Counting matching models…
This is a vertical 1 inch template for the pantorouter. It installs and uses the same bit and guide bearing as the factory templates but mounts vertically. It prints easy but will need supports underneath on the bed. The embossed text…
RU: Версия для другого экрана Отличия: кнопки сделаны вертикально, не сделана подставка. Важно - в файлах версия для использования вплавляемых гаек. Из-за странного, на мой взгляд, расстояния между осями крепления - предлагаю сначала…
Use 2 x M3 screws to mount your ThinkCentre Tiny to your 10 inch rack. The backside ports will be facing you for easy access. The 2 x 2½ drivebays are optional. Verified on models: M920q M920x M720q. I used this SATA controller in the…
Printed these upside down using 0.4 mm nozzle with PETG and PLA. The (TPU) seal goes in the lid. Use a 5" hole saw to install. Added cover with webbing for installation require higher weight load. Added blank cover with no finger holds.
This saddle t-square allows you to run lines parallel with an edge or perpendicular to it. It wraps around corners so you continue a line down an edge. The diamond shaped wholes keep your pencil centered to the line you're marking and…
Case for LilyGo Ts-4.7 Inch S3 E-paper board. Facilitating 18650 battery (with a separate holder) Board button access USB connector access
This is a 1/10th scale compressor and rattle gun for the workshop as decoration or other. The rattle gun is Snap On style and would usually be red and comes with a 55mm nut that would usually by black, the compressor is made as to be…
A 19-inch, 2-part, modular rack mount for the new Ubiquiti Unifi USW-Flex-Mini 2.5G 5. This mount is part of a 19-inch modular rack mount system I designed, you can mix and match the modules with other mounts. Take a look at my models…
Adapt your 100mm (4 inch) air duct to a 150mm (6 inch) duct, with option to add an inline 140mm PC fan. To install: Print one of each part Insert M3 threaded inserts into the 4 outer holes on each side of the middle piece Use four anti…
Deep Strike 9-Inch and Embark 3-Inch markers for 40K or similar games. You can print in two colors, doing a "filament change" at a specific layer. Check my other designs for the 3-Inch "Embark" marker. Mirror from…
"Grinch" Cookie Cutter Cookie cutter is made of 2 parts - cutter and inner stamp. Parameters: Stamp - 62mm x 73mm x 4mm Cutter - 71mm x 82mm x 12mm TIP: I recommend to download also cookie cutter holder for stamp and stick with glue to…
Original document holder must be modified. Use double side tape (or glue) and 4 screw for each side. Print twice (one mirrored) It is for 7 inch 1din radio. Might be used for 2 din (I didn't try it)
One of the cheapest options for dust collection in home woodworking shops is to use readily available and cheap PVC drain pipe. The problem is that most dust collection fittings are not made for these pipes (though that seems to be…
Nachdem ich bereits eine Variante in Holz erstellt habe, nun nochmal das ganze als 3D Druck! Viel Spass beim drucken! Falls der Schieber zu stramm funktioniert, etwas Fett auf die Reibestellen geben. Gerne Bewertungen und Fotos..…
This is an extrusion frame mount for the Chitu 5 (v5) touchscreen (RXA-050001 model). This features 5mm mount points for your convenience. The face plate and the board half mate with each other, eliminating the need for glue. Screen:…
This is a frame for a round pin - a round pin that uses a central pin backing. I had some pins made for Solstice, but their single pin backing (a "rubber pin back") isn't overly great. The pin comes out and gets lost. I designed this pin…
This is a newer model of my original design: https://www.printables.com/model/798718-hueforge-funny-chinchilla-sign This is a funny sign that I made and have placed next to my chinchilla's cage! We refer to her as a potato quite often,…
This is designed to be used with heated inserts, the size I used is 1/4“-20x12.7. But any ¼ inch insert should work, as long as it's not longer. The ones I used: https://www.amazon.de/dp/B09MTS6ZZQ It's a very simple and convenient way to…
The mount is designed, to use a heated insert like this one https://www.amazon.de/dp/B09MTS6ZZQ The size is 1/4“-20x12.7 but anything shorter should work just fine.
Pretty basic model. I made the base thick so it would fit nicely in my window and have a little weight so the duct wouldn't keep pulling it out.
I'm continuing my effort to transfer the 3Dsets.com model 14 “Long Max” into an expedition vehicle. As a long-time player of Spintires/Mudrunner/Snowrunner games, i know pretty well, that there is no off-roading without a winch, so I…
3.5 inch Event Day Counter / 9cm Tage-bis-zum-Ereignis-Zähler When you need to display a certain amount of anything (remaining days until event; pieces in Stock; days until retirement etc.), you probably prefer a simple compact display…
(EN) Character from the movie Grinch. Suitable for hanging on the wall. The piece has a small hole in it. Be careful, it is fragile. (CZ) Postava z filmu Grinch. Vhodné k pověšení na zeď. Díl má v sobě malou díru. Pozor křehké.
