Liczymy pasujące modele…
Hello everyone! I designed these 3D-printed supports for 30 mm diameter springs, intended to isolate the seat, enhance the performance of the bass shakers, and minimize vibration transfer to the rest of the simulator. The 3D support…
I was getting fed up getting poked in the leg when out geocaching so made a cap for my set of I sharp tweezers. there is a hole for a lanyard if you so wish to have one too. I printed this in PLA but would be better in PETg or maybe even…
It is often necessary to isolate or "lift" the studio monitor speakers from your desk or stands so they don't resonate, don't act like a secondary (unwanted) source of sound. There are some isolation foams you can buy for cheap which…
The cooling fan on my Tronxy X3 resonated through my table and floor in my print room above my living room providing a constant hum. Thought I hearing things for a while. I developed these feet to reduce the vibration and quiet my printer…
In addition you need 3 screws M4x40 DIN912 and some stripes of flexible selftapping isolation (10 mm thick and 75 mm long).
It is often necessary to isolate or "lift" the studio monitor speakers from your desk or stands so they don't resonate, don't act like a secondary (unwanted) source of sound. There are some isolation foams you can buy for cheap which…
Vibration Isolation Model: https://www.thingiverse.com/thing:3794194 (45x45mm version) Additional Hardware: - M3 Heat Set Insert The top plate has two versions. One for a 4mm heat set insert and another for a 6mm heat set insert. Each to…
Extra Materials : 4x M3x6 Heat Set Inserts. 4x M3x6 Socket Head Screws
This project is a custom modification for the Anycubic Kobra S1 designed to separate the electronics compartment from the print chamber . The main goal of this modification is to: Significantly improve chamber airtightness Ensure very…
Aus einem aktuellen Anlass habe ich diese 2 Modelle hier erstellt. In meinem Heizungsraum habe ich 43mm und 57mm Schaumisolierung verbaut, diese beiden Schablonen haben mir die Verlegung erheblich erleichtert. 90° Schnitte auf Gehrung,…
Description: A direct replacement for the Sony PVM-14L5 rubber isolation feet. This will also fit other PVMs such as the 20M4U and 1954Q. Printing: Foot: Use FlashForge ASA or equivalent alternate. 0.4mm Nozzle, 0.2mm height, 50%+ infill,…
Heyho My kidz love the Emil Glas bottles. So we bought some spare ones and I printed some protection/ isolation encasings so they can use them with a reduced danger of damage or temperature change :) In comparison to the original foam…
BIOHAZARD DO NOT ENTER ISOLATION PROTOCOLS IN PLACE, SIGN Category: Signs & Logos
STOP, DO NOT ENTER, ISOLATION PROTOCOLS IN PLACE, SIGN Category: Signs & Logos
Made these TPU isolation feet for the at-lp3 because the ones that come with it are too short. This uses stock screw, just pull off old rubber foot and feed screw. Can still use plastic portion as seen in picture. 4 walls 25% cross…
Isolation Enclosure for Polymaker Polydryer A shell to clamp around the body, holding insulation-material in place, so the filament drier is more efficient and can be used at colder outside temperatures. Test printed with pla - holds up…
Made for SVS Subwoofers but can be used with others aswell. Needs a ¼-20 bolt, 15-20mm length I used ABS-GF and TPU 90A to print these parts. For feet i used 2 walls with 8% gyroid infill with 90A TPU, that gave good results with SVS…
My original plan was to use 4 of these isolators between a platform for my vinyl player and a table, but I didn't finish the project. Should work with any squash ball, I tested using these .
My printer sits on a mostly empty entertainment console and vibrates the thing like a drum. I saw this model on ALL3DP's suggested TPU prints list and gave it a go. This does not replace the printer's feet - they just sit securely in the…
washer to mount a transistor on a heatsink without electric contact; you have to use an electric isolation on the plane side of the heatsing i.e. mica plate or tape.
