2838 modeli
This splint prints flat and can be easily molded to perfectly fit your wrist with a little heat (hot water, heat gun, oven, etc.). It is designed to comfortably immobilize your wrist, preventing ulnar and radial movement, while still…
This cute dinosaur sand mold will bring happiness to your younglings in the sandbox or at the beach. Printing : 0.2mm layer height works well. Scale as you wish and print with the flat side down without supports. ***UPDATE*** 03.08.2023 -…
New molds, much better: https://www.printables.com/model/1185152-new-better-crucible-molds-for-microwave-metal-melt There are 2 different size molds. I print them in PLA 20% infill. The Lid and inside cups should be printed @0.16 mm layer…
Create long-lasting flames with this waterproof firestarter! Flames last 10+ minutes, even in the rain! No plastic is burned for this model - instead, the mold is used to create a waterproof wax and dryer-lint (or sawdust, paper, etc)…
An easy to print geometric starfish sand mold with no supports required. Print flat side down and scale up or down as desired. Example photos are printed with Prusament PETG Pistachio Green at 0.2mm with a 0.4 nozzle and 15% infill.
Molds to create rice-based deliciousness. (Onigiri & Musubi). The onigiri mold fits is designed for half of a sheet of nori and then the musubi mold will fit a slice of spam. NOTE!! Please ensure that you are using food-safe filaments (eg…
🏚 Simple and elegant ceiling lines decoration. Or it can be used as a corner cable cover. Print instructions ⬢ Material: Prusament PLA Vanilla White ⬢ Layer: 0.2 mm ⬢ Dimensions (1pcs): 50 mm x 50 mm x 190 mm (1.97" x 1.97" x 7.48") No…
The cubes measure 4×4×4 cm. There are 2 pictures on each cube that you can use to stamp into modeling clay or kinetic sand. Inside there are molds for different objects. The cube develops fine motor skills, vocabulary (create stories),…
Side molding clip for an EF Civic, possibly CRX or other models from the 86 era. Layer size: (0.15-0.1) Material: ABS Supports: Yes
Grid to place into the DeLonghi Magnifica S container to avoid mold.
A great Christmas gift. I recommend wrapping the entire mold in a blanket or insulating it right after pouring the wax into the mold, and letting it cool at around 20°C for a slow cooling process. Rapid cooling may cause the candle to…
A Plain Soap Mold designed for the home soap maker to mold a bar of soap. The mold can be easily 3D printed, without any support, on a modern inexpensive 3D Printer. It can be printed with a variety of heat tolerant materials, including…
I couldn't find molds for sand anywhere, I needed them for kinetic sand, I designed a couple of them and I'm uploading them to pritables for further use :) GCODE FOR ENDER 3S1 RUNNING ON KLIPPER!!
Pretty basic idea: 6in Tapered Candle Mold. Just print both halves, bottom up with organic supports - to hopefully produce as smooth a mold as possible. Should produce a tapered candle about 6 inches long with a ¾ inch base. I'll post…
Side molding clip for an EF Civic, possibly CRX or other models from the 86 era. Layer size: (0.15-0.1) Material: ABS Supports: Yes
Little known fact: I bought my first 3D printer so that I can print leather embossing stamps. This actually works pretty well if you are interested in it yourself. So to go back to my roots for a bit – and fitting with the Catch-All Trays…
This is a single-use mold, once printed it must be filled with plaster and left to dry. After 24 hours it must be placed in the microwave every 30 seconds to soften the plastic and remove it. Once ready the pieces fit together perfectly…
Výška Osieho hniezda - koláčika : 4 cm Priemer podstavy: 3 cm (presne na piškotu) Ak sa ti model páči klikni na srdiečko. Ďakujem. Height of the Axis nest - cup: 4 cm Base diameter: 3 cm (exactly for sponge cake) If you like the model,…
Snowman mold. Print two to complete the snowman. You might be able to make each side of the snow man separately, but I found it's really hard. Have fun with your kids in snow. Feel free to ask any questions or report any issues. Happy…
Side molding clip for an EF Civic, possibly CRX or other models from the 86 era. Layer size: (0.15-0.1) Material: ABS Supports: Yes Raft: Yes
velkosť laskonky: 5 x 7 cm velkosť celej formy: 16 x 18 cm velkosť plechu na pečenie do ktorej sa vojde forma 4 krat: 34 x 37 cm Ak sa ti model páči klikni na srdiečko. Ďakujem. cake size: 5 x 7 cm size of the whole mold: 16 x 18 cm the…
The cubes measure 4×4×4 cm. There are 2 pictures on each cube that you can use to stamp into modeling clay or kinetic sand. Inside there are molds for different objects. The cube develops fine motor skills, vocabulary (create stories),…
Mold for reinforced concrete bowtie, recommended to use PETG.
