Liczymy pasujące modele…
These keys can be inserted in the lock hole and help you identify the drives, as well as twist to unlock Print the pegs separately, then add a drip of superglue and insert into the key, if it does not fit simply sand the edges a little.…
Since I keep my hardware in an IKEA Kallax shelf behind a door it get's quite warm in summer. To not damage the hardware I designed a heat tunnel / heat pipe for any 80mm fan that can be just glued into the top right corner. The fan will…
Damping foot for Synology DiskStation to isolate the HDD sounds from the rest of my house
Fit tested on DS720+. Key sticks to the side of my rack where it wont get lost.
Fits various models, like DS211+ and DS218+. Replaces original cover. Mash filter required to be glued from inside for air pass and filtration.
Inspired by: https://www.printables.com/model/969418-synology-ds-1522-anti-vibration-stand
A very quick and very basic desing that it works for hanging the key for the HDD bays. It uses one of the screws from any back fan. Category: Electronics
My main goal is reliability. It's a very robust design but on the other hand it takes a long time to print There are two holes for 6mm screws. The shelf is ventilated from below so as not to disrupt air flow. Please see the plan with…
Replacement HDD tray lock for my DS916+. 3 of thous were broken after bad packaging during shipping. Fits for DS211+ and possibly other similar models too.
Wanted to try using a TPU stand base instead of the foam rubber strips. Only made it 2mm thick. Might try thicker later but going to give this a try for now. You're free to go thicker in your slicer. 15% infill sounds about right. 2-3…
A cradle designed to hold the 100W power adapter for certain Synology DiskStation NAS units. Specifically, the model “Adapter 100W_2” AKA “Adapter 100W Level VI” (Dimensions 13.7 x5.9 x3.5 cm, currently used by NAS models DS920+, DS918+,…
This model is inspired by Synology DS 1522+ Anti Vibration Stand by reserve and Synology DS923 antivibration stand by Adam Nuclear , but made from scratch in OpenSCAD using BOSL2 library to fit DS920+ specifically. Using this stand has…
Ermöglicht die Montage des Synology RT6600ax an der Wand - der Adapter sorgt dafür daß der Router flach an der Wand anliegt.
Remix of kai's HardDriveHolder D7, which didn't fit in my DS1815+. It is not that pretty, well, it was, as it came from kai, perhaps I will do some further improvements. But in this state it will work just fine. Appreciate to get some…
A 3D print model for a Synology drive bay key provides an affordable and practical solution for replacing or duplicating the small, often misplaced keys used to secure Synology NAS drive bays. Designed with precision to fit Synology lock…
I modified this model to fit Synology D8 (1813+ etc) drive bays. I initially printed the original model thinking it would fit but it didn't, one exacto knife cut later and it fits! so I quickly modified it in Prusaslicer and boom! new…
These keys can be inserted in the lock hole and help you identify the drives, as well as twist to unlock Print the pegs separately, then add a drip of superglue and insert into the key, if it does not fit simply sand the edges a little.…
Da mein NAS unter meinem Schreibtisch montiert ist und mein Sohn gerne Knöpfe drückt (vor allem leuchtende), habe ich diese Abdeckung entworfen, damit er es nicht ständig ausschaltet. English: Since my NAS is mounted under my desk and my…
Wallmount for Synology NAS. Level, four screws, put on top. Done. Best for SSD NAS I guess the classic drives can rattle. You may need to isolate.
