Liczymy pasujące modele…
Print Video: Description : The Garmin Instinct Charging Dock V2 is a innovative solution for Garmin Instinct watches which do not come with a charging dock. I was bothered by the fact that my Garmin Instinct had to be kept side ways while…
This is an universal Garmin mount that I've designed to attach whatever you have in mind (having at least a flat surface, though) to a Garmin support. You need to use 2 TPU o-rings to attach your device to it. I've used it to make my…
Minimal clamp to mount a Garmin Varia (or compatible) on a 27.2mm seatpost. It's a very tight fit and a tiny M3 x 5mm screw is used additionally, but very gentle. I used PLA, 0.2mm structural and 3 perimeters. Organic support and 0%…
I got tired of my smartwatch charging connector sliding around the nightstand and the watch ending up face-down on the cable. This dock screws to a wall (or any vertical panel) and holds the charging puck in a hole, so you just drop the…
Overview This custom-designed charging dock combines function and minimalist aesthetics, tailored specifically for Apple MagSafe-compatible iPhones and the Garmin Fenix 7/8 smartwatch. The dock consists of two interlocking base…
This print consists of the base and 3 thumb screws for leveling adjustment. The base can be printed as a single color, or with 2 colors for MMU2S users. Import the base STL into PrusaSlicer and choose ‘Split to Parts’ to see the alignment…
GARMIN compatible mount (both sides), can be used as a base for other designs. Step included. Category: Sport & Outdoors
There are loads of Garmin interfaces out there, but (in my opinion) they all fail for one of two reasons: the intended print orientation is horizontal, thus mandating support structures that are difficult to remove and leave residual…
Another Garmin bracket, this time with mountain bikes in mind. The clamp can be printed in place, with no supports necessary. The interface itself is in several parts, to improve durability and make it easier to print, again without…
Garmin (FENIX) watch stand with charging option. All you have to do is print and clip the original cable. There is no need to purchase any additional charger
A simple, modern-looking planter. I printed mine with a 0.4 mm layer height, resulting in single-wall edges. It was a little experiment that took about 3.5 hours to print. I’m sure modern printers can handle it much faster. Please note:…
Garmin Edge Mounts that goes under the stem cap. Normal version and a Giant OverDrive version. The mount geometry is partial remix from Eric van Helmond. Category: Sport & Outdoors
Stuff you'll need: 1x Garmin insert (I took the one that came in the box, remove and keep the 2x M3 screws) 2x M4x8 SHCS such as these - https://boltdepot.com/Product-Details?product=6392 Start by screwing the printed model onto the…
3003 Fantasy Bits Mega STL Collection on Kickstarter 🔥 Want to stand out in the 3D printing market and attract more customers? 🔥 Sell unique, stylish, and modern 3D models with a commercial license – no restrictions, full freedom! 💸 Why…
This model is a remix of my previous bullseye spirit level stand that used an alignment stick. Now to get the path tight, we will use a laser! This print consists of the base and 3 thumb screws for leveling adjustment. A Ryobi Laser Cube…
A small adapter plate to convert a quarter-turn mount to 2-pronged GoPro. There are plenty of models to convert to a 3-pronged GoPro mount, but I struggled to find one to go to the other side of the GoPro mount. Note that there are two…
If you have an integrated Garmin support and broke the plastic part, this one is for you ! WARNING : it's designed to work with the aluminum support, not alone (see photos) Print instructions Category: Sport & Outdoors Summary If you have…
Garmin Varia Radar - Bicycle Saddle Mount - also available for similar light versions The possibility of securing with zip ties - adapted for the original garmin holder Minimal supports Fast and easy print perfect snug fit Double…
A collection of Garmin ¼ turn to GoPro mounts, with variations of both male and female, 2 and 3 prong. All use an M5 bolt and nut. Available for sale on eBay: Male Garmin ¼ Turn Female Garmin ¼ Turn Printing Orientation: Male ¼ turn…
Garmin Edge computer compatible out-front handlebar mount for 34mm handlebars Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.16mm Infill: 30% Filament: Spectrum ASA275 black I have printed it…
v2: Top surface is flat now so it can be easier to print upside down sturdier constrcution through softer radii Original Garmin and Wahoo mounts can be used with screw holes, mounts will fit without protruding Update: Wahoo compatible…
A simple GoPro camera mount that can be attached to the bottom of Garmin Out-front bike mount securely using M3 screws. Another version which includes a vertical post mount (e.g. lights) can be found here . For more information on this…
Garmin fenix 5 watch charging stand
Update November 2024 NEW 10xx version: I added an elongated version of my GarYon v4 design to match larger bike computers. Durability experience: Until today I rode about 3500 km with the reinforced original design without any integrity…
Cover for Garmin LiveScope Plus LVS34 Transducer
This money bank is big enough to contain coins and bank notes when you are saving for rainy days. The Main Body is a single piece so a color change is needed if you want to have the base in a different color. The Top part screws onto the…
This is an adapter that allows you to mount the Garmin Varia radar to a Trek Blendr seat mount. This requires the blendr mount with a compatible saddle, as well as the insert from a Garmin Varia mount included with the Varia. The Garmin…
