294 modeli
This file is a more rigid servo arm for the Rancher. The Rancher itself is NOT part of this assembly! If you want to print the Rancher, you will need files from third party as well. Files can be found at 3dsets.com. The Rancher has 4x4…
Wydruk około 0,22 €–0,27 € nettoWstępna wycena jednego wariantu
This print is a continuation of my design from last year . The actual plow is reusable from one to the other, I just fixed a minor issue where it was accidentally slightly angled up on the right side and added the height adjustable…
Wydruk około 2,27 €–2,77 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Before installation can be equipped LED in the headlights: I printed the models "Front light - left.stl" and "Front light - right.stl" with holes 5 mm (corresponds to the size of my LEDs). I respect the model license (model purchased on…
Wydruk około 0,11 €–0,14 € nettoWstępna wycena jednego wariantu
I realised that the printed ball joints for my Bamboo Toyota FJ40 are too big. However, I have installed them all. Now I need to remove them and install a smaller - scaled ones. This is the tool to uninstall them with vice or hammer. No…
Wydruk około 0,21 €–0,25 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Remove supports from fully cooled print
Wydruk około 0,39 €–0,48 € nettoWstępna wycena jednego wariantu
So I made the trailer hitch for model 13 - winch truck from 3DSets. You can use my MINI/MK3 plates or provided STL’s. Just keep in mind, that the "Model 13_Trailer hitch_01 STL doesn’t have holes in the whole distance so you need to add…
Wydruk około 0,85 €–1,03 € nettoWstępna wycena jednego wariantu
It's a little different than the original of the mini truck and tanker trailer . If you look at the photo's it is easy. use m3 bolts same as the original parts
Wydruk około 3,12 €–3,82 € nettoWstępna wycena jednego wariantu
So I made the beadlock rings for the 3DSets rancher wheels to prevent tires from slipping of the rim. In addition, you can add 70g weights to each of the ring to lower the center of gravity. To add the extra weight, I used these Pb…
Wydruk około 1,23 €–1,51 € nettoWstępna wycena jednego wariantu
This is the hood with a scoop, allowing extra clearance for additional motor cooling of your winch truck from 3DSets. You should print the hood with extra supports. You can also change the density of a mesh in prusaslicer. Honestly, I am…
Wydruk około 0,09 €–0,11 € nettoWstępna wycena jednego wariantu
Trailer addon for Landy Mini by 3D Sets. It is just a little remix of by markberk from Thingiverse. https://www.thingiverse.com/thing:4656335
A trailer for the Landy mini from 3Dsets.com: https://www.prusaprinters.org/prints/41264-landy-mini-by-3d-sets Remix of the smaller trailer. For me it was too small and it was too high compared to the car. So I remixed it. Also fixed the…
Male driver is based off of: https://grabcad.com/library/the-male-figure-carl Female is based off of: https://grabcad.com/library/mulher-sentada-seated-woman-human-person-1 Scaled and modified to fit as a driver and passenger in the…
Stand for 3Dsets Jeep Rancher 4x4 & Landy 4x4 & Bamboo 10/2/2020 - addes v2 upper part for much more stability 13/2/2020 - added v2 middle and bottom part, can now be screwed together 2/10/2023 - adde middle R-20 part for compatibility…
This is a remix: https://www.thingiverse.com/thing:4394842 Mud guard for the front and back of the 3DSets Landy. Logo land rover
15mm is hole spacing 3.10. 2020 - servo arm 15mm 3.10. 2020 - added servo arm 15mm + nut hole 4.10. 2020 - added 20mm version 4.10. 2020 - tooth optimization Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No…
Angry eyes for Rancher jeep from 3dsets.com To be glued on top of the default grill Print instructions No tested yet, let me know how it prints and fits
Modified front panel so that the angry eyes grill fits over it. Both parts easy to print flat on the printer. Made holes to replace the two upper 3 x 10 mm screws with 3 x 12 mm screws to secure together the angry eyes mask, front panel…
Designed for GMADE MT-1902, but will probably fit variety of other tires. Rim diameter is 49mm and width is 30mm (+4mm with beadlocks installed). Hardware: 1x SHCS M3x16-25 through the center 21x SHCS M2x6-10 for beadlock 3x SHCS M2x6 for…
A bullbar for the Landy mini from 3Dsets.com: https://www.prusaprinters.org/prints/41264-landy-mini-by-3d-sets No supports needed, they are pre-modeled in there in the spirit of the Landy Mini model. Just remove them. Print Settings…
My first #printedtrophy attmept showed me, that the original foam in 1:10 tires is way too soft for a van full of spare parts and batteries. So i started experimenting. This is my 9th iteration of FLEX inserts, tested in Fiberlogy…
Remix of original model: https://grabcad.com/library/the-male-figure-carl Changes on model fits to seat of 3Dsets Model 8 Buggster his right leg is shorter, fits to pedals right hand on other position brand new ears less belly fat more…