This was designed to house my Synology DS 418 at the bottom of my RackMate T1. It may be possible to install this solution at other positions but this was not my intent. Same goes for other models of Synology NAS units. In my case…
A simple shelf and plate for the Synology DS215j NAS to fit into a 10" Mini Rack. The size of the opening for the NAS is 101mm x 161mm - this may work for other similar sized NAS units but no guarantees. Smaller printers like the Ender 3…
Replacement Part for the DiskStation 212j model. You need a blue 5mm LED and a 6x6x8mm pushbutton. Soldering skills needed, as you need to disassemble the 212j LED Board, remove the old button and solder wires from the button and the LED…
A Simple Holder for DS218 and DS218+, DS220+, and DS214Play. DS216+II Print Settings Printer: A30 Rafts: No Supports: No Resolution: 0,22mm Infill: 25% Filament: Janbex PLA RED Post-Printing Mount it to the Wall I recomend to use Screws…
The Synology WRX560 wireless router/access point doesn't have any holes or come with any wall-mounting hardware. This model offers a solution by providing a wall-mountable platform with clips that hold the router securely. Requires…
Remix of kai's HardDriveHolder D7 Applied Models: DS211+, DS212, DS212+, DS213, DS213+, DS214, DS214play, DS216, DS216+, DS216+II, DS412+, DS413, DS414, DS415play, DS415+, DS416, DS416play and DS916+
I have always disliked the appearance of my Synology NAS in my 42U rack due to the large gaps on the left and right sides of the system. So, using the power of 3D printing, I present to you 6U rack blanks designed to make your Synology…
Ein Unterbau für das NAS DS218+. Seine Innenabmessungen betragen 85 mm x 187 mm x 25 mm (B x L x H). Die vier Füße des NAS passen genau hinein. An der Vorderseite befinden sich Schlitze zur Luftzirkulation, an der Unterseite vier…
Since I keep my hardware in an IKEA Kallax shelf behind a door it get's quite warm in summer. To not damage the hardware I designed a heat tunnel / heat pipe for any 80mm fan that can be just glued into the top right corner. The fan will…
A shelf just big enough for a Synology mesh router, model MR2200ac, from which the router can't be removed unless the shelf is first removed from the wall. This ensures that the router can't fall off. Here's how it's done: Print the…
Sleve to convert a standard (longer) esata cable into a screw locked cable for Synology NAS extensions like DS715. I used a Roline cable with the plug dimensions of 14.5*8.2*21mm. Use the FreeCAD Model to change it to the dimensions of…
When I pulled apart for cleaning my 6-year-old Synology DS216 NAS I found it had broken (disintegrated) the 10mm diameter rubber retention rings that hold the cooling fan in place. Design is for a replacement using Flex filament (TPU 95).…
This part is to replace the lock/latch on the Synology drive caddy/tray. This piece is recommended for Resin printing, but FDM can work well. This part is very tiny (~15mm in length) - Excellent bed adhesion is REQUIRED. Note: The added…
Project data: https://github.com/MarioHP/Synology-Display-UPS-Monitor
I designed this front plate to house my Synology DS 920+ at the bottom of my RackMate T1. Included Keystone and non-Keystone versions. After a few failed prototypes (RIP my filament), I finally got the measurements right. The DS920 is…
Replacement drive rail for the Synology D6 drive trays. Not sure how I lost mine, but I have them missing from 2 of my trays. I printed in ABS, although I don't think heat/warping will really be a problem, but I'd rather be safe.
This is a filter for the front of a Synology DS 920+ NAS and probably other 4 bay models from Synology. It keeps dust, spiders and insects out of your device. The opening is big enough to keep access to the disks and there is plenty of…
Simple Model of a foot to raise the Synology DS9xx NAS. I used TPU and Archimedean Chords Infill Pattern.
Skadis Mount Brackets for Synology DS223 NAS Remix of the wall mount from @Hemi345 and the skadis supports from Ryan Plourde These brackets can be used with any Synology DiskStation 2-bay Plus, Value, or J-series NAS: DS218, DS223j,…
Synology DS220J Wall Mount brackets to mount the NAS to the wall. Please be aware there is only one rotation for mounting as it has one filleted side and one chamfered side.
Redrew the original from @UnluckyForSo_3537297 and modified it to better fit custom racks and Synology on a rack shelf. Redrew the original and modified it to better fit custom racks and Synology on a rack shelf. Having the NAS on a shelf…
Mounting bracket to hang the power adapter from a Synology DS225+ NAS on a wall. I forgot to make the slot for the cable on one of the pictures, i just used a saw to cut this after printing and added the slot to the model before…
Sliced from Fusion360 to Prusa Mini directly, works well in PLA with default settings.
