Liczymy pasujące modele…
Update 3 The center of the hole in the fan adapter was off-center with the fan, so I corrected it. Please use “fan adapter v3”. fan adapterの穴の中心がファンとずれていたので修正しました。「fan adapter v3」を使ってください。 Update 2 アップデート2 There was a gap between the…
Cyclone dust collector. Can be printed in two parts on the Prusa Mini! Bouth parts have a rim to be fitted together neatly. PrusaSlicer Files have all the necessary supports!
Cyclone dust collector for a 2.5" hose. Made to be as large as could be on a Prusa i3 mk3s. I used m3 hardware to put the top and bottom together but glue would work just as well. ¼-20's for attachment to the bucket. I put this on top of…
This is a marble machine with a lift that lifts three (or more) marbles simultaneously, and releases them to three separate tracks. Two of those tracks are connected in series, so a marble will therefore alternate between those tracks.…
January 31-2025 Version 4.1 released! Version 4.1 is released! minor mods and tweaks! November 26- 2024 Version 4 release! (note - v3 and v4 lower cone is the same(NOT V4.1!!) , only the upper inlet/outlet section is new so you can reuse…
This construction is a logical continuation of one of the first options. The community likes it, apparently because of its low profile. It seems more stable. Our friend Der_Rudi asked to increase the gap for better throughput. Now it's…
Version 3- new, even bigger and better cyclone dust separator! This is still a beta! thou it is fully functional! Assembly info and such will be added later, newer versions of the top cap may get uploaded ** note- will need a 300mm build…
This is a rework of my own model from thingiverse (from 2012). “cyclone to catch the spray while purging/cleaning an airbrush.” There may be some sputtering especially with airbrush nozzles bigger than 0.2mm. Prints without supports, a…
Also called a “Cyclone Dust Separator” or “Dust Collector”, I needed one but the ones available were too expensive. I printed it with PETG. I am not sure if PLA will work. The print is huge and uses up a substantial amount of filament.…
This is a wall mount for a Shark hand held vacuum with a charge port. This should fit the following models CH901, CH950, CH951, and CH955. I was surprised to find that this model does not come with the wall mount, same issue with the more…
Need a custom adapter for your cyclone separator? Comment the required inlet and outlet dimensions and I’ll make and upload it for you. This 3D-printable cyclone separator efficiently removes dust and debris from your vacuum system —…
I made this cyclone separator. It consists of five parts, four of which were 3D printed. The last, the top piece, was made out of acrylic on my CNC router so I could see inside but it can also be 3d printed. In my test it worked…
Universal cyclon for vacuum cleaner. Can be attached to any container. Use a 250mm long drain pipe diameter 50mm in the center. Use screws for attachment. Make sure you seal the cyclon to the container.
Check out a video about my project! I tried to use 3D printing to speed up production on a laser cutter. A simple cyclone separator that can be easily printed within 20 hours saves you money on bags and works amazingly well!
Cyclone dust collector for 100mm hose diameter. Print and bond the 4 parts together A mesh structure has been added to the cyclone3 component to prevent large debris from being sucked in. Please download according to your preference…
small fine mist sprayer ∅8mm connector (with ½" adapter)
Cyclone Seperator for Festool Vacuums This is my custom version of a cyclone seperator for Festool vacuum cleaners. The goal was to build my own, cheaper version of Festools CT-VA-20, while maintaining the core functionality without…
For experienced makers. Remember this is a free file. Ready to get your socks sucked off? This is a handy dandy, print-it-yourself cyclone! If you are looking to upgrade your dust collection system, we highly recommend giving this design…
Want fine water spray but can't print a fine nozzle? This is using centrifugal forces from a cyclone to nebulize water so it can be printed. I recommend using PET-G as there is some water pressure involved - please use caution! 8mm ∅…
Cyclone Dust Collector The Dust collector main body fits perfect on a Prusa MK3 Printbed. Update 03.03.2025: Os Vac Neo M32 Intake and Outlet Adapter Update 25.01.2025: Os Vac Neo F32 Intake and Outlet Adapter 35mm, and 38mm outer…
Das ist ein Unterdruckventil für einen Zyklonabscheider. Es kann mit Hilfe der Feder eingestellt werden und verhindert das implodieren eures Sammelfasses. This is a vacuum valve for a cyclone separator. It can be adjusted by means of the…
This is a parametric dust extractor designed with a small shop in mind! The included STLs are ready for a 45mm hose and mount to the dust bin via 6, 5mm bolts.
