For rack builds, who want to utilize WAGO 221-2411 clamps, either without din rails or…
Wydruk około 0,80 €–0,98 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Update 1: Small optimizations to the casing Added a small groove for lifting the lid Added some space inside on the back for potential cables Hello, here's a small project that I designed. I wanted to combine a small ESP32-C3 Super Mini…
Can be used for DIY RC Airplanes, education and more. If you want other models of NACA airfoils, feel free to comment. Included models; NACA-0012 NACA-0015 NACA-1812 NACA-2212 NACA-2312 NACA-2408 NACA-2412 NACA-4412 NACA-5416 NACA-7712
Please comment, rate, and post a make! Update 2/1/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options. A simple case for using an LD2410C radar sensors with an…
NACA Airfoil 2412. I use this for a test print for new materials or different settings. Uses surprisingly little filament for its size. Print instructions Suggested settings: one perimeter zero top and bottom layers gyroid infill 15%
Case to hold a LD2410 MMWAVE sensor module and a Wemos D1 mini board. The radar module can be rotated horizontally to adjust the angle and direction it is sensing. Four parts: The case that holds everything A holder for the radar module.…
This model is compatible with the lego system.
Model for mounting 3x WAGO 221-2411 Inline Connector to standard DIN rail. Best printed on side for strength.
Please comment, rate, and post a make! Update 1/19/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options. A simple case for using an LD2410C radar sensors with…
WAGO 3-way junction box. Suitable for 3-wire cables with a maximum cross-section of 1 mm². The cover is attached to the box using four thermal inserts with M2 threads. The screws require 5 mm.
Update: Die 3er Variante wurde hinzugefügt. Update: Die 4er und 5er Varianten waren fehlerhaft und wurden nun korrigiert. Update: Ich habe noch eine 5er Variante hinzugefügt. Update: Ich habe noch eine 4er Variante hinzugefügt. Ein…
Spliced together a few different files to fit my own requirements. You may need to re-size/check the carrier dimensions depending on your own ESP32 board. I designed this to use with Jumper cables, i didn't have a screw for the DHT sensor…
After the second world war Alsthom (still with the letter “H” in the name) build 130 diesel electric locomotives for the Nederlandse Spoorwegen (Dutch state railways). They were based on a standard for locomotives in France and the French…
This case has slight changes to it and is based off of Digital Juice 's. This update fits the LD2410 with or without dupont wiring and the USB C version of the D1 mini ESP8266. I included a text file of the .yaml file that is working for…
Case for HLK-LD2410C mmWave & D1 mini ESP8266 to be added in a room or to be put on a wall. Material used for printing: PETG
The model has multiple axes of rotation and is quick to assemble. You can also remove unnecessary parts of the fastening mechanism! This model additionally uses 8x3 magnets and 2x8 bolts. The software can be found on this page :…
This model is compatible with the lego system.
This wing is fully functional, it was made out with the NACA-2412 airfoil, the same used in the cessna 172, the flap, extends and retracts as in the real life passenger airplanes. It can be done fully 3d printed, but the weight would be…
I needed a Case for the LD2410C which fits a d1 mini or esp32 d1 mini, so i designed this one.
The Wago 221-2411 is a popular spring clamp splice, perfect for quickly connecting e.g. the LED bar or fans on the top of an enclosure to the power supply in the bottom. The model provides a way to clip multiple instances together. If you…
Caja para D1 Mini y LD2410
Wip. Replacement for cabin filter cover Renault Laguna 3 52410566. Please notify me in the comments about inconsistencies. Print Settings Printer Brand: Tronxy Printer: Tronxy X5SA/X5ST/Pro/2E/D01 Plus Rafts: No Supports: Yes Resolution:…
Ce projet DIY est non seulement accessible et économique (coût total d'environ 7€), mais il est également personnalisable pour s'adapter à divers scénarios de domotique. Que ce soit pour allumer les lumières en fonction de la présence ou…
No supports needed. Model in picture printed on Prusa MINI with PLA.
