562 models
iPhone mount for bike handlebar for phones with a case. Easy clip in, no obstruction of the screen, angle is adjustable. The phone is fully usable while in the mount. You will need additionally 4x M3.5 x 16 screws (ISO 7046) 4x M3.5 nuts…
The mounts are designed for handlebars + handlebar tape with a diameter of 40mm and increased ground clearance. I printed whit PETG them with 4 perimeters, 10% honeycomb infill, without top and bottom layers.
I remixed these from topxnbo on thingiverse to be the same thickness for the bar as the depth guides. I also added an easy angle gauge to each bar. 1/8" - 90° angle gauge 3/16" - 85° 1/4"- 80° 5/16" - 70° 3/8" - 60° 7/16" - 45° 1/2" - 30°
A GoPro mount for 45mm (1.75-1.77in) rollbars! Made for Blackbird Fabworx GT3 and Hard Dog “Hard Core” MX-5 Miata rollbars. The model has clearance for felt strips (or other non-marring material) around the clamps to help dampen…
Print Settings (Should be in 3mf project file): Material: PETG - PLA will stress fracture over time and PETG hinges more nicely Layer Ht: 0.3 mm Perimeters: 3 Top Solid Layers: 6 - Helps with waviness from the default 4, purely aesthetic…
The honor box was purchased at Michaels Arts & Crafts store. These models are used to hold the bullet casings, U. S. Pin, challenge coins, and military bars. Casings are held in place using a small wire or thread and sit on a “shelf” on…
Had some materials left over from other projects and decided to make the kids a set of monkey bars over their sandbox. I made this part to allow for locking the bars from spinning freely. Metal base flanges cost over $10 locally so beefy…
As well as being unsightly, bird droppings are known to be problematic to high performance memory. Protect against this very real threat by installing bird control spikes on your memory today. 0.15mm or 0.20mm layers will work fine, no…
This model is designed to be used with the Prusa Enclosure, which has a hinged lid. The two bars are screwed directly onto the lid of the Prusa Enclosure. The feet are screwed onto the corners of the dry box where the bottom plate is…
Description Use Case I remixed this GPS support model so that it holds on a Ø12 mm tube. Be careful to take a break during printing to slide the nuts that will be held in place during tightening. Hardware need: 2 Vis CHC M8x25 2 M8 brake…
This is a 15x15x40mm bubble level holder for Vixen-styled dovetail bars. And the hole pattern fits dovetail bars made by MoreBlue. p.s. A slim version V2 is added.
I secured my bags against movement with these tension belt mounts. Tested on a 3 week offroad morocco trip without any issues. The outer diameter of the crashbar is 20,3 mm (0.8 inches). The screws used are M6x20 and a locknut. I…
This is a costume wrench for unscrewing of the cap that keeps on the handle bars on ROG pony. It works but must be printed from good materials because the little pins can break off when you try to screw it down. PLA is not good enough !!!
These press-up v-bars have been used extensively in the gym and at home, for muscle growth, I developed these when there was nothing available out there that suited my needs. Hope everyone enjoys them, please feel free to let me know how…
These are custom cracked-style Dominator Titanium Top Bars designed to fit on drumsticks. I gave them a worn, aged look with subtle crack textures for that raw, used aesthetic. The surface features wave-like detailing and airflow holes…
The zero play guide bar system is a huge benefit for anyone making and using jigs in a climate where conventional wood guide bars will expand and contract. I will use this with my table saw miter slot but you may find it useful with your…
Zero play guide bars for jigs on table saw. I primarily made this for a new cross cut sled but they are applicable to anything. Would recommend using PETG as it is very low friction and won't warp much at all. My process for assembly to…
Set of round bar connectors for rods with diameters between 5mm - 40mm Features: Press-fit of the round bars Countersunk screw locking holes Holes for tensile force absorption Customizer:…
These are printed accessories for adding LED light bars to the Flashforge Adventurer 5 (AD5M) printer. Printing info: Print as oriented No need of supports. The LED “mount” bars were printed on the AD5M. The longer parts have to be…
I have a work light over the printer that casts a shadow of the print head and it was very difficult to see what was happening at the nozzle both in person and with the OctoPrint webcam. It's interesting that most of the existing lighting…
These LED tea light lamps cast exciting shadows on the wall with their 24 pillars and create a cosy and contemplative lighting atmosphere at Christmas. Available in three sizes: Small, Slim and Big All versions are available as a…
UPDATE 07.05.2023: After several requests i added the versions for the most common tube sizes (10, 12 ,15, 16mm) and for 18mm french cleat bar. :-) A French cleat holder for the (crimper)pliers! Inspired by a model by Mikhail on…
For this project I used PETG and TPU. This model is designed for you to split this object according to your bed size. UPDATE: Removed bottom lip x1 and made the feet less of a black hole for glueing by updating Tray x1, Front feet x1 and…
Ride with Style! Decorate your bike with the new FlexiDinos BikeBuddies . Just put two zipties through the holes in the feet and attach them to your handlebar. That's it. I also made a video where I explain it in more detail. I can't…
As said, two versions with and without Gopro mount. The uploaded STLs are designed for an inner spacing between the bars of 75mm and a bar diameter of 22,3mm but those parameters can be fitted to your needs in Fusion. parts for Gopro…
Stretcher bars for embroidery/needlepoint canvas. Use tacks to pin the canvas around the frame like you would with wooden stretcher bars. Use four bars to make a complete frame. Features Stretcher bars from 4" to 10" (in 1" increments)…
I found this great model for a travel soap container, but I wanted the inside to have bars instead of the bumps, so I added them.