M48 Cyclone Spiral Boot Knife Knife inspired by the M48 Cyclone, featuring two interchangeable blades with a three-cut spiral design. The sheath can be used as an additional handle, resulting in two Cyclone knives.
osVAC conversion adapters for Dust Commander cyclone dust separator. With these adapters you can attach osVAC hoses directly to the Dust Commander. Also check out my osVAC pressure relief valve adapter. The female connector uses my osVAC…
Small cyclone separato for 35mm vacuum cleaner tube. Use tape to glue the two parts together. Supports only on build plate for top part. No support for buttom part. Print Settings Printer Brand: MK3 Printer: Prusa i3 Supports: Yes…
Use super glue to connect the top and bottom of the cone. The nozzle is glued to the bottom of the cyclone. Nuts and bolts attach the parts together. The bottom of the cone and the plate go on opposite sides of a 5 gallon bucket.
Simply chuck the controller on this stand and it should align itself for charging 99% of the time. A minimalistic controller stand for the GameSir Cyclone 2. The geometry of the stand should make it easier to align the controller with the…
Paired with a cheap ebay cyclone dust extractor and a 30 litre bucket, my little Kaercher WD2 vacuum handles the sawdust and chips from my power tools handily. But I found that when I was using it for cleaning up, if I was careless about…
I really liked the exosuits from nostalgic robotech cyclones. So I just tinkercaded them with lucky13's easy skins. It was fun, but time consuming. And I haven't finished the legs yet. So maybe in the summer. Also, I normally print this…
Dust cyclone for use with a shop vac. Prints in 3 parts. Press fit together. Small cutout in the base to allow room to fit an anti crush valve in the lid of the bucket when you mount the cyclone.
This is a print to increase the surface area on the bucket the cyclone is attached to. This creates more stability.
TL;DR: Sub 5 micrometer dust particle separation cut-off (density at or greater than water) Minimal pressure drop with little or no practical effect on suction power 3D-printable with only one support FreeCAD design files and OpenFOAM…
Cyclone is made from 5 parts. mainly to split printing and eliminat as much supports as possible. You have also model where Main body is connected with the PIPE. Last file added is ALL IN ONE - full model of cyclon + one upgrade pipe…
Follow us on Patreon & Instagram for the latest models. ❱ Instagram: https://www.instagram.com/sektor7_studios_3d/ ❱ Patreon: https://www.patreon.com/sektor7_studios (commercial license & more beautiful designs) Hello everyone :) Today we…
This was printed with a .2mm layer height with 5% infill. Vase mode will not work.
My remix of mgx's variant of the cyclone dust scrubber, adding the possibility to define different sizes for the inlet and outlet. I also added a thread for the standard european PET water bottles (thread from Necks & Caps Library by…
I only really use the crevice tool with my Shark Ultracyclone vacuum, and wanted something a bit narrower than DASMK3S's model that still kept the feature of the built-in charge connector. I use this bracket to mount my Shark Ultracyclone…
Cyclone dust filter and adapter for 110 tube
For the original design I liked the compact size and how it is inline for making it a part of a vacuum (Genius), but wanted the CAD files so rebuilt it as best I could. Tried to simplify the geometry and maximize areas while thickening…
Use this cyclone dust separator to collect large amounts of dust (e.g. sawdust) in a bucket while keeping your vacuum filter clean. Very helpful in a workshop! The idea is that particles are sucked into the cone, get slowed down by…
After replacing my home made dust collector with a Dust Deputy cyclone, I found that the plastic barrel I was using would collapse on itself if the hose ended up clogged/blocked. I needed a way to let off the vacuum pressure in these…
I have a small Stepcraft CNC router in my house and to keep the noise down I use a small Miele cannister vacuum cleaner with a bag and a secondary HEPA filter on a low noise setting to capture the dust and particles from cutting. I needed…
3D model cyklonového separátoru pro vysavač z Aliexpress, Temu a podobného tržiště. Model SN50T3 s průměrem hadic 50mm, který je překreslen podle originálního zakoupeného kusu na Aliexpresu. Model je bez spodní příruby.