Solid layers - Top / Bottom (0 layers) Infill density: 30% Infill type: Honeycomb Perimeters: 2
This is open differential for Jeep Rancher from 3dsets. I test it on version Wagon, but should be possible to mount it also on other versions. I created it this open diferencial, because I'm using my Rancher in house on vinyl floor and…
This is a Front Bumper for a 1:8 scale Warn Winch for the 3DSets Landrover Defender. Included are two versions. One with holes to mount tow hooks, and one without the holes. Mount the parts as shown on the pictures. You need the Original…
This is a mod that allows you to use this roof rack: https://www.3dsets.com/product/roof-rack-accessory-for-model-4/ on the much larger Landy 4x4 Wagon. You will need at least a 300x300 print plate to print the rack and side rails but I'm…
I found some files for the jeep rancher angry eyes but they were separate and required super gluing or screwing on. I had issues printing these and getting it to look clean due to supports being needed so I combined the two models and…
This is a dashboard for 3DSets Model 7 Buggy designed for a double colour change at layer height. Open the 3MF in PrusaSlicer and press Slice now to see the layers the colours are changed at. Print at 0.15 mm layer height using PLA. Also…
Stand for 3dsets.com Landy 4x4 Wagon modified upper part for better vehicle balance and better fit slightly wider stand footprint for improved stability Print instructions 0,3 mm layer height, 3 perimeters, 15 % gyroid infill.
This grille is for the 3DSets Model 14 “MAX Team Van” aka the “A-Team Van”. It will replace the Grill labelled “MAX” with the “GMC"-labelled version that you need for the A-Team Van (or any othe GMC Express Van).
Collection of mud flaps for the front and back of the 3DSets Landy. Overview Logo 4x4 Mountain. LandR. Logo. **** Printed with PLA and 0.25 nozzle, color change at 0.65.
opona do modelu rescuer 3dsets
The parts of this mod are a replacement for the “Roof1”-part from 3DSets in case you want to add a sun roof to the Model 14 / MAX-Team / A-Team / GMC Vandura Van. You will need an additional piece of clear plactic sheet for the glass of…
As I am building the model 7 Buggy from 3Dsets.com, I was missing a hood strut to keep the hood open. This can be handy when working on the receiver, which on this model is located under the hood, or just to keep the hood open when on…
I made this blank licence plate as a basis for guys interested in making their own. Step file is included although not sure if I exported it using right preferences.
I wanted the same bumpers as my Jeep Wrangler, so I re-diesigned the originals from 3DSets. I also customized the winch, winch hawse, a stronger winch drum and the D-Rings. Printed with Overture Matte PLA with 80% infill and 0,10 layer.…
Print settings 0.2layer Quality profile, printed with PLA. Original bottom part doesn't fits on Prusa Mini printing plate. Model is bigger as maximal size of plate. So, it was little bit redesigned for printing on Prusa Mini. Assembly…
3dsets.com Landy 4x4 and Landy 4x4 Wagon modification for LED lights Wheelhouses - modified original mesh, added 24mm holes for lights Rings - to be used instead of default printed lights, push the LED light into it Print instructions…
INFO Scaled down the original model to fit the Landy Mini, more items like air intake and original model for full size 3DSets Land Rover in the link below. Credit to original creator: https://www.thingiverse.com/thing:4270060 PRINT…
!!!!! Please read before building. This is a metal geared axle and transmission conversion for the popular 3Dsets Landy, Rancher and Bamboo. Axle ratios are 3:1 to 4:1 the original 3Dsets axles are only 1.8:1. The axles and transmission…
grill gmc for model 14 3dsets
Original file had to much play in the 12mm tire and around the 8mm axel. The updated file fits perfectly snug on the model 7 buggy. Printed with PLA .15mm with a brim.
This is a towbar for the fantastic @3dsets Landy model 3, 4 and 5. It fits on the rear bumper of the Landy. Use a 1,8mm drill to enlarge 2 of the small premarked holes. Hardware needed: 4x m2x6 1x m2x10 I used the same kind of screws used…
This is a more realistic and functional towbar and trailer coupling for the Landy Mini by 3Dsets.com and the different trailers. The towbar is a remix of RearBumperForTowbar.stl by Matthijs2101 . Unfortunately, this design requires…
My creation of a roof rack, to mount on a 3Dsets Landy Mini: https://www.prusaprinters.org/prints/41264-landy-mini-by-3dsets Print instructions Category: Toys & Games Summary My creation of a roof rack, to mount on a 3Dsets Landy Mini:…
Collection of different license plates for the landy model from 3DSets. Overview Cal01 - 1 Color change. BadNews - 4 Color changes. BLOB Galactic Empire - 1 Color change (BLOB = Big Lump on Board).
