6,562 models
I was fed up with the Velcro-mounted window seals made of fabric. Firstly, the Velcro gets loose when the window heats up in the sun, and secondly, it wasn’t easy to mount and was never securely mounted. I use a portable air conditioner…
Print approx. €0.42–€0.52 excl. taxPreliminary estimate for PETGSource material: PET
360° Spinning Adapter for the Multifunction Arm Mounting System What you need Multifunction Arm mounting system (Small Arm System) Big Clamp For Small Arms This Spinning Adapter Side small-NUT-M3.stl (1x) screw-small.stl (1x) Hardware…
Print approx. €1.28–€1.56 excl. taxPreliminary estimate for one variant
Looking for additional storage space and ways to extend the use of the Ikea Skadis organizer? This shelf mounts on top of the Ikea Skadis board and adds 190x 80mm of storage space without loosing the use of the upper holes. 4 shelfs will…
Print approx. €5.00–€6.11 excl. taxPreliminary estimate for one variant
Simple Vase Mode Christmas decoration with traditional mounting hole. Take the mounting wire and cap of an old or broken Christmas ball and insert it in the cylinder. Available for 8mm, 10mm, 12mm and 16mm mounting cylinder. I used 8mm.…
Print approx. €4.40–€5.38 excl. taxPreliminary estimate for one variant
Mounting bracket. Recommended to print with a 0.4 nozzle with a layer height of 0.2 or less! For material, something that's more resistant to heat than PLA is advised. Commenter @jornthree_2921709 recommends PETG or ASA. I've used a PLA…
Print approx. €0.81–€1.00 excl. taxPreliminary estimate for one variant
This is somewhat a remix of a remix. Crosslink did a remix for the Ender 3 V2 of 3D_LC's mounting plate . I didn't like to use the roller screws to mount this neither did I have any use for the cable routing channels as they can only be…
Inspired by the Xbox One S controller mounting clip, this clip is designed to snuggly snap around the 8BitDo Ultimate bluetooth controller. Based on a 3D scan of my controller, it fits best by hooking the clip to the top, and then…
Print approx. €2.20–€2.69 excl. taxPreliminary estimate for one variant
180° Tablet Holder Hinge for the Multifunction Arm Mounting System (Small Arm System) What you need Printed parts Multifunction Arm mounting system (Small Arm System) Multifunction Arm mounting system Spinning Adapter Big Clamp For Small…
Print approx. €3.00–€3.66 excl. taxPreliminary estimate for one variant
Plate locks the Nest doorbell down, replacing included metal plate. Use the key: https://www.printables.com/model/466189
Print approx. €0.40–€0.49 excl. taxPreliminary estimate for one variant
Made at the request of a Printables community member, these mounts are a traditional mounting bracket with dual offset screw points. These mounts are best used with typical flat bottom soffits. If you have angled soffits or rafter tails,…
Print approx. €0.12–€0.15 excl. taxPreliminary estimate for one variant
This mounting plate results in a very robust mount for the DJI RC remote control, such as those offered for the DJI Mini 3 Pro drone. The mount is tailored to the remote control and intended for outdoor use, especially on bicycles. Note:…
Print approx. €1.19–€1.45 excl. taxPreliminary estimate for PETGSource material: PET
These are some bracket designs for holding a Master Cooler QUBE 500 PC case to the underside of a desk. This is ideal for people like me, who have an already cluttered standing desk and don't like cables reaching to the floor. There are…
Print approx. €9.15–€11.18 excl. taxPreliminary estimate for one variant
Plate mounting bracket for 7" Touchscreen case for Raspberry Pi 5 + slim version , 7" Touchscreen case for Raspberry Pi 4 + internal fan or 7" Touchscreen case for Raspberry Pi 3 (B/B+) + internal fan . Features Thread inserts Display…
Print approx. €3.61–€4.41 excl. taxPreliminary estimate for PETGSource material: PET
Cable Clip for the Multifunction (Small) Arm mounting system Features Fits on the “ arm-small-hex-honeycomb-wall-compatible ” Fits 4.50mm diameter cables
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for one variant
Tablet Holder for the Multifunction (Small) Arm mounting system Features Fits tablet-holder-small-[L, R] Fits a Galaxy Tab A8 Change Log 2025-01-01 Added the Step file as requested by @Ferrugius
Print approx. €0.68–€0.83 excl. taxPreliminary estimate for one variant
A versatile, low-profile ceiling canopy system with a height of only 3 cm, suitable for various mounting situations. In case you only look for a holder for your existing canopy, also check the @mikhart remix for 10cm canopys Available…
Print approx. €3.04–€3.72 excl. taxPreliminary estimate for PETGSource material: PET
Multiboard connector for items with mounting points for regular screws. Can for instance be used to connect Ryobi chargers to Multiboard. Recommended print settings (same as Multiboard defaults): 3 wall perimeters in wall thickness 15%…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for one variant
V-Slot profile 2020 mounting bracket for 7" Touchscreen case for Raspberry Pi 5 + slim version , 7" Touchscreen case for Raspberry Pi 4 + internal fan or 7" Touchscreen case for Raspberry Pi 3 (B/B+) + internal fan . STL-Files for…
Print approx. €2.97–€3.63 excl. taxPreliminary estimate for PETGSource material: PET
Variation on the Vesa mount for the Multifunction Arm. This part allows mounting a screen to the side, rather than the end of the arm, which is especially useful for multi-monitor setup. Use together with the “Base-small-with-holow-M3”…
Print approx. €2.63–€3.22 excl. taxPreliminary estimate for PETGSource material: PET
Needed universal 3,5" mounting bracket for SSD. I added any mounting holes I could find datasheets of.
