Liczymy pasujące modele…
Replacement sliders for Beyerdynamic DT 770/880/990 headphones. Yes, you can buy original replacement parts – for an insane price! Also they will break after a short time again because they are just too fragile. This is a remix of…
Remix of a remix of a remix, I really wanted the replacement to be as similar as possible to the original part, so I added a Beyerdynamic logo and L/R indicators. IMPORTANT: Printed with a 0.25mm nozzle using Prusaslicer 2.5 with Arachne…
This is my first design of mount for BN 880 GPS and two sma connector from DJI air unit. Printed in Flexfill 98A with 0,4 nozzle at 0,2 layer height
Breville / Sage Barrista Grinder Gear. Supported models: Express (BES875) - tested Touch (BES880) - confirmed by others These are not available as a separate spare part from Breville (Sage), but are the first to fail if the grinder gets…
Beyerdynamic Hinge Slider Replacement/Upgrade for DT770 Pro, DT770 M, DT990 Pro, DT990, DT880, Custom One Pro Plus, TYGR 300 R and MMX300 MK2
A wall mount bracket to click-in the Bosch Professional GAL 1880 CV battery charger. There is a channel to support the active air cooling of the charger. Update 19. April 2026: Fits also the BC1880 charger. To take the charger with you,…
To anyone who cuts their own hair and keeps it shorter than a few millimeters, I can strongly recommend the Remington “indestructible” HC5880 hair trimmer. The “indestructible” attribute only applies to the trimmer itself, not the plastic…
The official Cisco part for wall-mounting 8800-series IP phones has been getting increasingly scarce and expensive as of late, so I set out to make a 3D-printed alternative for use at work. Additional Materials Needed: - 2x M3x6 machine…
Holder to attach iPhone to LG monitor (27UN880), the iPhone works as Continuity Camera during video calls.
Tested on my HSKRC XL Frame (XL9 Arms), which is very close to the iFlight XL7. Standoffs in my case are 5mm (which could differ from the iFlight model), so the holes are tailored to that size. I added a TBS crossfire antenna holder to…
The battery charger Bosch AL 1880 CV takes up a lot of space on the table or shelf. So why not hang it on the wall? With this holder, the attachment to the wall is done quickly. Two parts, one mount and one latch. Print the mount with…
Use typical M3 threaded inserts along with M3x8 bolts.
This is a custom Silencer for my old Daisy 881. The gun does not have a thread so I had to get a little creative. Might also fit modern Daisy 880 air guns. Use the Testprint file to test the fit on your gun. (Warning: This can not be used…
A holding plate for the ch2i ic880a boards https://github.com/ch2i/iC880A-Raspberry-PI that form a nice LoRAWAN gateway. You will need standoffs and screws to mount the PCB to the plate. The design has holes for optimized airflow through…
Clamp for the Hakko FX-8801 handpiece (supplied with FX-888D) from fns720 's h eat-set insert press modified to fit thrutheframe 's press for 2020 extrusion and MGN9 rail. The clamps are secured with a 40mm M3 bolt. Two versions are…
Print in asa, abs or petg. Use same parameters as other parts
Didn't want to shell out $20 for the proprietary tool to use once so I whipped up this design. Was a bit of a tight fit but worked great. Print in default orientation, no supports. Use at your own risk.
This is a mounting bracket which fits the yaesu 8800, 8900, 7800, 7900, and probably others. When printed with ABS this is surprisingly strong (3mm walls probably help), but you will likely need longer screws than the ones you might (or…
The hole in the middle was covered with a 0.2mm layer to prevent supports in the hex socket. After printing use a knife and cut the hole open. Printed out of PETG but a hard TPU lasts probably longer. Print settings: 5 Walls 40% infill…
A quick and quircky plastic handle to replace a brocken mount of the Whirlpool 488000506980 fridge/freezer handle. According to this page , it must fit the following models: 859991054850 850466411702 869991054820 859991054830 859990962630…
Pretty simple designs. Not perfect but work well. I made these because the other ones I was seeing required purchasing special screws from the hardware store. I haven't verified all the model numbers in the title but they should be good.…
3D model, hardware description and arduino code to make your own Altair 8800. Feel like Bill Gates in 1974!!! More info Github: https://github.com/Menyiques/Altair8800 Printable using MMU2 or by filament change.
