Liczymy pasujące modele…
Remix of https://www.thingiverse.com/thing:4240305. Made some edits to it to fit my liking, mainly to get an aligned outer profile and hide the cable on top. Also the front plate is mounted from the back by using M3 inserts (Turmberg3D…
My Ikea LAGKAPTEN Desk can't hold much weight in screws, but I can bracket 20mmx20mm 8020 t-slot extruded aluminum rails onto it easily with this adapter. I have 2 different sets of options in the provided STLs: The T-slot profile for…
M8 mounting hole Standard printing profile - 2 walls, 15% infill, etc No supports/brims needed
Simple and light K400 holder for my sim rig. It could fit other keyboards, i have no idea - feel free to try and let me know. It's not designed to use the keyboard on it, only to rest it while not in use. It appears to hold fine if doing…
CAD features + Footprint: Cutouts on the front and back for fingers, to make it easier to grab the gloves Small spring effect keeps gloves nicely in place Tiny edge blends to compensate for elephant's foot Designed to print in the strong…
Primarily I used this to drill holes to install screws through plywood and attach cabinets or other furniture projects.
Used a scrap piece of 8020 1530 to make a vertical rack to hold my 3 backpacks and my camera gear
Needed a lot of panel mounts and my vendor of choice was completely out of stock. Created a Fusion model and made my own. Since I could customize the slot for the nut, I didn't see any need for the extra thin 'fin' that the commercial…
Clean push-fit end cap for 45 series (45x45mm) T slot aluminum extrusion (8020-style profiles). Covers exposed ends for a finished look and keeps debris out of the slots. Friction fit, usually goes on by hand, but a few light taps with a…
Used to attach an Atolla 7-port USB hub to the end of racing sim pedal deck The USB hub is here: https://a.co/d/0zsirkj Used M4 t-nuts Parts were measured to fit on either end of the hub as shown in the photo.
Колпачок для спидометра ГАЗ, Cap for GAZ speedometer
V3 UPDATE 11/12/24: Added reinforcement across the whole lip. ------------------------------------------------------------------------------------------- V2 UPDATE 25/10/24: Due to excessive clatter on the 8020 profile, I've added a…
Pretty quick print for holding a 5/16" nut in some extruded aluminum. The one caveat is that you need to use low-profile nuts rather than the nuts from the “just take a handful and we will weigh them to give you a price” bin, which are…
Allows for mounting an Aurasound or Dayton Audio bass shaker on extruded aluminum. My shakers have holes for M5 bolts, and I used M5 heat set inserts to hold them in place to the mount. I've included STLs for both M5 and M4 shaker mounts,…
To mount the Fanatec 1.5 Shifter and one cheap Handbrake from Aliexpress to a Simrig based on alu profiles.
M8 mounting hole Standard printing profile - 2 walls, 15% infill, etc No supports/brims needed
Mount for Fanatec DD PSU to tidy up a sim rig. Slide from an extremity of the alu profile; no fasterner needed. Easy removal of the PSU as it is not hold tight - only suitable for horizontal mount of the PSU. Easy print in PLA with 15%…
Wanted a hinge to put on my sim rig, to allow my keyboard tray to move away while playing. This won't hold much load, for obvious reason, but it serves me greatly. No supports needed for printing. You'll only need a partially threaded…
Simple and light K400 holder for my sim rig. It could fit other keyboards, i have no idea - feel free to try and let me know. It's not designed to use the keyboard on it, only to rest it while not in use. It appears to hold fine if doing…
Battery holder for Heltec case (battery type 802040) Snaps right into place! Tutorial: 1. Insert the battery into the holder with the battery cable sticking out of the hole 2. Connect the battery cable to the Heltec battery connector 3.…
Two piece handle for Series 40/15 (40mm / 1.5in) Aluminum Extrusion Included step file incase you need to make changes. I printed it upright, and on the side. And I think the side comes out better. I used tree supports and a brim when…
I couldn’t find a secure mounting point for cables on my 8020 cnc frame, so i designed these to drop in and twist to lock in place. printed at .2layer height using petg, but asa, abs, pc, etc would work as well.