Print approx. €1.95–€2.38 excl. taxPreliminary estimate for one variant
This is a small weather shield I created for an outdoor temperature/RH/barometric pressure sensor. Prints without supports (upside down). The mounting is designed to fit a common breakout board style used for the BME 280 sensor, though…
I needed an easy way to hold a DIN rail to the side of my NavePoint 15U wall mount open frame server rack. These parts allow you to mount the DIN rail on the side of the rack with a slotted endcap to help adjust for a variable length rail.
Print approx. €1.34–€1.64 excl. taxPreliminary estimate for one variant
Please see my updated version of the Rosahl M-1J1R mounting cover , which simplifies overall assembly, especially the USB-C power supply module can be assembled in advance (or ordered fully assembled!), snap-fits into its compartment and…
Print approx. €4.54–€5.55 excl. taxPreliminary estimate for one variant
With this plate you can mount your foil in seconds, since you don't need to fiddle around with the screws. Position the slot nuts roughly in the right position, then click in the plate. Now the mounting plate holds the nuts in position…
Print approx. €2.36–€2.88 excl. taxPreliminary estimate for PETGSource material: PET
Soap holder with 60 mm round base that fits the standard wall ring mounting
Print approx. €5.55–€6.79 excl. taxPreliminary estimate for one variant
A simple under desk mounting solution for the Focusrite Scarlett Solo (4th Gen) audio interface. I couldn't find any solutions that I liked for mounting, so I designed my own! This is also designed using Zoo's modeling app ! The included…
Print approx. €5.62–€6.87 excl. taxPreliminary estimate for one variant
Final release after more than 6 months of developing and testing! After a several month long beta process and countless improvements (especially of the auto-rewind mechanism) the complete EMMS works 100% reliable for month now. It took…
UPDATE: (2024-11-25) I have added a version of the underslung right bracket with a full protective cover for the PD board. I have previously created a 22.5° remix of the MMU2 brackets due to my use of a cabinet and feeding from above.…
Print approx. €2.34–€2.87 excl. taxPreliminary estimate for PETGSource material: PET
This is a fully scaleable hook. In default configuration the hook has 75x50x19mm in its size. With the fusion file you can scale it as you want.