A wall mount for the Bosch GAL 1880 CV charger. Bosch really messed up here as there's no way to mount it onto a wall without modification. I printed in PETG, PLA is also fine. Use four 3mm x 20mm machine screw to secure the wall mounts…
The model was made by measuring by hand and without the datasheet, so it won't be precise to the highest degree, but good enough for using as reference for other designs. It only has features that might be useful when making other…
Tail mount for iFlight Chimera 7 frame. Includes space for DJI air unit dual RP-SMA connectors, TrueRC Bardpole, BN880 GPS, and TBS Crossfire diversity RX. Thing contains two versions, one with cutout for power to be brought topside via…
This is a single pellet loader for Daisy 880s and Winchester 1977s (177 cal). This loader attaches to the dovetail rail with M3 x 25mm screws and nuts. To use, slide a pellet in the ramp with the gun tilted slightly muzzle down and bolt…
I haven't tested this yet but I'll be doing the 20K km service on my Street Triple soon and need this tool. Let me know if there are any issues with it. Designed for a 22mm socket. You'll need to consult your service manual for the torque…
Gridfinity Knipex 880250 water pump pliers Wasserpumpenzange The 2 parts do not need to be fixed. They hold by themselves due to the grid. If you still want to secure it, you can use the magnets. 2x7 grids. See all my tools…
This is a “minimalistic” wall-mount for the Verizon JetPack 8800L MiFi Hotspot. I may go back and reduce some unnecessary corners and mass to make it truly minimalistic. I designed it using a 3D scan of the device, so it should be a tight…
For bigger printers, scaled up to 160%, 886mm slide the front bulkhead in through the back of the middle section(some sanding is required for a smooth fit), other bulkhead should fit fine I have not printed this yet
A simple clip similar to the one that comes with the BTR5 to mount directly to your headphones with no drilling required!! The clip simply wraps around the left cup arm and secures to the case with two screws. For this project, you will…
This is a Helical Antenna for the 915mhz band. Intended to be used with rocket avionics but will work for any 915mhz application. Copper wire is 1.7mm solid coper. Build Video can be seen here https://youtu.be/JCoJQt3CkDY Print Settings…
This model is compatible with the lego system.
Mount for the BN-880 GPS module for the TBS Source One V4 frame. Or any frame with standoffs that are spaced 24mm apart on center. This particular GPS I purchased from RaceDayQuads, but I think all BN-880's are the same size. Print…
A gear of my thickness broke a while ago. The sparepart costs more than 40 €, so i decided to remodel it. Works like a charm. Print settings: Print with something sturdy but not brittle (Tough PLA or Nylon) 100 % Infill Standard-Quality…
Hi, this is my original project for Eachine Wizzard X220 V2 (but it will also suit to many other 5" quad drones). It's size is designed for typical antennas and Beitian GPS BN-880Q with compass. Print it in slow motion with 100% infill…
Mount for BN880 Compass & GPS and RX for Mark4 V2 Layer Height: 0.15 Wall loops: 4 Infill: 35% Cross Hatch Support: Tree (manual)
A0029880181 Clip für den Daimer, gedruckt in PETG oder PLA, ca 15 min.
Reaplacement part for Beyerdynamic DT 770/880/990 headphones, to be used with original screws. Designed from scratch based on the original ones, intended to be stronger. Recommended settings: PLA at 0.15 or 0.2 layer height, no supports…
This is a basic mount for the common BN-880 module, designed for one of my own frame designs but which might be a useful reference for other people working with the BN-880. This design uses M3 heat set inserts with a hole spacing of…
Hood seal / Windscreen support. The insert needs to be adjusted with a knife!
Becker aeromat 200071880 Nozzle Becker aeromat 200071880 Dysza aparatu wysiewającego
Alfa Monster BN-880 GPS Holder Created in Sketchup. Source file inkluded Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: Doesn't Matter Supports: No Resolution: 0.16 Infill: 30% Filament: [ No Name PLA…
Theses models allows it to replace the original Thecus motherboard agains an standard mATX motherboard and a silent PSU.
Remixed another model to make the GPS level with the top plate to avoid prop collision and added screw holes that fit the Tyro129 and Tyro119. DJI FPV unit is zip tied to the top of the quad with the antennas feeding into this print.…
Mounts a BN-880 GPS ontop of the camera cage of an Armattan Marmotte & Badger. Category: R/C Vehicles
This model is compatible with the lego system.
GUITION JC4880P443C-I-W Desktop Stand This stand is for the version without a backplate. The screen is loosely friction fit, you could use the pre-installed adhesive if you wanted to but would make removal of the screen for debugging a…
Its a remix of two models on Thingyverse
NOKIA THR880 THR-4 – TETRA RADIO Antenna Cover Supports are needed on the internal ring. It sits very tight. I printed it in PETG.