This mold is used to make a suitable seal for Lukas Cenovsky's card shuffler from basic materials that are easily available or available in the household. I used hot glue for this, but you can also use silicone, acrylic or similar…
Hello friends from all over the world :) This is my contribution to the cookie cutter contest. In Germany, in the winter time there is this gingerbread mix, called “Herzen, Brezeln, Sterne" available in every grocery store. With these…
A simple way to make a DIY candle with scrap wax from old candles, a way to create your own Christmas candle and to recycle old candles Print no supports 10-15% infill is enought print 1 clip-holder , 2 body pieces (2 identical halfs), 4…
This set for making concrete clock contains: Mold for the base part Part to shape the space for the clock mechanism in the back side All three clock hands In addition you will need: Quartz Sangtai 6168s clock mechanism (…
Mold for adding variety to snowball fights
i always wanted to make a prank spoon madel out of gallium so i finaly made a mold to make one
A fun way to recycle those old and broken crayons you've got stuffed in some bin. Each train needs a bit less than 1.4 inches of crayon (standard diameter) - not counting what stays in the melting pot or cup. Prep: Print both halves (STLs…
Nachdem ich ein originalen Y Frame für meinen FYSETEC Drucker habe, musste ich einen remix au
Soap Mold : Hitchhiker's Guide to the Galaxy Feel Free to delete the positive projection. USE TPU.. The mold needs to be flexible. (Gcode is set ot pla) so slice it yourself.
This solves a problem with the MMU3's “injection molded spool holders” which are, in my opinion, inherently unstable . Due to the complexity of the five-spool setup and multiple moving/unconstrained parts, the spools have a tendency to…
These two flower pots were made for each other. You can print the pots themselves, or you can print the molds. If you print the molds, use a flexible material or a material you can make pliable enough to pull out the casted pot. I casted…
Two-part mold for creating wax candles that look like a bottle. Weight of mold and string holder - 55g . Volume of wax needed is ~ 50 cubic centimeters (cm3) . It can be printed without support; there are 4 pins for easy connection. Use…
This is a model of a sand mold that I made with a six point star. Pretty much any print settings should work. I used organic supports to help reduce the amount of filament that is used.
This easy and great project is perfect if you want something fun to do! Just print the model and use some type of separater like silicone spray to lubricate the insides. Use two M3x20 screws and nuts to fasten the two sides together. Then…
English: This is a template for getting moldings around doors and windows straight. You place the template in a corner of the frame, then put a line. You then get an equal measurement point for cutting your lists and they will fit when…
More idea than real functional model. I have no printer so it is not tested. If somebody could try that it would make me happy. It is designed for 20pcs EU beer box - 0,5l one bottle. One ice block will chill 4 beers. For full box you…
This connects to a 1 ½" barbed PVC input as shown in the picture. Our research group has put fabric, other silicone types (like putting a 10 Shore A strip in a 30 Shore A arm), and even sensors into these arms. We use Dragon Skin 10 or…
The file is of the teeth or claws that are part of the base mold for the gearshift hood frame of some models of Fiat Palio cars. As these are older models, this part is difficult to find or too expensive for my liking. And this part is…
Print 2 sides, rubber band together, fill with silicone, you can make incense cone molds!
A 50mm tall, 250mm diameter segmented circle with lap joints. This was made for pouring tools for telescope mirror making, with a filleted edge so it can be set against the mirror in question to produce a matched curve. Print 4 of these…
Mold for casting concrete cigar ashtray I made a second mold with 5mm walls to reduce the size. I also included the mold positive in case you need to make a mold from the original.
