142 modeli
Prusa released the printable parts for MK3s+ and the fan shroud is much better than the stock one of the Mk3s, so, for everyone who don't want to fully upgrade from Mk3s to Mk3s+ but still would like better cooling, I cut the second…
V1 - untested - 2x3 and 1x2 Gridfinity Baseplates adapted to Multiboard system - untested - tested: 2x4 Printed in clear resin it fit too loosely into the Multiboard octagon tile, but with a bit of glue it now holds a 600g bluetooth…
V2 is available now. As requested, we've lowered the handle (consequently, the siphon), so the draining action should now start at about 2/3 of the cup. In the original file, the mug would have to be almost full before it started…
Modified V3 Shell to properly fit the Foxeer Wildfire Analog Module
Contributo al sistema "Retractable_Probe_Dock for Klicky Probe e Quickdraw Probe" per Voron di "Tronfu" riadattato alla VzBot. Più che contributo, e un restyle estetico al modello di Eduardo Sousa ma modificando il sistema di regolazione…
STL model units are mm
Obs: This mount was primarily designed to be used with my tilt, both for desk and wall mounting, which can be found at this link: https://www.printables.com/model/1073632-reolink-e1-mount-magnet-wall-and-table-mount I have Reolink…
A printed offset block lamp shade using the Bambu Lamp Kit 001 Base and Puck Led lamp. This shade uses a square base to adttach to the bambu Led Lamp 001 circular base. Lamp w/Base: 215 mm by 80 mm wide No supports required. The puck led…
This is based on Adafruits model. I adapted this to use the 608zz bearing, and printed a base
UPDATES: Added version with mounting screw holes countersink so knob does not collide with screw head for those using full sized screw heads. This focuser is based on the Crayford design, where a smooth pinion is rolled along a smooth…
Link to the chain To install it, you will need: 1) Screw M3x10 ISO7379 (10mm is the size of the smooth part! To this length, 6mm threaded parts are added, a total of 16mm!) Or screw the limiter onto a regular M3x16, the file is available…
Remix Description: Added small ridges on bearing pin to create a tighter fit with ø8mm bearings. This ensures the bearing actually rolls on its internal ball bearings, rather than just freely spin around the pin. Also re-oriented the STL…
I didn't like the original plate as it is a little bit to big relative to the vase and it could not hold any water being to shallow so I made a smaller design that has higher walls.
A honeycomb pattern lamp shade adapted to use use Bambu Lab Lamp Kit 001 base Shade with base: 190 mm height x 85 Width No supports required. The puck led used here: (The example used a 5W, 2700K, Warm White)…
I've adapted this model: https://www.thingiverse.com/thing:3369946 Using Meshmixer and a reasonable amount of patience (lol). Print instructions The design was meant to be printed using the MMU2S from Prusa Research. High resolution is…
To lower the angle and reduce the tension on the spool, I've raised the length of the slider aligner pivot by 10 mm. To reduce the friction I use a Capricorn's PTFE tube on the slider aligner arm. I've adapted the tension arm to use a…
Remix of Stigern's great model, with screw holes adapted for 2.5mm Ø countersunk screws (2.5mm x 20mm screws used in my case, EAN: 4053199302444 )
This is a bracket that mounts on any standard 3030 T-slot rail, with a T-nut and a M5 bolt in the back. You can attach a common Arca-Swiss adapter plate to the front using a ¼-20 socket head screw with a washer. I designed this because I…
Its a heavily modified version of the ingenious design from Vez3D, exclusively for the VCore3 with the stock MGN12C rail
I liked the height, the design and the adjustability and just didn't have the right screws at hand. So I adjusted the model for the M3s that I had. Because those didn't fixate the sights in the notches of the rail due to the smaller…
I had a lot of spare parts after converting my Ender 3 to a Switchwire, including a linear rail that was 20mm too long for the orignal Stealth Press. So I decided to just adapt the existing files to my spare 2020 aluminum extrusion that…
I loved HD_Creator's vise but I found 6mm bolts and nuts very hard to find in the USA. I revised it slightly to allow the use of common 1/4in-20 hardware which is available everywhere here. I used TinkerCad to enlarge the hex shape in the…
Voron Legacy tensioners on the drives are flawed and I would like to have a bit more control on the front. Voron Trident front tensioners are quite well engineered. This is an adaptation of those tensioners to work with the Voron Legacy.…
Airbrush HexDesign Stand adapted to fit more airbrushes including those with air valves
Adapted Wiper Clip for Subaru Impreza to Rain-X printed in asa
I have taken a wonderful Raspberry Pi 3 case from Squirrelbrain and adjusted the design for use of ruthex thread insert instead of screwing bolts directly into plastic. For mounting of Pi plate the M2 thread inserts are used. All the of…
