Wyniki wyszukiwania: nr200

Sortowanie

Liczymy pasujące modele…

P
PrintablesCMF

NR200P ATX PSU Mount

A mount to allow an ATX PSU to be used in the NR200P case. This holds the power supply at the front of the case in front of the graphics card with space to allow the front panel IO cables through. It's based on the one you can download…

Wydruk około 5,52 €–6,74 € nettoWstępna wycena jednego wariantu

Pobrania
174
Polubienia
20
Ocena
5
P
PrintablesMikkel

CoolerMaster NR200 GPU fan shroud

This fan shroud was created to redirect air into the radiator of vertically mounted GPUs in the Cooler Master NR200(P) case. Created to fit any 120mm fan. Baseplate can be shrinked for added clearance. Countersunk screw holes created to…

Wydruk około 7,16 €–8,75 € nettoWstępna wycena jednego wariantu

Pobrania
132
Polubienia
44
Ocena
0
P
Printables...No...Name...

NR200&NR200P Side panel 5mm clip extension for Noctua D15

A 10mm shortened version from Zocazol. Slightly beveled + reduced hole for better fixing of the side. I did this for my Noctua D15 which fits just right. The lower extension brackets are not needed, stick to the original bracket. If you…

Wydruk około 0,37 €–0,45 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
92
Polubienia
14
Ocena
0
P
PrintablesCooler Master

ATX POWER SUPPLY BRACKET - MasterBox NR200 & MasterBox NR200P - Official

Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P . The design of the bracket is ventilated for actively cooled units to be installed, independently from the orientation of the intake fan. The bracket is also compatible…

Pobrania
1735
Polubienia
109
Ocena
5
P
PrintablesJJ

NR200 PSU intake duct

This model snaps into the hole behind the power supply in the NR200 case through which the power supply intakes air. Normally there is a gap between the PSU and the ventilated side panel of the case, which allows the PSU to intake warm…

Pobrania
775
Polubienia
122
Ocena
5
P
PrintablesCooler Master

Panels clips replacement - MasterBox NR200 & MasterBox NR200P - Official

Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P . We are making free to print and modify the design for the clips that hold the paneling of our most beloved ITX enclosure(s)! Lost one? Your product is out of warranty?…

Pobrania
655
Polubienia
68
Ocena
5
P
PrintablesCooler Master

Top Panel replacement - MasterBox NR200 & MasterBox NR200P - Official

Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P . We are making free to download, remix and modify the design of the top panel of our most beloved ITX enclosure(s)! You can easily modify it to add support for a…

Pobrania
620
Polubienia
100
Ocena
0
P
PrintablesZocazola

NR200 Side panel 15mm extension (SEMI-OPEN AIR DESIGN)

This is a work in progress for the NR200- adding a side panel extension that's 3D printable to allow for taller CPU coolers like the NH-D15. Currently my designed clips hold the side panel 15mm out from the side (extending the 153-155mm…

Pobrania
578
Polubienia
35
Ocena
4
P
PrintablesZocazola

CoolerMaster NR200 top-mounted radiator bracket

Summary of the T240R- Top 240 mm Radiator mount for the Coolermaster NR200 ITX case. This is a mounting assembly/system mod for the Coolermaster NR200 to mount a full size 240mm radiator with 2 120mm fans to the top of the NR200. This mod…

Pobrania
513
Polubienia
42
Ocena
3
P
PrintablesErer2001

NR200/NR200P PC case raised U shape feet

3 shell, iron the top surface for better look. Very easy to print.