Hello, If you like this Thing please leave a like and let me know :-) I remixed a Cyclone for the OSVAC System. Thanks to Hobbyhimmel for the great OSVAC Projekt. For the VAC i used a female adapter to easier Print, but you can place a…
TOOLS NEEDED: 3D printer (obviously) Soldering Iron (Hot glue gun can work) Screwdriver Hot glue gun (or just any kind of glue) PARTS NEEDED: Motor : https://www.amazon.com/dp/B08DG2KXZB?ref=ppx_yo2ov_dt_b_fed_asin_title M3 sized wood…
A pressure relief valve is a handy addon that prevents your cyclone dust extractor system from imploding or collapsing, if the hose is blocked e.g. by too much dust or debris. This is a mount for the pressure relief valve from Dust…
mini aca cyclone for use with the Samsung microwave blower motors all parts require supports but the supports on the rotor are optional all hardware for mounting the stator to the motor is included on the motor the rotor is intended to…
There is a new, larger version now- I'm keeping this old version up thou as it's smaller, and a tad easier to print- https://www.printables.com/model/470277-version-3-4100mm-cyclone-dust-separator Update March 29 2022 **V2.5 parts…
20.08.2023 Improved ergonomics. Printer brand: Flying Bear Printer: Ghost6 Rafts:No Supports: Yes Resolution: 0.12 Infill: 20% Filament brand: Esun Filament color: red, signal red Filament material: PLA+ Slicer: Ultimaker Cura 5.4.0 Wall…
This is the result of my imagination and guesses. I tried to make the design as suitable as possible for printing on 3d printers. I hope you enjoy it. I will be glad to hear any criticism, preferably objective.
*** Work in progress – hasn't been fully validated yet *** This model is intended to be used in conjunction with a cyclonic dust collector (such as the the Harbor Freight Bauer cyclone, or Oneida Dust Deputy), for use in a woodworking…
Der Adapter für den Schlauchanschluss hat einen Außendurchmesser von 64 mm und auf der Zyklonabscheiderseite einen Innendurchmesser von 55 mm. Er ist geeignet für die Bajonettanschlüsse von Festool, Mafell, Metabo und Starmix. Der Adapter…
Not content with the designs already out there, I designed my own cyclone dust collector to achieve the following: print quick and cheap (<400g of filament!) use minimal supports (see ‘Support Deck’ section below) integrate a vacuum…
A cyclone dust separator extracts dust and debris using a vortex effect instead of a filter. The debris is collected in its own container (easy to discard in trash) and as a result it greatly reduces the clogging of the main shop vacuum…
Cyklonový separátor prachových částic při odsávani vysavačem. Šetří prachové sáčky do vysavače. Nutno použít nádobu na prach / Cyclone separator of dust particles when suctioned with a vacuum cleaner. Saves dust bags for the vacuum…
In general, the model has become better. The number of mounting holes has become smaller. The model is easier to print. The number of problematic slopes has been reduced.
The coup de gras to muzzle report, the Cyclone is the latest in the NXT lineup. with a length of 132.5mm and a diameter of 43.65mm, the Cyclone should have plenty of internal space and mass to safely contain all expanding gasses to lower…
REMIX of "Cyclone Dust Collector" - Lower part only! Please get the upper part from here: https://www.printables.com/model/312929-cyclone-dust-collector -------------------------------------- Cool one, made an edit on the lower piece, for…
Best printed vertical with 15% infill Please share your makes!