This is a modification of the lower parts and vacuum manifolds for the Carvera Back Panel Isolation Mod by Fae Corrigan. You will still need the upper parts from Fae's mod located at…
This model is a replacement for the stock top plate that comes with the s500 frame kit. It includes vibration isolation for an autopilot / flight controller board and provisions to mount a raspberry pi companion / flight computer for…
I was building a NAS out of a Thinkstation M920Q and the ASM1166 card was touching some metal when inserted into the PCI-E slot. So I designed a snap on isolating backplate. It holds itself on purely by friction. If you want it to be held…
Vibration Isolation Dampening Feet There are two manufacturing options for producing these dampening feet: Direct 3D Printing – Utilize TPU or a similar elastomeric polymer. Mold and Cast – 3D print a mold and cast the feet using…
My first HueForge project for the game Alien Isolation; I'm very happy with how it came out. This print uses 6 unique filaments. For this project I use a defunct brand of filament, so make sure you use a comparable filament for color and…
Shrimp Jail v1.1 Lock those buggers in! The perfect hanging isolation chamber for misfit shrimp, fish, snails, and other up-to-no-good aquarium residents! Also great for pregnant fish, guppies, and other moms that need to be separated…
Overbuilt DIY Air Filter for Enclosures Whether you're filtering out laser engraver fumes, solder smoke, or mystery haze from whatever that last print was made of, this DIY air filter is built to take it. Designed for enclosed spaces like…
I love these isolation pads but, when i upgraded my prusa to the bear 2.0, my existing mounts didnt match. I remixed the mounts to fit using the original files, its also nice to have the feet mounted to the frame. Print instructions…
Lumenier QAV-PRO 3.5" Mini Whoop - Immortal T Crossfire Mount and DJI O3 Air Unit Isolation Pad
KEF floor isolation feet for metal spikes. Inner diameter is 8mm. Use 1 to 3 8-9mm washers inside the shaft to protect the bottom from pucture. I used two 9mm washers inside the shaft.
An isolation style foot for the SV08 which effectively dampens the vibrations to and from the printer. You can customize its stiffness also, simply by changing the number of walls and infill. I print these in Orcaslicer, and use a…
An isolation style foot for the SV08 which effectively dampens the vibrations to and from the printer. You can customize its stiffness also, simply by changing the number of walls and infill. I print these in Orcaslicer, and use a…
This is a very simple model, just print 4 of them and slot them into the feet of your printer. You can also stick some felt or rubber stuff to the bottom. Lay the model on the side, this way there are 0 overhangs and it should print…
This is a temporary battery isolation switch for certain model Hitachi Excavators. It does run the RISK of breaking off in the battery isolator if layers aren't printed solid and great adhesion. If the model works for you find us online…
This is a two-part model using rubber non-slip shelf liner (checkerboard, not solid) between each layer cut allow a folded over once section to fill the entire cup on the main printer foot component. The Ender 3 would send loud rapid…
Just some simple feet to raise your eufyMake E1 UV printer off the surface. Can print in TPU to also act as simple vibration isolators. I printed mine with 2x 0.4mm walls and 15% tri-hexagon infill on top and bottom 25% and 1x 0.6mm wall…
Isolation feet made with small bouncing balls like these: https://amzn.to/3KEyVT9 Category: Hobby
You can turn a regular through hole crystal in HC49 package into a SMD variant using this isolation pad.
ABYC requires AC breakers with exposed wiring to be isolated when a combined AC/DC panel is opened. My Catalina 400, like many older boats, doesn't have a cover for the AC breakers so I made this one in Fusion. Attaches to the wood frame…
I recently purchased a pair of SVS PC2000 Pro down-firing subwoofers, which come standard with the SVS SoundPath Isolation feet installed. Due to my thick carpet, the driver cones were very close to the carpet. This model acts as a 10mm…
isolation cap for m6 nut/screw battery terminals
Vibration Isolation Model: https://www.thingiverse.com/thing:3794194 (45x45mm version) Additional Hardware: - M3 Heat Set Insert The top plate has two versions. One for a 4mm heat set insert and another for a 6mm heat set insert. Each to…
One of our fish was getting bullied by the rest, and we wanted to keep him separated for a while so he could have a chance to recover. We found the “Aquarium Critter Isolation Box” from @ColoGeo_143273, which was exactly what we wanted,…
Allgemein Verschiedene Durchmesser (Rockwool) 45° Schräger für 90° bogen V-Schnitt für T-Stück mit markierung für Mittelpunkt der Gehrung Schneiden mit Cuttermesser 3D-Druck Gedruckt in PETG 25% infill ohne Support General Various…
We had with our Z10 Jura coffee machine a Milk Cooler RM380. Its seems they last for 3 years. Bit of wast and hardly reparable. The good news is that the Stainless steel container and tubing in good shape can be reused with these two…
Isolation "plate" between backplate of LGA 115X sockets and it's motherboard PCBs. Used it with stock HP cooler PN: 644724-001. It's metal backplate is usually glued together with PCB by double sided tape so it's naturally isolated from…
10"x24" ID x 1" Angle Flange for EPDM / Canvas isolation connector. Accepts 12mm x 3mm neo magnets. Used to isolate / decouple an IB dual opposed subwoofer mounted in the attic from a wall.
