123 modeli
Rancher 4×4 – 3d printable set of parts for your 3d printer. Model is approx. 53 cm long (1:8 scale) and is prepared for your RC equipment. You can buy this model on www.3dsets.com What you get: 3d printing files: .stl and .gcode…
What more could you want than 50 slimes in your home
You have option!! Four option on the pintle hitch alone Pintle hitch . Connects with 3mm eye bolt. Works better and cost less. https://amzn.to/3W2ogoN (US Amazon Affiliate link) Strongest Pintle- Uses a 3mm Eye Bolt cut to to allow the…
Stand for 3Dsets Jeep Rancher 4x4 & Landy 4x4 & Bamboo 10/2/2020 - addes v2 upper part for much more stability 13/2/2020 - added v2 middle and bottom part, can now be screwed together 2/10/2023 - adde middle R-20 part for compatibility…
Angry eyes for Rancher jeep from 3dsets.com To be glued on top of the default grill Print instructions No tested yet, let me know how it prints and fits
Modified front panel so that the angry eyes grill fits over it. Both parts easy to print flat on the printer. Made holes to replace the two upper 3 x 10 mm screws with 3 x 12 mm screws to secure together the angry eyes mask, front panel…
Just to clarify - this model contains changed files only (based on Model 6 v 1.1.2), to build the whole thing you need other parts from one of the Rancher models from 3DSets:…
This is open differential for Jeep Rancher from 3dsets. I test it on version Wagon, but should be possible to mount it also on other versions. I created it this open diferencial, because I'm using my Rancher in house on vinyl floor and…
These parts allow you to mount standard 12mm hex wheels to your 3D Sets Rancher. The parts include a 12mm sleeve and a 12mm diameter washer to keep the 3mm screw centered. Don't know what this is? Check out the fully 3D printable 4WD RC…
Slime statue flowerpot I made for my bonsai tree. I printed this one scaled to 120 %. Supports are recommended for the top part of the mouth (organic supports worked best for me). The plort should hold inside without glue. I printed mine…
I found some files for the jeep rancher angry eyes but they were separate and required super gluing or screwing on. I had issues printing these and getting it to look clean due to supports being needed so I combined the two models and…
First, a slight apology, I am missing my files from the centre of the vacpack. You will have to model these yourself. To be honest, they would have to be varied depending on the motor you have, and the gearing that works for you. Also,…
This file is a more rigid servo arm for the Rancher. The Rancher itself is NOT part of this assembly! If you want to print the Rancher, you will need files from third party as well. Files can be found at 3dsets.com. The Rancher has 4x4…
I wanted the same bumpers as my Jeep Wrangler, so I re-diesigned the originals from 3DSets. I also customized the winch, winch hawse, a stronger winch drum and the D-Rings. Printed with Overture Matte PLA with 80% infill and 0,10 layer.…
!!!!! Please read before building. This is a metal geared axle and transmission conversion for the popular 3Dsets Landy, Rancher and Bamboo. Axle ratios are 3:1 to 4:1 the original 3Dsets axles are only 1.8:1. The axles and transmission…
Na fixaci dílu používám trochu lepidla, ale není to nutné.
GT2 Belt Gearbox for Landy/Rancher/Bamboo 3DSets models. Use it with my Metal transmission, gears and axles mod This gearbox has a ratio of 4:1. Paired with the AR44 33/8T gears, it is the same overall ratio as original 3DSets model. You…
One of five slimes that I made a little after Christmas. Supports? No supports are required
One of five slimes that I made a little after Christmas. Supports? No supports required
Model is designed from scratch, based on Tube Doorsteps for Model 1 & 2 Required screws for assembly: 8x M3x10 2x M3x8 (rear screws) Intended to look good with accessory Tube Fender Flares for Model 1, 2, 6 , but it will fit with the…
Modular segmented back light for Rancher from www.3Dsets.com
The simple design can be printed on a 0.4 mm nozzle. The detailed design needs to be printed with a 0.25 mm nozzle. I made them to fit a standard poker chip tray.