Loved @daver18qc's Hi-lift jack https://www.thingiverse.com/thing:3513415 but needed a way to mount it to my Landy wagon from @3DSets. I made two. One is the "full" mount that replaces one of the hinges on your rear door and holds the…
Koło 2.4 beadlock MAX TEAM
can be printed without supports in PLA and be connected on the pins with glue
Had an issue with my Landy Wagon where my links were flexing when crawling. Sometimes this caused the axle to shift and move the tires into the wheel well causing issues and binding. This is a tool-less, snap-on, solution. These sliders,…
pasek do modelu 14 3dsets HDT 144-3M-06 drukować z tpu
Needed a Headlight lens and headlight bowl (modified) with a 5mm hole for leds the 3dSets Landy build. Print with the dome facing up and use supports. You need a small CA glue dab to attach it to the inner headlight housing.
Na fixaci dílu používám trochu lepidla, ale není to nutné.
GT2 Belt Gearbox for Landy/Rancher/Bamboo 3DSets models. Use it with my Metal transmission, gears and axles mod This gearbox has a ratio of 4:1. Paired with the AR44 33/8T gears, it is the same overall ratio as original 3DSets model. You…
Print Settings Printer: Prusa i3 MK3S Rafts: No Supports: No Resolution: .15 Infill: 15% Others: 9x screws M2x6
Steering Servo Shim If using on 3Dsets Sandy or Bug you might want to upgrade the steering horn too. See this upgrade. https://www.printables.com/model/321649-3dsets-bug-steering-fix
Front headlight lens for Model 7 Buggy from 3DSets
This model is now depreciated, please use the new one . Are you tired of clearing your driveway by hand? Is it too small to justify a snowblower or other full scale device? Well now, it can take you twice as long, using your RC. This…
2 color printable Model_17_Sakura_240 3dsets
Model is designed from scratch, based on Tube Doorsteps for Model 1 & 2 Required screws for assembly: 8x M3x10 2x M3x8 (rear screws) Intended to look good with accessory Tube Fender Flares for Model 1, 2, 6 , but it will fit with the…
A different bonnet for the Landy Mini, pimp your landy. Print at whatever works best for you.
Spare wheel carrier for 3dsets landy. Printed in Prusament PLA with 0.25 mm nozzle. -- Note on the rear bumper and on the right rear fender, holes must be 1.8 mm. Screws needed: 8x M2x6 2x M2x10
This is another make of the 3Dset's Belt drive motor adapter. I found some makes already available, but the mount hole spacing on the motor I used (FlashHobby D3630 EVO “Turbo”) did not fit the holes in the other makes, so I made a new…
Modular segmented back light for Rancher from www.3Dsets.com
New light + cover. You print the cover from transparent filament. I used Nebula natural. Spectrum alu silk was used for the light
Rear tire Buggy by 3dsets. I used filament TPE88 from Filament PM. Infill: On the sidewalls of the tire, I've used the modifier and infil straight line 8% Tread use infil 0% Supports: No Rafts: No Resolution: 0,2mm Perimeter: 2
Servo arm remixed from https://www.thingiverse.com/thing:4834035 to fit different part supplied with servo. Also little bit shorter to be sure that steering rods won't touch front axle parts and also mounting holes for steering rods are…
This is a spacer used on models from 3DSets.com (both Landy and Rancher) to move the wheels and tires outward. Making a wider stance and moving the wheels away from the shocks. Giving you more shock options, more potential for…
I modded the lights for the Landy to fit 3 and 5mm LEDs that come in most RC light kits on aliexpress.
This model allows using bigger 3S2P custom battery packs made from 18650 cells in the 3DSets Bamboo (Model 13 - Winch Truck), model available on their site: https://3dsets.com/product/model-13-bamboo-4x4-winch-truck/ Side fuel pipes are…
I recommend to print it with 100% infill
FRONT LIGHTS: I used silver filament for the light and black for the shape. Transparent filament for the turn signals. Then I cutted 2 circular shapes from the plexiglass used for the glasses of the model. BACK LIGHTS: I used black…
The real stuff For my Bamboo4x4 I wanted a fully functional roll cage just like the 1:1. This is it. The cage fits the Bamboo4x4 Model 9 & 10:…
I had problem with original 3D printed servo arm slipping from the servo, that's why I made this adapter for the aluminium servo arm. You will need aluminium servo arm 25T, see attached image. Supports are already built in, don't forget…
Needed more cooling for longer drives. I actually saw somebody post something similar but using a hacked stock radiator. Figured, there's a better way! Enjoy and Post your makes! The fans I used:…
Modifications to 3DSets Landy Wagon (and other 3DSets models) to go to metal transmission from gearbox to wheel, using Thumper axles Use in combination with Gearbox with 3D Printed pulley and Metal output GT2/Metal pulleys gearbox UPDATE…
Made to fit the Bamboo Land cruiser. May fit others. Color change G Code below
To make it waterproof. I recommend to add silicone (as example Done Deal) on all adjacent surfaces, and to the wires under the small cap. Use it on your own risk! PS: parts are very stiff to connect. Its important for better waterproof…
Although I was okay with how the original axhaust looked, it broke when I rolled the car (flipped it at it's maiden drive outside). So I designed this alternative exhaust. It has a classic and robust look and it fits withing the engine…
Created a Towbar and a trailer for a 3Dsets landy( https://www.prusaprinters.org/prints/41264-landy-mini-by-3dsets ) Towbar is the same as for playmobil car. A playmobil boat fits(clips on) on the trailer. Print instructions Category:…
Just simple custom rim for 3Dsets RC cars. Recommended print resolution is 0.15, cut in half (Z 13.75 best). Print instructions Recommended print resolution is 0.15, cut in half (Z 13.75 best).