Custom Snag Ears for Fox Micron Bite Alarms I designed these custom snag ears for a friend who didn’t have any for his Fox Micron bite alarms. These snugly fit into the rear threaded holes of the alarm body, helping to keep your rod…
This was inspired by a similar concept but is a totally designed from the ground up using OneCNC XR7 software. In searching for a suitable LED lighting solution for my Ender 5, I couldn't come up with just the right combination. So I…
I liked the edits on the featherboard done by r00nee, but the miter bars didn't fit in my Ridgid table saw miter slots, so I edited in order for them to fit. While I was at it, I changed the bottom of the bar to hold either 1/4-20 Hex nut…
Jumping bar fot th Horse Club
Not a terrible lot to say - just some blanks for those of you that want to make your own versions.
Vidlička pro rybářsky prut
remix de https://www.printables.com/model/308219-dremel-drill-press al que he añadido las barras de 22mm
A collection of printable fantasy treasure props , designed to bring your loot drops and dungeon rewards to life. This set includes: Gold bars in various sizes Diamond, Topaz and Gems I designed these myself with D&D-style treasure in…
This is a modular wooden treasure chest. This first set incudes an empty treasure chest, a lid, three coin modules, two gold bar modules and a few spacer elements for adjusting the chest's fill level. (Hint: The spacer elements can easily…
UPDATE: 05/21/2018 Clamp is now located on the left side to be accurate with the actual Hero prop (its on the wrong side on the pictures I took) also added a hole for the metal ring clip. Darth Vader lightsaber from A New Hope - Hero…
Can't forget about my Warrant Officers in the US Army! If using PLA, I recommend resizing the blocks to 98.5% so it can fit snug/tight without using glue. In my opinion, it just looks better to insert it tightly than to glue it in. To…
These are very simple slide-in bars for attaching molle system pouches together. The simplest one just slides in and out and can be removed in a hurry. The other two have small hooks on their lower ends which are relatively simple to…
This is one of around 20+ models I have recently designed for compact push up bars. I am publishing this design because it is sturdy, printable on a small printbed (Prusa Mini) with minimal supports and very compact. I have uploaded…
This model is compatible with the lego system.
Those bars can be used to restock the original bars of the Theo Klein Bosch workbench. I personally like printing them at least with 0.2mm layer height, whereby the top of the bar looks best even in 0.1mm layer height and ironing of the…
I was looking for the perfect filament rack for myself when I came across this excellent design by Jimmit. Very simple but strong and easy to assemble, but I didn't want to use a broom handle so I did a simple remix to fit 1000 x 12 x 1…
To build the mini marimba you need fishing line, two floats, a small spring and superglue. The bars: Use 50% infill for the bars and print them with detailed quality (0.1mm) It's important to let the bars cool down before playing (24h…
Vixen dovetail bars for ZWO Seestar S30 and S50 smart telescopes. I made these in both 60mm and 90mm lengths. The 60mm lengths are good for most of the EQ wedge adapters on the market and the 90mm length is good for the William Optics EQ…
Those edges can be used with the Bosch Theo Klein Workbench / Drilled Bars, see here: https://www.printables.com/de/model/421944-theo-klein-bosch-toy-drilled-bars , to build in 3D :-) I printed them with 0.2mm layer height. PS: Nut and…
I've only uploaded the files I changed, the others can be obtained from Hex2000's post. Note: you may need to change your infill settings to get these to balance just right. It was a bit of trial and error for me.