The only hardware you need to supply are two M3 inserts (I use ruthex) and two M3x6 (or 8mm) screws. I printed mine in PolyLite ABS, but PETG would probably be more than enough. I don't recommend PLA. Be sure to account for shrinkage if…
While you can insert coins through the letter slot, larger banknotes can easily pass through the top functional flip-down tray. The whole mailbox can be printed and put together within a weekend or less. Although this model necessitates…
My take on a sunshade for the Garmin Xero C1
Some notes: Can you please leave a comment with your watch model to confirm if the design fits, I would highly appreciate it! :) Also, if the model you are looking for is not listed, I can adjust the design to any model if you are able to…
This watch stand holds your watch, as well as your puck-style charger. There is also a version that will hold the stock charging cord instead of the puck-style charger in case you don't own one. I have designed these models with the fenix…
This adapter attaches to the underside of a Garmin Flush Out-Front Mount and allows the use of any accessory that has a 2 tab GoPro style connector. In order to attach this to your Garmin mount, you will need to replace the stock machine…
Simple adapter for a wahoo head unit to fit onto a garmin mount, the other designs here seemed to be unnecessarily thick.I printed it at 100% infill but you could probably get away with less, id recommend printing it on its side (with it…
As said, two versions with and without Gopro mount. The uploaded STLs are designed for an inner spacing between the bars of 75mm and a bar diameter of 22,3mm but those parameters can be fitted to your needs in Fusion. parts for Gopro…
A small adapter plate to convert a quarter-turn mount to 2-pronged GoPro. There are plenty of models to convert to a 3-pronged GoPro mount, but I struggled to find one to go to the other side of the GoPro mount. This is designed to accept…
Fiz este desenho pois o suporte que tinha do meu garmin 800 não era compativel com o 1000 O que vinha o GPS ficava mais alto. Gosto de o ver em linha com o avanço Isto ainda não é a versão final English version (google translate) I made…
This is a charging stand for the Garmin Vivoactive 4. Simply insert the original cable from the bottem and secure it in the slot. The part prints without supports. With the 0.3mm Draft profile on an MK3 it will take less than an hour.…
Learning F360 and made this stem mount for my garmin GPS. It's shown with a garmin insert, but if you search for “garmin k-edge” you can find a printable one. The screws just self tap into the mount, although you could use longer ones…
Soporte de Garmin para el manillar de canyon h31. El soporte original vale 30€, entonces pensé y si lo hago con la impresora. Después de muchos modelos y diseños diferentes he conseguido este, está en proceso y aceptó propuesta de mejora.…
Charming Bird Figurine – A Delightful 3D Print! Bring a touch of nature to your space with this beautifully detailed 3D-printed bird figurine! Designed with intricate feather patterns and a lifelike pose, this little bird makes for a…
Charging stand for Garmin watches. Print Profile: 0.2mm layer 3 walls 15% infill
The GEAR GROOVE Garmin Mounts are sold out on the website, so I added the lock made by @Trunda_1437739 to a GEAR GROOVE model. Included are 2 .3mf files; one in normal orientation with ironing on top level, but the upside down orientation…
I was struggling charging my watches and still be able to see / operate them. So I made this stand wich fits the original charging cable (slightly pressed in) - please check attached model dimensions to verify you have the same plug on…
Minimalistic and very light (~7.5g) Garmin Varia mount for 27.2mm round seatpost with 73.5 seat tube angle. Designed and printed as a single piece, mounted to the seatpost wiht the rubber band. Set support on build plate only and paint…
Minimalist Garmin Varia seat post mount for Canyon Ultimate (2024) D-shaped seatpost The seat post should be printed in ABS or another semi-flexible material Required hardware: 2x threaded heat set insert M3 x 5 x 4mm (Voron standard…
This is a mount for the Garmin Varia 715 light for mounting directly to the seatpost. Needs a separate insert from k-edge (K13-504 https://k-edge.com/shop/computer-mounts/garmin-mounts/replacement-garmin-insert-kit/), and a single M5x18mm…
I have added a sunshade to the design of Kytu. ( https://www.thingiverse.com/thing:4446393) Unfortunately, you have to print it with supports now. So a little bit of cleaning in the end is necessary. I printed it with 15% infill, 3…
Very simple print. Meant to be printed vertically. Mine is printed at 0.3 Layer Height in PLA. if you like this soap tray, click here or here to see other similar designs. And if you’d like to support my work, leaving a ♡ like ♥ or even…
This is a simple customization of HAMMER_T's Garmin Mounting Clip to mount my Garmin Etrex 30 on my Canyon mountain bike. I used a small piece of an old air chamber to make it grip on the bike. I printed it in ASA because it can happen…
Garmin Fenix 6 stand Easily printed without support + stp file available
This is for your XT2. You can use it as a bumper or add the sun screen for extra utility. Print it black or crazy colors to customize your bike. If you print it please upload a picture and share your creation thanks! If you like this,…
Should fit Garmin striker 4 plus and cv plus. Attaches without adhesive and prints without support.