Tried to create a cheap alternative to the metabo and starmix models. The cyclone is placed on an IKEA SAMLAs lid (11/22l or 5l) while the corresponding box can be used to collect the dust. I even did connect two in series to improve…
Happy printing, not sure if scale is giant. looked about right. happy printing.
20.08.2023 Improved ergonomics. Printer brand: Flying Bear Printer: Ghost6 Rafts:No Supports: Yes ("tree" — easier to remove ) Resolution: 0.12 (signal red); 0.2 (red) Infill: 40% Filament brand: Esun Filament color: red, signal red…
V1.1 Added extension which allows you to use two same height containers or one large container to capture dirt when stacking multiple cyclone modules V1- STL files in folder Designed for use in my milling area. Top can be cut from…
my own first try of dust cyclone not tested yet vacume hose OD = 40mm
A practical exercise in Ondsel. Split, print, use. Should work with any 35mm vac (or just modify to your needs)
Update Notes 29 August 2025 : Added new version of the Guard ring (v4). a little bit hollow, with added wings inside to add more resistance to the left and right direction button Added new version of the Dpad insert (v4). Longer part for…
This is set of hose adapters for parkside vacuum used in combination with parkside cyclone dust separator. I'm including aliexpress link for cyclone separator which a have good in my setup. Buying through an affiliate link costs you…
Create a cyclone in two two liter water bottle.
This is the second stage of my cheap and easy DIY dual-stage dust cyclone project . Click here to visit the first stage . To be honest, I estimate that for a lot of use cases stage one is "good enough" and it has a far better price to…
Here is stage 1 of my latest project: a cheap workshop dust cyclone that SUCKS :-) Stage 2 is available at this link . I recommend you to start out with this one, though! And this is what you need: a workshop vacuum to create suction a 3D…
Nozzle for sprinkler, fountain or mist sprayer
I like the Makita handheld vacuums, but the filters clog quickly. The cyclone attachment resolves this, but makes it a bit unwieldy. This design adapts the cyclone attachment (https://www.makitatools.com/products/details/191D70-5)…
This is a right angle fitting that attaches to the top of a Dust Deputy cyclone separator. This fitting makes it less likely to kink your vacuum hose. For standard 2 ½ inch vacuum hose. I printed it in one piece in PETG with supports. You…
I think it's fantastic
Remixed for 1.5" vacuum hose and tested. Print instructions Category: Tools
Grenade holder for the Airsoft Innovations Cyclone grenade. *UPDATE 17-02-23: Added a longer version (Grenadeholder L) Instructions: Print 2x Grenadeholder and 1x Vestmount or 1x Grenadeholder L and 1x Vestmount. You also need 2x M3 Nuts…
DASMK3S's model does a great job holding the vacuum, but I didn't like seeing the heads of the screws and the power plug wiggled a bit. I designed a couple press-fit pieces: one to cover the mounting screws and one to hold the plug in…
Most of models available for download are created for 2 ½ and 4 inches hoses and none of them is a parametric model. So I decided to create a dust separator that fits to 3 inches dust collector systems. It is a bit large, and maybe you…
This product is a separator for cleaning the air from debris and fine dust . Everything was done by inspiration, I just imagined myself as a speck of dust on this planet =) CFD: https://www.simscale.com/projects/SLAVA/sl_st_cyclone_3-03/
Various adapters for machine vacuum cleaner connection
An adapter based on Pazzah's existing work that connects RoboBear's dust cyclone directly to a Ridgid shop vac hose. The fit is tight and might need a little sanding or a deburring tool to get the openings just right. Print with the…
I do a lot of wood working and I recently bought a Fein shop vac to replace a Craftsman that I had had for 20 years. The Craftsman was still working, but it was deafening, at about 98 dB. The Fein is about as about as loud as the vacuum…