Here is the model for Grinch Bear. The Grinch is a reluctant acquaintance of Barry, and he seems to be willing to tolerate you too, do you have space the Grinch? just keep an eye on your Roast Beast. I hope you enjoy, and Merry Christmas…
I normally publish and update all my models at MakerWorld. They are only here on Printables to keep the accounts consistent. Please download the newest version here at MakerWorld. The box has a depth of 40mm which should be enough for…
I had a problem. Fusion and some filament solved it. Please check your codes. In most Countries plastic components that are used in mains voltage locations are required to be made from a flame retardant material. You have been informed…
The Mastercool pumps have an exhaust vent that doesn't allow any attachments. When I was drawing a vacuum on large chambers the pump was filling my garage with mist. I tried sponge filters, duct taping filters on, and nothing was working…
Einfache HDD-Storage Box für 7 Festplatten. Gedruckt mit PLA auf einem Ender 3 V3 KE mit 15% Infill
I frequently use my metric set of ¼" deep sockets and very much dislike the socket rail that Harbor Freight provides, so I made this after being gifted a small set of DeWalt ToughCases filled with driver bits and struck with inspiration.…
Modular Hydroponic Tower made for 2inch Net Pod this is the best model as of now and its a world of difference with the other one. the fact that you dont need to spend hundreds of hours more to print the net pods, simply use cheap…
Ce support très léger permet de maintenir l'iPadPro M4 11" (2024) and M5 11" (2025) AVEC une coque à “JETech Coque Clair pour iPad Pro 11 Pouces M4 (2024)” https://amzn.eu/d/hUI3W5y (12€) Les angles possibles sont 5°, 40° et 65° 5° idéal…
Need a 4-inch fume extractor exhaust connection for your Voron 2.4 or Trident? This magnetic 4-Inch Voron fume exhaust connector remixes the ring from JCShumpert 's Magnetic Fume Exhaust (4 inch duct) for EnXLosure Backpanel for use in…
Stand for GDEM1085Z51 1360x480 10.85inch Black,White,Red e-paper display More information, about the hardware and software, can be found on on github . You need two stands, one of them mirrored in the y-axis in the slicer. Print the…
This version has these improved features: hinge that snaps the box top and bottom together two box tops - one that prints as a single part and one that is stronger, but requires simple assembly ramped front catch text for multicolor…
After a lot of frustration with off the shelf cable organisers and other methods, mostly fixed with screws in cage nuts, I decided to make something that can just click in place. Then I realised that I might want to take it off again, so…
A 6-inch rack mount for the Unifi USW-Flex-Mini. This model is part of a series of 6-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a coffee ;) Print Settings Rafts: Doesn't…
7.62×51mm NATO is nearly identical to .308 Winchester, and is the same caliber used by the Halo MA5B assault rifle. -Use for cosplay, short films, display piece, etc. -Should not be used with real firearms -Please use responsibly Print…
This is a single piece, clip/holder I designed for my dust collection hose. Its a 2.5" clear flex hose. The only hardware you need are the screws to secure it to a flat surface. Cheers [NjB]
Bastion mods: -btt octopus mount with and without mosfet mount -cables and ptfe (M6 coupler) relief -PSU cover with and without charger mount (for Rpi) -5 inch screen mount -Rpi3 mount -bastion logo diffuser for dragonburner I also…
3mm blank i use to manage cable with PVC cable tray plate mod come with small hook (R6mm) check in mods folder or make something to hook check diy folder If you enjoy my work, please consider support at link in profile.
We were fixing a 1958 Mattel Toy Winchester Rifle and needed a replacement part so I created a copy in fusion. It seems to be working fine, but not sure on longevity as the original was metal. Layer Height: 0.16 Infill: 100% Supports: Grid
To prevent the protective jaws from breaking, it is important to use a ductile, non-brittle material. Adjust thickness of rim flange to your needs in your slicer. Print instruction: material: FLEX hard or ductile ASA, PETG supports: no…
7.25 multiple saw blade holder. Safely store your saw blades and have extras on hand when needed. I like to carry old blades with me for cutting MDF OR VINYL.
I originally made a modified 6 pod section which has integrated mounting tabs but figured a mounting section which attaches to the regular 3 or 6 pod section would be more useful. Uses 4x M5 bolts and nuts to mount.