Print approx. €0.71–€0.86 excl. taxPreliminary estimate for PETGSource material: PET
I used wood screws and mounted it directly to the wooden board. Power supply uses similar bracket. Also cables are held up with zip ties using this easy print: https://www.printables.com/model/205265-cable-management-easy-solution
Print approx. €9.30–€11.37 excl. taxPreliminary estimate for one variant
I used to use @OneTrueMyth's Deluxe Tool Caddy for my Prusa Mk3S. Recently I put it into a LACK enclosure, which isn't large enough to hold the tool caddy. Perusing the usual sites, almost all tool caddy models for the LACK enclosure…
Print approx. €0.14–€0.17 excl. taxPreliminary estimate for one variant
This case allows you to (manually) adjust the focus of a Trust Trino HD webcam (available for ~€10 on Amazon ) and mount it on a flat surface, rotatable in one or two axes (tilt or pan and tilt). With this case, the webcam becomes quite…
Print approx. €0.16–€0.20 excl. taxPreliminary estimate for PETGSource material: PET
This is a camera cage and tripod adapter for the HIKMICRO Mini2Plus V2 thermal imaging camera module. The combination of a thoughtful design and a specific material choice results in a ¼-inch mounting solution that is both easy to print…
The Multifunction Arm system is fantastic, but, being made from plastic, not 100% rigid. Gravity, on the other hand, is a bitch, and won't hesitate to flex and bend the system until your screen or other device on the end of the arm is not…
Print approx. €0.27–€0.33 excl. taxPreliminary estimate for PETGSource material: PET
Double and triple Loxone Mounting Brackets (https://shop.loxone.com/enen/mounting-bracket-double-silver.html, https://shop.loxone.com/enen/triple-mounting-bracket-silver.html) have non-standard box spacing of 98 mm. Installing three…
Print approx. €1.13–€1.39 excl. taxPreliminary estimate for PETGSource material: PET
Designed this to mount an aftermarket ESC in my 4x4 Rustler (Hobbywing Xerun XR8 SCT in my case, let me know if you try some others so I know which do/n't fit). I printed mine in PETG, but PLA will probably work fine too.
Print approx. €0.65–€0.80 excl. taxPreliminary estimate for PETGSource material: PET
This is a rigid arm designed to mount to the z axis wheels of the Anycubic Kobra Neo. It has a 7mm hole oriented vertically at the end that fits a standard Gopro style camera mounting screw (the type you would use to attach it to a…
Print approx. €2.31–€2.83 excl. taxPreliminary estimate for one variant
Havis console mounting Motorola APX-8500 Mobile Remote Head Mount UPDATED POST size requested per @SeanOConnor_5174100 I modified the 3" deep version to 2.5". I have not printed it, but it should work fine. The 2.5" version is named with…
Print approx. €6.32–€7.73 excl. taxPreliminary estimate for one variant
This mounting plate was modeled to be the base for a drone remote control for my bike. I didn't want to mount the remote control on the bike handlebars because I don't have enough space and it just didn't feel right.... ;-) So I decided…
Straightforward and reasonably quick print with 0.3mm default settings. Supports required under mounting wings. 0.150" holes for screws. Shown here in Flashforge Rainbow PLA. The power supply has the same dimensions as the dock itself and…
The default Reolink mount is designed for mounting to a wall with masonry screws or wall anchors. That's fine, but some applications need a clamping surface instead. This is particularly the case if you want to mount it onto a gutter, on…
Print approx. €1.25–€1.53 excl. taxPreliminary estimate for PETGSource material: PET
This is a mounting cover/frame for a Rosahl M-1J1R electric dehumidifer membrane which can be used for a filament drybox of around 20-30l for multiple spools. Along with a USB-C power supply module it's a convenient and low power…
Print approx. €1.30–€1.59 excl. taxPreliminary estimate for one variant
This is a mounting cover/frame for a Rosahl M-3M1R electric dehumidifer membrane which can be used for a filament drybox of around 50-70l for multiple spools. Along with a USB-C power supply module it's a convenient and low power…
Print approx. €2.20–€2.69 excl. taxPreliminary estimate for one variant
All you have to do is draw a line where you want to be the middle of the shelf, than put jig on and center it with the line. All you have to do is just screw it up. I recomend to print model 4 times, it provide stabilization on each…
Print approx. €7.56–€9.24 excl. taxPreliminary estimate for one variant
This part is used to attach the Quick-Rack to the frame with an M5 cylinder head screw with a minimum length of 25 mm. I printed the model horizontally with carbon filament. This requires support but significantly increases the stability…
Print approx. €0.52–€0.63 excl. taxPreliminary estimate for PETGSource material: PET
This is a helper to make mounting the snap connectors for the Gridfinity base with snap connectors by @Neel_18926 easier. In order to use it (see images) But the snap connectors onto the rail Push them to the center Put the helper onto…
Print approx. €0.46–€0.56 excl. taxPreliminary estimate for one variant
Best to print with PLA or PETG I made this model to help out a friend in need of smoke detector installation! I borrowed one of the smoke detectors to make this bracket!