I didn't find an existing way to adapt ZeroClick on my MiniSteahburner so I finally decided to redesign it by my own. I chose to fix it with 2 screws (M2 8mm is fine) and 2 M2 brass inserts (M2 3mm). You have to reprint your toolhead. I…
Introduction: SteveT did a great job collating parts and doing a writeup of the assembly, I just didn't pay close attention when buying parts and ordered the wrong bins. These were branded “Kichly” rather than “Skroam”; the biggest…
I needed a spool holder that fit small diameter filament spools from local brands. Uses same pin and roller as the original. Removed the logo. I printed it in petg, using it with printed bearings, decently tight fit on the printer, no…
NG extruder fan shroud 5015 adapted since I like to use 0.6 nozzle I also made a volcano adaption for this fan shroud with 5015 blower
Adapted design for assembly without together screw. Screws replaced with plastic snap-in latches. Original thing: https://www.thingiverse.com/thing:922740 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No…
This is a set of adapted V2 BeltClamps if you use the ChaoticLabs Carbon Fiber Bracket Kit together with TorxFighter Zero offset Clamped GE5C Mount for Voron 2.4 + Beefy Front Idler The V2 BeltClamp design is used where possible and the…
I purchased two Hockey CCM Helmets in a end-off-life offer, but actually, the Full Face Visors I have are from Bauer. The holes for the clips in the CCM helmet are 11mm wider than in Bauer helmet and I designed this clip variant to avoid…
I didn't like the design of the Bondtech IR filament sensor adapter for the Mk2/s upgrade extruder ( https://github.com/BondtechAB/Bondtech_Prusa_i3/tree/master/CAD-Files/MK3s%20Sensor%20Add-On ), so I made my own. this one flips the…
This is just a remix with adjusted measurements for the playmat of The Witcher Old World, which is pretty large. You need to print all in vase mode. I printed all on PETG, but PLA will work just fine. Need to print: 1 x cap 1 x Base 3 x…
Remixed the main button so it can be installed on a Skywatcher Crayford focus button. If you want really smooth operation, check out the anti-wiggle needle mod here:…
I have been using these very reliable spoolholders by ea69 for a few years now and always wanted to have one for 2kg Prusa spools. I used the step file and made the stand and the threaded shaft 40 mm wider. I did not know the parameters…
Basically, I cut the handle off the original and attached it to an existing Elucidator model so I could use it.
I've printed all the parts from PETG (230°C/70°C), without support, layer 0.3, cubic infill 30%, 4 walls, 4 top/bottom layers.
Added two pegs to the original design to mount it on a multiboard.
DF54 has two holes, against 1 in DF64, I remixed the original model. The two holes were fixed a little below the one in the version for DF64 so that the dosing cup can get closer to the chute. Publishing here for someone to print and test…
Thanks to "Triple G Workshop" for the great shelf stopper. Instead of having to create one myself, I was able to save a lot of time by modifying the existing model. By adapting it to a wire spacing of 30 mm in width and 18.5 cm in height,…
All other parts which used to require drop in nuts now use heatset inserts! they are M4mm knurled inserts 8mm long. changed the motor mount to now be longer, aswell as the motor cover, to fit the 1:27 stepper gearbox mod also posted in…
Remixes the main knob so it can be slip-fitted on a skywatcher ST80 stock focuser knob. If you want truly smooth operation , see the anti-wiggle needle mod here :…
This is my first 3d project upload. I remixed a hot wheels launcher to make an adapted bocce launcher. This was a way to make an accessible bocce launcher for use during adapted physical education classes. This is the 4th or th…
I like Tomasz' original Version for the Prusa I3 MK3, but I own a smaller Prusa Mini+, so I changed some things. When I started I wasn't quite familiar with FreeCAD and Prusa-Slicer, so I had some learnings and of course I would make it…
I modified the original mounting bracket model from Sovol for the Sv06 to allow the mount of the BTT M5P mcu box created by Raziel. I took the stock bracket and extended it 13mm to clear the top of the box. I could not put the mounting…
Add dual 4010 fans to a stock Prusa Mini or SliceEngineering Copperhead. Uses Annex Engineering K3 4010 fan ducts, at original angles and spacing. Suggested 5V Fans: BFB0405HHA-A (2 wire, no Tach) or BFB0405HHA-AF00 (3 wire, w/ Tach) If…
A pot lid rack that prints in lil sections - adapted original model to make it a bit nicer by having clean start and end parts. Original model: https://www.printables.com/model/1178526-chaining-pot-lid-rack. Thanks to…
It no longer intercepts with the belt.