Eine Verbindungsdose zum Verschrauben für 2 Stück Wago 221 2411 Durchgangsverbinder. Die Zugentlastung erfolgt mittels Kabelbinder. Eine Seite für Kabel Durchmesser 9mm , die andere für Kabel 4x6mm.
This model is compatible with the lego system.
The firmware can be found on the official website esphome
I was in search for a case for the popular LD2410B radar presence sensor. However, non of the versions I could find matched what I was looking for. I had LD2410Bs with and without headers here. I also ordered different USB-C breakout…
1st test print with these settings, I think you can get away from the Agua Blue, didn't really add too much to the print. Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA PolyLite Azure…
Human presence sensor housing, could not find any casing for the older ESP 8266, this is my first design so, feedback are welcomed Printed with a 0.2 resolution. Use 4 wall layers if to avoid infills on the lid. Screws needed: 2x 25mm M3…
This model is compatible with the lego system.
A wall mount radar presence sensor with a LD2412 that gets directly attached to the Wemos D1 Mini Esp32. EspHome and Home Assistant recommended. Fitting yaml is provided as txt (restriction from printables). Instructions: bend the pins of…
This is a low profile VESA mount adapter for the Acer R241Y. The adapter is strong enough to hold the monitor in both landscape and portrait mode. The tougher filament you use the better but even PLA perfoms well and without deformation.…
Case for a LD2410B combined with a ESP32-C3 SuperMini. No supports required.
Radar dish support for HLK-LD2410C motion sensor mmW 24GHz. Printed with 0.4 nozzle, PLA, with organic supports.
Case designed to fit following components from Aliexpress. There are many clones and alternatives out there with very slightly different dimensions. WeMos D1 Mini ESP8266 ESP-12F WIFI HLK-LD2410 LD2410 24G FMCW 24GHz *12/26 - updated…
This model is compatible with the lego system.
In this case fits only a LD2410C, see the pictures. This is meant for bluetooth use case. So if you are integrating this sensor over bluetooth to Home Assistant or any other Home Automation Software, this Case fits perfectly.
Eclosure for WX-2412 24V power supply board. It was designed with 3D printing mentality. No supports needed. CAD files included. Features: -The 40mm air intake fan -XT60 connector for DC output -IEC320 C14 socket for AC input -Easy…
Sensor housing for the esp32 super mini c3. I printed on PLA and the lid is a snap in design (though feel free to modify to use screw posts). The ESP sits very snuggly in the case - so you'll want good tollerances.
This is a replacement shelf for a Frigidaire 241691311 refrigerator. It goes on the upper section of the door. The shelves that come with this refrigerator are an extremely poor design, and break almost immediately if you put any weight…
Snug fit printed flat on a Prusa Mini on 0.2mm speed profile PETG - 100% infill about 30-35min print time. EDIT: I have added a tall version of the Cable Management. I have not tested it, print at own risk.
WAGO 221-2411 clip, screwable (M3, 10mm distance in both directions), connectors (not to) easy to push out and push in, 1 to 8 connectors, created with onshape . No supports needed, printed with PLA
Material: PETG Material : PETG Resolution : 0.15mm Infill : 100% Printed with brim for better adhesion. Place M3 nut in holder. Cut plate according to scheme.
This design uses a standard NEMA17 stepper motor as a 4th axis for a standard CNC 2418/3018. A custom deisgned mandrel serves to hold a ring in place while a standard 30 degree V-engraving bit is used to engrave soft metals such as brass.…
Case to house LD2410 and D1 Mini. Printed in PLA, no supports.
This case is based off of Digital Juice's. This update fits the LD2410 and ESP32 C3 super mini from Aliexpress.
A finder foot for the Svbony SV241 Powerbox, allowing you to attached to a finder shoe on your telescope. I used two M4 10mm button head screws to attach to the Powerbox.