Print approx. €3.11–€3.80 excl. taxPreliminary estimate for PETGSource material: PET
Simple mounting hooks to screw on to boards, tools and accessories and mount them easily and flexibly to for standard consumer grade heavy duty/heavy load shelves. They work either on the in or the outside of the shelve systems. To change…
Print approx. €0.28–€0.35 excl. taxPreliminary estimate for one variant
I have designed this because I was tired of inserting the threaded insert not straight. With this tripod you can push in every insert staight. Bill of materials: 1x Igus drylin® W double rail WS-10-30 1x Igus drylin® W assembled carriage…
Print approx. €4.81–€5.88 excl. taxPreliminary estimate for PETGSource material: PET
Simple lightweight mounting bracket 200x200x15mm for countersunk screws up to 5mm diameter. V2 is a more robust version. Print instructions Printed with PETG and layer hight 0.15mm. No support needed. Happy printing!
Print approx. €5.69–€6.96 excl. taxPreliminary estimate for PETGSource material: PET
I used PETG as I'm hoping it will better survive distortion from summer temperatures, but I also tried PLA and the part is more than strong enough for the possible abuse it will get from my dog. Printed on edge (cable cutout down) using a…
Print approx. €2.89–€3.53 excl. taxPreliminary estimate for PETGSource material: PET
This model allows a mounting of the Kistenberg's TRUCK STORAGE BIN 12 (KTR12) on perforated wall steel plates produced by the Element System. The KTR12 box:…
Print approx. €2.20–€2.68 excl. taxPreliminary estimate for one variant
Just a simple latch for the external PSU mount. As the cables create some torque on the PSU, it has a tendency to slip outwards. This latch just stops it from doing that. This complements the nice model by @bradbee_329977 to mount the MK4…
This model allows a mounting of the Kistenberg's TRUCK STORAGE BIN 16 (KTR16) on perforated wall steel plates produced by the Element System. The KTR16 box:…
Print approx. €2.74–€3.35 excl. taxPreliminary estimate for one variant
This shaver has a very curved handle, so slides around easily in the bathroom cabinet. This holder is easy to print (two pieces, no supports), assemble (requires two M3x10 screws, which go straight into the printed part) and mount (I used…
Print approx. €2.08–€2.54 excl. taxPreliminary estimate for PETGSource material: PET
MikroTik RB5009 mounting bracket, can be installed either way (0 or 180 degrees) 4 x M4 nut and screw (length 40 mm) Recommended to sand with P120 sandpaper and then glue with epoxy glue
Print approx. €3.15–€3.85 excl. taxPreliminary estimate for one variant
Ensures your linear rails are mounted parallel to your 20XX extrusion. Prints < 8min & no extra hardware required! Add a comment if you want it to be adapted to any other linear rail or extrusion.
Print approx. €0.10–€0.12 excl. taxPreliminary estimate for PETGSource material: PET
I love Sneaks' Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2 , but the ideal position I was looking for required me to mount on the Z-Axis far enough away that the connectors were wobbly. This resulted in extremely blurry…
Print approx. €6.10–€7.45 excl. taxPreliminary estimate for PETGSource material: PET
SMA 8mm nut and N-type 19mm nut tool.
Print approx. €0.52–€0.63 excl. taxPreliminary estimate for PETGSource material: PET
Support bracket when using non-standard PSU mounting location on a LACK v2 enclosure.
Print approx. €2.09–€2.55 excl. taxPreliminary estimate for PETGSource material: PET
This design is particularly stable because it is based on two brackets. I used the original M5 thread insert. I removed it with some heat from the original bracket and reused it in this design. I inserted the thread insert during printing…
Print approx. €4.20–€5.14 excl. taxPreliminary estimate for one variant
Just clip in the cover to hide the screws. Happy printing!