The model created by @Niggich unfortunately did not fit for the power supply of the DS918+. So I created a new model, inspired by his design. The pocket now measures 59mm x 35mm . It might fit for other Synology NAS models as well as…
These are 3D-printed anti-slip retainer clips designed to prevent a Synology DS923+ from sliding inside a DeskPi Rackmate T1 mini rack. The clips act as mechanical stops at the front and rear of the NAS, keeping it securely positioned…
Damping foot for Synology DiskStation to isolate the HDD sounds from the rest of my house
Fit tested on DS720+. Key sticks to the side of my rack where it wont get lost.
Подставка, для постановки ds1515+ на бокс отверстиями для вентиляции
Tento model je dodatečný držák pro Synology DS215j, navržený pro moderní pevné disky, které postrádají středový otvor pro šroubek. Doporučení pro tisk: Materiál: PETG Výplň: 70 % Gyroid ============ This model is an additional bracket for…
Fits various models, like DS211+ and DS218+. Replaces original cover. Mash filter required to be glued from inside for air pass and filtration.
I made this mounting block for the Synology TC500 camera as an adapter between a standard articulating arm mount and the manufacturer base for the camera. This model is, for all intents and purposes, a slightly beveled cylinder, printed…
A wall mount for the Synology DS118, so you can hang it on your wall.
Titled: Spaceman. Pictured printed on Esun Magic PLA Dark Green. For the Visor, I used a plastic mesh screen that I painted gold. It is then held in place by the retainer part that can be glued on. For the Rubber Mounts, I printed these…
This is a replacement design for the Synology DS2XX+ Series Faceplates. The Rubber Mounts attach to the Faceplate and I recommend printing these with TPU. They can be covered by the cap piece, that is also included. I also recommend…
Wall Mount for Synology NAS (DS & DX Series) This wall mount is designed for Synology NAS units from the DS and DX series , with a maximum device depth of 265 mm . The design uses four mounting screws on each side to securely hold the NAS…
I wanted some larger key/numberplates because the originals that these were based on were a bit difficult to get a grip on. Source Fusion 360 file included. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No…
Replacement Parts for my Synology NAS DS414. Applied Models: DS211+, DS212, DS212+, DS213, DS213+, DS214, DS214play, DS216, DS216+, DS216+II, DS412+, DS413, DS414, DS415play, DS415+, DS416, DS416play and DS916+ Category: Computer
This is a small SSD mounting adapter for my Synology DS218+. Theoretically this should also work for other "slot"-type drive cages. Note that the latch is missing the little pin on the front. Original source for the adapter plate:…
Lovely router by all reports (I haven't actually set it up yet), but the steep angled legs make the built-in mounting slots rather ridiculous. They're an inch away from the wall and tilted at about a 26-degree angle. CAUTION: Synology's…
Made this mod for my Synology DS920+, which is placed inside a bookshelf. The vibrations from the HDDs resonated into the wall and made a lot of noise. After attaching squash balls to it, the vibrations inside the shelf plate is greatly…
WARNING: This model is intended to be printed with modifier meshes to allow for airflow. The original M.2 slot covers do not allow the use of M.2 heatsinks, as they collide with the clips. This redesign used a slightly different machanism…
This is a podest for a Synology NAS to provide some extra space underneath the device. It also comes with a drawer. The drawer handle can be mounted with all kind of screws thicker than 3mm. I used an 5mmx40mm screw to fix it. Files…
I wanted my router to be installed on the outer side of my servercabinet, screws are therefore not possible. Therefore I created a very simple but 100% fit wallmount for Synology RT6600ax Router. Entire size is designed to fit exactly one…
Pour accrocher un routeur WiFi Synology MR2200ac au mur. La ventilation par le bas et le passage des câbles restent assurés. Des ergots empêchent le routeur de basculer. Ces ergots permettent d'accrocher le MR2200ac au plafond s'il est…
I lost my original keys (found them eventually) so I found a few 3D printable ones, but I didn't really like them, They were nice and functional, but I wanted more of a standard key looking one that could sit on a keychain. There are 3…
Hard Drive Tray Compatible with the Synology line of NAS' that use the D5 Tray. Does not have 2.5" mount holes.
