Liczymy pasujące modele…
In one corner of my section there stands a black barrel that I think the previous owners intended to use as a rain barrel. As the forecast for this weekend was for rain, I thought I'd hook it up. As I have a 3d printer, I elected to print…
This piece can be inserted in a rain pipe to fill a rain barrel on the side. If that barrel is full the water continues to go vertically down the pipe. This model is made for a DN75 (outer diameter 75mm) pipe, but there are parameters in…
Compost Commander: Urine Diverter & Toilet Insert Take control of your throne like a true eco-maker! This 3D-printable compostable toilet insert diverts liquids like a champ, keeping your solids dry and your compost pile happy. Great for…
Rain water collector diverter allows you to choose whether you want to send water to the tank or to the sewer Print in White PETG for 80 mm tube (2 screews 4x40 to fix handle) Optimized print profiles for Bambu Lab printers available…
Why Needed After I mounted the air exhaust passage that came with my Midea MAP08S1XWGR-T , part number 12120600A23603 and extended the exhaust hose to reach it, I found that the air blew straight out the doorway, cooling the next room,…
Replacement plastic gear for Omnires MURRAY water diverter from MU6132 set. It's a close fit when printed on a SLA printer (prints fine even without being angled, but that may require some sanding (of the bottom/top part only)). Attached…
Easy Snap-On air diverter and shield for the K2 Plus heater to direct it away from the 3D print area. Looking to the few designs out there I did not like the full implementation. 1 - The air should be directed down - away from the…
This piece can be inserted in a rain pipe to fill a rain barrel on the side. If that barrel is full the water continues to go vertically down the pipe. This model is made for a DN75 (outer diameter 75mm) pipe, but there are parameters in…
My bath/shower mixer tap's diverter failed to do much. No water pressure in the shower. So this part solved it. SHOULD BE MOUNTED THE OTHER WAY AROUND FOR BEST SEALING. Onshape link:…
This model friction fits right over a 23.5 mm aerator/filter. No glue or threading required. Print conditions: A brim is highly recommended Atheistically, the seam is best when on the back of the part the downloadable 3mf does this (and…
Update 2024-05-15: There is a new version that includes two side ramps for additional rainwater collection. It's available for the 2"x3" and 2 5/8" × 2 5/8" sizes so far. Update 2025-03-04: Added a “bare” outlet adapter to use as a base…
This design is used to collect rainwater from a gutter. The input side is compatible to the NW35 gutter pipe size. At the output (overflow) you can connect the DN50 pipe. The rainwater will be forwarded through a ¾" hose compatible…
I made myself corner water diverter as because of poor design current water divert does not keep all water away from wooden base, especially in corners, wood under does not like to be wet! Can be glued in place using silicone or montage…
The original part breaks, warps, and sticks. This improved part sticks less and should hold up better. The fillets and struts are designed to reduce turbulence and thus noise. Apparently PETG holds up better than PLA in chlorinated water.…
print in something heat tolerant, this thing sits pretty close to the hotend. attaches to the lower two screws that hold the toolhead board in place. this goes very near the printed part and may need some fine tuning depending on your…
This is a quick and dirty trash diverter for a downspout. The initial version takes a 2"x3" input, and outputs to 4" rounds. As with all 3D prints you use outside, you either need filament that can handle UV or you need to paint it with…
We purchased a Teca AHP-1200CPV chill table since Bioquip is no longer selling equipment. The fans on the AHP-1200CPV are very powerful and will blow around anything next to the chill table. These vents will divert the air behind the…
These are small brackets that magnetically attach to the cover of an air vent to help direct the airflow. They are particularly helpful in rooms that struggle to heat up in the winter with the vents toward the ceiling. In addition to the…
Drill holes all the way through the fan shroud in the threaded nuts where the stock fan mounted with a 1/8" drill bit (see pictures). Install M3 heat-set insets on the side that faces the hot-end. (I used 10mm long inserts) Printed the V1…
A rainwater diverter for 100x50 downpipes. It's designed to avoid cutting down on the cross-sectional area of the downpipe so even when the tank is full the downpipe still has full capacity. Has an adaptor on the side that can be easily…
The LED surface mount lights in my office didn't have a diverter, so I made one. Uploading to share based on a few requests. Including the .f3d file in case you need to modify the mount to fit your light.
A printed version of the diverter for an A&A In Ground Pool Cleaner. Part #230152 It is easiest to print just like it is in the .stl but it will be stronger printed on the side with supports so the layer lines are running in the same…
Tired of having a sweaty warm mouse hand after working just 30 seconds with your HP G5 ZBook? I was. So now the air will have to go straight up and thus miss my hand. Laptop is still able to close without smashing the screen. Diverter…
***Remix file uploaded*** ***Version2*** Airflow diverter to force airflow upward to the spool. There is about a 15 mm gap under the rollers that doesn't do much for drying, so I made a diverter to force warmed air upwards to the spool…
My mother's bath tub faucet had a diverter stem that refused to stay in place. She was previously using a piece of oxygen tubing, and this proved easier to use. I made this fitting out of flexible filament (ninjaflex) with my MK4S, 0.6mm…
I created this because the handle set screw no longer held and the handle came off. Then pliers were used for a while so the shaft was in rough shape. This has teeth that grab the plastic shaft without using pliers.