This model set includes a two part mold that can be clamped together as well as a single part, fully enclosed mold. Both options allow you to pour in your medium of choice from the top to end up with a nice flat bottom and smooth top. If…
FRONT LIGHTS: I used silver filament for the light and black for the shape. Transparent filament for the turn signals. Then I cutted 2 circular shapes from the plexiglass used for the glasses of the model. BACK LIGHTS: I used black…
I made this as part of a trio of slimes (the other two being the puddle and quicksilver slime). Supports? You shouldn't need supports, but if you print large enough, your slicer program might add supports under the eyes. I didn't have a…
One of five slimes that I made a little after Christmas. Supports? The only part that should need support is the sphere
A model based on the game slime rancher I had created on a 3d printer then painted with Mont Marto brand acrylic paint. Model made in blender.
My tire kept slipping on my rim with my Rancher wheels and Super Swamper tires. These rings help you "lock" the tire in place. There is also an option to use M3 nuts as weights — 48 per lock ring. Enjoy and post your makes! If you found…
3Dsets Jeep Rancher 4x4 Light with hole for 5mm led Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15 Infill: 25% Filament: Inland PLA Black/White Category: R/C Vehicles
This is a remake of a previous model I made that got ruined during printing. Most of the work went towards making the model more compatible with printing, although the ears and side stripes were redone completely. Supports? Like the Tabby…
I made this as part of a trio of slimes (the other two being the fire and puddle slime). Supports? You shouldn't need supports in any place besides the long horn things, but if you print large enough, your slicer program might add…
I made this as part of a trio of slimes (the other two being the fire and quicksilver slime). Supports? You shouldn't need supports, but if you print large enough, your slicer program might add supports under the eyes. I didn't have a…
Work in progress changed to READY TO MAKE! - 5.11.2020 Print, assemble, ENJOY Share your feelings down bellow in comments :) If you like it, you can support me with cup of coffee…
Switch for motor regulator of Rancher from 3dsets.
Ich habe für mein 3DSets Model 6 ein paar neue Türen entworfen. Die Fronttüren davon sollten auch bei Model 1 & 2 funktionieren. Damit der Spiegel besser passt habe ich auch die Original Spiegelhalterung angepasst.
This is a side grille for Model 6 Rancher from 3DSets . Use 4 Screws M2x8 and screw it into the side panel.
Ich habe mir für meinen 3DSets Model 6: Rancher 4×4 Wagon die Haube etwas angepasst. Die Haube hat Einlagen für die Lüftungsgitter. Für eigene Anpassungen habe ich STEP Dateien beigefügt.
It's a remix of https://www.thingiverse.com/thing:2610462 but I was unable to mark it as a remix. For supports I've used tree supports in Cura slicer and 0.16mm layer height Print Settings Printer: Ender 3 V2 Rafts: Doesn't Matter…
I wanted to add some more details to my model, so here's what you'll find: -Hood Flap: This is the hardest part to print, I failed a lot of prints before make it. Print it slow with raft and support, 100%infill and 0,1 layer. In the…
Everyone's Favorite Bovine Kubernetes mascot comes to 3d-printing. I have attached the right-horn to the main cow body for easy printing.
