Liczymy pasujące modele…
Update: (8/21/2023) - Added new version for x-Max 3 - with spool holder mount at 90deg - note that this will position the desiccant well at the bottom ONLY if the holder is mounted on the right side of the printer. Also reduced the…
Spool holder clamps to handle of the X-Max3. Allows use of Qidi drybox or a regular spool. 2x M3 x 50mm fasteners are required for the clamps. These are the same as the fasteners you likely removed from the printer during the installation…
I designed this spool holder for QIDI printers because the original one, when used with cardboard spools, often created too much friction. This could lead to false filament tangle detections and also generate annoying noise. After…
Based off of the updated back cover with fan. Increased fan size from 20x20x6 to 25x25x7 and added more vent holes. uses M2.5x9 button head or maybe m2.5x8 flathead screw. i made mine from ASA. Will make from a higher temp material when I…
Wall support to install this xiaomi router. Added some design features...
I needed a larger bezel for my car as it has two single DIN frames (rather than a double DIN). I made this with a larger bottom edge to hide the gap, it fits snugly around the AX1000, AX3000/AX3200 and AX5000 screen. I curved it to match…
Made this simple riser block for the top lid on my X-max3. Didn't want to take the lid of when printing PLA so this was a simply fix for that. It has two small taps that slots into the holes in the frame. It fits both in the front and in…
I created this model to quickly replace the broken part in feeder and continue printing. it works wery well, but step file is also attached. UPD Jun/20/2025: replaced with v11, more sturdy now
This remix of the Stable Bambu X1C plate holder by Mark (which I use many for my X1Cs) has been remixed to fit the large Qidi 330 x 330 plates comfortably. Very stable with one or more plates installed.
The stock motherboard cooling fan for the Qidi Xmax3 is quite loud and always on. The motherboard does not have any extra programmable fan headers, so I designed this replacement back cover to install a silent 120mm fan in place of the…
Small wall mount for the TP-Link Deco AX3000 X55 Router. It has two versions, one meant to be used with 3M Wall strips for clean mounting and removal, and one with a screw hole. Arch design supports the weakest area of the print so it…
Front : New version stronger and looking more like the orginal one. But still very short ! Rear : just the same with reinforcement. Print Settings Printer: anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 100 Notes: Printed on my…
The Qidi X-Max3 is prob the best consumer printer right now with some minor flaws. Most of them are easily fixed with some modding. One of it is the back-mounted-filament-box/hanger. This is unpractical. Whatever you use instead, like a…
Clip de rechange pour extrudeur de X Plus 3 lors d'une casse du pion de fixation
Printed in ABS Like Resin but will also work on a normal FDM Printer. Support is needed. I would use 3lines and like 20% infill. Also use a Material for high temps cause its in a closed case.
The internal camera of the XPLUS3 is affected by the internal LED lights, causing severe flare. If a self-made lens hood is attached here, it will hit the print head at maximum approach and cause damage accidents (This actually happened…
I'm in the process of modifying an printer where i want to use a Voron dragon burner tool head. I had to make some modifications so i needed a 3D model of the hotend for my Xmax3 so i drew it up in Inventor so i could make an assembly.…
Stick, screw or glue on top of Quidi X max 3 to hold lid open when printing PLA or PETG, but still have dust and cat protection.
Use Tape, glue or screws to mount to the side of the door, needs 1x 8x3mm magnet, make sure to insert the magnet the right way matching the door magnet, (magnet attaches to existing door magnet) https://a.co/d/fQN8eWw remix of this…
Recommend printing in orientation provided as laying down the axial torque is likely to separate layer lines.
This is a din rail mount for MAX31865 breakout boards. You will need the Voron din rail clip as well, it can be found here: https://github.com/VoronDesign/Voron-2/blob/Voron2.4/STLs/Electronics_Bay/pcb_din_clip_x3.stl Print both files and…
As I have been told, that I run my Run out sensor in reverse, I designed a new bracket to use the BigTreeTech Smart Runout Sensor V2 instead. I tried to connect the sensor to may printer by following Ben's Tutorial…
10inch rack holder for Mikrotik. With this it can be mounted only from behind, because hAP ac3 (ax3) is too wide to stitch it between rails. Printed from PETG, holes are 5.8mm, so M6 screws can be directly used. Use organic support for…
Allows mounting of the TPLink AX3000 wifi antenna to a wall. Use #4 wood screws.