Pobrania
464
Polubienia
70
Ocena
4,8
P
Printablesivtue

NR200 Controller Holder

Model slots into the front panel. This has only been tested with the 8Bitdo Ultimate C and Switch Pro controller but comment if it works with others. Revision History: 2023-08-01 R0: Initial release 2023-09-04 R1: Fixed orientation to…

Pobrania
398
Polubienia
51
Ocena
4,75
P
PrintablesPK

NR200 15 mm Slim Fan Mounting Pins

Mount slim fans on top of Cooler Master NR200P case. I wanted my PSU to hang higher inside the case to help with cable management, however that caused the power plug to collide with the stock 25 mm thick fans. So I made this to install…

Pobrania
372
Polubienia
32
Ocena
5
P
PrintablesFourMadrone

240mm to 280mm Adapter - Cooler Master NR200

I wanted to make use of all the space available on the bottom of my NR200, so I made this adapter to fit two 140mm fans instead of having two 120mm fans and some unused space. I made this 9.5mm high in order to fit the adapter and fans…

Pobrania
350
Polubienia
35
Ocena
5
P
Printablesjohanncc

Snapfit NR200 PCIe slot covers

Designed these PCIe slot covers for the NR200 to give the CPU cooler a bit more air, also they snapfit ! Note The covers are dimensioned using ABS which shrinks a bit more than other plastics, so if it's too loose for you, try scaling the…

Pobrania
312
Polubienia
64
Ocena
5
P
PrintablesCooler Master

Original Feet Replacement - MasterBox NR200 & MasterBox NR200P - Official

During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…

Pobrania
306
Polubienia
34
Ocena
0
P
Printablesilluminati

NR200(P) tall feet

NR200(P) tall feet with two additional screw holes to the original design. Benefits Better airflow Easier filter clean-up Easier table clean-up More robust attachment to the bottom plate due to the added screw hole Printing Infill: 25% No…

Pobrania
303
Polubienia
15
Ocena
0
P
PrintablesDasBooty

NR200 Mac-Grater Front Panel

NR200 Mac-Grater Front Panel

Pobrania
286
Polubienia
69
Ocena
0
P
Printablesjohanncc

NR200 x MSI Ventus deshroud mod (Noctua NF Series Version)

TLDR Deshroud mod for the MSI Ventus 3080/3080Ti/3090 in the Cooler M case Fan shrouds designed to perfectly fit the Noctua NF-A/F/S12 and bridge the gap between the fan and the GPU heatsink 2 Versions available for use with & without…

Pobrania
250
Polubienia
26
Ocena
0
P
PrintablesMark

NR200p Dual 120mm Fan Front Panel

Wanted a bit more airflow for my NR200p dual rad water-cooled setup so cut out some of the excess behind the front panel and replaced it with this. Its a big model, just about filled the bed on my Voron 2.4's 30cm build plate. Needs 8 M3…

Pobrania
223
Polubienia
21
Ocena
0
P
PrintablesJJ

NR200 lift kit for 25mm fans

I've glued, sanded and painted the bottom in the photo, which is why the join line and layer lines are mostly hidden. The original model by tangcla is on Thingiverse, but I reuploaded it here with permission so it can be added to my NR200…

Pobrania
221
Polubienia
49
Ocena
4,67
P
PrintablesPliind

Cooler Master NR200P Extension Frame

Frame will give you another 9mm of width. Frame V2.0 (TG and metal and radiator mount compatible) 7-part print. Radiator spacings fixed, they are now precise. Also made holes 4mm big to accomodate Deson m3 screw inserts in radiator mount…

Pobrania
219
Polubienia
32
Ocena
5
P
PrintablesCooler Master

Round, low-profile Feet Replacement - MasterBox NR200 & MasterBox NR200P - Official

During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…

Pobrania
203
Polubienia
32
Ocena
5
P
PrintablesScout339

NR200P ATX PSU Mount - Optimised

"A mount to allow an ATX PSU to be used in the NR200P case. This holds the power supply at the front of the case in front of the graphics card with space to allow the front panel IO cables through. It's based on the one you can download…

Pobrania
202
Polubienia
10
Ocena
0
P
PrintablesAP1980

Cooler Master NR200P TOP-Extension for AIO-Mounting

Designed to mount an NZXT Kraken X63 (280mm AIO) on top of the NR200P. Glass and Mesh-Panels still can be used, also standard top cover fits perfectly in. All Connectors should be printed with PETG with min. 25% infill. Material of…