Sadly I was a bit too late for the contest, but anyway… This is a simple mold that creates the shape of a treasure chest peeking out of the sand. If you want to, you can mark the spot with a big X :-)
A mold for tree shaped wasp nests candy. Print as stands without supports. 2x tree 1x tree_bottom
A mold to clamp a freshly 3D printed front mudguard, such as the stylish one from here! https://www.thingiverse.com/thing:4317969 If you are quick in transferring a finished and heated/flexible PETG flat mudguard to the mold, it will fit…
In these stl files is all you need to 3D print a 3D benchy sand mold. Have fun :) You can either use just one part to create something like a 2D image of the benchy, or you can use both to create the 3D model. This is however not as easy.
luego de quemas mi placa e no quise desecharla, asique decidí darle un uso decorativosp32
Molds to make training models of following items: Health Post Health Center Hospital Temporary structure Office Tent Car Manufacturing instructions: Material: PLA 3D Printer: FDM 3D printer, average print time 16 hours. (with MK4 input…
Mold for making PU crutch tip. Tube 23-23mm. With large washer inside
I like to freeze CostCo chicken breast, and I was looking for a way to stop the packets from sliding around when i rummage in the freezer. Stacking the breast packets between these plates before freezing creates indentations that allows…
These cups were modeled and tested for correctness, so cooking measurements should be accurate. The intent is to quickly be able to make sand molds for casting in aluminum, copper, or brass.
This mold helps you make snow ducks easily. MAKE A ARMY OF DUCKSS!!!!! 🦆🦆🦆🦆🦆🦆🦆🦆🦆
Statue of Dr. Smolder Bravestone / Dwayne (The Rock) Johnson from Jumanji: Welcome to the Jungle. I tried to capture every detail and that's why it's probably my shortest project in one piece. Specially designed for the Prusaprinters…
It's a mold for making mini snowmans from snow. The mold is assembled from three parts. Two mold parts and one joint. Print in place version also available (I didn't print this version so if you will try, please let me know in the…
Fishing lure mold for rubber lures 6mm cutout for eyes 12cm fish
I used the moai candle mold from the source, increased the size to get a proper candle and reduced the amount of plastic around the model. Now it uses way less plastic and prints faster. Print it laying down as in the title image.
Project video: If you are an engineer, chances are you have a 3d-printer and are aware of injection molding machines, maybe even directly or indirectly working with them. So why not combine these two things? What you get , is a miniature…
A basic bath bomb mold design. I'm posting multiple sizes because if you scale it past 80%-120% you will find the tolerances are no good, also the labels on the bottom help identify them when you're like me and have too many molds around!…
I wanted a small, simple shaped concrete planter and I was inspired by some great 3d printed planter mold designs out there. This was modeled from scratch and prints without supports. I've reused the same mold multiple times without…
Hello, This is my contribution to a 3D printable leather wet molding system. I took a lot of the design queues from the readily purchasable www.BuckleGuy.com wet molds, but they didn't offer the sizes and variety I wanted. I'm a better 3D…
Made a candle for valentine's day or just for fun! You can scale the molt in „z“ as large as you need. Print instructions Print with ABS( liquid wax has about 50°C)!
If you create BambuSlicer profiles feel free to add them here: https://makerworld.com/en/models/221534 I designed a flower pot with a separate lower half to collect excess water. The parts can be printed in different materials and mixed…
A fun and easy-to-use sand mold of a paw print, which includes convenient handles on each side to make it easy to release the sand when used. The model is just under 18 cm in width, allowing it to fit even on smaller print beds (such as a…
Moldes de letras cortantes para manualidades, repostería, etc. Cutting letter molds for handicrafts, baking, etc.
Default size is checked and tested. It's safe if you want to print size bigger, but smaller please check the wall thickness before printing. Instruction video:
They can be assembled with binder clips to form different sizes of rectangle and different sizes of squares by different combinations for different size molds. Can be stacked to make taller mold.
