Liczymy pasujące modele…
BACKGROUND: The Elecraft KH1 blew up the portable HF radio operating scene when it was released. It covers 5 bands from 40 - 15 m and has an internal ATU and battery. It's actually designed for hand-held use. But with the standard whip…
Wydruk około 0,49 €–0,60 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The stock Elecraft AX1 and AX2 clip for the bipod is very stiff, difficult to attach, and hard to remove. At the request of a fellow op, I designed a better one. Here it is. Print in PETG for flexibility and durability. Print the clip…
Protects top of radio, display, and knobs from damage. Remove existing side panels by taking out screws and nut securing microphone connector. I printed these in PETG.
Requires a BNC angle connector!
About This is the first draft of a stationary or portable stand for a stack of Elecraft KX3 radio and Elecraft PX3 panadapter. The radio and the panadapter are stacked on each other, steeply raked, to create a compact and comfortable…
I printed the AX-1 storage card in PETG, 50% infill, 5 walls, 0.2 mm layer height. Both .step and .stl files are attached for whatever format you prefer.
I wanted a better knob for the KX2, but one that was also still the same size to fit in small cases and to work well with after-market radio covers. The finger indent allows quick tuning and efficient spinning of the dial with no added…
Clamp for Elecraft AX3 antenna. You will need to buy a ¼-20 pan head or socket head screw. for each one. I print all my clamps and brackets using ASA but I am sure petg will work just fine. Updated clamp and velcro bracket. This new…
Replacement clip for the Elecraft AX1 ham radio antenna. I printed with PLA and it works well.
This is a protection cover for the Powerswitch on your Elecraft KH1. It helps to protect your PA of any damage and empty batteries. Material PETG Layer height ≤0,1 mm Infill 100% Support None. The model was designed not to require any…
This video walks you through how to make a 10m base-loaded shortened vertical that is small and lightweight, and it shows you the start to finish of how to design one for any band! I used online calculators to figure out the inductance…
If you want to use Li-ion 18650 battery (like original KXBT2) internal in your Elecraft KX3 instead of NiMH batteries, you will need this new holder and retainer. Material PETG or better Layer height ≤0,2 mm Infill 100% Support None. The…
This is a set of magnetically attached covers for the Elecraft KX3 and PX3. These require common 6mm diameter by 2mm depth magnets. Designed in OpenSCAD. Since all KX3s and PX3s are hand assembled, I recommend trying the test print option…
This is a stand for the Elecraft KX3 and KX2. The smaller stand is designed for the matching Panadapter. The stand can be used for other devices like HT radios. You will need to duplicate the number of parts needed for each project. Print…
I have created a small portable knee board for the elecraft kx2. You will need a strap of some kind 1"½ wide . 2.5mm elastic shock cord and a large fender washer. I recommend sizing the fender washer to fit after printing the board. When…
Elecraft KX2 VFO knob Recommended 100% fill no supports needed. I used ASA but petg would also be fine.
Beschreibung The Original VFO Knob of the KX2 does Not feel good when you try to Spin to a new frequency. This remix of my QMX VFO Knob is a bit bigger to use the available space at the Front of the KX2 and contains a dimple for your…
This is a stand I designed for the Elecraft KX3 and PX3. You will need to print two of both STL files to make the stand. I forgot to add the cross brace for the bottom and back. My QRP Club the North Georgia QRP Club offers a very nice…
Edited 2/28/26 with new links for the items needed. I am open to improvements and tweaks - please contact me directly or leave a comment. I designed this KH1 kneeboard for some friends in the amateur radio CW community. In addition to the…
This is a simple project to add a Bluetooth Low Energy (BLE) UART to a Elecraft K2 or any other radio with a proper RS232 interface so that it can interface with logging software. BLE is the only interface that iOS supports for example. I…
January 7, 2024: Added some more performance data to the bottom of the original blog post on what happens with key down.. https://holdmybeer.io/2023/12/22/ham-stack-fan-shroud-for-elecraft-kxpa100/ January 4, 2024: I recorded a timelapse…
The "Thrifty" KX3 Desk Stand is a simple, functional desk stand designed specifically for the Elecraft KX3 transceiver. The design supports the KX3 using its built-in rear legs. This model was created as a practical replacement for a…
Here's a push-on front panel cover for the Elecraft KX2. It's meant to be pushed onto the front face of the radio and provide some protection to the knobs and display from damage if your bag gets knocked or you fall on it. Print Settings…
A variable length spiral leg that allows stepless adjustment of the Elecraft KX2 radio's tilt angle. Folds back behind the radio for transportation. Replaces the default fixed single length tilt leg using the same thumb screw. What…
This is a stand I designed for the Elecraft KX3 and PX3 using Fushion 360. You will need to print two of each STL files to make the stand. I forgot to add the cross brace for the bottom and the back. My QRP Club the North Georgia QRP Club…
Pictured in Bambu Lab TPU 95A HF; also tested in PLA. Should print fine in other materials but may require adjustment or drilling if the holes in the 4-pin connector come out too small. Three options for the “KEY2” legend: none: flat…
Covering for magnetic pogo pin useable on the earthconnection on your Elecraft KX2 Material TPU Layer height ≤0,2 mm Infill 100% or Walls 10 Support None. The model was designed not to require any support material. pogo pin…
This dog bone antenna winder has holes to allow an Elecraft AXT1 Tripod Adaptor to be mounted to it for more compact packing. It is sized to pair with Mike Roberge's AX1 Storage Card available on Printables.