Pobrania
196
Polubienia
22
Ocena
0
P
Printableschimy

XBOX Controller Hanger for NR200

Simple XBOX controller hanger for side of NR200/NR200P

Pobrania
191
Polubienia
23
Ocena
5
P
Printablespilniczek

NR200P feet pairs

Twice as high as original version

Pobrania
185
Polubienia
28
Ocena
3
P
Printablesunknow1assassin

Snapfit NR200 PCIe Slot Covers (Reinforced)

This is a remixed model based on the Snapfit NR200 PCIe Slot Covers, designed to snap onto the back of the case where the vertical GPU support is located. The updated model is more precise in terms of its size and features reinforcement…

Pobrania
184
Polubienia
24
Ocena
5
P
Printablesunknow1assassin

Absolut Airflow for NR200 (Basic Version)

Basically, this is a relatively easy mod that drops both CPU and GPU temperatures while running the fans at lower speeds which also resulting in much less noise. It is specially optimized for Noctua NF-A12x25 fans and FDM printers. To get…

Pobrania
160
Polubienia
26
Ocena
5
P
PrintablesBeastie

NR200P Back Panel Mod

This is a 3d printable back panel made for the Cooler Master NR200P to allow for a vertical-mounted GPU and a top-mounted AIO. The printed mod changes the position of the motherboard down 26.5mm, GPU down ~63.5mm, and moves the internal…

Pobrania
152
Polubienia
27
Ocena
5
P
Printablesmichaelstickels

NR200 ATX PSU Side Mount

Edit: A new version moves the PSU up an additional 5mm inside the case. Depending on your PSU, the power cord might interfere with the top panel. A custom designed remake of the ATX PSU bracket for the NR200 and NR200P that relocates it…

Pobrania
151
Polubienia
10
Ocena
5
P
PrintablesCooler Master

Squared/Tapered Feet Replacement - MasterBox NR200 & MasterBox NR200P - Official

During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…

Pobrania
150
Polubienia
18
Ocena
0
P
PrintablesCooler Master

Angled Feet Replacement - MasterBox NR200 & MasterBox NR200P - Official

During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…

Pobrania
140
Polubienia
28
Ocena
0
P
PrintablesCeriphim

Cooler Master NR200 Top Panel Cover

masterThis is a top cover intended to replace the mesh of the top panel on the Cooler Master NR200 PC case. The cover leaves cutouts for the top fans (intended for use with fan grills via my external mounting hardware at…

Pobrania
133
Polubienia
20
Ocena
0
P
Printableswebhdx

HP EliteDesk 800 G3 SFF motherboard bracket for CoolerMaster NR200 NR200P

A bracket for HP EliteDesk 800 G3 SFF motherboard for mounting in Cooler Master NR200 NR200P cases. It's likely you can also use it for mounting inside other mATX and ATX cases but I have not tried it myself. This is a low effort model,…

Pobrania
127
Polubienia
16
Ocena
5
P
PrintablesLukaku

Cable Cover PSU (Coolermaster NR200)

Hide the cables on the left, right and under the PSU. Simply apply some VHB adhesive tape to the back in the area without holes (bottom) and stick it on. Quickly attached - quickly removed again. Tested with an RTX 3090 (approx. 3mm gap…

Pobrania
122
Polubienia
37
Ocena
0
P
Printableskubajabko

Cooler Master NR200 Power button cover

Cover designed to stick into NR200's USB ports. Main purpose is to prevent cats from turning off your PC while gaming :)

Pobrania
120
Polubienia
9
Ocena
5
P
Printablesjohanncc

NR200 x MSI Ventus deshroud mod (Arctic P12 Version)

TLDR Deshroud mod for the Ventus 3080/3080Ti/3090 in the Cooler Master NR200 case Fan shrouds designed to perfectly fit the Arctic P12 and bridge the gap between the fan and the GPU heatsink The Normal Fan Screws version of the fanshrouds…