Given the original files were irretrievably archived by Autodesk during their Fusion 360 downgrade, this will be the last version. THE V5 FILES ARE CURRENT AND HAVE CORRECTED DIMENSIONS The "Fancy" version has some nice chamfers and…
Designed a camera case to mount on one leg the Ikea Lack Enclosure. You can tilt it left / right, up / down. You need: 2x M4x16 Srew 2x M4 Nut 4x M4 Washer 2x 5.0x20 Wood Screw or similar Suitable glue to stick on the hinge parts (i used…
GPS and antenna mount for the FPVCycle Glide frame for the Caddx stock antenna and BN-880 GPS unit
IFlight XL5 BN-880 GPS holder An absolutely minimal mount that wraps around the GPS pcb and is being held by the two rear bolts. Print at 0.2 layers, 0.4 nozzle using PETG or TPU96+. After printing open the arms of the support and insert…
Circus of the Past - Performers - Trapeze Acrobat from 1880's 3D printable model.
BN-880 mount for Martian frames Print instructions Category: R/C Vehicles Summary BN-880 mount for Martian frames
Printing Just print them outside-down. The screw counterbores shouldn't need supports, most modern slicers can automatically bridge the inside. This image is looking up from below the build plate to show the bridges in the counterbore. I…
This is a replacement slider mechanism for Beyerdynamic DT 770/880/990 headphones. You will want to print them with the flat side facing down. I printed mine with 3 walls, 25% gyroid infill, NO supports, and a 0.12 layer height. I…
This a simple tablet holder for the FYC JK8801F Folding Treadmill. The area for devices is far too small for a tablet to sit in landscape view, so I created this that slots into the existing device holder. I printed mine in PLA with 15%…
Add some 3M VHB double sided adhesive or other similar product to the back and stick it onto your DT880s
Description BN-880 GPS holder. Strudy mount. Route cables on the side with some cable slack. Print Settings Printer Brand: Creality Printer: Ender 3 Pro (Direct drive) Rafts: No Supports: yes Resolution: 0.2 Infill: no - use 500…
Repair your broken A6398800985 by glueing this part onto the breakage. It will work with just superglue. But for extra strength, drill 1.5/1.75mm holes through the lashes and stick some filament through the lashes. Apply more superglue or…
About I had a look around, and I didn't really find a solution that i liked much, so I designed my own. there is two channels for small zip-ties in the bottom, and its angled about 20 degrees to the back, so a forward flying drone should…
Bed Model to use with Simplify3D, PrusaSlicer... Category: 3D Printing
This is a snap in adapter for the Hako FX-8801 soldering iron used with the Modular Arm by @reemo3dp and for the heat insert press here: https://www.printables.com/model/808502-heat-insert-press Printed my first one in glass filled PETG…
This is a GPS mount for the Beitan BN-880, which is my favourite GPS. This mount is designed for the Blade Theory XL drone frame but should work on any frame that has 33mm hole spacing. You might need to scale it in the Z direction. As…
This is a sideways hook style mount for the Ryobi OWS1880 Sprayer, it allows you to mount it to the wall. I store the batteries seperate, however it will take the battery weight as well Mounted with standard No.8 screws
This model is designed to work with the milwaukee m18 vacuum backpack model 0880-20. This model is meant to aid in the use of the vacuum. Easily indentify and start the vacuum on your desired setting.
I designed this to mount a BN-880 GPS module to my iFlight Nazgul5 quad. The hole spacing is 22mm to fit the rear mounts on my drone. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 18%…
needed some more space behind a flush mounted led lamp, this is the result. There is 80mm between the lamp mounting holes. The hight of the ring is 15mm and will fitt a 3x2,5mm^2 cabel ment to be mounted on wall. Fits Jula.no Art. nr:…
Designed to hold lathe tools for the Wen LA8800 lathe stand. No Supports needed STLs have been uploaded in print orientation 4mm mounting holes for nuts and bolts or zip ties (This is how I mount them in the pictures) Tool hole is 28.86mm…
Ersatz für die originale Riemenspannerei mit der originalen simplen Schraube. Hier werden die originalen Lager und die Vierkantmutter wiederverwendet. Das Spannen ist absolut simpel und genauer wie mit dem Original. Bohrschablone…
MH-8800G/5 DYNAMIC UHF Microphones holder - Provide wall storage for 2 hand held microphones type MH-8800G/5 DYNAMIC UHF Microphones
Description This case was designed from scratch for the GUITION JC4880P433 development board (ESP32-P4 with an ESP32-C6 and a 4.3" touch display). I wanted a minimalist design that holds the screen at a 60° angle (you can also rotate it…
Puzzle description: This is one of the oldest checkerboard dissection puzzles, it appeared around 1880. Put the 15 pieces together to form a 8x8 checkerboard with correct pattern. The pieces are one-sided. For more historic information…
[ IMPORTANT in order for this part to fit, you have to scale it from 100% to 10 % ] This is a spare part for upper basket rear stop, which you can use instead original part, it's cheaper and faster to print, PLA under a dishwasher…
Remixed from IFlight XL7 V2 TBS GPS Puck Mount by grammo For Iflight XL7 frame ( https://goo.gl/Fo1rmg ) Added the mount for the BN-880 GPS, you can fix it with an zip tie. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No…
This fits into the blank space of the skeleton sheet, after your button broke off. Size of the Frame is 24mm x 21,5mm.