Diverts air from a SpacePak HVAC system at a ~90 degree angle instead of straight down onto people. Printer Bambu Labs P1P Filament PLA Matte (Ivory White) from Bambu Labs Nozzle .4mm Supports Yes, Threshold Angle: 30 Duration ~1 hour 40…
The De'Longhi Magnifica Start has an issue with the steam triggering the touch screen button power, which stops the latte and cappuccino process. Made this tinker cad it's my first model and I attached it to the De'Longhi icon. I attached…
I continue to use this blower and mechantronics fan combo, to increase the compatibility with my printer (ReDuplicator MK3x) I needed the diverter section to have vents, as the freely open side is very close to the x carriage mount. Print…
Adjustable air diverter similar to the ones at Home Depot. Partslist Printed Parts Clip LHS x1 Clip RHS x1 Diverter LHS x1 Diverter RHS x1 Purchased Parts M3x6mm Button head cap screw x6 M3 Hex nut x6 ½" x ¼" x 1/8" Rectangular Magnet x4…
I wanted a stronger and more accurate back plate for the Piper air vent diverter that I had already found published by Pierre. I measured actual backing plates from a PA-28 Warrior and sketched/modeled them in Fusion360. I did not like…
This is for an old Jacuzzi pool sand filter diverter valve model 24LT3 from the mid 1970s. I don't expect much downloads but I hope it helps someone save their functional filter for another decade since parts are no longer available. The…
Computer-optimized components for the original Wind Cannon are provided, which can increase airflow velocity by about 40% compared to the previous versions. Exit airflow velocity can now reach near 30 MPH. Additionally, the finned…
I tweaked the excellent model to connect to some FloPlast Overflow Pipe 21.5mm Internal diameter.
Compost Commander: Urine Diverter & Toilet Insert Take control of your throne like a true eco-maker! This 3D-printable compostable toilet insert diverts liquids like a champ, keeping your solids dry and your compost pile happy. Great for…
Rain water collector diverter allows you to choose whether you want to send water to the tank or to the sewer Print in White PETG for 80 mm tube (2 screews 4x40 to fix handle) Optimized print profiles for Bambu Lab printers available…
This is an automatic overflow Rain Barrel Diverter for 3" PVC Pipe with a 1.25" side take-off that fits 1.25" sewer pump drain hose. My rain barrel had an opening that fits 1.25" hose and I couldn't find a design that used 3" PVC. Water…
Why Needed After I mounted the air exhaust passage that came with my Midea MAP08S1XWGR-T , part number 12120600A23603 and extended the exhaust hose to reach it, I found that the air blew straight out the doorway, cooling the next room,…
added a small cone to the inside to better divert the water
Protect your furniture from steam, put it on top of the Thermomix!
NEW Version 2! We have a little whale cover for our bathtub spout to protect baby from hurting themselves if they bump their head on it. Problem is my fat fingers can't pull up the diverter knob anymore, so I made this quick simple thing…
Sylvan pools have a 2.75" discharge into the pool. They have a 90-degree diverter that causes a “swirl” in the pool. This diverter fails after enough years, and appears to be unavailable. This is a replacement. The dimension/shape of the…
Rain Collector / Downpipe Diverter for Biohort AvantGarde Garden Sheds & Garantia Rain Barrel Hose I modified the excellent design from varnerrants https://www.thingiverse.com/thing:2965677 to fit the Biohort Avantgarde downspout and can…
Will probably have to cut the part in multiple sections and glue it together if you have a standard sized printer. No supports needed. I would recommend PETG as, depending on the location in relation to the furnace, heating may warp PLA.
ho creato il deviatore in due parti per ridurre al minimo la necessità di supporti e per poter avere un ugello più lungo possibile per la mia stampante. Le due parti sono ad incastro, ma volendo si possono incollare tra loro (ovviamente…
Replaces Waterway 519-4060, 550-1500 parts for a hot tub water filtering system. To ensure tight fitment with the filter cartridge the conical part is slightly oversize. Heat the cone portion of the plate in a cup of boiling water and…
Self cleaning Leaf filter / Rain water catcher for downspout gutter, that use Coanda effect Original design by NeedItMakeIt . I redo it with print in one part (to get rid of the plexiglass and simplify joint and assembly), Spiral angle is…
These are the spacers modeled after the original Hayward PSV diverter valves. Some aftermarket rebuild kits are generic and missing the spacer that's supposed to be included for Hayward. I found this out when the ones my pool guy was…
I was having a problem that the outflow hose from the washer was overfilling one side of the sink. The drain pathways for the sink are pretty confined so it slows the flow of effluent into the drain pipe below. The diverter divides the…
I tightened up the slot so the diverter would quit falling out when I pulled it up to take a shower. I re-used the original rubber seal.