I Modified the project to be able to store a LD2410C instead of the temp sensor. Also i opened part of the top case for the light sensor, as the measurements were pretty low. There is plenity of space for the cables, so you should be able…
Hi, a friend was in need to connect some wires for a project of his. I found the model of ‘Jemand/Joschas’ and it fitted his needs. We just needed a version for 6 wago 221-2411 clips in one piece and a base size of 52 mm x 39 mm for…
This Radar Presence Sensor is easy to build and pretty cheap considering its performance. The firmware uses ESPHome . The sensor uses the universal ball-joint design so it can be oriented for accurate detection. I provide a skadis mount…
Junction box for wago 221 2411. The numbers of connector can be set by changing the value of user parameter [long_connectorn_number]. The hole in the bolt can be changed up to 7mm by modifying the value of user parameter…
Yep. It holds an ath20 board, a panasonic PIR, an mmwave radar, and an esp32 of the 38-pin flavor.
This model is compatible with the lego system.
I wanted a case for the LD2410C that i could just plug in a 5V PSU and use it over bluetooth The case allow for the sensor to fit with the pins, but i also uploaded a slim version without the pins When inserting the sensor on the top do…
Verbindungsgehäuse für Leitungen bis zu 6mm Durchmesser. Der Deckel wird mit dem Gehäuse Zusammengesteckt und die Leitungen können mit Kabelbindern fixiert werden.
With three and seven connection options
A wall mount radar presence sensor with a LD2410C that gets directly attached to the Wemos D1 Mini Esp32. EspHome and Home Assistant recommended. Fitting yaml is provided as txt (restriction from printables). BOM: D1 mini ESP32 with…
WORK in progress Hello, I designed a Case for the mmWaveRadar-sensor HLK-LD2410C-P from Hilink. It's a first version, more a tryout. The sensor is the version with 2.54mm pinout. It's the “friendly” one. You can better solder it, as the…
Rectanglar case with snap fit lid and visible sensors
I have designed and printed these cases for personal use in PETG. It can be panned and tilted and has a cutout for the USB cable. Software in my case is ESPHome connected to Home Assistant
changed internal box to support d1 mini esp32 added a clip to hold down the d1 mini esp32 added a home assistant logo
My students and I are developing gridfinity shadow trays to organize the tools. Some fit better than others and most of them are setup for a 1in tool pocket depth. There will be more posted soon. Here is a tray for the M12 3/8in Right…
Printed with PLA+ 20% Infill Supports preferred, based on printer
Simple, secure, toolless Wago DIN mount clip using Bryan's original design. Install wago from the side with the latch side centered then press the opposite side down and rotate into place. It is a tight fit making the wago very secure…
This model is compatible with the lego system.
These are a replacement door bins for LG LSC27925, LSC27937ST fridges, replacing LG part 241H / MAN61844401 / AAP72911202. I printed this on my Sovol SV06 and it took up nearly the entire 220mm x 220mm print bed, so I think you'll need a…
This model is compatible with the lego system.
Gridfinity compliant, low-profile tray/holder for the IWISS IWS-2820M and the IWS-2412M open barrel terminal crimping tool. I did not completely design it from scratch. I used schenklooza 's excellent Gridfinity Parametric Blank bin as a…
This model is compatible with the lego system.