Pobrania
117
Polubienia
16
Ocena
0
P
PrintablesJerry Wzc

NR200 PSU Cable Cover (Screw down)

A revised version of Lukaku's NR200 PSU cable cover: https://www.printables.com/model/659461-cable-cover-psu-coolermaster-nr200. Added screw holes at the top so the part can be screwed in place with existing screws on the PSU bracket…

Pobrania
112
Polubienia
14
Ocena
0
P
Printablesjohanncc

NR200 x MSI Ventus deshroud mod (Generic 120mm Fan Version)

TLDR Deshroud mod for the MSI Ventus 3080/3080Ti/3090 in the Coolermaster NR200 case Fan shrouds designed to fit any standard 120mm x 25mm computer fans and bridge the gap between the fan and the GPU heatsink Fan shrouds can be mounted to…

Pobrania
106
Polubienia
12
Ocena
0
P
Printablesgrumblegore

NR200 - SFX-L raised PSU mount - spartan

I bought an AMD Radeon 6950 which barely fits in the NR200. With the stock PSU bracket, the cables physically push the already heavy GPU down, and no matter how hard you fold and press the cables against the PSU, you will never see…

Pobrania
105
Polubienia
4
Ocena
0
P
Printablesmichaelstickels

NR200 Dual 3.5" HDD Side Mount

A custom designed mountain bracket for fitting two 3.5" HDDs on the side mount of the Cooler Master NR200 (or NR200P) instead of one. The bracket attaches using the included #6-32 case screws and will work with all standard 3.5" drives.…

Pobrania
105
Polubienia
12
Ocena
0
P
PrintablesCooler Master

"Pill" Feet Replacement - MasterBox NR200 & MasterBox NR200P - Official

During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…

Pobrania
104
Polubienia
18
Ocena
0
P
Printablesupdawg

NR200 / NR200P Extended Clip

Print in PETG as you will run into reliability issues with PLA.

Pobrania
103
Polubienia
8
Ocena
0
P
Printablesmbard35

NR200 Vertical 3.5" HDD Adapter Plate with custom offset for GPU clearance

Features an offset so that a standard 3.5" HDD ends up sitting 17mm left and 10mm up relative to the original plate. This is to make more space for cables or fan hubs mounted to the right of the HDD on the inside “wall” of the front…

Pobrania
101
Polubienia
15
Ocena
5
P
Printablestangcla

Cooler Master NR200P Fan Riser Feet for 25mm fans

I took DROUGA's design and simply added 10mm to the height so that standard 25mm fans will fit. Category: Computer

Pobrania
98
Polubienia
9
Ocena
0
P
Printableshashcollision

NR200 Vertical HDD Adapter Plate

The default orientation for a 3.5inch HDD in the NR200 puts the connectors right next to the CPU fan and above the 24 pin, USB3, SATA, etc on most motherboards. This is very crowded and I had to bend my SATA power cable a concerning…

Pobrania
95
Polubienia
8
Ocena
0
P
PrintablesCeriphim

NR200 Hardware for Top Panel External Fan Grills

I didn't want the included mesh top panel to restrict exhaust airflow so much, so I made this Cooler Master NR200/p top panel hardware to allow external fan grills to be installed to the top of the case when the mesh is removed. This can…

Pobrania
95
Polubienia
9
Ocena
0
P
PrintablesDaniel Byhlin

NR200/NR200P ATX bracket

Bracket to mount an ATX power supply in the Coolermaster NR200/NR200P. This only works if you have already inverted the case. The two “pegs” slide in under the little sheet metal edge in the front, and the bracket then screws to the…

Pobrania
94
Polubienia
20
Ocena
0
P
PrintablesCooler Master

Cone Feet Replacement - MasterBox NR200 & MasterBox NR200P - Official

During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…

Pobrania
93
Polubienia
19
Ocena
0
P
Printables3DCatt

Cooler Master NR200 ATX power supply bracket

This can be printed without supports at 0.3mm, if you dont care the line look

Pobrania
92
Polubienia
10
Ocena
0
P
PrintablesJJ

NR200 replacement rubber feet

I stuck mine on with double sided tape, but glue should work too.