I stopped using this mount and moved the probe into the back print head cover: https://www.printables.com/model/1317184-qidi-x-max-3-magnetic-printhead-backcover-for-btt The Bigtreetech Eddy probe upgrades the original inductive or…
The wall mount bracket of the HUAWEI wi fi a3 router is based on the model of the router itself. https://www.printables.com/model/1331151-huawei-ax3
I modeled this shield after the motherboard dimensions. It fits perfectly on the board and in the case. It is a bit bigger on the ports opening than the original metal one but it still looks nice and quality. The photo was taken before…
Print face down .2 with bed only supports
This is a simple enclosure to prevent stuff falling in the front case of the printer. There is a big gab and i had to get mutliple small parts and junk out of it. Now its closed so no problem anymore. The caps you can secure with a trop…
Qidi X-MAX3の為の部品です。 ケーブルキャリアが右奥に移動した際に、フレームリブに干渉してしまう恐れを回避する部品です。 右側のステッピングモーター取付フレーム、上部にある四角の穴に差し込み使用します。
This mod requires soldering and putting holes in your walls and modifying your dry box, but will allow you to relocate the filament run out sensor to the top of the printer and mount the dry box to the wall.
it was print with printer model Qidi X-MAX3 and it sit made for fan 92x92x25mm Noctua NF-B9 redux-1600, it is necessary to reduce the voltage from 24V to 12V, therefore there is a box for a DC/DC converter (MP1584 DC-DC Step Down Power…
This is a robust wall mount for the AX3000 router, which can be mounted directly on the wall or on a flush-mounted box with a hole spacing of 60 mm (for this option, holes must be drilled on the back side of the wall platform part). A…
I made this design for a project in which i needed to join an ESP32 and a MAX31865 in an electrical box. Simply slip into the holders the ESP32 and screw the MAX31865 on top with two little screws
A simple lens hood I made for the ofiicial camera for my X-max 3 to block the glare from the LED lighting. QIDI links to an existing one on here, but I did not care for that one as it is visible in the cameras field of view.
I had heard that the Xmax3 are the same size as the Plus4 and are swappable (with some changes to the plug) (reports are the q1pro hotends are the same length as the plus4) Later on I heard that it is 4mm short. So I Stewy helped me with…
This is my Y axis conversion for the Simax3D Iron M1 printer; I did this to compliment my X axis Linear rail conversion. You will need the following parts: 2 x MGN12H 300mm Linear Rails 10 x 2020 M3 drop in nuts or T nuts. 10 x M3x10 ~ 12…
MECH-AX37 is finally finished! Say hello to MECH-AX37, my latest and greatest fully jointed and printable mech! Material Frame parts ABS, ASA, or PETG Armor parts Any Layer height First layer 0.2 mm Other layers 0.15 mm Number of…
Hier eine einfache Halterung für die Seite am Qidi X-Max3 über die Griffmulden. Es werden noch 2 Schrauben M6 benötigt sowie eine Schraube M5. Die M14 Schraube im Bereich des Gewindes und kurz davor auf 100%Infill drucken. Durch das…
Only a remix of the original extruder cage to allow the usage of a 4mm bearing with a Omron D2F-L switch. I didn't have 5mm ball bearing and was missing the predrill for the switch. Additionnaly, if you have an inductive Probe on your…
Custom dash kit to install a Sony XAV-AX3250 in a MK4 volkswagen Jetta (mine is from 2004, but I believe it should fit all MK4 Jettas, and potentially other VWs from the era). Is a toolless and screwless install. When printed face down…
Vertical stand for an Asus RT-AX3000 router, clearing up desk space and allowing antenna positions you otherwise couldn't achieve. The “wings” above the mounting pegs provide a surface for the router feet to rest against. Suggested print…
This is a mount for a Raspi camera (original version) will seat a 1"x1" board. Put a channel top and bottom for routing the cable away from the belts depending on the install orientation.
A friction fit case for the following cheap web cam: https://www.aliexpress.com/item/1005008262694281.html I'm cheap so didn't want to pay over the odds for such a simple thing. £6.50 is McDonalds money…so join me in my budget friendly…
A quick design of a nozzle wiper/brush mount I through together. It works well enough but I am I think it could be improved. I was really just taking a guess as to what would work. There is limited space where the nozzle can reach around…
Just an addition to the available side mount tool holders to hold the wrench and hex keys.
Heat set inserts are now installed from behind the plate. Additionally there's “_short_offset” file, I noticed that the rear holes were not aligning with my micron carriage, so I moved the holes 1.5mm up to better align.