This is for tall versions of the e-stop (~7mm taller than shorter variants). Fabio's “ Torque off E-stop Button Simucube 2 Pro Cover ” wasn't suitable for my emergency stop due to variations in some Simucube components from different…
This is a simple jig for making mechanical 90 degree joints with either 15 or 10 series 8020 extrusions. You can drill these out for a metal insert, or for just a couple uses use it as is, just make sure if you plan to do this that you…
This is a remix of Looking4's Pimax wall hanger from YouMagine. I've modified the model to allow it to be mounted to an 8020 extruded aluminum sim racing rig chassis, as a convenient place to hang your HMD once you're finished racing. It…
I printed these to mount my Saitek X52 to my sim rig. Bolt the hotas mount to a piece of 40x40 profile to fit the length you need. Choose mount type and bolt to rig. When it's time to fly just drop the profile in place with your hotas…
Changelog: 2026-06-08 updated to v0.2. adjusted depression for battery door. Accidentally had m6x16 in BOM which should be m6x20mm. I added a m6x16 version for m575. 2026-06-08 added beta logitech m575 mount based on…
Print all parts following the instructions noted on each file, only one copy of each file is needed. Assembly: Cut the filter to size, you can use the filter cover as a guide. Place the 2 M5 bolts on the sides of the fan case, where the…
Paired one of these panels (https://www.amazon.com/gp/product/B01KZLM3QC) with a webcam "suspension boom" (https://www.amazon.com/gp/product/B07BLQF41P) to make a light for my desk. I can't use the original table clamp on my current desk,…
8020 Pimax VR headset holder The model was printed with supports on the bottom, however you can offset the model to remove the guide pins and print on a flat surface. If you have support interface material though, its the way to go as the…
Not everyone wants a circular version, here we get more real estate
Mouse holder / pad designed for GTOmega Prime sim rig. Designed to use GTOmega screws, they sit flush with holder surface. There is a bit of flex due to length but not noticeable when in use. Length of pad is the same as GTOmega…
I have provided a ready to print .3mf file. I have printed this in Bambu Matte Red and Sunlu Matte Olive Green successfuly. The improved shaft design was modeled in Blender however the new bolt pattern was done in the slicer.…
As part of a project I undertook to DIY (design-it-yourself) a modular EggBot-style robot from scratch using some parts I had on hand, I decided to use T-slot 8020-style profile as my base to allow for adjustments. Two issues were…
Replacement blades, in the style of the T33. I'm not sure about the size of the hub at all.
This is a jig for positioning of holes for Anchor Fasteners in 1 inch extruded aluminum t-slot, commonly called 8020. The borehole should use a 9/16th End Mill or high quality Forstner bit.
I made these twist-in panel mounts for installing overlay panels. The hole supports a Heat-Set Inserts, 5/16"-18 Thread Size, 1/2" Installed Length (McMaster part# 97171A260) One model is without a hole to enable one to create the hole…
Bolts in place securely with 4080, 1.5x3”, 3x3”, or 8080 aluminum profiles. Printed from PLA With no support. .2 LH.
Jig is for overlay panel that completely cover the 8020 profile. Hole is sized for a 5/16" bolt. Print with several wall layers (I used 5) or solid.
This is a Remix from Kelvin Lee's MOZA R9 PSU Mount. I don't own a R9 base but I have MOZA's AB9 FFB Base that came with what I would think it's the same power supply. However, the 4 small feet underneath the PSU hit the vertical…
Print this part horizontally to maximize strength. Works best with one on each corner. I did not make provision to fasten the extrusions together, which likely limits their utility to leg extensions in compression.
This is a replacement switch cover blank. It's a file ready for you to modify and add your own features.
Mount your AOC power bricks(any brick that is ~138mmx68mmx24mm would fit) to any rail that has tnuts. Bolt holes accept M5 or M6 shoulder head screws. Use wonderful tree supports for the small overhangs. Enjoy if it helps you I'm glad!
Replacement part for the Philips MSX VG-8020 keyboard clip. This piece often breaks when opening the case of this vinta
Allows mounting of a 3/16 panel to 8020. Needs a ¼-20 1" Cap Head Screw, and uses standard 8020 tnut, drop in, or low cost.
Mounts a nema23 stepper to an 8020 profile. Designed for my custom CNC design.