Pobrania
91
Polubienia
12
Ocena
5
P
Printableskitlaan

NR200 USB-C Front Panel

This part allows replacing the audio jack on the NR200 top/front panel with a USB-C port. This will require permanently modifying the top panel to expand the audio jack hole. The theory is that folks won't be using the audio jack quite as…

Pobrania
91
Polubienia
24
Ocena
0
P
Printableshugodrax

XBOX Controller Hanger for NR200 with Magnets

Remixed @chimy's XBOX Controller Hanger for NR200 model to include four 6mm x 3mm magnets. This helps hold the mount in place. Printed in PLA+ with 40% infill, works great! Please like and share, happy printing!

Pobrania
89
Polubienia
18
Ocena
5
P
PrintablesFred N

NR200 Front Panel Cover

I have a problem with cats (who for sure like the warm exhaust) turning my NR200 case on and off at the worst possible times. Threw this together to hopefully reduce the incidents of F eline P ower B utton A ctuation. I use the USB-A and…

Pobrania
87
Polubienia
15
Ocena
5
P
PrintablesDROUGA

NR200 AIO Tophat

This is a remix of naturalnetworks 'Cooler Master NR200 Case Top Hat Spacer' I would have added the remix in the proper way but Thingiverse is broken again... This tophat is designed with EK 240 D-RGB AIO in mind, with a rad thickness of…

Pobrania
86
Polubienia
10
Ocena
0
P
Printableshugodrax

NR200 Headphone Holder - 85mm Wide

This is an 85mm wide headphone/headset holder for the NR200 case with or without 6mm x 3mm magnets. I printed it in PLA+ with 60% infill and it is solid with no bending. Happy printing!

Pobrania
86
Polubienia
7
Ocena
0
P
Printablesfitandfinishlab

Cooler Master NR200P v2 atx psu mount bracket

In NR200P v2 case by default you can use sfx and sfx-l standards power supply. As you could imagine going in smaller dimensions standards is quite a bit more expensive than standard atx. However the amount of space in the case itself is…

Pobrania
77
Polubienia
7
Ocena
0
P
PrintablesDROUGA

NR200 Fan Riser Feet

Was looking to add better airflow by adding some fans in the bottom inside, but restricted for space because I am getting a triple slot GPU in the near future. So I got the idea to add slim 120x17mm fans to the outside and move the dust…

Pobrania
76
Polubienia
17
Ocena
5
P
PrintablesKC Carillo

ATX Power Supply Bracket - Very Low for NR200/P

A lower ATX PSU bracket for the NR200P to allow both top fans (25mm thick) to be installed. Will be a tight fit using the included push-pin mounting but will work. I removed one side for TG/display purposes and removed the perforations on…

Pobrania
72
Polubienia
9
Ocena
5
P
PrintablesError 702

NR200 stock leg 40 mm high

Ножки напечатаны АБС-пластиком, толщина слоя 0,1 мм, заполнение 50%. После того, как вы прикрепите ножки шурупом, просверлите в ножке отверстие для второго шурупа. Так они будут держаться крепче.

Pobrania
71
Polubienia
8
Ocena
0
P
PrintablesJeb3592

NR200 Top 3.5" Drive Mount

To mount this, you take out two of the power supply screws and put them back in through the mount to attach it to the psu shroud. Then you slide the drive in and screw it into place. Tolerances in this spot are very tight, you'll want 90…

Pobrania
69
Polubienia
9
Ocena
0
P
PrintablesJJ

NR200 bolt-on GPU support bracket

This bracket supports the GPU by bolting to the back of the GPU and the bottom of the NR200 case. I designed the bracket for my RX6800 reference, but I think it should also work for the RX6800XT, RX6900 and RX6950XT as they seem to have…