Easy fishing form / mold for 16cm fish 6mm screw holes 8mm cutout for eyes Enjoy
Produces two different sizes of candles. Molds should be resizable to your need (however not tested): Small candle (80cm(h) x 40cm(d)): Material required: ca. 85 gr of wax, 14cm string (ca. d=1,8mm). Colors and scents are optional. Big…
Dr Smolder - Glasses Holder (or just his head as sculpture) If you like it --> press like it :-) I remixed the model Dr. Smolder Bravestone - Dwayne Johnson which was designed by 14JS-studio . There are two variants, one which is only the…
Modular Concrete Hydroponic Tower - Spiral Mold System (BETA) ❤ Support the Creator / A Special Request If you love this design and want to see more ambitious and complex projects like this come to life, please consider purchasing the…
This is a mold for snowballs to make it look like a nuke. It is a quick and easy print-in-place print at 1 hour and 45 minutes on Bambu labs p1s with no supports. print settings/info filament: 45ish grams when printed with 3 walls and 15%…
It's recommended to use 8.5～8.6g of PLA. After the molten plastic is placed into the mold, apply pressure for 15 seconds, let it sit for 1 minute, and then apply pressure again for another 15 seconds. ] This is a mold for making dice by…
A set of cloud bath bomb molds with a flat bottom for adding embeds. Free to print for your own personal use! If you just want to buy this mold, I have it for sale here: https://chunkadust.com/products/cloud-bath-bomb-mold If you'd like…
We had problems with coffee grounds molding in the container of our coffee machine. There are other sieves out there, but they are all too loose or/and the grid is too wide, allowing coffee to fall through and also mold. If you're facing…
3D printable mold to pour silicone 9cm Westin clones YOURSELF! No supports needed. Would recommend ABS/ASA at the minimum to ensure quality pouring without destroying the mold. You can print either the master itself to make your own mold…
Huge collection of children's molds Suitable for imprinting and learning about different shapes 30 designs on various themes- fruits, vegetables, animals, shapes, sweets ,numbers Print in place Easy print Added Measuring Cup for mass…
Donut bath bomb mold. Free to print for your personal own use! If you just want to buy this mold, I have it for sale here: https://chunkadust.com/products/donut-bath-bomb-mold If you'd like to sell physical copies of this file you can…
STL files to 3D print mold components and PDF files for patterns to make a Medium multitool sheath (patterned to a Leatherman Fuse - also fits a Wingman with clip attached). Finished inside dimensions are: - Medium Multitool 4 x 1.3 x .7”…
After watching my nephew attempt to build his own race track for his hot wheel monster truck at the beach, I decided to help him out with a few designs to make his own track. 180 Bank Ramp/Jump Rumble Bumps Haven't been able to test on…
Rock mold made for the H0 railway models, the best way is to print it with flexible filament. See more at: https://blog.prusaprinters.org/3d-printed-railway-models-part-iii-the-final-model/
This model is compatible with the lego system.
I think it is a nice candle mold. Since it is symmetrical, it will be enough to make the same object twice and combine it. Since my English is Google Translated, there may be spelling errors. I recommend you to use ABS in printing
This mold is based on CNC Kitchens. Watch his video for complete instructions. Standard E3D Socks can be used as well, but they will sit loose. Socks from this mold instead will have a perfect fit. There is a topic in the Prusa Forum for…
Hi! This is a candle mould I created (with fusion 360) from a penguin model ( https://www.thingiverse.com/thing:2225793 ). The result is beautiful! The mould is composed of 3 parts. The front and the back are made of PLA while the middle…
This is a two part mold for making a candle, bar of soap, chocolate bars, or whatever you want to make to look like Han Solo in Carbonite. I made one version with detailed sides which will work if you print in some flexible filament like…
easy print fishing lure mold. have fun.
Easy mold for your lure have a nice day by water Enjoy
Heard from the original designer Paul Ducarme (@PaulDucarme_3415198), he has official files posted on his own site, suggest everyone go check those out rather than my reverse engineered ones, probably improve your chances at making…
This spiral design is inspired by other pots online, and the casting idea is based off a YouTube video I saw. You can print the pot itself and use it as is. If you want to cast this out of concrete or plaster, then you need to print out…
Square flower pot concrete form mold
CANNIBAL SHAD FISHING LURE MOLD for making your own lures from plastisol. I made this one from BASF PLA ULTRAFUSE. It turned out great, I used 0.1mm layer for finest surface finish and printed on my MK4.
The first thing on my list for this year is done! Butter Chicken! 0.12 Layer height If you want to recreate it: Watch the video. Have the butter at room temp. Use plastic wrap! Press it in. Into the freezer for a while. If it has some…
This mold can be used to cast an owl out of (bees)wax. Material required: This printed mold Something to clamp the mold together Pot the heat the water Container to melt the wax in Something to measure the wax temperature 200g of wax…
a fishing lure mold to make them at home
here we have a system to build a mold in any size you need useful if you want to cast something out of resin, create a mold out of silicone, or play with kinect sand or whatever you can think of the elements have small guides to ensure a…