Inspired by his more melee type arsenal from the comics, here's the sword, holder and a display stand for WFC Kingdom Cyclonus. The sword sports a brutal katana-esque look and for this particular take on it, designed with a slightly…
This Vacuum Valve can prevent container collapse due to high vacuum pressure, especially when the suction hose becomes blocked. By adjusting the spring preload using the screw, this valve ensures closure during regular operation while…
Cardinal Sin Red Cyclone Fixed Blade Knife Knife inspired by the M48 Cardinal Sin Red Cyclone, blades with a three-cut spiral design. Introducing the M48 Cardinal Sin Red Cyclone inspired knife, a spiral masterpiece that redefines the…
Hose adapters for Thomllama's Cyclone Dust Separator for 2.25" (58mm) inlet and 45mm outlet hose. Inlet adapter is straight, 37mm O.D. to 58mm I.D. Outlet adapter is 90 degree, 37mm O.D. to 45mm I.D. Both were created using the Parametric…
Trotz des wiederverwertbaren Beutels, den ich mit einem 3D gedruckten Adapter an den Staubsauger anschließen kann, fällt mein Schleifen des Betons und des Fliesenklebers so viel Staub an, dass das Entleeren des Beutels länger dauert, als…
A replacement/replica weapon for Transformers G1 Cyclonus. This is not an exact replica to the original toy accessory but is close enough. Modelled from reference photographs as a replacement gun for my personal Cyclonus figure. The…
A cyclone dust collector that can deposit dust into a bottle. For prototyping, we are currently using a 0.3mm layering setting, but we may need to switch to a finer setting to maintain suction power. Tackling our worries about support…
A simple adapter for quick installation of the original Karcher WD3 vacuum cleaner hose. The connection of the elements is loose enough that insulating tape could be used to seal it. Printer settings: 0,2mm layer height 4 shells use tree…
Everything threads together and it has space for a HEPA filter at the outlet component. This part of the design has not been thought out very well so I will likely implement a slide in attachment for the HEPA filter for future use. There…
I remixed my previous model to be printed in 256mm printer beds without cutting each part. The edges were removed and groves were inserted to allow gluing the parts instead of using screws. I increased the botton funnel to 70mm hole to…
Printed a Cyclone for a hard PET bottle (in this case its Sprite) to glue in. It has an efficiency of 99.87% for 25µm corundum which is a lot more than i would have guessed! Just glue the bottle in and adapt it to a bigger (and stiff)…
These are female threaded inlet and outlet made for Dronnn's cyclone separator. https://www.thingiverse.com/thing:2829268 I chose to go with female threads since it offered more flexibility for the oddball collection of hoses that I have…
In the picture you can see the following things in addition to the adapter, which is the blue one in the top middle of the cyclone: Cyclon from thingiverse (grey): https://www.thingiverse.com/thing:2829268 Kärcher vacuum hose adapter…
This is a remix from: https://www.thingiverse.com/thing:5100235 by 3D_Blue_Prints I printed the previous version to separate 15" planner chips but it clogged every time. I removed the bottom section and added a flange to attach it to a…
Cyclon separator Click here for details https://ishigame-machine-technology.net/IMT/?p=1830 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: Infill: 40% Filament: PLA+ Category: DIY
Project Plan: This project aimed to create a telescoping fidget device by utilizing sketch offsets and drafted extrusions/cuts. The sketch must have begun with a constraint box (center rectangle created from the origin). Our outermost…
This is a case for the Altera Cyclone II EP2C5T FPGA board EDIT 08-09-2019: Updated design, now the holes and inline with the ones on the PCBs, download v5. Print instructions Used the enforcer slab option for the support region (the JTAG…
Best grinder in the world, have printed dozens for my friends. Its a shame the original creator regretted designing it. The other design still around has the wrong files uploaded so it doesn't work, which is sad cuz the redesign seems…