This is a push-on doodad for projecting water outward from a faucet. This makes it easier to actually wash your hands in the bathroom sink. Most lavatory faucets wind up pouring water 0.5-1.5" away from the back of the basin, which makes…
Summary: Didn't like steam going at high speed into my cupboards, couldn't find steam diverter that would work for Ninja Foodi Max 14-in-1 (OL750) so I created my own. It is not very fancy, but does the job, and it rotates so you can…
Remix of the original diverter. Decreased height by 1 mm, increased width by 0. 8mm, and added a back "foot/tab" for placement stabilization as suggested by a user comment. I also made it hollow inside to save filament and time.
Replacement plastic gear for Omnires MURRAY water diverter from MU6132 set. It's a close fit when printed on a SLA printer (prints fine even without being angled, but that may require some sanding (of the bottom/top part only)). Attached…
Easy Snap-On air diverter and shield for the K2 Plus heater to direct it away from the 3D print area. Looking to the few designs out there I did not like the full implementation. 1 - The air should be directed down - away from the…
This marble run piece will split marbles entering it into two different paths. Multiple of these diverters can be connected to send marbles onto as many different paths as you want! This should work with almost any marble run set (ours…
Material Used : PLA+ 2.0 Note : If you notice leaks through the device, then it might need sealing. Not had the issue myself, but you could try spraying the outside and inside with "Clear Lacquer". The same applies to accessories.…
Jeep JL Wrangler Front Windshield Air Diverter Improved airflow for the JL Wrangler front windshield to get corner areas that don't defrost or fog up. This model was based on the JK Wrangler diverter that was found on Thingiverse…
Diesel heater duct diverter, 60 mm, allows adjustable airflow mixing or full diversion between outlets with manual control lever. Separated into sections for cleaner printing. Printed in PETG 75% infill 4 walls and the speed recommended…
My bath/shower mixer tap's diverter failed to do much. No water pressure in the shower. So this part solved it. SHOULD BE MOUNTED THE OTHER WAY AROUND FOR BEST SEALING. Onshape link:…
After searching for a while I was unable to find any decent steam diverters for the ninja foodi. As I wanted a dragon I remixed this awesome red dragon bust into a lower poly version with a base which fits over the steam exhaust of the…
After searching for a while I was unable to find any decent steam diverters for the ninja foodi. As I wanted a dragon I remixed this awesome red dragon bust into a lower poly version with a base which fits over the steam exhaust of the…
These two fittings thread together to form a tarp leak diverter. This allows one to take a tarp, hang it below a ceiling leak, and put a small hole in the low point, silicone this fitting through the hole, tighten the nut, and attach a…
This float valve is designed to block debris from entering your rain water catchment system from your first flush diverter. To use this print you'll place the ring between the Tee connector and 3" pvc pipe with the lip seated inside the…
This model friction fits right over a 23.5 mm aerator/filter. No glue or threading required. Print conditions: A brim is highly recommended Atheistically, the seam is best when on the back of the part the downloadable 3mf does this (and…
The return hose on our Coleman 14' x 42" above ground pool shoots the stream straight out into the center of the pool. Any pool this large (or larger) really should have the return flow diverted to the side, away from the inlet so that…
This spout is a 1:1 replacement for the Algreen Products 81052 Rain Barrel Deluxe Diverter Kit Black. Best to use TPU to print with 100% infill.