2.5" inch HDD/SSD holder for Synology DiskStation NAS It is suitable for both 7mm and 9.5mm height disks Equivalent to Synology Disk Holder (Type C) I have made it for my DS118, but in theory it should be also suitable for the following…
Synology only lets you lock the drive bays, but not the buttons. You can turn of the led lights, but if you child is very persistent, it will find the button anyway. I created a cap that hooks to the usb port of the NAS that sits on top…
Not locking. Does not fit 3.5-inch drives. Requires 4 M3x5 countersink screws to mount.
Vibration dampening support to be placed under the NAS's square foot. May fit any model that uses the same 13 mm side foot. To be printed in TPU - for my usage, with only one “heavy” 3.5" hdd installed printing it with two walls, 0.2 mm…
Important notice: First thing is first:) This design is free for the benefit of the community, but If you like my designs and want to contribute, you can make a donation to buymeacoffee or paypal, that will be greatly appreciated. I know…
to be screwed with the case screw under the power connector
Designed a strong wall mount for Synology Diskstations with two drives. I wanted the Diskstations to be easily removed from the mount, so I added a gap in the wall mount where the feet of the disk station fall into. The model consists of…
Two easy-to-print hooks for adding an additional drive - WD Passport - to your Synology DS218 server. Add adhesive felt pads and everything will sit tight.
Update. V3 is now printed on the back with a support slicer on the bottom for better support on the NAS. So for many years now I have enjoyed using Synologys NAS server solutions. Ive been through different models, and for the past 10…
My Synology NAS was making too much noise from vibrations so I remixed a Bambu Lab vibration dampening foot to work with the large Synologies. I printed in 95a TPU, but PETG could be a viable alternative as well if printed without the…
My first model, simple and overkill, but effective. Takes about 1.5 hours to print, print two for both ends. Print in TPU without supports, with the following parameters: Material: CR-PLA_1.75 Layer Height: 0.15mm Wall Line Count: 3 Top…
Designed to rackmount a Synology Rackstation Ideally print in PETG or better PLA would warp under heat in cabinet
German: Ein kleiner schnell gedruckter Schlüssel, um die Festplatten der Synology NAS Boxen absperren zu können. ========================================================= English: A small, quickly printed key to lock the hard drives of…
These are replacement keys for Synology NAS like DS918 or any other with 3,5" Hard disks with a Key lock. I use this in my private environment because there is no extra safety needed (These locks aren't safe anyway). It's also nice to…
Keep your NAS power plug secure by using the Kensington Security Slot! Specs ✅ Synology DS220j compatible Print tips 🧩 1 part ⮑ Print original orientation from the STL ✨ Support free! 🏋️ 15% infill 3 perimeters can help with strength PETG…
Changes 1. Removed the fan relief to mount different fans. 2. Added Filter hold to mount air filter mates.
These brackets can be used with any of the Synology DiskStation 2 bay Plus, Value, or J series NAS: DS218, DS223j, DS223, DS224+, etc. Space the brackets 140mm apart and the flange will trap the Synology's feet preventing it from sliding…
This is a Synology DS218/DS220/DS224+ Stand to reduce noise and vibration. It also helps with better ventilation. You need door seal stripes at the bottom of the stand with a 9mm width. I used these:…
Made for the Synology DS1522+ Disk Station. Things you need: 4x Squash balls, 40mm diameter (2 yellow dots) 4x ISO 10642 M3 x 10 mm Screw 4x DIN 934 M3 Hexagon Nuts
This is a heavy duty wall mount for a Synology RT2600ac router. I used #8x1/2" screws to attach the router and #10x1-1/4" screws to attach the mount to the wall. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No…
Synology TC500 Flat Mount for use with zip ties as temporary or permanent attachment.