This MOD replaces the stock 4010 fan with a 5015 layer fan,a 3010 for heatsink cooling and an optimized fan duct. 5015 Fan improves air flow and air volume. It's adjustable in height. 3010 fan, replaces the crappy and noisy one that needs…
This is a remix of the Voron M4 extruder for Ender 3 V2, see https://vorondesign.com/voron_m4 and https://www.thingiverse.com/thing:4901100 I publish only the modified midsection, which I have optimized for extruding soft TPU, i.e.,…
The goal of this design is to utilize my spare creality k1 extruder to my other 3d printer (specifically my CR-10 V2) and gain learning experience making 3D designs Please refer to the original extruder design for the inner motion…
Add dual 4010 fans to a Prusa Mini with a REVO hotend. Uses Annex Engineering K3 4010 fan ducts, at original angles and spacing. Suggested 5V Fans: BFB0405HHA-A (2 wire, no Tach) or BFB0405HHA-AF00 (3 wire, w/ Tach) If you want the fans…
This is a slight modification in the LED Light Bar to fit a 9x17.8mm u-profile. Para os Brasileiros que estão tentando montar o LED Light Bar, esta é uma versão modificada que encaixa perfeitamente no seguinte perfil de alumínio:…
I designed this knife due to my own limitations while handling ordinary cutlery. The body and 2 grips can be pressfitted together depending on handedness. I used ABS and had no issues with stability so far, given that the visible part of…
I had 2 EMO button but only 1 module to cut the main voltage. To re-purpose the 2nd EMO, I've made this box to adapt a small 6mm tact switch (pushbutton). The height is adapted to screws I had in stock. The hole is large enough for a 2…
The goal of this design is to utilize my spare creality k1 extruder to my other 3d printer (specifically my CR-10 V2) and gain learning experience making 3D designs I have provided my step file in hopes of other people adapting it into…
With four short little wire parts you can make the torpedo covers work fine and have the morrigan class with two torpedo tubes. I even fixed the part to connect parts xxx_-_morrigan10 and xxx_-_morrigan15 better but still holding really…
Can Hand Holder for SUP-Board, Kajak… https://www.printables.com/model/980526-stand-up-paddleboard-05-l-dosen-07-l-thermoskannen
Add supports under indicator Print ring separately (100% scale) PETG 0.2mm, 20% grid infill, nozzle 0.4
As for @JeremyKREBS_559468's design, you may need to remove the carboard organizer from the box, fold the carboard around the printed organizer before reinserting it into the box. However, the fit could be better with thinner sleeves or…
Sasha D's Crayford-style focuser for the Hadley telescope is excellent! I highly, highly recommend it. Focus adjustments are MUCH smoother with the Crayford-style focuser. I ended up stripping the plastic threads on one of the setscrews…
Moved the notch for the ECAS04 to the center of the part. Use standard Voron print settings.
End Cap for OpenBuilds extruded aluminum (adapted from other designs)
Remixes the main knob so it can be slip-fitted on a Bresser Hexafoc Focuser. Tested on Bresser AR102s/600 refractor but it should be working for any Bresser Hexafoc 2.5" Focuser (?)(TBC). Adds an attachment plate that fits the focuser…
I just mixed up GreaseMonkeys brilliant small power button model , it's been adapted to be used with the Wokyis Dock to combat the thicker edge of the dock itself and helps stop the annoying way you have to manhandle the dock and mac mini…
Amended faceplate to fit https://www.amazon.ca/dp/B098L7WJ4C?th=1 USB splitter ports
Remix of the LED holder for a different style of LED light: https://www.amazon.co.uk/dp/B0DJ73G4PX?ref=ppx_yo2ov_dt_b_fe
GEN2 Decor Handles - Adjusted for 12mm screws instead of the default 16mm and a bit ‘more chamfered’ for esthetics.
Updated to: Use a smaller diameter main knob for more clearance from the diagonal on a C5. The new main knob is the same diameter as EleusisT's original. Use snap fit connectors to secure the reducers' support to the secured base plate.…
Game Boy inserts for cassete box I buy from aliexpress some cassete boxes for my GBA games and discovered they where incompatible (not close well) so I modfied some ones to make it fit GB/GBC made by @EntirelyTom_2031571 GBA made by…
I had problems mounting the front part of the Morrigan class, this was only possible by a modification more bad than good (see photos). I have therefore slightly modified the mounting of the part so that it now fits without any problems.