Fanatec shifter knob holder - on 8020 profil rig. Perfect for Sim-lab, Simxpro, TrakRacer rigs
I wanted a way to mount my Philips Hue Play Bar above me for use while gaming. I have a Sim Lab quad monitor mount and decided to mount them to the tops of the uprights. Came up with this design and it is working great! Clip end simply…
I wanted to mount my elgato key light air lights above my genelec audio monitors, which are on a VESA arm next to my monitor. So I designed spacers (you need to print 2) for the bottom and an extension arm that gets mounted to the top two…
This is a wire organizer that snaps on to 8020 1515 extruded aluminum (I have only used it with printed 8020 1515 parts, but it will surely fit the actual aluminum material also). I am using it to hold servo leads and 22-28 gauge wires…
The primary mirror mount on an 8020 series 10 beam. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: inland pla Category: Physics & Astronomy
🧾 Required Hardware (not included) You’ll need: 1× M8 screw (length depends on your profile, ~16–20 mm works for most rigs) 1× M8 T-nut for your aluminum profile slot Everything else is 3D printed in a single piece. 🧩 How to use Print the…
A mount for an iPhone in a case for an 8020 series 10 extrusion. You will need one 4.5 in 1/4-20 hex head bolt and one 1/4-20 nut. You will also need two t-nuts and screws to attach the mount to an extrusion. Category: Camera
It's designed to use both holes on a 8040 extrusion profile but if you want to use it on something bigger it should work without any issuest too. No need to get fancy with printing profiles, I printed on it's side with tree supports to…
This was a stop-gap while I had a mount on order from Sabelt, but it completely exceeded my expectations and may have continued to use it if I haden't already order a permanent replacement. I used it on my SimLab P1X Pro, the wheeldeck…
Print all parts Place Pin inside Enclosure Block with the holes aligned Snap L and R arms onto pin. Should be interference fit, but glue is optional if you have a loose fit. Thread 1/4-20 rod through both arms for extra rigidity Attach…
Took the amazing design by @mreece524_2887371 and made it compatible with the T.16000M FCS HOTAS, I tweaked it all to fit the Trak Racer supplied profiles I had left over.
A adapter for attaching a pice of 8020 series 10 extrusion to the post on a wire shelf. Category: Organization
Roll in insert for attaching panels to 15 series 8020. Similar to 8020 part number 2488, but tweaked for 1/4" panel to sit flush. I printed in ASA and very strong.
A simple adjustment to allow mounting perpendicular to the T-track channels in addition to along the channel or on a wall.
CAD features + Footprint: Cutouts on the front and back for fingers, to make it easier to grab the gloves Small spring effect keeps gloves nicely in place Tiny edge blends to compensate for elephant's foot Designed to print in the strong…
Primarily I used this to drill holes to install screws through plywood and attach cabinets or other furniture projects.
Used a scrap piece of 8020 1530 to make a vertical rack to hold my 3 backpacks and my camera gear
Needed a lot of panel mounts and my vendor of choice was completely out of stock. Created a Fusion model and made my own. Since I could customize the slot for the nut, I didn't see any need for the extra thin 'fin' that the commercial…
Modification of the original clip that to accommodate a 10 mm diameter cable.
I build this mod because i never use my MSX without cartridges and i dont like let the cover open to use. The original one is from https://www.thingiverse.com/Wierzbowsky/designs Take a look at his profile, he builds awsome stuff.
Clean push-fit end cap for 45 series (45x45mm) T slot aluminum extrusion (8020-style profiles). Covers exposed ends for a finished look and keeps debris out of the slots. Friction fit, usually goes on by hand, but a few light taps with a…
These brackets are intended to be used for securing larger connectors or cable bundles (~1" / 25mm in diameter) to a 8020 simulator. They are 3d printed from PETG for durability. When installed they create a simple, clean, and low-profile…
The holder is capable of holding a vape with a width of 60mm x35mm.
This is a 3d printed sim racing glove holder (may also work as a sandwich holder). Designed to work with both metric or U.S. spec extrusion
These mounting brackets are designed for the Philips Hue Play lights. The brackets mount to your 8020 sim rig and the lights clip into the mounts. Each mount is secured to the 8020 rig via a t-nut and bolt. In my case I'm using 1 light…
This is a 3d printed sim rig cup holder. This is designed to be mounted to a aluminum extrusion rig (works with 40 series metric or 15 series standard size extrusion).