Pobrania
69
Polubienia
17
Ocena
5
P
Printablesunknow1assassin

NR200 Anti-sag Bracket (Only for Asus 30 series TUF GPUs) V2.1

This is an upgraded model designed to address the issue known as "lip," which I have noticed can vary among different models. Nevertheless, both models are now compatible. Introducing the ultimate GPU anti-sag/support bracket. All you…

Pobrania
69
Polubienia
11
Ocena
5
P
PrintablesMatyi Bejó

Headphone hanger for NR200(P)

A simple way to store your headphone on the cooler master nr200p case

Pobrania
67
Polubienia
5
Ocena
0
P
PrintablesDoronzo

CoolerMaster MasterBox NR200 3.5 HDD Drive Mount

Yet another HDD Mount for the NR200. This version allows you to have both a top slim fan and a full length GPU. this one also has extra space between the model and the adapter to allow better air flow. I've used Noctua's a12x15 as a top…

Pobrania
66
Polubienia
4
Ocena
0
P
Printablesionstream

NR200 tool-less top mount for slim fans (15mm)

A tool-less fan mount peg for slim 15mm thick fans on the Cooler Master NR200 case. The original fan mounts were designed with regular 25mm thick fans, which meant that 15mm fans would dangle loose. I added flat sides to the peg to…

Pobrania
65
Polubienia
9
Ocena
0
P
Printablespoloon

Cooler Master NR200 Headset Holder with 4 USB holder

simple headset holder with four USB holder for Cooler master NR200 casing

Pobrania
64
Polubienia
10
Ocena
5
P
PrintablesRobert

raised NR200 top panel

slightly different for a few millimeters of extra clearance

Pobrania
63
Polubienia
4
Ocena
0
P
PrintablesLorinthu

NR200 Simple Power Button Cover

Simple cover to protect the NR200 power button from being accidentally pressed

Pobrania
63
Polubienia
2
Ocena
0
P
Printablesjk752

PC Desk Mount (For CoolerMaster NR200)

Brackets to mount your PC to your desk I wanted a visually cleaner workspace so I wanted to mount my PC to the underside of my standing desk (before it was sitting on top) This is specifically for the CoolerMaster NR200 case (when laid on…

Pobrania
62
Polubienia
14
Ocena
5
P
Printablesmonokeith

NR200P bottom exhaust air guide

Intended to be used for Cooler Master NR200P bottom exhaust, it guides hot air to exhaust to one side of the case, so it doesn't heat up my hands and keyboard. I printed this with PETG filament, as the exhaust can get quite hot. Not sure…

Pobrania
61
Polubienia
13
Ocena
0
P
Printablesmichaelstickels

NR200 Long Fan Pin for Phanteks Halo RGB

Slightly longer fan mounting pin for NR200 top panel to allow for installation of Phanteks Halo RGB addons to the fans. I could not make holes for the original fan grilles to screw into as the walls of the pin would have been too thin for…

Pobrania
60
Polubienia
9
Ocena
0
P
PrintablesKarolNI

Cooler Master MasterBox NR200 inverted mod - front IO mount

To invert the case u have to just filp it upsidedown, swap top and bottom panel. This mod involves permament change to the case, you have to cut off 3 threded standoffs. The front panel isn't perfectly symetrical, so after the mod you end…

Pobrania
57
Polubienia
8
Ocena
0
P
Printablesaitidina

NR200 top and bottom radiator mounts

These are the .stl files I made two years ago to build a custom water cooling loop into my current PC. For those of you familiar with the Cooler Master NR200 case, you'll know it is a nice mini-ITX case and it gives you quite much…

Pobrania
55
Polubienia
7
Ocena
0
P
PrintablesJerry Wzc

NR200 GPU Power Cable Hider

A GPU power cable cover for NR200 and NR200P ITX case.