This is a replacement cap for a super stroke grip for a golf putter. Also included is a version of the cap which can be printed in TPU and used with a Garmin CT10 club sensor. Normally this sensor simply screws into the end of the club…
Garmin mount suitable for smaller Garmin devices (Edge 840 or smaller) for the ROSE Backroad FF. Print it, add the Garmin or Wahoo mount insert from the mount that comes with the device and mount it with 2x M5 countersunk screws. The…
Stand for Garmin Epix -watch, you can attach Garmin charging cable to the stand. The hole for the cable is tight enough so it holds without glue or other adhesive. Must use support for printing, I used Tree support and it worked just…
Mounting rail/arm for the Garmin Xero C1 chronograph. Comes in three lengths (3", 4", 5") with either the 17S footprint (for use with Area419 ARCALOCK clamps ) or a generic footprint that should work with Amazon sourced clamps (eg.…
This is a replacement for my broken Garmin Fenix watch band strap loop. This link is to 3D View http://a360.co/2wgV0eJ Print instructions Category: Gadgets Print Settings Printer: Anet A8 Supports: Yes Resolution: .08 Infill: 100
Garmin Edge mount with more clearance than the original for chunky handlebars. This version has a chunk cut out under the mount for mountain bike bars. If you don't need the extra clearance, I'd recommend the original for better strength.…
Mini 3 clip coming soon! Light weight Garmin inReach mini clip, designed from the ground up, to be as light, yet sturdy as possible. Designed to be used with the lanyard attachment, and supplied hex screw. Confirmed that this also fits…
Sliding case for the Garmin Xero C1 Pro, tripod and cable. Magents used 5x5x2mm
Designed this pot because all the other vase-mode ones I printed kept breaking. It works particularly well with satin and shiny filaments and still prints reliably if you tweak the scale. If you’d like to support my work, leaving a ♡ like…
I've printed a few charging stands that hold the puck-style charger for a Garmin Fenix series watch. They've all been fine… but I decided to take a crack at modeling my own. It's a little more compact than the alternatives, and I tried to…
Hey! This is Garmin Vivoactive 3 Smartwatch / Sportwatch holder for your bike. It allows you to mount Smartwatch on the handlebars with aid of 2 zip-ties. Smartwatch is strapped on the holder the same way as it's on the hand. It provides…
Description Garmin just released a new version of their popular Varia Radar system: the RCT715 . This product diverges from the rest of the Garmin line, in that it no longer has the quarter turn mount, and the existing mounts out there…
made this so I could mount my bike computer and light in a more compact package. My bike light had a GoPro mount but it wobbled too much and messed up the out front mount that came with my bike computer. I made this and printed a rough…
YTGRRL Summer Update!!! NEW BBD MAGNUM MODEL, now with EXTRA CLEARANCE for your baggage. By popular demand, the shaft is now LONG. This WILL lead to breakage, but I am here to please. Garmin quarter turn mount for Fizik saddles with an…
A stand for the Garmin R10 Approach, that will allow you to level it on the course, or at the driving range. The hole in the middle if designed for a 32x7 mm levelling bubble. Print at 0.10 layer height for best results.
Garmin Mount for the Canyon Aeroad (2023) Model. nedded Prints: 1x AeroadGarminMount 1x garmin-interface-spring 1x garmin-interface-lockring 1x assembly-tool (only for assembly) other needed Material: 2x M4x14 Screws (or similar length,…
better springing action, lighter tolerances , thicker on legs, + fillet
Replacement watch band loop for the Garmin Forerunner 245. Tested and feels most comfortable printed in TPU. Print with supports. Print with supports.
You can use it for example for fitting your garmin varia front light to garmin cyclocomputer mount.
Double Universal Out-front Mount, for Garmin accessories. Use m3 screw/nut to close the fixation. V2 : rework fillet on fixation to the bike Printed in 0.2mm layer height, 20% filling with PLA+
This is a mount for the Garmin Varia 715 light for mounting directly to the seatpost. Needs a separate insert from k-edge (K13-504 https://k-edge.com/shop/computer-mounts/garmin-mounts/replacement-garmin-insert-kit/), and a single M5x18mm…
A friend of mine has a problem that the metallic connectors on the charging port gives her rashes. She is very sensitive to earrings and jewelries as well. To allow her to wear her watch all day i created a small cap to cover the charging…
Remix of @TinkrMakr model to be a little bit more hand charming. I beveled the edges to make it feel better.