This is a tray that holds the BN-880 GPS and allows the wiring to drop down through either side. I had seen a couple of other designs that required gluing into the fuselage, but my FC is mounted under the spot where this fits, so I needed…
This is a GPS mount that replaces the front Gopro mount. This was modeled for the RDQ BN-880. I Was unable to get a GPS signal until I moved the module to the front of the quad.
Wall mountable holder for Wolfcraft 4688000 (90 degree screwdriver adapter)
Sicherheitsrahmen für den icom ID-880H Saftyframe for icom ID-880H
This is a quick and dirty threaded insert helper to use with a drill press and a ¼" bit and the Hakko FX-8801 soldering iron. This is to get the job done. This is not like a precision press since the drill press chuck can rotate but I…
BN-880 GPS mount for my Eachine Cvatar. Very light weight. Printing in TPU is preferred, but PETG also works well on this design. PLA might also work, but I have not tried. Supports are needed due to the central overhang. Hole Spacing for…
The BN880Q is a GPS with compass. Buy one, to upgrade your Tyro129. If you want to print a backpack for the original GPS, go to https://www.thingiverse.com/thing:3948966 All you need to mount this, is 1 cable tie. The cable tie is the…
This is my design to mount a raspberry 3 with camera to my 3D Printer (Velleman K8800). The camera can be oriented by the loc-line. There are two types of loc-line, the normal one and the one with a mount for the camera cable. For better…
Modeled to contour to a Cisco 8800 series handset. I use the smallest size Ranger Band, cut into thirds, to attach it to the phone. Depending on the size of the push-to-talk button, I've included 2 versions of the button insert.
Heizbett für den Velleman Vertex K8800. Ich wollte den Drucker nicht unnötig verändern, darum habe ich das Heizbett unter der originalen Druckplatte untergebracht. Als Heizung dient ein 12V 50W 100x100 mm Heizpad, das über einen…
EN: Xbox Controller Stand Venom VS2880 Single Dock Xbox One VENOM VS2880 controller stand base - wall or shelf placement. There is space for the controller charging cable on the back. Recommended print: Fuzzy Skin made of nice PLA Stand:…
Print one V-Boom Clip right or left side. Tested on DT990 Pro. For this project, you will need: 1x V-MODA BoomPro Microphone Detachable Flexible Boom Microphone for Headphones 2x M3x8mm Socket Head Screws 2x M3 Washers
This model is a 1U 10-inch rack mount, designed specifically for the ONU XPON PL8800Z All model CAD files are fully open-source and available for download Check out the GitHub repository to explore the project Variants To accommodate…
Endoscope mount for Vertex Delta K8800 endoscope used = cheap 7mm diameter endoscope (AliExpress) => but diameter has a lot of tolerance, so I added the Fusion file, so you can modify the diameter to your needs... Enjoy! Print Settings…
I do like all the designs of StoniXX for the Vertex Delta K8800 This is not a real remix, but more of an add on... My mosfet heatsink was somewhat bigger, and couldn't fit it in the housing. So I made this, it's an extension of the…
Am Velleman Vertex K8800 ist das Display von oben schlecht abzulesen. Da der Printer bei mir recht tief steht auf einem niedrigen Tisch, gab es da immer Probleme. Daher habe ich die originale LCD Montageeinheit mit einem Pult versehen.…
Motorabdeckungen für den Velleman Delta K8800 Printer. https://www.thingiverse.com/groups/vertex-k8800 Print Settings Printer Brand: Deltaprintr Printer: Deltaprintr Kit Rafts: Yes Supports: Doesn't Matter Resolution: 0.1 Infill: 30%…
Notaus für den Velleman K8800. Der Schalter erzeugt einen Reset in der Steuerung. Der originale Reset Knopf ist im Betrieb nicht zu erreichen, der Netzschalter auf der Rückseite ist ebenso ungünstig gelegen. Wer den K8800 hat, weiß das…
Some repair operations on sony Betacam SP VCR PVV-3 require this fixture. Never saw a rel one, so i created this based on illustrations from service manual. It is not perfect but it does the job. It is not as rigid as this part should…
Designed to fit over each end of the CyberPower Model 880 surge suppressor. Mounts with four #6 screws to a flat surface. Prints without support. Printed with 3 perimeters, 10% triangle infill, oriented with flat side on print bed. Modem…
Popular mechanical key lock in many ATMs and safes: S&G 6880 (and family 6800) - this is optional front cover 6880-511 (this is simple version, without swing cover like 6880-500). Holes should fit in typical safe box with predrilled…