Guten Tag! Hier mal eine Spulenhalterung für den Qidi-Tech X max3. Da die Originalhalterung für mich völlig unbrauchbar ist, habe ich mich mal hingesetzt und in Blender was gemalt. Ansonsten ist der Qidi ein Top Drucker, muss aber bei mir…
One of the biggest annoyances with the X-Max3 is the lid being in the way every time I have to reach in the top
A quick release ceiling mount to use my Cudy Router as a Wifi AP with excellent positioning for a strong signal. One side screws to the AP using M3 Screws and a Nut and or washer to slide into the APs wall mount slots and grab a hold. The…
Larger duct for qidi carbon filter
This part is a spacer located at the back of the toolhead, between extruder mount and PCB. It broke when I replaced the PCB with the new one, so I had to design this replacement. Printing it in ASA, ABS, or PC is recommended.
This is the result of observing the movement of the tube and making improvements.
Made for the 42mm square ELP USB camera https://a.co/d/1gdbB17 20 degree down angle 25mm riser
Needed a simple snap together case for a thermocouple breakout board for my kiln. Printed in ABS.
ASUS Router stand for RT-AX58U or RT-AX3000. I superglued the support to a pair of stands. I also uploaded a one-piece version
The original clips broke the first time I removed them. I designed these to replace them. It is recommended to print them in PETG or ASA
This is a mount for an Adafruit MAX31865 board, which is used to drive PT1000 and PT100 sensors with a MAX31865 over SPI. This DIN mount is styled like other DIN mounts for the Ender 3 NG v.2. Works with upstream Klipper. Here's a link to…
Holder for Nevermore V6 filtration system. I use 3xM3 screws that I found around to screw it to the holder. There are two additional teeth from the bottom that supports filter carriage. Attention! Holes does not fit perfectly as it…
Printed @ .2 Bed supports only on. I used Ender PLA at 100% infill, Suggest longer screws as stock are too short as it is. Both files can be printed at once if desired.
Print in PETG, i use 4 walls, top, bottom with 30% grid infill. (single screw to flex more and be able to rotate it) Onshape link in case you want to add more holes or make it thinner…
Mounts a 41.5mm square bracket that snaps onto the door trim. No hardware needed. Camera used: https://a.co/d/7WPFmIH
good mount foe your router!
This is the culmination of projects while I've been printing parts to build a Voron. I decided it was time to convert the X axis to a linear rail. I combined this with my shroud design which will hold any E3D V6 compatible hotend. The X…
Why bending yourself to observe the first layer lines?? Now you can just set, print and observe it in the comfort of your chair/bed… Preparation To get the nozzle cam working on your xmax3, if you already have a camera, you'd need to…
Qidi X-Max3 Filament spool holder and BTT Smart Filament Sensor V2 mount I have made this filament spool holder for the Qidi X-Max3 It mounts to the original runout sensor mounting with 4 screws or you can used 2 x 6mm bolts by inserting…
The lid snaps in, just screws for mounting the electronics required.
The original Qidi inductive probe failed on my printer and i had a Super pinda laying around from another project. Dimensions have been taken from the original Qidi mount, so no need to edit the printer.cfg as the X/Y offset is the same.…
По сути это перерисованный кронштейн с моими изменениями. Оригинальную модель не удалось экспортировать в твердое тело и я просто оцифровал эту модель и изменил ее исправив некоторые моменты. Схема подключения выглядит следующим образом:…
120mm Fan reducer to 100mm vent tube for Qidi X-Max3 , 120 mm Fan replaced 80mm fan ‘bit of cutting and sanding required’ I then attached 100mm Alloy tubing and vent to wall outlet I had made.Also included is 120mm fan template to mark…
I designed this E3D mount for the Simax3D IronM1. The stock hotend works fine, but it's not all metal, and it's really loud. My initial design, was simpler, and worked well; until I started printing ABS. The air flow from the heatsink…
NOTE: BEFORE YOU ARE GOING DOWN THIS ROAD, MAKE SURE YOU KNOW WHAT YOU ARE DOING BEFORE SWAPPING STOCK BOARD. WARRANTY WILL BE VOIDED This is the mount for the Manta M8P or M5P to be used on the X Max3. BOM: 4x M3 dia4.5mm Heated inserts…
After upgrading the printer to the unpatched upstream Klipper firmware, the Qidi touchscreen no longer works. (Compare https://github.com/leadustin/QIDI-up2date-english/blob/main/Klipper-Update/update+upgrade.md) I used this adapter plate…
Gives drone like shots without the drone for those that want footage of their vehicle racing 4WD driving etc. The original mount using 8mm carbon square had some vibration when coming out of corners so changed design to suit 12mm carbon…
The Powkiddy RGB10Max3 Pro is a retro handheld emulation game console that runs on Linux. It's design and shape allows for a case that be used on the front or back of the device, allowing the case to be used as a grip case or a protective…
Printed with 4 walls, but can probably work just as well with less. Uses three hooks from this set called Skadis_Shelf_hook.stl Needs two M4x10 bolts for assembly, which are threaded as is into the corresponding holes. Make sure your…
Height adjustable camera mount for Rapberry PiCam and non-adjustable height lightburn camera mount. .3MF file included so you can adjust or modify.