I re-designed those tube side protections to make them look the same as my real Jeep Wrangler. In the pictures you can see the right orientation for printing. Use raft anf tree supports. I used Overture Black Matte PLA 0,1 layer and 50%…
I made this stand loosely based on the one made by xBenny (https://www.thingiverse.com/thing:4139282) for the original Rancher. But since the Wagon version has the center of gravity further back I felt I needed something different. There…
Recently finished my 3DSets Rancher Hardtop, and my wife fell in love with it. She took a look inside the interior, and was surprised to see how detailed it was, especially with the fact that it had cup holders. Jokingly, she said, “You…
One of five slimes that I made a little after Christmas. Supports? No supports are required
Some tweaking for the rim on add slot to have more grip inside the tire and make it bigger than the original for about 3mm so can get more tight i use the 1.9/107mm inch tires Hope this help Big Thanks for the 3d sets
Third working brake light for the 3DSets Jeep Rancher RC, using 5 micro LEDs from Aliexpress https://it.aliexpress.com/item/1005005930441321.html?spm=a2g0o.order_detail.order_detail_item.3.2122582fN0Fgup&gatewayAdapt=glo2ita The third…
4-Link Suspension Kit for Rancher 4x4 or other models with similar suspension. This is a “Bolt-On” kit that requires no reprinting of most of the existing parts Just the Center Chassis Mount. All parts bolt onto existing holes or…
Stand for 3Dsets Jeep Rancher Wagon 4x4. Category: Vehicles
I wanted to re-design the rims of my Rancher RC model to make them look the same as the rims of my Jeep Wrangler. I've also added the brake disks. Printed with Overture Matte PLA 100% infill, 0,10 layer and ironing enabled.
CZ: Úprava dílů pro vozidlo 3DSets Model 2 Rancher 4x4. Zaměřeno především na těžký terén pro expediční vyjížďky. Původní model: https://3dsets.com/product/model-2-rancher-4x4-hardtop/ Rozšířené osy o 10mm na každé straně a zesílené +…
Supports? None should be needed. I wanted to wait until I had four other red slimes to post this, but I thought I might as well since I have it done. I'm thinking of and making other models besides slime rancher, but here's the rest of…
Supports? None should be needed This is one of six slimes I made over a break.
Supports? None should be needed This is one of six slimes I made over a break.
I make a little bit upgrade of the repro in Rancher from 3dsets
Adaptateur avec taraudage pour piscine tubulaire habitat et jardin pour pouvoir brancher un aspirateur ou robot hydraulique sur la prise aspiration de la pompe…
I modified taillight for Rancher to use the lights from Aliexpress. There is main (5mm), brake (5mm), return (5mm) and turn (3mm) light. https://www.aliexpress.com/item/1005002257228043.html?spm=a2g0o.9042311.0.0.27424c4d4OeVGu
Non printed parts: 2x M3 nut and screw
BBS rims for 3d sets rancher. maybe they are suitable for other models too tested and durable you will need 5x classic m2 screw
Inner ring for type A wheel for fixed tire position. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.24 Infill: 15 Filament: DevilDesign PLA Category: R/C Vehicles
End yokes designed for Traxxas Driveshafts. On rear end is not necessary trim length. Tront cardan bust be cutted for proper length. Original Traxxas part: TRA5451X. Printed from Prusament PC-BLEND
You'll need some glue and patience to assemble the model togheter. The model is about 13cm long and 6cm wide. Printed it on a ender 3 but with the current printer it can probably look better than the photo I provided. Made this on onshape…
I printed with supports. Slide the switch into the holder, it is easier than to press it in. To remove slightly lift the end of the switch with pliers.
Nezbytné podpěry pod středem kola. Suitable for drifting, ideal for fun on ice. You can find other types of wheels and other models on my profile: https://www.printables.com/cs/@VojtechStraka_466782/models
This is not a finished project and it has nuances such as assembly difficulties. I will not be finalizing it, so I am posting the .step and .f3d files for your modifications. You can modify this to use a glass vase or cup, but I wanted to…
This is a stand I designed from the Rancher's “centre of the chassis” STL file using Fusion 360. It negates the volume occupied by that STL to ensure a solid fit. This should be a trivial print, as there are no supports required, no fancy…
Roll bar to go with the roll bar offered for the Model 1 from 3dsets you still need to purchase the roll bar addon from 3dsets if you havent yet
This is a modified bumper for the 3dsets Model 1 Rancher 4x4 - https://3dsets.com/product/rancher-4x4/ It is designed to fit a Caddx Ant analog camera - https://caddxfpv.com/products/caddx-ant-analog-camera Wiring routing is similar to…
Necessary supports under the center of the wheel. Suitable for drifting, ideal for fun on ice. You can find other types of wheels and other models on my profile: https://www.printables.com/cs/@VojtechStraka_466782/models
non printed parts needed: Optical PMMA LED Lens Reflector on Ali (i recommend 60 degree) 1W/3W High power LED 20mm star pcb on Ali (1W is sufficient, I recommend warm white for older cars, looks much better) front parts of the fenders…
原版电机为4孔螺丝固定，DUALSKY 3530为5孔比同规格电机略短一些。后面固定坐也不匹配。 我修改了原文件中的[Pulley 1 - Motor - B] [Motor Mount]这两个，直接替换掉即可使用。
This part is a needed for Rancher 4x4 as the holes in the original end has different dimensions. The Bumper parts can be download there under this link…
This model does not need any supports.