Print approx. €0.16–€0.20 excl. taxPreliminary estimate for PETGSource material: PET
Update I made a new mounting cover for the Rosahl MDL-3 membrane, which uses a standard gasket instead of the rubber o-ring and is simpler to assemble. Also the gasket frame fully covers the interior of the case, hence is more protective.…
Print approx. €4.69–€5.73 excl. taxPreliminary estimate for one variant
In my workshop, I was using a pegboard-mounted rod to hang my tapes on and wanted something better. I saw and tried "tape dispenser - side mounted" by book (https://www.printables.com/model/514012-tape-dispenser-side-mounted) but found it…
Print approx. €0.11–€0.14 excl. taxPreliminary estimate for one variant
Tool for mounting spacers for NyloNove adjustable footplates . Required layer height: 0,15 mm Made by hulaj.market
Print approx. €0.05–€0.06 excl. taxPreliminary estimate for one variant
TLDR: 3D Chameleon is a (now) open source 4 filament AMS that can be used with many different printer models. Getting it to work well on an AnkerMake M5 using Orca Slicer (and in a compact space) took quite a bit of tinkering. Bottom…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant
The lights used to come with clips like these, but now only use adhesive strips, which aren't ideal. I like printing them wiht the screw hold facing down and then just using a brim for support. PLA can be a bit brittle, so a little more…
Update 05/23/2024: Now that Frantisek23 has further perfected his design , I definitely recommend his new solution and basically declare my remix obsolete. Since the EndRib_V1b Mini.stl model is no longer available from him in the course…
Print approx. €1.33–€1.63 excl. taxPreliminary estimate for PETGSource material: PET
Insert for reducing the width of the clamp for Multifunction Arm mounting system → https://www.printables.com/cs/model/165239-multifunction-arm-mounting-system. Thanks to the author for this amazing bracket system. You can customize yours…
Print approx. €2.40–€2.93 excl. taxPreliminary estimate for PETGSource material: PET
Pressure fit mounting box for FM Transmitter chip: https://www.amazon.com/gp/product/B08PVBZB8F/ NOTE: YOU WILL NEED TO REMOVE THE MIC FROM THE BOARD FOR THIS TO FIT Resolution: <= .28 Infill: >=20% Filament material: PLA Print with brim…
Print approx. €0.64–€0.78 excl. taxPreliminary estimate for one variant
A Quickfix junction box for Wago terminals is an excellent junction box, but provides no bracket. This design allows the junction box to be mounted to a wall or beam by screwing the mounting bracket then pushing the junction box into the…
Print approx. €0.63–€0.77 excl. taxPreliminary estimate for PETGSource material: PET
zip-tie corners for RoboRIO mounting with screws on 4"oc
Print approx. €2.59–€3.16 excl. taxPreliminary estimate for one variant
Simply single-side Vesa 200 to 100 mounting bracket I made for a mounting solution for an Nvidia Shield .
Print approx. €1.55–€1.89 excl. taxPreliminary estimate for PETGSource material: PET
This is a mounting bracket designed to be used with StanleyB 's Internal active air filter . Once mounted, the air filter slides into place for easy removal to change the filter or replace parts.
Print approx. €1.93–€2.36 excl. taxPreliminary estimate for one variant
Necklace holder for 11 necklaces intended for wall mounting with adhesive mounting. Printed with MK4S on 0.2mm layers using PLA. I suggest adding a layer modifier for the layers that include the hooks to increase to 100% infill for…
Links for Titan Extruder Kit :…
Print approx. €1.77–€2.16 excl. taxPreliminary estimate for PETGSource material: PET
This spoolholder is for wall mounting. Printmaterial: AMAZON BASIC PLA Size: Mount-Arm 80mm After the print you have to cut a thread (M6) in the one hole on the buttom of the “spoolholder2”-Part. You need: 2x Screw for mounting 1x M6…
Print approx. €2.01–€2.46 excl. taxPreliminary estimate for one variant
Needed a mounting bracket for a friends car mobile radio so made in onshape. M4 screws for everything I printed in PetG, Polymake PolyLite. Print it on its face.