It appears that Voron has been using a different PCB DIN plate for quite some time, so other MAX31865 plate to PCB DIN adaptors don't work (they expect the self-tapping screws to be farther apart. This kit only requires: 2 self tapping…
I used ASA. Supports are needed. separate the heater from the fan. use those 4 screw to attach heater box parts list Qidi chamber heater(heater and fan) 2x HEPA filter(80mmx40mmx15mm) 6x m4 threaded heatsert 6x m4 x25mm flat head cap…
Rod mounts in standard location on the rear of an XMAX3 to allow for use of a 3kg spool, without the drybox. Category: 3D Printer Accessories
Simple holder for 3d printer nozzles. Can store up to 9 in it. Printing Recommendations: Filament: PLA or PETG Supports: none Infill: 15% If you like my work and want to support me, you can buy me a coffee here:…
Simple spool size reducer to fit in GTMax3D spools in place where a tighter hole is needed (for example Bambu A1 AMS). Will with a tight fit adapt a standard GTMax3D spool from 72mm to 55mm. Printer Settings: 0.4mm Nozzle 0.28mm Layer…
I made this to wall mount the Linksys AX3200/E8450 because I didn't want to sit it on a table somewhere. I do believe others might want this as it is slowly becoming a popular router for OpenWRT and other open firmware on the market. I…
Require: PC4-M10 PTFE Tube Connector
I wanted to mount a Nevermore V6 in my Xmax3. So i designed this blanking plate that does double duties. Both blanking off the exhaust fan hole and has mounts for this Nevermore V6 holder.…
印刷中に問題が発生し、ホットエンド周辺に大量の材料（PLA）がありました。解決策として、ホットエンドを300℃まで加熱して溶かしました。オリジナルのダクトは破壊して解決しました。基本的に外側から外せると、良い結果になると思います。最後のモデルはPAHT-CF等、高温溶解時にホットエンドを冷やさないように出口を、これまでのモデルより外側に向けました。エラー停止し難いダクトだと思います。
Qidi has such a long filament path and the drag affects print quality sometimes. Thatswhy I decided to use a filament buffer device. I print ABS but you're good to go with PLA or other shit you have laying around. Very simple CAD model…
This is a work in progress. It is a part to provide some extra strength to this fairly fragile design, in addition to making the belts serviceable. It retains the socket head cap screw as the Y end stop. I designed this after my Y axis…
Содержит две детали, позволяющие почти полностью блокировать паразитную засветку как соседних световодов, так и внутренностей маршрутизатора. Не требует доработки напильником. В ходе моделирования и подгонки пострадал один роутер. RIP.
Alignment PEI for QIDI X-MAX3
Google 翻訳で開く • A poorly placed runout sensor resulted in the waste of expensive materials and valuable time. Just as I was searching for a solution, a clue popped up: Using the D2F-L2-D runout sensor provided a reliable signal. However,…
I designed this simple bracket for mounting this access point. The tabs lock in to position solidly yet still easy enough to remove. The center cutout serves no purpose other that to reduce filament usage. I printed the prototype using…
マザーボード冷却ファンの起動条件に疑問を持ち、目的を達成する為に2個のファンを必要としました。ファンにはエアーフィルターが必須だと判断しました。 2個のファンを調整するためには、プリンターコンフィグレーションの変更を加える必要が有ります。
This plug fits into the X-Max 3 Z-rod mounting holes to keep debris out. I made a top plug and spring combiner to get the proper height with what I had. The springs are 33/64" x 9/16" 22gauge stainless. It's just enough to push the plugs…
When you're tired of dry box mounted at back. Usable for both sides, but on right side fan could complicate drilling and mounting. Maybe you needn't take off side fan, I moved bolts higher then on photos. But drill holes for them…
A remix adding a TPU seal and screw mounting using the existing hardware.
Introduction: Concerned about the Vocs produced by printer, I believe a fume-hood like air filter would be helpful to remove most of the odeur gaz from the inside of the printer before they diffuse into the surrounding. This design has…
added RH side holder and rotated LH side so the bowden tube has a better shorter path
[Note that the photo used for this listing is from an earlier test/draft. The final posted here is better] Pedal for the Korg AX3000G. Probably works on other AX3000 or Korg models. Print on the side and use tree supports