Thanks to Bwolfey for creating this thing. It works great, but for the purposes of my project, it was a little too long. So I modified it slightly to make this version with the nuts which is about 168 mm. I also modified the nut holes to…
NOTE: If these have helped your crossbar whistles, please leave a make or a comment 💭 and let me know! 🎁 Get $100(s) in Rivian Rewards points and 3 months free RAN charging by using my referral code TODD11893313 when 🛒 ordering a Rivian .…
Based on the print insert included in the G.I. Joe Classified Extensive Enterprises set. Scaled based on a real-world example. Printed in Bambu Silk Gold on my X1C. My .3mf file is attached, as well as an STL
This model is compatible with the lego system.
I printed in 0.03mm DRAFT in PETG without an issue. I recommend using the Gyroid fill pattern, but you do you. I really liked the simplicity of the vertical light bars that Dennis created (https://www.prusaprinters.org/prints/81952), but…
Buttons box for motorcycle/bike handlebars. Diameter of handlebars is 22mm. Holes for smaller buttons is 13mm Hole for bigger button/cradle switch is 20mm You will need: 2x 3mm self tap screws to connect upper clamp with lower box 2x M4…
This is a wooden treasure chest filled with gold bars. Although we created it as an accessory for D&D campaigns and tabletop roleplaying games, it can be scaled and used in all kinds of situations, such as pirate dioramas and board games.…
Samsung Galaxy S23, S24, S25 mount for bike handlebar for phones with a case . Easy clip in, no obstruction of the screen, angle is adjustable. The phone is fully usable while in the mount. You will need additionally 4x M3.5 x 16 screws…
(For smaller illustration models, look here: https://www.printables.com/model/675613-steel-profiles-illustration-models ) All STL files are according to standards shown below. Print info: - All stl's are 100mm in height - Print upright,…
The mount has a default 45 degree angle, but you may alter the play bars position via the slot. There are two versions for printing. The default one with an integrated support line (0.6mm) in the slot for easy printing, and one without…
I made an holder for a garage door remote that fits a 28mm handlebar. I decided to share it because it's for the most common universal 433Mhz garage door remote from Banggood, and I use it since a year now (both the holder and the remote…
My cousin got himself a Traxxas XRT, and wanted more color on the truck so a few minutes in tinkercad, and there are blank, cutout, and labeled side crash/nerf bars for the XRT and X-MAXX(since they use the same bars/frame) I printed it…
This is a remix of the wall mount from @fabiankirchen with a optimized pin mounting system. I recommend to print the main part with the flat (front) side down, 5 wall loops and 50-70 % gyroid infill. No support needed. Please also see the…
Don't forget to like and post your makes, also check out my other egg models! https://www.printables.com/model/734705-beautiful-easter-egg-7-pack-screw-bottom-for-fun-s 0.2mm Layer Height 2 Perimeters 10% Infill 5 top and bottom Brim My…
Prusa core One feet v2 - short
Custom 3D printed spacers designed specifically for Decathlon VAN RYSEL Long Distance triathlon handlebar extensions. These spacers allow precise adjustment of aero bar positioning for improved comfort during long-distance cycling,…
Don't forget to like and post your makes, also check out my other egg models! https://www.printables.com/model/734705-beautiful-easter-egg-7-pack-screw-bottom-for-fun-s 0.2mm Layer Height 2 Perimeters 5 top and bottom Brim My goal was to…
Mount the Lupine Piko Light to your GoPro compatible accessories with this adapter. I recreated the original Piko mount shape to allow for the same range of up/down swivel and added the GoPro base to it. Try to print this in a horizontal,…
My Daughter requested star pattern grips, so I made some. Printed in TPU, with the hole in them for tassels! Fits the standard bike handle bars. but you can scale them to fit yours. a good test is to just lower it through the bed before…
This model is compatible with the lego system.