This remix is designed to allow the Elecraft KX2 to retain the rear leg (in fact I use the taller leg ) at the expense of space for the KXPD2 (which I don't own). I use the space in front of the radio to store my AX1 with AXE1 and AXB1.…
This is a stand that is for desk use or in the park. Any where you need to operate from. You can print this in any material you want I printed mine in petg. 15% infill no supports. You will need 2 10mm dia x 4mm thick. Not in the pic is…
A single piece enclosure for the Elecraft DL1 Wideband Dummy Load kit . This close-fitting enclosure is open on the bottom, to allow use of the rubber feet included in the DL1 parts kit. It has an open grill over the resistor grid to…
v2 Updates Standard version Softer edges throughout: a 1 mm chamfer on the bottom (which also prevents elephant’s foot) and a 1 mm round-over on top. The walls beside the KX3 foot pockets stay square so the feet still lock in. Shock cord…
Desk Stand for the Elecraft KH1. You can print it using PLA Or better. Infill 15% walls 2. Supports a must. I used Auto tree supports. The tabs on the sides are for Shock chords same as I used on my knee board.
12/28/2023 Update Filleted parts to make them easier on the hands and included a “fence” around the fans (visual and cuts back some of the sound from the fan intake side). The fence is very thin and only intended to obscure the fan…
Limits the wobble of the Elecraft KX2 radio's somewhat less-than-perfect VFO encoder. The spacer wraps around the encoder shaft with a very small tolerance and provides physical support against tilting/wobbling motion of the shaft. The…
This is a generic mount for an Elecraft KX2 transceiver. I have purposely not added any specific screw holes or other features for attaching the mount to something. If you desire, you can add features to the generic mount to mate up with…
Printed in PETG, it's split into two parts to fit normal build plates. Recess on the front right is for the lovely BaMaKey TP-ii. Recess on the back fits a 6Ah LiFePo from Eremit. PowerPole to DC adapter for the Elecraft KX3 can be…
Just a simple knob that presses onto the factory nut. It makes it easier to grip without blocking the banana plug port, and if you print it in a bright color, you'll find it if you ever drop it! I printed it out of PCTG but PETG or TPU…
A small accessory for an Elecraft K3 to bring the key and paddle jacks out to the front. How I Designed This OpenSCAD Category: Electronics
Requires the GEMS Products Side KX PX3 End Panels: When in use, it snaps into the handle openings in the End Panels and extends upwards to shade your PX3 display from the sun. When you're packing up, reinstall it upside-down and it…
This is a special box for Elecraft KX3 owners to store their KX3 radio and accessories in an adjacent space. The box is a reworking of the excellent Frog Box, originally designed and posted on Thingiverse by user Nibb31. Size…
PETG Recommended Print on edge to allow for maximum strength when clipping and unclipping. It prints without supports. Make sure your print bed is CLEAN, there is not a lot of contact area on the first layer. If it struggles to print, use…
Printed in ASA for strength fill needs to be 45% or higher. The screws for the side of the amp are 10-32 x ½ long. Tighten the thumb screw on both the radio and panadapter prior to putting on brackets. the same brackets fit both.
This is a battery adapter to use a 3S Li-Ion battery instead of AA-cell or NiMH battery inside the Elecraft K1. It has the same dimensions like the original KBT1. The top cover are easy to remove and you can charge your Li-Ion batteries…
The "Thrifty" PX3 Desk Stand is a simple, functional desk stand designed specifically for the Elecraft PX3 Panadapter. The design supports the PX3 using its built-in rear legs. This model was created as a practical replacement for a…
Designed with OpenSCAD.
I printed these in Bambu Lab TPU 95A HF and, while not as tacky as the factory feet, they are functional. They also work printed in PLA in a pinch, but of course won't provide any traction.
You will need a section of 1/8 shock chord and Reflectix. But for the shield you can use any material you want. In one of my photos I used a paper plate. See video I created
I broke the plexi cover from my KX2 Windcamp shield kit so I recreated a 3d printable replacement.
These are two simple covers for the KH1, one a cover only and one with a telescoping whip attachment. They also allow charging and protect the on/off switch from accidental activation. I made these because I prefer tabletop POTA type…
Inspired by the excellent work by goss over on thingiverse ( Elecraft KH1 - BaseCap + AntennaCap (STL) by goss - Thingiverse ), I created a protective cover that will protect both the factory paddles (KHPD1) as well as the excellent…
This is a progressive modification of my KX2 cup mount for the KH1. Great for mobile CW ops or POTA activation. Print the two attached files along with this file for the mount swivel: Swivel Mount Low-Profile AMPS (30x38mm) Swivel Mount…
The "Thrifty" KX3 Desk Stand is a simple, functional desk stand designed specifically for the Elecraft KX3 transceiver. The design supports the KX3 using its built-in rear legs. This model was created as a practical replacement for a…
PETG Recommended Print on edge to allow for maximum strength when clipping and unclipping. It prints without supports. Make sure your print bed is CLEAN, there is not a lot of contact area on the first layer. If it struggles to print, use…
The "Thrifty" PX3 Desk Stand is a simple, functional desk stand designed specifically for the Elecraft PX3 Panadapter. The design supports the PX3 using its built-in rear legs. This model was created as a practical replacement for a…