Pobrania
55
Polubienia
7
Ocena
0
P
Printablespilniczek

NR200P PSU/HDD mount

The “--clear” version does not contain additional surface for better adhesion during print.

Pobrania
53
Polubienia
4
Ocena
0
P
PrintablesDasBooty

NR200 Wavy Front Panel

NR200 Wavy Front Panel

Pobrania
52
Polubienia
16
Ocena
0
P
PrintablesFlowkin

Coolermaster NR200/NR200p SPC vertical pump mount

So I decided to transplant my old loop with an EKWB A240G aluminium loop into an NR200p. Seeing how it is recommended to have a EK-XRES 100 SPC-60 MX PWM (incl. pump) in the vertical orientation (according to the manual). I decided to…

Pobrania
48
Polubienia
6
Ocena
0
P
PrintablesKC Carillo

NR200/P Wi-Fi Antenna mount

2 x Wi-Fi Antenna mount for the NR200/P case, Fits on the top cover mounting area to guide and uses the same hole for the screw as retainer. Requires RP-SMA extenders/pigtails with a bulkhead female end (preferrably sub-1ft to minimize…

Pobrania
48
Polubienia
8
Ocena
0
P
PrintablesTorque475

NR200 Power Button Cover

This weekend one of my cats forced my NR200 pc to shut down while she was lounging on her “cat warmer” that I call my gaming pc. So I immediately sought to remedy that by making a button cover, because I know better than to try and train…

Pobrania
48
Polubienia
5
Ocena
0
P
Printablesunknow1assassin

Universal GPU Anti-Sag for NR200 (Zip-Tie)

This is a universal anti-sag or GPU support bracket designed to work with the majority of GPUs available. No case modification is required as it can be securely attached to the HDD screw holes on the case and the GPU support holes on the…

Pobrania
47
Polubienia
6
Ocena
5
P
PrintablesAtymisk

NR200 ASUS TUF 30 Series GPU Shroud Duct

After building with in the NR200 with an ASUS TUF 3080ti, I did extensive research to see if I should add slim fans to the bottom of the case. Most results showed that it would have added turbulence and also found that a duct performed…

Pobrania
47
Polubienia
3
Ocena
0
P
PrintablesJustin

Front Panel Clip for Cooler Master NR200P

Direct replacement for the stock front panel clip

Pobrania
46
Polubienia
4
Ocena
0

nr200 chase clip

This is a clip wich hold front pannel on coolermaster nr200 PC chase. I redisign it by myself, but it looks like original on this site. In my disign no parts in the air, you can print it on a side without support. And differend oval shape…

Pobrania
44
Polubienia
2
Ocena
0
P
Printableswebhdx

HP EliteDesk 800 G3 SFF backplate for CoolerMaster NR200 NR200P

Backplate to be used with my motherboard offset plate. I recommended printing it with some higher temp resistant filament like PETG. I've used orange Prusament PETG. I personally have RX6400 GPU so there is an additional cutout for…

Pobrania
42
Polubienia
7
Ocena
0
P
PrintablesChriL

PowerColor 6900 XT Red Devil NR200 Support

Print flat side down. To install, loosen or remove screws at the far end of the GPU and at the GPU IO plate of the side case frame. install the support and reattach frame. Support me on ko-fi. Updates 2023/01/05 Removed cross beam near…

Pobrania
42
Polubienia
6
Ocena
0
P
PrintablesDanish aznita

IM01/NR200p Handle

I made this simple handle to carry my SAMA IM01. It utilizes the back 80mm fan mount UPDATE 10/8/2024: After many month of lugging my PC to and fro, the handle still held up very good . Ultimately , I went with 40mm M5 screw with 2 thick…

Pobrania
40
Polubienia
6
Ocena
5
P
PrintablesErer2001

NR200/NR200P bottom fingerprint sensor and 3.5 usb c DAC

x2 usb 2.0 breakout, x1 usb fingerprint sensor, x1 usb to usb c adapter, x1 Apple usb c DAC. The fingerprint sensor is easier to reach if the pc is on the desk top. Also Apple's cheap usb c DAC have great audio and the ADC is way better…

Pobrania
39
Polubienia
13
Ocena
0
P
Printablesavrhacks

Cooler Master NR200P Mac G5 Style Feet

Customize your Cooler Master NR200P with feet that like the Apple Mac G5 or classic Mac Pro !!