How to generate label read in 10 inch Keystone Patch Panel with Label description It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill…
It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…
A 5 and 6 inch version of a Tenkara Line Winder featuring hook holes with a backer to keep hooks away from your furled leader lines. Fits the Dragontail Shadowfire 365 rod. Printed on back (hook holder holes down on printer bed) with…
Click to Read About 6.5 inch and Rack Frame 6.5 inch Rack Mount Collection It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on…
This is a work in progress. I have not printed this yet (waiting on filament) This should fit the 10 inch rack with minimal fuss. As the title and summary say, this is a standard 10 inch panel that was remixed to hold a Raspberry Pi 4,…
These prints are used to make wing-nuts when combined with the appropriate size hex nuts. Note : For related Thumb Nuts and other knob and screw related prints see this collection : https://www.printables.com/@kaje/collections/719205 The…
First, let me say I am sorry about the image quality. This is a filament shelf bracket designed for ½ inch dowels. It was modified in FreeCAD. I would print this using at least 4 top/bottom layers, 3 walls and 20% infill (I use infill…
Adapter for 7 inch felt filter bag to attach to a 1 1/2" PVC connection for use as a pool slime bag or dust filtration. I made this adapter for this 7" X 32" felt filter bag: https://a.co/d/hf8bH57 This had a plastic collar that this…
Have built 10 inch rack and to clean up the wires made this plate. Optimized to be printed without any supports and whatever settings you wish. Here is video in case you want more context:
This is a fitted 10" rackmount for the Ubiquiti Unifi Express 7. It has cutouts for ventilation, and a bottomless design to accomodate the router without going over 1U in height. The fit is fairly tight, but shouldn't be a problem. If…
I have an inline bathroom exhaust fan, but needed to connect it to three vents without running back to the store. Glue and fit the panels. A blanking plate model is included if you don't need all four.
Adapter allows Solar System Lithophane collection using m75x4 threads to be mounted to 4 inch ceiling light fixtures using e26/e27 LED bulbs. Both parts can be printed without support. The adapter allows for rotation of Solar System…
1/8 scale remix, M3 screws needed. 2x M3x8mm + 1x M3x12
i wasn't satisfied with the small touchscreen available and went for a hunt on aliexpress and found this little gem. Only drawback is the somewhat huge bezel, i tried to keep the bezel as minimal as possible to not further increase the…
Upgraded articulated print-in-place ruler, now also on Printables! I use this for wargaming, the starting end is curved to fit nicely to a model's base. Upgrades: The joints of pieces are now positioned so that smaller lengths can more…
This is a 10" rackmount for keystones as well as separate accompanying panels for labelling said Keystones. The label strip can be placed above or below the Keystone panel. Required hardware: Screws and cage nuts that came with your…
Cover for power button or any modified key, i add switch to replace the power button on my m-atx with soldered pin switch connected to 2 pin power switch in motherboard socker.
Sailwinch Servo Drum 40mm ready to run on a Basic Futaba disk Horn of 20mm single track. 40MM DIAMETER, I will setup for a 10 Turn Servo. M3 servo drum lock M2.5 Horn lock This a remix of https://www.thingiverse.com/thing:2583624 Ready to…
This is a panel for a 10 inch rack with cutouts for 4x 9 pin dsub (db9) connectors and a Powerpole connector. Tested with 0.8mm nozzle only Parametric allowing tweaking of most of the dimensions to suit alternative components
These caps are intended for use with my 2.5 inch Twist Lock Dust Collector Hose Ports. Both male and female versions are provided. Like the hose ends themselves, these have been modified to make installation and removal a little easier…
Here is my take on the Classic Battlefront 2 DC15A rifle for custom 12 inch 1:6 scale action figures. I did my best to be as true to the design as possible despite lack of decent reference images, just in more of an HD high poly format.…
2U SFX PSU mount for 10-inch racks. Useful when converting a MiniITX workstation into a rackmount server and wanting to reuse as many parts as you can. I printed using PETG-CF .15 layer height 2 walls Tree Supports on Build Plate so the…
This is a simple, support-free bracket for mounting a network switch in a mini rack. Easy to 3D print at 0.2 mm layer height, it fits most standard printers and keeps your setup neat and secure. Switch dimensions are 160x35mm. Model…
Use this to add a 1/2 inch tube extension to your Klein wire and cable pulling lubricant . I used this tubing: Eastman 3/8 Inch ID (1/2 Inch OD) PVC Clear Vinyl Tubing, 20 Foot Length, 98566 . Assembly Directions: Cut desired length of…
Heres a small winch to put on tiny e-motors I made it parametric to easily change or adapt to bigger things
A 19-inch, 2-part, modular rack mount for the MikroTik CRS305-1G-4S+IN switch. I have included two variations of this model, one meant to mount the switch if you already installed its rubber feet, and another for those who haven't…
Please Check Out all my other Gridfinity Tool Holders here ! :D ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 3x2x3u Gridfinity Socket Storage for: - Harbor Freight QUINN ½ inch drive Sockets and ½ inch extension,…
🪴 3" Square Planter – Built for Real Growers ***NEW*** Drip Tray: https://www.printables.com/model/1484429-3-planter-tray-smooth-finish-print Don’t let the clean lines fool you — this square planter means business. Designed with…
We had a hose clamp break on a Platypus water filter. I had one on another filter (black one) to work from, so I designed a replacement to match the original (white one). The textured part was add using paint on fuzzy skin. You can…
Print in PETG or PLA but I recommend PETG since you are likely to get oil on it if you are going to use it for automotive work. I recommend printing the box, lid and latch with “Fuzzy Skin” applied only to contours, I use 0.3mm point…
This is a 1U hard drive tray designed to hold two 3.5" HDDs, compatible with 10-inch server or network racks. Category: 3D Printing
This is a 10 inch ½ U mount for the LG BP60NB10 Ultra Slim Portable UHD BluRay drive. Updates 2025-10-08 Made the bottom plate solid with grooves for the drive feet Added 2 new versions of the mount Standard version has the mounting holes…
Collection of 10 inch blank Panel with Voronoi Pattern 1-3U These Models have a finer pattern than my first model with the Voronoi pattern Print as you like, these models are not for structural integrity.