The OWON benchtop meters XDM1041 and XDM1241 are both nice units for benchtop work but could use some gridfinity lovin' so here we are. This model should fit the meter tightly such that it won't just lift out of place. To insert, start…
I made this model from physical measurements I took. It is as accurate as my harbor freight digital calipers are. The model is based on FA2-16/1WEK but I have Z2S2416 also, and the only difference is that the heatsink covers more area and…
Box for ESP32-S2 equipped with an LD2410C sensor. Printed with PLA, at 0.4mm, no supports. DIY Project: https://www.nlion.fr/nicolas-lion-informatique-ancenis/2024/02/25/ld2410c/ Category: DIY
Fits the wago connectors listed below https://www.wago.com/gb/installation-terminal-blocks-and-connectors/inline-splicing-connector-with-levers/p/221-2411
I bought Some Dell monitors and used them for some time. Eventually I got a mount, so I could have a 4 monitor setup. These didn't have VESA mounts, so I was looking at replacing all my monitors. I decided to model an adapter to fit on my…
Please comment, rate, and post a make! A simple case for using an LD2410C radar sensors with an ESP32 C3 Mini that can be mounted to the HSW. I've included a little spacer that can be slid over the pins of the LD2410C to help with…
Into 1:72 scale model radio control ships. Usually we buy 1:72 scale fibreglass hulls from somewhere like APS Models and then scratch build the rest of the ship ourselves (e.g. propellers, motors, servos, radios, deck, superstructure)…
To print the cover with the logo in two colors change the filament to a different color at layer 4 and 6.
A series of mounting brackets for a LD2410 motion detector, one for the LD2410B and two for the LD2410C for the LD2410B and LD2410C there is a wall mount, i use it to mount te sensor flush against the wall to person detect on the other…
Original project: https://www.printables.com/es/model/189821-d1mini-sensor-case-dht22-bh1750 I Modified the project to be able to store a LD2410C instead of the temp sensor. Also i opened part of the top case for the light sensor, as the…
Slight remix of the original model by Prashant Sinha . For instructions please see the original model . The only differences are that this model is adapted to use M2 screws, the original model requires M2.5 which I did not have available.…
A try to keep labels aligned, help them from being pushed off the desk. Designed to work with the Phomemo 241BT and similar.
lego 2877 71752 98283 15533 30136 30137 20310 2412
Holder for the X-axis cable wrapping; The only one moving one that in the kit stays loose. Recommend to print in ABS and use 2 layer raft
This model is compatible with the lego system.
This model is compatible with the lego system.
Gehäuse mit Deckel für vier Verbinder 221-2411. Es werden noch zwei M16 Kabelverschraubungen benötigt, sowie 4 Senkkopfschrauen 3x8mm
The OWON XDM1241, being a budget bench multimeter, is quite a neat little unit for the hobbyist. Its small form factor certainly is a plus if you don't have a lot of bench space available. The downside of it being such a compact and light…
This model is compatible with the lego system.
I remixed a Mele miniPC holder to add a support bracket for the new SVBony SV241 mini power box and USB hub. The holder can be mounted on any Vixen/Losmandy/flat bar with 2 M6 holes spaced 20 mm. The Mele miniPC is inserted in the slots…
Thanks to @Creo2005_265049 for providing the base with the f3d file. I changed it to fit Thetford N4241 / N4000 caravan fridge. To illustrate the dfference, on the first pic this part is clipped into the N4241 shelf, the original from…
Same size as the original, just added a mounting-option and changes vent holes.
I designed a small enclosure for the HLK-LD2410B-P mmWave sensor bord for use in Home Assistant. More details can be found at https://github.com/jonnybergdahl/Sensor_LD2410B . I have included the Fusion 360 file so you can remix it as…
Case for ESP32 and LD2410C MMwave sensor. Fits LD2410C and ESP32 with dupont connectors. Use double sided tape or hotglue to mount ESP32. Use M3 25mm for base and lid x2 M3 16mm for arm. x3
Hi there, Sharing my little bathroom mirror project, specifically the part with a housing for LD2410 mmWave sensor which then connects to a d1mini controller with ESPHome for automated bathroom mirror ledstrip control. Features easy…
Enclosure for a DF Robot Beetle ESP32-C6 and a LD2410C. The enclosure is a tight fit for the C6 but it fits nicely. You may need to push the USBC male connector from the C6 into the enclosure's USB hole from the outside once or twice at…
Snug fit printed flat on a Prusa Mini on 0.2mm speed profile PETG - 100% infill about 60-70min print time. EDIT: I have added a tall version of the Cable Management. I have not tested it, print at own risk.
Rectanglar case with snap fit lid and visible sensors