Front headlight lens for Model11 Sandy from 3DSets
3Dsets Skippy Boats ESC switch holder for QuicRun WP 16BL30 req. 3x M2x6 socked head screw 10.11. 2023 - added holder WP 16BL120
Some friend ask me for helping to more durable of often broken original parts. I completely new designed the engine block. I transfered most of power trans pieces to steel or aluminium. Durability is more, more better. Constructed for…
Simple Frontlight Glass for 3DSets Bamboo Rc Car. Depending on your printer it should snap in place. Might need a superglue. Use concentric top & bottom layers for more realistic look!
My tire kept slipping on my rim with my Rancher wheels and Super Swamper tires. These rings help you "lock" the tire in place. There is also an option to use M3 nuts as weights — 48 per lock ring. Enjoy and post your makes! If you found…
3Dsets Jeep Rancher 4x4 Light with hole for 5mm led Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15 Infill: 25% Filament: Inland PLA Black/White Category: R/C Vehicles
Work in progress changed to READY TO MAKE! - 5.11.2020 Print, assemble, ENJOY Share your feelings down bellow in comments :) If you like it, you can support me with cup of coffee…
The original by @hennery was a little funky to slice and print and I needed the inside cutout to be a bit deeper to fit my build. Here is the fix. Video on YouTube.com/3dprintsos Enjoy. Category: R/C Vehicles
This is the headlight from the 3Dsets models with a hole in it for a LED light. It works really well with this lens: https://www.printables.com/model/237490-headlight-lens-cover-for-the-3d-sets-landy/comments/454368# Print in Silver Silk…
Ich habe für mein 3DSets Model 6 ein paar neue Türen entworfen. Die Fronttüren davon sollten auch bei Model 1 & 2 funktionieren. Damit der Spiegel besser passt habe ich auch die Original Spiegelhalterung angepasst.
Modified Africa Trophy front bumper with larger winch mount to fit an RC4WD 1/8 Warn Zeon Winch.
Here are some modifications I put together to widen the stance of the Wheel B set for the 3D Sets Buggy. Spacer: Makes the front wheels a bit wider and grips the foam tire core for less lateral tire movement. The goal was to stop the…
If you are like me you love the 3dsets Bug but hate the easy to break steering. There are other fixes here on the site and I have tried them. Here is one that works using parts that you likely already have. The steering servos that I buy…
Bull bar add-on for 3Dsets model 20 & 21 (Mogster). Printing The bull bar must be printed with support. I printed it in the orientation shown in the picture. Mounting The bull bar is attached to the bumper using 4 M2×6 screws. Either…
I created these headlight lenses for the model 7 buggy. I also installed LED lights in and so these will fit with LEDs. I created 2 designs, one flat backed and one concaved. I was able to use the flat ones with my LEDs, but YMMV. Enjoy!…
Rear wheelhouses for the Model 5 Landy 4x4 Wagon that has holes for led lights This has the openings for all the rear lights of the Landy model Print on .20 resolution in black PLA. No supports needed as per original design by 3Dsets
3Dsets Landy 4x4 Wagon ESC switch holder for QuicRun WP 16BL30
This is a side grille for Model 6 Rancher from 3DSets . Use 4 Screws M2x8 and screw it into the side panel.
Remix of this Model7 Buggy servo arm adapter to work better with the servo horns I purchased on Amazon : https://www.amazon.com/dp/B07D56FVK5. Changes: Holes for mounting the servo arm increased to 3mm Center hole enlarged to allow…
Issue at first run: tire pops out of the rim. I create this simple cylinder, in order to put it inside tire and lock it into the wheel when screwing the rim. (It press the tire between internal beadlock and rim). Not miraculous (still…