This is a rain spout diverter for a 3x3 rain downspout. I had bought a diverter, but it was sized for a 3x4 and I needed 3x3. I was considering cutting down the first one and trying to glue it back together, but re-thought that process.…
The shower head diverter valve was too high for my wife to reach without a stepstool. This fixes that problem! Print with supports. 1hr 14min print time. V2: I made a few changes. I increased the length of the rod by removing the hook on…
Enhance your water circulation with this custom-engineered, low-profile water return jet and vortex diverter. Designed to optimize fluid dynamics and maximize surface skimming action, this model is a robust replacement for standard basic…
Porting from Thingiverse. Credits to jroger. Original licence respected This is a simple rain barrel diverter intended for Ø80mm gutter pipe. It may be adapted to many pipes diameters by editing the top and bottom cap in the sketchup…
This is designed to clip on sponge filters to divert the flow and also make them quieter. This makes a sponge filter create flow in the tank rather than just bubbles going upwards. It specifically clips onto hygger sponge filters but may…
Shower diverter did not want to stay up at lower water flow so i made this clip to hold it in open position. It works very well. Bathtub faucet manufacturer: "hansgrohe" Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No…
Bit of a tight fit at 12.8mm but you can be sure it won't fall out. TPU highly recommended. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.20 Infill: 10 Filament: Yoyi TPU Red Notes:…
An InstantPot steam diverter remix of a prehistoric minion. Faces to the left when the valve is open. Original design by Alsamen Print Settings Supports: No
Just a simple trash diverter for a downspout. Print Settings Printer: Micromake D1 Rafts: No Supports: No Resolution: 0.33 or as large as your nozzle allows Infill: Solid via 2.0 mm shells (5 shells with a 0.4 nozzle) Category: Outdoor &…
The Bissell Pet Hair Eraser is a corded hand vacuum with limited mobility but a lot of suction power. The suction is great for pet hair, but the side exhaust is so strong it creates extra work. The exhaust is Blowing in all directions…
This is my first practical design of the filament diverter I needed for the wall mounted filament holders that I created. Inside my enclosure there is space for 4 spools per side and I thought it would be nice to have something that…
rainpipe water diverter. its a work in progress but it works main function is to catch water and not cause a vacuum in the rainpipe because its a closed off section its suited for standard 80mm pvc pipe including the sleeve to fit and…
These are inserts inspired by https://www.instructables.com/Rain-Barrel-and-Diverter/ for a PVC 4-in x 2-in dia x Hub 45-Degree Combination Wye to turn it into a diverter for a water collection system. The bottom portion resembling a cap…
This fixes the problem of the Makita Trim Router blowing the air downward in a CNC machine. It also acts as a muffler to dampen the high frequency sound coming from the air, motor, and bearings. The air diverter is held in place by the…
I needed a 90deg diverter for the exhaust vent on the enclosure. Uses the existing port screwed into this diverter. Material: PLA Supports: Yes Additional Parts: M4 x 8mm (used 4 of these to secure existing exhaust port)
I needed a downspout diverter for a few rain barrels I was installing. I found the original great design, but it didn't fit my 3"x3" downspout pipes, so I remixed it. Thanks to the original creator for the original design!! Print Settings…
Dust boot for Bosch 1617 router with air diverter and magnetic dust ring. 4" and 3" vacuum hose adapters are included. The air diverter (center section) can be omitted if not needed. In that case, use M6x16mm bolts instead of the M6x35mm…
Looking for an efficient rain water diverter on a pretty busy 100mm (DN100) downpipe at my house I found that the few models that came close to my expectations were in the price range of 80 to 180 Euros. So I decided to make my own. Due…
This is an exhaust chute diverter for a Dewalt Miter Saw, and it can work for other saws as well as long as the chute's OD (outer diameter) is 39mm. Notes on Usage: Print 2x 40deg elbows and and 1x 40deg fan-out (no vacuum required) If…
Glass Shower stall door was spraying water out onto the floor. It was missing the diverter at the bottom. Could not find the correct replacement size at any of the big box stores. Printed 3 to span the width of the door. No more water on…
Needed a hose diverter, so printed one Category: Outdoor & Garden
Is your tub/shower spout diverter broken due to years of water wearing it down? Is your tub/shower combo relegated to the dirty duties of just a bathtub due to lack of water elevation? No more! Simply 3D print this handy repair tool for…
Holds the shower diverter up so that we can use the shower on any water pressure. Category: Bathroom
Back during the covid lockdown here in Michigan I could not buy a replacement shower diverter after mine broke. The hardware stores were closed so I designed this diverter and used the old rubber cup seal from the original but you can buy…
Unfortunately the exhaust on the t480s is on the right side, while having warm air blown onto your mouse hand may be fun in winter it definitely isn't in summer so I decided to mitigate that. From my testing it did not decrease cooling…
I keep reptiles and needed some kind of baffle / diverter for the fogger tube, so I designed one. :) If you would like to support / throw me a dollar for my design, please feel free to go here and get the design files:…
EDIT 7/11/22 : I found that after 2 years of use, enough dirt and crud had collected to fill up and clog my gutter. I have shrunk the depth of this diverter, hoping that it will give a clearer path for any dirt that finds its way into my…
Exhaust diverter for Dyson V8 absolute. ive seen many on here that divert it back towards myself but i get annoyed with the air. this model diverts it forward, may blow dust around if using a short attachment but i personally dont use…
Remix to divert exhaust straight back. I was looking for similar files and liked the minimalist design, however I did want the exhaust to go back as I do use the short attachments. I was finding the regular exhaust was blowing debris…
This plug fits the hole created in a downspout when using the EarthMinded Rain Barrel Diverter and Parts Kit. Useful to keep water from leaking out of the downspout during winter or anytime the rain barrel isn't connected. Fits holes 54mm…
Wanted something to catch water drips and keep them off the counter. Printed with TPU