Die Schutzhülse dient als thermische Isolation, da die Kartuschen bei der Anwendung sehr kalt werden. Kann für Kartuschen mit Ø18mm angewendet werden. Materialempfehlung PETG z.B. für Kisag Rahmbläser
This is a companion piece to Forker45's excellent vibration isolation feet that utilize the speaker sound isolation feet. They can be found here: MK3S+ Vibration Isolation Feet by Forker45 | Download free STL model | PrusaPrinters They…
Simple print made in Prusa Slicer. Only additional materials needed are memory foam and felt pads. memory foam should be 1cm (0.4") thick. Cut to 18cm x 26cm and place inside tray. Felt pads can be any size, I would suggest putting a few…
Extra Materials : 4x M3x6 Heat Set Inserts. 4x M3x6 Socket Head Screws
To be used with Gould Shawmut Fuse Block, NH-00-EP, or compatible ones. Useful to avoid short and following MEGA sparking effects :) Printed with PLA, but it would be nice to print with flame retardant filament (UL94 V0 spec).
This project is a custom modification for the Anycubic Kobra S1 designed to separate the electronics compartment from the print chamber . The main goal of this modification is to: Significantly improve chamber airtightness Ensure very…
Aus einem aktuellen Anlass habe ich diese 2 Modelle hier erstellt. In meinem Heizungsraum habe ich 43mm und 57mm Schaumisolierung verbaut, diese beiden Schablonen haben mir die Verlegung erheblich erleichtert. 90° Schnitte auf Gehrung,…
Keep your tiny buck converter safe and isolated from the rest of the circuits of your printer. I added a hole for adjust the voltage Just print them as downloaded, no supports needed I have made this case for the item linked bellow (the…
Designs I prepared 3 Designs for you: A) Spare Parts + Nut Holder: 5 Pieces - Isolation Top + Bottom + Base + Nuts This design lets you carry all "original" parts with you in case you are not allowed to use this modification on a…
Just quick model, so I do not get any shorts. I am using this board to automate some stuff on my electronic workbench. https://www.aliexpress.com/item/1005008369737053.html This is a piece of plastic to isolate the bottom. I left the…
Printed standing upright in (Amazon) TPU (exclusive mode) for secure fit on the handle of my DeBuyer CARBONE PLUS 28 cm steel pan (5110.28). Just push it over the handle and give it a harder hit on the foor or some hard surface to push…
The spacers in my opener went out, so I fixed it, for next to nothing, 3 hours later. OEM kit is about $10 with 5-7 days shipping. To get them close to the OEM "durometer" or function of the original spacers (soft start on the plastic…
I needed a microphone isolation shield to help control reverb and external noise when recording voice overs. None of the available solutions were large or flexible enough for my application. I also wanted a system that I could reconfigure…
Two interlocking TPU spacers cushion each mounting point, completely isolating the spring from metal washers and the frame to prevent paint wear, rust, and squeaks. Features: Paint Protection: Flanges sit directly between steel washers…
Guide for cutting pipe isolation. The center line will help with cutting T joints in pipes. Please use the following parameters to adjust it for your needs. - Angle 1 ( default 45 deg) - Angle 2 ( default 22.5 deg) - diameter of isolation…
Tape holder for isolation tape with scad design parametric
Replacement for Fractal Define R5 HDD isolation grommet, to be printed in TPU, based on original. I recommend splitting it in half, as middle gap is small enough for TPU to merge the gap and make putting it in the slot impossible.
These were printed with a .15mm nozzle in order to make the thin walls. Printed with nylon, since it can be subjected to considerable heat from the power transistors in the reciever.
Used very nice original .STL files to guide re-drawing in Onshape so that a load bearing web could be added to the side mounted foot brackets. The bottom mounts are the same as the original. .STEP files for all parts are included.…
I originally posted this on Thingiverse back in 2013 after I sketched one up to get me out of a tight spot. See https://www.thingiverse.com/thing:166965 I've slightly amended the design here so it should be a better print. There is a…
The sensor was reading the actual humidity inside the desiccant holder, not the environment. This isolates the sensor from the desiccant.