This is a 3d printed Nobsound NS-01G Mini Amp Mount. The holder is designed to work with the Nobsound model# NS-01G mini amp, which is a highly recommended inexpensive amp for powering transducers for sim racing. It may also work with…
This is a 3d printed sim racing phone holder. The holder is capable of holding a phone with a width of 90mm x20mm (The phone in the picture is a iPhone 13 Pro Max with a case for reference). Designed to work with both metric or U.S. spec…
This is a 3d printed sim rig wireless holder. This is designed to be mounted to a aluminum extrusion rig (works with 40 series metric or 15 series standard size extrusion). The 2 brackets are mounted on either side of the keyboard, so…
IKEA Tertial Lamp 8020 aluminum extrusion mount - fits 10- and 20-series, single-channel. Print with PLA or PETG, 15% infill triangle or gryroid infill. With PLA, I'd suggest at least 4 walls. Will only take up one channel width, the bolt…
This allows you to mount the Sabrent 10 port USB hub directly to a sim rig with M8 bolts and T-nuts. I'm printing mine at 25% infill in ABS, Gyroid, with 4 walls, should be plenty strong enough.
While assembling an 8020 15 Series assembly in the lab, we noticed that the 5/16" Slide In Economy T-Nuts we were using were not staying in place well. I designed a quick part that could hold the T-Nut in place during assembly. This will…
VW California kitchen cabinet shelf clip / supporting bracket — OEM 7E7068020. Designed to fit firmly and look like the original. ⚠ OVAL version: T6 / T6.1 only. NOT T5 (T5 uses the round 7H7068020). Print: PETG, 100% infill, on its side,…
I'm mounting this under my chair on my sim rig to power the adjustment motors in my BMW seat. Mounts a 200x110x50mm power supply to an aluminum extrusion using M8 bolts. The side holes allow you some slop to screw down a set screw to hold…
This cup holder can hold a variety of different cups, cans, and bottles, with or without a handle. It is designed to be fastened to a horizontal 8020 extruded aluminum rail with a single threaded star knob, a washer, and a hammerhead…
Used to attach a schedule 40 pvc pipe to the side of thy truck topper via the 1x3 aluminum extrusion. In my use case, to make a fly rod rube. Uses 1/4-20 hardware for clamp as well as 1/4-20 t nuts to mount to rail
Tired of Paying for Cheap End Caps? I wanted an end cap to protect myself from catching the edge of a frame I built out of 8020. I also wanted something that I could pressfit into place without having to tap or secure. Designed for a…
This was my first design. I needed a "hook" to hang my Philips Fidelio headset on my racing simulator made of 45mm 8020 extrusion. None of the available hooks were wide enough to hold the 55mm headband. This design will hold any headset…
Fits Aurasound AST-2B-4 onto 120mm 8020 tracks. There are three versions to accommodate different screws for mounting. It is very important to make sure you have good adhesion to the bed as I ran into issues with the print coming off the…
Alu-Cab shower cube mounts for 8020 1515 size extruded aluminum bars, this was printed by shapeways in 316 stainless steel. Mounts with ¼-20 bolts to 8020 anchors.
General Logitech webcam mount. Use zip ties for mounting webcam to the part and use the same screws and nuts as the rest of the acrylic parts. Currently printing the angled one to see what kind of difference it makes Print instructions…
A NEMA 23 motor mount for an 8020 series 1020 extrusion. It will require four t-nuts for attachment. Category: 3D Printer Parts
A NEMA 17 motor mount for an 8020 series 1020 extrusion. It will require four t-nuts for attachment. Category: 3D Printer Parts
One side has the same insets that are on the pivot hinges and the other can intake from a pivot hinge.
Migrating from thingiverse https://www.thingiverse.com/thing:4581821 Q-Scope QS.80200-P Lens Cover USB Microscope FreeCAD design file indluded
These 8020 Dowel Rod Hangers are used to hang wire for organization and dispensing. Hardware Required: 1 x 3/8" or ½" Tubing or Dowel Rod Print BOM: 2 x 8020 Dowel Rod Hangers of the same size as your extrusions Print Parameters:…
Though this isn't an exact edit of J-Max's 2020 cable clip it's the same exact idea and function so I would consider it a remix. I made this for any other person unfortunate enough to buy 8020 brand 2020 extrusion only to realize the slot…
A 8020 series 10 mount for making a display case. The project is documented here: https://www.instructables.com/Build-a-Simple-UV-Photography-Box/ Category: Art Tools
Yet Another Spool Holder ... this time for 8020 1" extrusion (25.4mm). It's designed to snap in, should make it easy to rack/pack lots of filament spools on an 8020 bar. It can take spools that are up to 95mm wide. Print instructions…
Remix / combination of https://www.thingiverse.com/thing:5093310 and https://www.thingiverse.com/thing:5188459 . Box to hold Arduino + Motor Shield for Wind Sim via SimHub on 8020 or similar extrusion aluminum. Original base wasn't…