Pobrania
39
Polubienia
8
Ocena
0
P
PrintablesJJ

NR200 Scythe Mugen 5 cooler support (For ASRock X570 Phantom Gaming ITX)

This model will only work for this exact combination of case, cooler and motherboard! Any other combination will most likely change the position of the cooler in the case. Feel free to remix.

Pobrania
37
Polubienia
13
Ocena
0
P
Printableswebhdx

HP EliteDesk 800 G3 SFF PSU bracket for CoolerMaster NR200 NR200P

A bracket for mounting HP EliteDesk 800 G3 power supply inside CoolerMaster NR200/NR200P case. I don't know if this is the best placement for the PSU but I wanted to get it done as quick as possible so I took 2 models and remixed them.…

Pobrania
34
Polubienia
7
Ocena
0
P
PrintablesDenitz

DualSense NR200(P) mount

I remixed Trajan s “ Honeycomb Wall PS5 DualSense and DualSense Edge Controller Mount ” to a mount that could hold the controller at the side of a NR200(P) computer case by Cooler Master. It needs supports to be printed.

Pobrania
33
Polubienia
2
Ocena
0
P
PrintablesError 702

NR200 deshroud KFA2 RTX 3060

Printed with ABS plastic, layer height 0.1mm To remove the fan shroud on this card, you will have to completely remove the cooling system. If you cannot find a ready-made adapter for connecting fans to the power connector on the video…

Pobrania
31
Polubienia
9
Ocena
0
P
PrintablesJJ

NR200 ASRock X570 Phantom Gaming ITX 4010 M2 cooler bracket

I've inserted magnets in the bracket to snap it to the case, but I've included a solid version to tape down or add your own holes for magnets.

Pobrania
29
Polubienia
15
Ocena
0
P
PrintablesAlex Kört Lori

NR200 Vertical 3.5" HDD Adapter Plate with custom offset for GPU clearance

Remixed Model NR200 Vertical 3.5" HDD Adapter Plate with custom offset for GPU clearance My HDD has different Holes, so i redesign the Adapter with two etxra holes for screws.

Pobrania
29
Polubienia
1
Ocena
0
P
PrintablesGeezertron

CM NR200 controller/headphone holder split hooks

remix of controller holder with the hooks extended to each side with a cut in the centre.

Pobrania
28
Polubienia
3
Ocena
0
P
Printablespbouna321

NR200 Rear Cable Grill

Used to help hide the cables coming out of the back of my NR200. Sticks on with two way tape.

Pobrania
28
Polubienia
4
Ocena
0
P
PrintablesDangle

NR200P Cat Roost (Save Your Airflow!)

This is meant to fit on top of a Cooler Master NR200P desktop computer case. Printed on Bambu P1S with 0.4 noz and 0.28 layers. No supports needed. I used PetG to withstand the temps of my computer exhaust, but PLA+ would probably be…

Pobrania
28
Polubienia
26
Ocena
0
P
Printablesaeberbach

NR200 MITX case USB-C front panel mount

I got a new mainboard with a USB-C header. That's a lot more useful on the front panel than the front panel audio to me, so I got https://amzn.asia/d/h0ZvS1F and made this adapter. The NR200 has a separate PCB for the audio jacks so it is…

Pobrania
27
Polubienia
4
Ocena
0
P
Printablesns-74

NR200 Side panel 15mm extension clip

This is a extension pin and clip that allows you to use the existing factory clip and extend the side panels out by approx 15mm. This does not require you to remove the original factory clips, they push into the original clips and then…

Pobrania
27
Polubienia
1
Ocena
0