Description 10-inch Rack Mount for a MiSTer FPGA with 1U height. Designed for a full stack MiSTer setup, which includes a IO board and a USB board. This mount is compatible both with the original MiSTer FPGA and the MiSTer Pi clone. If…
I recently picked up a Sovol Zero for some high speed printing and was disappointed in the stock screen / knob interface, as well as the Factory Sovol 5 inch screen upgrade (which works perfectly, but just looks weird being so large on…
Some Top Panels to fully close the gaps in the Modular 10inch Server Rack when using the topper and Handles. The standard is always 3mm thickness. But if you are usind the Multiboard Add-On, then you will need the wider 6mm frontpanel and…
I've included the f3d file in case you have fusion and want to adjust the spacing. I had to space mine out 4 inches to clear my neighbor's fence. The included STL is 1" thick in total. I recommend PETG if it's going to be exposed to sun…
Model 1 is an ¼ inch to Quadlock base adapter. You can combine Model 1 with any of the original quadlock mounts (e.g. magsafe or charging heads) or print a basic one yourself (Model 2). No supports needed. Printed with 0.10mm Layer…
8-inch carbon truss newtonian telescope 8 inch carbon truss telescope Esay secondary mirror control ( Betty’s Secondary Mirror Holder style) Losmandy type dovetail bars Primary mirror D203F750 , D203F800, secondary mirror 70mm support 200…
I recently made a tool organiser using Bento3D and I wanted to store both 4.2mm and ¼ inch screwdriver bits in one holder. So I remixed my older model to accomodate both sizes. I printed in TPU because it has enough grip to hold the bits…
Lucky 7inch by clover fpv. Bando boot ready for banger Fits 2808 and less
This kit improve; the access to the block with is angle, the bracket better fixe of the hose to the wall with nice look and one of the bracket can hold the blow gun whit metal tip and plastic handle. All made in PETG.
A nice desktop case/stand for a 4" LCD TFT screen. My use case was for displaying various info from a Pi5 via python scripts. Here is the LCD used for the model: https://www.amazon.com/dp/B0CKRJ81B5 The “Box” is designed to accept (4)…
Wanted to incorporate another model in my setup. This time instead of modifying or modeling the rack mount shelf, an existing OpenSCAD library suitable to the purpose was used. Found https://github.com/wildegnux/universal-rack-shelf in…
Based on my earlier tool this one has the 145 mm and 184 mm spacing for Nexus 5 and Alfine 8/11 hubs. The text has been added in the slicer and would require one filament swap to print. When tightening down the nuts on either side I…
imported to fusion and made to be flat on the bed and not need unneccessary supports.
Das GoFlyPro Frame wurde weiterentwickelt um die DJI O4 Pro und das Walksnail Moonlight Kit einzubauen. Es werden hier nur die benötigten Dateien für die GoFlyO4Pro Drohne hochgeladen. Es ist sozusagen einfach nur ein Upgrade und baut auf…
After creating a similar exhaust adapter for my Core One, I decided to design one for our office's Qidi Q2. This adapter takes the Qidi Q2 exhaust to a 120mm PC case fan, with another adapter to 4" exhaust hose that will be run to a roof…
(NOTE: PLEASE REFER TO LAST PICTURE FOR CORRECT SIZING SETTINGS BEFORE PRINTING) make your own sheetmetal half round gutter downspout starter pipes with this jig. this jig is designed for you to stuff a piece of 11.7" paper or pipe…
Keep your 1/4 inch drive socket set neatly organized and easily accessible with this improved holder! This V2 version features chamfered bottom edges for enhanced print quality and includes 3MF files for easy multi-color printing,…
Keep your 1/4 inch drive socket set neatly organized and easily accessible with this improved holder! This V2 version features chamfered bottom edges for enhanced print quality and includes 3MF files for easy multi-color printing,…
