25 models
Gauge for laying parallel tracks at the standard spacing for open line and station. It rests on the rails, two tongues centre it. Please note: nothing of this design has been printed yet, and it has not been tested on a layout. The…
Euro pallets as loads for loading roads, goods sheds and flat wagons: single, stacked and in three sizes. Footprints from the standard. Please note: nothing of this design has been printed yet, and it has not been tested on a layout. The…
Blank panel for empty rack units: 1U or 2U, closed or with vent slots. Centre part plus ears for 10″ and 19″ racks, no supports. Fits: Empty rack units (1U or 2U) in 10″ racks (hole spacing 234.0–239.5 mm, slotted) and 19″ racks (EIA-310,…
Free check gauge for each scale: clearance for platforms, portals and signals, plus a window with the vehicle envelope. Dimensions from the current NEM editions. Before you print a portal, a platform or a load, this gauge shows how much…
Sticks onto the dashboard with VHB and holds a 52 mm gauge facing the driver. Tilt 60, 75 or 90°, no drilling. The pod sticks on top of the dashboard on the driver's side and holds a 52 mm gauge facing the driver. 60 mm gauges fit the “60…
Single adapters from round bases to square bases: pocket Ø nominal + 0.4 mm, outside target − 0.2 mm, 3.0 mm high. Only the pairs where the wall is thick enough. Fits: common 28–32 mm tabletop systems, made by base size (nominal sizes of…
Nine stick-on clips in three sizes to route the wiring of add-on gauges neatly behind trim and under the dashboard. When fitting an add-on gauge, the wiring is often the untidy part. This set of nine stick-on clips routes it neatly along…
Three test rings for 52 mm or 60 mm gauges, a single-DIN sample and an M3 test block. Know after about 1.5 hours of printing whether printer and material fit. Before you spend hours printing a pod or panel: this set shows after about 1.5…
Drops into the cupholder and holds a 52 mm gauge tilted 45° toward the driver. No drilling, fits Ø 70–85 mm cupholders. The pod drops into the cupholder and holds a 52 mm gauge , tilted 45° toward the driver . 60 mm gauges fit the “60 mm”…
Free, print it first: combs for round, square and rectangular bases in five clearance stages, a height ladder, a socket hole bar with a rod sample and a real 5 × 25 mm row. Fits: common 28–32 mm tabletop systems, made by base size…
Cable manager for one rack unit: five open hooks you drop patch cables into from above, plus four pass-throughs to the back. Ears for 10″ and 19″, no supports. Fits: Patch and data cables (not mains cables) in 10″ racks (hole spacing…
Closes an empty 52 or 60 mm gauge hole, e.g. in a two-gauge panel while only one gauge is fitted. A blanking cap for empty gauge holes : you have a panel for two or three gauges but only one fitted so far? Or a pod stays empty for a…
Plugs into a blank slot below the heater controls of a Golf 3 instead of a cap and holds one 52 mm gauge flush. For the VW Golf 3 (also called Golf III or Golf Mk3, type 1H), including GTI, VR6 and Vento : the pod plugs into an accessory…
A real 1U rack ear, a piece of device carrier with the M3 joint and a tolerance comb: check rack and printer before printing the full insert. Fits: 10″ racks (slot for 234.0–239.5 mm hole spacing) and 19″ racks (465.1 ± 1 mm); the same…
Free test part: does your sleeved card fit our card boxes, and how tall are 20 cards? One frame per format, 3–6 g. A small frame with exactly the inner size of our card boxes . Put your sleeved card in: it should sit loosely without…
Free test part for all Eurorack parts: 3U piece with 8 HP and hole pattern, 1U tiles in Intellijel and Pulp Logic format, tolerance comb. Fits: Eurorack 3U (8 HP piece with the Doepfer A-100 hole pattern) and the two common 1U tile…
Measures on your own case what the maker does not publish: corner radius, floor edge, floor cross, rim height and the clearance of our tiles. Fits: Systainer³ M, L and XXL cases and the Sortainer³ drawers; inside dimensions from the…
Hexagonal dice tray, 150 mm across the corners and 25 mm high; several stack into each other. With a recess for a felt or foam insert. No supports. Please note: the tray has not been printed yet. The stacking foot (3 mm, 0.2 mm play) is…
Round bases with a clamping slot for cardboard standees: three board thicknesses, two diameters. The slot narrows towards the bottom and holds the board without glue. Please note: nothing has been printed yet. The clamping slot (0.15 mm…
16 quivers per M tile from Ø 8 to 30 mm; pens, files and brushes stand upright. Fits: Systainer³ M and L cases; inside dimensions from the manufacturer's price list. Not an accessory by TANOS or Festool and not affiliated with them;…
Flat base with a slot for the bottom edge of the front panel: the removed module stands upright on the desk, the back stays free. Fits: Eurorack 3U modules up to 4, 12, 24 or 42 HP (panel dimensions after the Doepfer A-100 construction…
Clips for a single charging cable on the wall: press the cable in and it snaps into place. Four sizes for the usual Type 2 cables, four clips per file, printed in PETG. Fits: Single EV charging cables Ø 10, 13, 17 and 19 mm (cable Ø from…
Small clips that slide into a free keder rail from its open end: 2 hooks, 2 eyelets for the clothes line and 4 clips for a light chain or cable Ø 4–8 mm per set. Three sizes. Fits: Free keder (awning) rails without a keder in them,…
Free test plate for the garage: seven fit rings for the collar of the Type 2 plug, a sample of the tapered seat and a clamp sample for charging cables 10/13/17/19 mm. Fits: Type 2 charging plugs (IEC 62196-2) and charging cables Ø 10–19…
Free fit test for the camper: three short edge clamps show on your own furniture board which size sits; four keder test strips show which head and neck fit your keder rail. Fits: Furniture boards 11–20 mm thick and free keder rails in…
These are all currently available results.