Spool Holder based on the TUSH model for ¼" (6.35mm) ball bearings. These bearings are common in the US. Printed in Overture PETG on a 0.6mm nozzle. Settings are based on the Mk3S/+ 0.6mm nozzle and Prusament PETG config. I add additional…
This 4010 extended blower duct is specifically designed to optimize airflow for the K1 CHC (Ceramic Heater Core) Hot End , seamlessly integrated with the Toybox Alpha 3D Printer's stock fan location . The duct channels airflow efficiently…
This is a remix of the original Fan Shroud model to allow mounting on the Hydra Fan Duct: https://www.printables.com/model/169197-hydra-fan-duct-tool-change-system-for-ender-3-ende The duct is no more straight but slightly pointing…
Currently the model is at 1:1 scale which won't fit most printers (table top dimensions are 392mm x 335 mm). Tolerance are 0.2mm between the parts, so some rework might be necessary if scaled down for printing. I'm still working on a…
Ryobi One 18v router base adapted for using with router bushing
UPDATE: This cooling solution is only good if you have only 40mm or 60mm direct fan. There is much better cooling option using dual 5015 turbo blowing fans on slower speed . Remixed 40mm fan duct with wider air flow pipe to better and…
I decided to install JBL GX328 speakers instead of the Infinity speakers. I chose these speakers for their lower impedance, which more closely matches the stock speakers' 2-ohm impedance in my JBL system. I found out that they will not…
This is nothing particularly special. I created it to go with Dakanzla's magnetic tiles here: https://www.thingiverse.com/thing:1238980 If you want to know how I got the gold sheen on the paint job, I stood about 6 foot back with a can of…
I made a compact ultralight slip case to protect my new DJI Mini 3 drone and RC-N1 flight controller when motorcycle camping. It's as small and lightweight as I could make it. Each of the overlapping side walls are 1.5 mm thick, so the…
Adaptada la carcasa para un NRF52840 y un SX1262 Tambien he agrandado el hueco de la bateria, ahora tenemos un hueco de 41mm x 25mm aprox., yo le he puesto una bateria de 1350 mAh y un bms y cabe perfecta. Dejad en comentarios si teneis…
Makes it compatible with the Magni. There is a model built in, as well as wing adapters for the original.
Categoría : Producto de apoyo Contexto de uso: Alimentación y ocio Modo de uso : Para abrir latas mayoritariamente de conservas y/o con anillas grandes y de gran recorrido de apertura (sardinas, mejillones, etc.) Recomendaciones : Los…
Altitude Select Knob for push pull encoder and 100/1000 select on A320 FCU adapted for Santi Luib III Mark 2
Drill dust collector adapted to work with a 26mm diameter hose used for washing machine drain pipe. This is part of my other model adapting the same pipe to be used with the Xiaomi Mini vacuum:…
Fully based on and all credit to Sovol SV06 Fan Duct 5015 Blower Fan V3. Adapted the backplate so it fits in combination with Sovol SV06 (Plus) extruder mounted cable support . Printed in PETG, 0.18mm layer.
I reverse engineered the AUKEY Table lamp adapter pattern and put it on the bottom of the moon. The moon now mounts into the AUKEY lamp, and can have multiple RGB colors or bright nesses…. the AUKEY Lamp base is sturdy and supports the…
adapted some of the parts to hold lenses from fuji film quick snap disposable cameras
model reshaped to fit ikea 205.431.57 led light
Added 1mm more space for the display thickness Added buttons Customized back plate
Just a handy small piece which allows to mount a Headlight straight to the BBB Stems that are compatible with the GoFix Mount from BBB. Listed models on BBB website: BHS 09, 37 und 38Di2 but also fits the Actionstem BHS-52 as you see For…
I modified this to attach to Molle as opposed to the knife. Thank you for doing the work on a great fire steel holder.
Original stand and front cover still fit, please get the originals there, or use the ones also in the 3mf i widened the usb hole (my usb port was on the side, not the middle) Now the board is flippable. And i adjusted the bar to fit the…
most din CB's have a notch behind them which does not allow them to clip into the original part, so that plate was remov
Bento Box Filter Remix – 5020 Fan + Quick-Release A remixed Voron “Bento Box” air filter with a 5020 blower for more airflow and a quick-release lock for easy filter swaps. Still uses 4 magnets and the original filter cartridge (download…
Fish feeder, with bottle hopper adapted for arduino case and sg90Fish feeder, with bottle hopper adapted for arduino case and sg90 All printed with PLA Only change I really made was to the base, so the the arduino nano case can fit in…
Someone asked where to get extra tops for the citadel handle so i did a simple smash together of existing creations to fit. Get the clampy bits for the top from icnorman here https://www.thingiverse.com/thing:4152882 Made using the…