I wanted to safely stretch wires from tail LED light to receiver/lights unit. This conduit is placed at the bottom side of the wheel house and connects the side where tail light is installed with interior of the car. The only tricky part…
Este modelo representa la icónica Slimepedia del juego Slime Rancher, rediseñada por Torres3D como figura coleccionable de 8 piezas. ✅ Fácil de imprimir ✅ Piezas optimizadas para FDM ✅ Ideal para pintado, decoración o diorama geek 🔽…
Référence d'origine: YF1291633
I modified the front wheel houses to accommodate space so that I can fit Injora headlights without having to cut into the plastic. The Injora Headlight mod can be found here:…
Rancher Government Carbide Logo for printing.
Includes: Rancher Longhorn Harvester Fleet
RGS logo for placement in our offices. 250x250x5. Printed on a Voron 2.4 coreXY but could be downsized for the printer of your choosing.
A woggle of Gaboo, the classic monster from Monster Rancher! An easy, single-color print that looks great in glow-in-the
Modified hardtop front frame to make it compatible with https://www.printables.com/model/116619-roof-holder-rancher.
Rancher Government Solutions Logo with broken out letters
a bookmark for a book in the form of a honey slime from the game Slime Rancher
a bookmark for a book in the form of a honey slime from the game Slime Rancher
FRONT LIGHTS: I used silver filament for the light and black for the shape. Transparent filament for the turn signals. Then I cutted 2 circular shapes from the plexiglass used for the glasses of the model. BACK LIGHTS: I used black…
This is a remake of one of my earliest models I've ever made. I'm happy with the improvements I've made (except the eyes, those just look a bit odd). Supports? The only area you should need supports is the side stripes area. However, it…
One of five slimes that I made a little after Christmas. Supports? Supports are need a few places for the tail.
Roof holder for the front part of roof in Rancher from 3dsets. Use 4 screws M2x10 to the roof and 4 screws M2x6 which you take from the tube roof of Expedition set. If you want to use this holder you have to cut the sun shades to the half.
this cozy little home can be a great decoration for a train layout, or get you a 100% In a housing design class Print specifications: windows I used translucent PLA for the window part of the window color swap/mmu/ams/ace/paint reqired…
Supports? None should be needed This is one of six slimes I made over a break.
Supports? No supports are needed This is one of six slimes I made over a break.
Supports? Supports are needed for the ring. Also, be careful with the ring; the ring is thin are could break if you're not careful. This is one of six slimes I made over a break.
This is my version of the holder for QuicRun 16BL30 ESC switch. The 0 and 1 indicators are printed in white. Two 2x14 screws are required, installation is a bit tricky, because the screws holds the whole thing together.
Modified servo arm with ball joint for Rancher. Requires to have servo on axle modification installed on the Rancher. Shortened Drag Link is required (not included) - please see attached image. Requires M3x20 screw. Not tested in…
Bare in mind that im using different bumper from 3Dsets Extreme pack .
This is one piece mount and Rotopax cans, use MMU/AMS to multilor it. Cup can be found in original model.
Bring a piece of the Far, Far Range into the real world with this detailed Slimepedia from Slime Rancher 2! This 3D printable model is perfect for fans of the game who want a fun collectible, prop, or display piece for their gaming shelf.…
you need longer screws and self locking nuts (yes, shocks are now screwed into self locking nut)