UPDATE 27/05/2022 Added the other parts of the original file, simplified for faster and easier printing. Added some instructions for the top parts, see image You need to print: z axis brace top right z axis brace top left z axis brace…
I created this after scouring the internet. Since I could not find a model I created one with dimensions taken from my broken parts. For best results run a 3mm tap through the holes before installation. I posted all the models I've made…
Simple 3D library for openscad that makes it easy to generate the most common bar and tube profiles. See also: " https://github.com/quirxi/BarsAndTubes ". Print instructions Category: Other Summary Simple 3D library for openscad that…
Easy to install rain protection for your feet. Fits Harley Davidson TOURING 2024+ I recommend printing with high-temperature materials. Use four wall outlines
These are supermoto bar ends used for crash protection. They are designed for use in threaded handle bars that accept an M8 x 1.25 thread pitch. You will need a 40mm long hex drive flat head bolt to install each end.…
For the “Whoa-Club” that navigates in the gray of the USMC! Can be used for the US Navy and US Coast Guard Warrant Officer ranks by using a different color for the blocks. If using an FDM Printer, in particular using PLA, I recommend…
Fulton Woodworking Tools and Accessories (and maybe other manufacturers) make 4 way pressure clamp kits like this one: https://www.amazon.com/dp/B073QSF8JR They include a small number of notch bars, which allows some adjust-ability in how…
These are 3d Printable Gloomhaven board game initiative tracker bars. Like Jaws of the Lion these are little bars with the baddies and heros names on them to help keep track of who goes next. I am not affiliated with the companies that…
This is a versatile clip designed to securely hold rods, pipes, or handles of various diameters. It features a countersunk hole for easy wall mounting or attachment to other surfaces, making it ideal for a wide range of applications.…
The Paperwhite is very light weight but very hard to hold. These grab bars solve the problem. I liked these 2 designs, but they didn't work for me. They inspired me to create a new model.…
GoPro holder for 22mm handlebars I was looking for a solid GoPRO mount for 22mm handlebars. I was very interested in the remix https://makerworld.com/en/models/841829-smartphone-mount-for-22mm-handlebars-e-scooters#profileId-788194 and…
Remix for Garmin Mount for Rose XLITE Aero Bars.
I created a small set of handlebars to add to my inokim scooter for my son. NOTE: I do not recommend riding with a kid like this, as it doesn't seem very safe! I walk with the scooter while he's holding on to take him to kindergarten and…
These STLs contains necessary items to print : a bed LED bar with its stand ; a high LED bar with its stand ; a switch button stand integrated on the side of the PRUSA control panel. The power button is illuminated with a LED blue ring…
IMPRIMIBLE EN TRES COLORES CON UN SOLO EXTRUSOR AL ESTAR DISEÑADO CADA COLOR POR CAPAS
I added a different design to the side so it wouldnt let any small fish to squeeze into the big holes.
Um die Aluminium-Teile der metrischen Caliburn-Version von PrintStructor möglichst exakt bohren zu können habe ich die notwendigen Teile aus der mitgelieferten Step-Datei extrahiert und in kleine flache Teile aufgeteilt. Eigentlich hatte…
Easy to install protection for your carsh bars. Fits Harley Davidson TOURING 2024+ I recommend printing with high-temperature materials. Use four wall outlines.
I printed as positioned, with the diagonal end on the print plate. This gave a nice combination of strength at quality at 0.24mm layer height.
Simple little lightbars to house a 10x200mm LED strip. Perfect for enclosures. I was unhappy with the original lighting in my Ikea Lack Enclosure because it was misplaced and left the hot-end in shadow. These simple little lights fix the…
Holes added on the bottom for M4x8 threaded inserts
Push up bars for your calisthenics routines. I mainly use them for push ups as my wrists suffer a lot doing them. Main body printed in PLA, 8 or + perimeters and +50% infill. Flexible base printed in flexible filament to have some grip…
Cherry MX space bars with space icons - space shuttle - meteor - sun - star - moon blank space bar by Matej2510 space icons by Font Awesome - space shuttle: Font Awesome Free 5.2.0 by @fontawesome - https://fontawesome.com - meteor: Font…
This model is compatible with the lego system.
This model is compatible with the lego system.
I needed a solid mount for my Beeline to mount on the bars of my Triumph. Bought the Garmin “out front” mount and then realised it didn't fit the 25mm bars. Oops, so I printed this with PETG. You will need 2 of 35mm M4 plus nuts to close…
I use bar end extenders on my bicycle's straight handlebars. I wrap the extenders with padded tape (for cushioning). Recently on a ride, the compression fit end plugs that were provided with the extenders came loose and the tape started…
Slight modification of the blendr Duo by dar3kg . This is easier to print, and won't split when you try to fit it over the handlebars. I've also added material underneath the handlebars so the mounts won't slide apart. This fits my Trek…
To assemble you will need M4x25mm socket head screws and M4 nuts.
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
![Garmin Mount for Aerobars [parametric]](https://media.printables.com/media/prints/878658/images/6738792_8b57a8b9-5bd2-4d0c-9765-a5bec375e787_55f80f7d-9ae8-4304-b229-628c4828e804/20240513_114330.jpg)