Was going to print out of TPU, but saw other various models with a less stout attachment and a shorter foot. This will elevate the printer 58mm and should allow for a 120mm fan installation under printer and plenty of room for airflow. I…
A bottle cover that keeps your beer cooler for a bit longer if you want to drink it later. The walls are about 10mm. Bottles differ a lot so this one fits to most Czech beers, some German too but no guarantee. The bottle used for the…
Feet for audio equipment to isolate vibrations. If you need help with printing? Have questions about the designs? Want to keep up with what we're prototyping? Join our discord https://discord.gg/fb4HdDvErF Additional Affiliate Links if…
High voltage curve tracer , isolation tester Some time ago I ordered 230VAC LED modules, consisting of an aluminium coolplate and electronics, separated only by a thin layer of isolation. I wanted to check the safety of the isolation, and…
This is not the most flush design, it leaves some gap to provide isolation. I used 2 clips of 1cm out of ABS and it turned out super nice at the first try. You can simply scale up/down Z to your desired dimension. The hole is there to…
neatly organizes the AC cable of my 3 A Philips variable isolation transformer
CoolFinger Hack preventing you from steamburning your fingers, letting you steamburn your tongue instead. Filament used: Prusament PETG Prusa Galaxy Black Prusament ASA Prusa Orange Printer setting: Layer height 0,2mm Perimeters 3 Infill…
I created these mounts to fit the Hudson Hi-Fi 1.5” Bigfoot Isolation Feet as I found that when using the squash balls, the squash balls would get squashed too much and most of the weight was at back which created a slight tilt backwards…
For my trip to Norway in winter 2019 with my campervan, I developed a holder for XPS foam over my Seitz S4 windows. This Isolation worked perfectly and I had never any ice or snow inside the living cabin. Of course, you have no view…
Hey you! Person reading this! Looks like you were mounting some hard drives and realized they didn't give you enough of those silly rubber things to mount the drives in the tray! You have screws but… if you put the drive in the board…
Springy feet to help isolate the Beermkr from the table. It helps remove the drumming effect of the table but I also have a lot of noise from the plastic housing chattering. You can adjust the number of walls and infill to get different…
I wanted to isolate my CR-6 SE printer from the desk on which it stands, to cut down on noise and to reduce the risks of printer vibrations impacting prints. I have been very happy with the results of putting my Ender-3 up on squash ball…
Inspired by one of Stefan @CNCKitchen's videos about vibration isolation for his Prusa and the contest this week for using magnets, I thought it would be fun to explore the idea of using magnetically-stiffened flexure feet for my Prusas…
Isolation mount for HY-GAIN DISCOVERER 7-1 40-Meter 1-Element Dipole Antenna ORDER NO. 371S hello here is a realization printed in 3 d for a friend. A hairpin line isolation mount for a 40 meter 1-element HY-GAIN dipole antenna. model 1…
The model is 4cm wide but can be rescaled to suit. Rescaled to 3cm for the Nvidia Shield (3 spikes facing the device) and works great. You could also try it for network switches. Infill @ 40%
Designed these for a makeshift turntable isolation platform (using IKEA Lämplig cutting board). The feet house cut-in-half squashballs. There's .5mm clearance in the XY-direction, so dimensional accuracy of your printer shouldn't be of…
For my Studiobricks cabin i needed some hooks . Thes slide just into the slots of the foam-sheets. for the strapholder and headsetholder i insertet a peace of neoprene (any material will do) into the upper square hole, so it holds better…
Update: included TPU feet from Elan As part of my Lack Enclosure Build for my new MK3S+, I wanted to isolate printer vibration from the table top and reduce noise. I designed my own feet which included outboard supports on the front of…
Isolation Board Game! At the time I couldn't find any printable versions I liked so I made my own. The fitment test object is so you can test the fitment of tiles and pawns without having to print the entire board. You need 2 pawns and 46…
I felt that the ender 5 s1 would benefit from some vibration isolating pads. so I made these, and they simply just go under the factory feet. I have no way of testing but I feel they do help with reducing vibration. I printed with tpu…
This is a vibration damping mount for a Vive Tracker to be used with motion compensation software. EDIT: This absolutely will not dampen my D-Box haptics on the race track over a rumble strip or in Rally. It might be suitable for MSFS and…
Description: A direct replacement for the Sony PVM-14L5 rubber isolation feet. This will also fit other PVMs such as the 20M4U and 1954Q. Printing: Foot: Use FlashForge ASA or equivalent alternate. 0.4mm Nozzle, 0.2mm height, 50%+ infill,…
Use a 4mm bolt and a t-nut to install. The base, pad, and cup slide together. The pad I used can be found on Amazon: https://www.amazon.com/gp/product/B009M9627U
I liked Forker45s take on vibration isolation feet but didn't want to wait for the bought isolation pads so I made some quick ones printed in TPU. Printed at 10% infill and 3 perimeters for flexibility - you don't want a rigid object for…
Mine was vibrating a lot through the floor. Print in a soft and flexible filament --- I used 85A TPU. You will need to mirror one across the X-axis when printing for both sides! I ended up flipping it upside down also (i.e., print with…
Thanks for looking at my first model. I used an 12mm long M3 socket head hex screw and a t-nut. I spaced it far enough away so I didn't have to remove the rubber feet on my SV06 Plus. I have included the step file if you need to modify…
Just simple modification of existing hook for use for more items (in this case isolation tapes).