This is a mount to allow a Garmin Varia to be fitted to the blinky loop/LED light loop commonly found on saddle bags and cycling messenger bags/rucksacks. This version has the quarter-turn mount designed by El Manu included in the print.…
This is version 2 of the Garmin GPS mount for the later type fitting in the 2017 Citigo, Up and Mi which have a USB socket under the base. The neck has as a 17.4mm radius ball to match the standard socket on Garmin GPS brackets. It should…
This is a holder for Garmin Radar Varia for a Canyon Aerorad bike. For seatpost SP0077 This is printet in PETG with 40% infill. Feel free to use. Desigend in Autodesk Fusion 360 I will make a version with pressfit nut also.
This is a Garmin Varia saddle mount using the Bontrager Blendr saddle mount system. No hardware is needed in the model. Allen screws are needed to mount to the saddle, otherwise the Garmin mount is built in. It should be printed with…
Its a stand/charging dock for Garmin Forerunner 255 :) If u find some error please comment!
This is a rear bike rack mount which uses a Garmin quarter turn insert. My rack light mount has two holes 19mm apart and accepts M5 screws. The M5 hex head screws I used for this came off my previous rear light's mount. Required: Garmin…
Wanted to make a more sleeker looking cover of my own earlier uploaded Design Print instructions printed on prusa i3 mk3 with PETG 0.15 layerheight The one I printed in the example is a little different because I added an extra Logo on…
This is a remix of the excellent Garmin Varia mount by Tim Angus. It requires minor assembly but locks in place securely. Printing instructions: Use PETG for strength 0.15mm layer height Print the main clip with the broader side on the…
Using the original Quad Lock Handlebar/Stem Mount to start from (see picture), this Adapter replaces the handlebar part to fit on a Garmin mount. I did that for the time I ride my bike indoor on Zwift and want to have my mobile phone…
Garmin mount to take advantage of Uniclip system on the saddle for attachment
The Garmin Oregon 600 Navigation is otherwise a sturdy device but may become non-functional due to the degradation of rubber buttons over time. The recommendation from the manufacturer is to buy a new device, which is very environmentally…
An adapter to mount a GoPro camera onto a garmin mount designed for cycling computers etc.
Print with ASA or PETG Layer height 0.2 No supports 2 walls 3 top and bottom layers 20% gyroid
Hardware 3x M3x8 bolts 1x M3x12 bolt 4x Threaded Inserts OR M3 Nuts What to print? There are 3 types of base part depending on thread solution You want to use. Base_[5mm] - for M3x5x4-6mm threaded inserts with 4.25mm leading diameter…
Garmin-Style Tablet Holder (30°) for Indoor Cycling This Garmin-style tablet holder allows you to mount your tablet directly onto any standard Garmin quarter-turn mount during indoor cycling sessions. Perfect for Zwift, Rouvy,…
Modified a computer mount design I found to be compatible with Garmin computers.
A simple replacement free loop for the Garmin Forerunner 935 or any other Garmin with a 22mm band. Made in Fusion360, it is intended to be as true to the original as possible. Printing Instructions Print on its side for best results.…
The size and offset of the base plate is modeled to nicely fit this Garmin Varia mount for the Specialized SL8 . Needs a M3*8 countersunk screw and nut
Disclaimer: These models are created with the help of AI tools, but always refined with my own ideas, prompt work, and post-processing for printability. I deeply respect traditional 3D designers and their craft, and my goal is simply to…
Garmin/Sigma Rox 11 mount above stem Again another Gramin / Sigma Rox 11 mount for a handlebar diameter of 31.8mm. I Designed this for my own needs (fits perfect over a canyon v12 stem) so i hope it fits for you. It's easy to Print but…
Garmin mount designed for the best view of your Garmin. At the same time, the mount also serves to attach the light. Made in two versions (holes for light rotated 90 degrees). The models also include a model of the pad between the mount…
Clamp for aero seatpost of Factor Ostro VAM road bike. Provides action camera / garmin varia mount for use with any item with a action camera mounting feature. Print in PETG, ASA or Nylon 100% infill 7 Wall layers This is to make the…
![Garmin Mount for Aerobars [parametric]](https://media.printables.com/media/prints/878658/images/6738792_8b57a8b9-5bd2-4d0c-9765-a5bec375e787_55f80f7d-9ae8-4304-b229-628c4828e804/20240513_114330.jpg)