Print approx. €0.90–€1.10 excl. taxPreliminary estimate for PETGSource material: PET
This Furitek Slidetech ESC has a cutout on the bottom for airflow and cooling…which is really helpful….except for when looking to double-sided tape mount it to the car. I created this simple mount that allows the ESC to sit off the bottom…
Print approx. €0.98–€1.20 excl. taxPreliminary estimate for one variant
Im Zusammenhang mit dem Bau eines Druckergehäuses ( PrintClosure-Projekt ) habe ich diesen Einbaurahmen entwickelt. In den Rahmen kann das digitale Thermometer-Hygrometer eingeklipst werden. Die Abmessungen des Ausschnitts betragen 46,5 x…
Print approx. €0.20–€0.25 excl. taxPreliminary estimate for PETGSource material: PET
Update: I sent the piece of junk back to Amazon. Wifi connects really easy but the rest was a nightmare. One printer wont read the fake SD card but will home the printer, the other printer, did read the SD and would start the print, tilt…
RepRack wall cleat with keys that slot into key hole mounts on my shelf frame instead of being screwed to the wall. Sliced laying down with supports for the new mounting points and a lot of extra perimeters and high infill. Printed on my…
Print approx. €4.43–€5.41 excl. taxPreliminary estimate for one variant
Yamaha soundbar remote control mounting fixture I wanted to mound my remote to those two aluminium rails on my bed. this is what i came up with. It fits perfect. I also included the Fusion 360 file so you can add your own mounting back.…
Print approx. €1.03–€1.26 excl. taxPreliminary estimate for one variant
I recently bought a UNI-T model LM100 laser distance meter. Unfortunately, this meter is not equipped with a thread for fixing it to a tripod. So I designed a suitable holder with 1/4" UNC thread which allows you to mount this meter on…
Print approx. €2.27–€2.77 excl. taxPreliminary estimate for one variant
I created a simple mount for my Eufy IndoorCam that fits in a top corner of my Prusa Enclosure. It has four holes in it that needs to be filled with threaded inserts for M3 screws. I am using the normal ones from CNC Kitchen but you can…
Print approx. €0.76–€0.93 excl. taxPreliminary estimate for PETGSource material: PET
These mounting brackets are suitable for 30 cm width LED panels with screw holes on the back. The model has high tolerances for the drilled holes in the ceiling. Mounting is very easy. Push the panel to the ceiling and slide it in place.…
Print approx. €2.58–€3.15 excl. taxPreliminary estimate for one variant
I remixed Walletclan3D's excellent storage cubby to reinforce it with ribs for weighted\loading, and thickened the front so I can install fasteners. I found the cubby too small for storing things, but I needed a spot for my GMRS radio…
Print approx. €4.88–€5.96 excl. taxPreliminary estimate for one variant
Mouunt can be attached with double side tape. Additional parts needed: 1x M3x25 screw 1x M3 nut
Print approx. €1.02–€1.24 excl. taxPreliminary estimate for one variant
This is a wall mounting plate for Raspberry Pis. I needed a version that would allow passive cooling, protect from dust and look cool. This model can be easily printed in PETG or PLA with 0.3mm layers. There is enough room to take the…
Print approx. €2.24–€2.74 excl. taxPreliminary estimate for PETGSource material: PET
Galerieleisten-Montage-Nippel passend für 4er-Schrauben und klassische Aluminium-Galerieleisten. Drucken mit PETG oder Nylon, PLA könnte zu brüchig sein. Befestigen mit 6x35er Dübeln und 4x40er Senkkopf Schrauben - abhängig von der…
Print approx. €0.85–€1.04 excl. taxPreliminary estimate for PETGSource material: PET
~*Assembly info is down toward the bottom*~ Background: A couple years ago I wanted to start having LAN parties with my retro PCs, and as I had recently built my home network, I came up with an idea for a self-contained LAN party using a…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for one variant
i printed it from plas with the middle layers (mounting part) 100% infil and support on base plate.
Print approx. €2.88–€3.51 excl. taxPreliminary estimate for one variant
Have you lost one of your front license plate mount brackets on your Tesla? Well, I did, so I designed this replacement part so that I could put the front license plate back on. I tested it, and it worked well, so I am sharing this to…
Print approx. €0.46–€0.57 excl. taxPreliminary estimate for one variant
I am venting my printer directly outside, so I did not want the charcoal filter impeding airflow. This plate holds the 60mm fan alone (you need to use your own screws) I then have another attachment that allows for a 2" flexible tube to…
Print approx. €1.08–€1.31 excl. taxPreliminary estimate for PETGSource material: PET
This works with Merten EU sockets and should also work with Busch Jäger. I used two existing models to get me started (see linked model for the remix source). We have the USB type sockets but with a USB power brick the normal sockets…
Print approx. €1.68–€2.05 excl. taxPreliminary estimate for one variant
Easy to print. I've printed with 0,2mm resolution for beauty but I think 0,3mm is also fine. Horizontal one is 2 part print. Camera in this case is:…
Print approx. €1.30–€1.59 excl. taxPreliminary estimate for one variant
Small nozzles for mounting new 50mm IKEA Paragraf spare wheels on old office chairs. The Paragraf spare wheel shafts are now 10mm instead of 11mm diam. Using these very small nozzles, it was possible to mount new spare wheels on old chairs.
Print approx. €0.28–€0.34 excl. taxPreliminary estimate for PETGSource material: PET
I'm in the process of adding LED canopy lights to my upper deck. Since this is my upper deck, I needed to design holders for electrical conduit pipe that I will string the lights from. I created and printed several models to accomplish…
Print approx. €0.38–€0.46 excl. taxPreliminary estimate for PETGSource material: PET
I wanted to attach a filament bag to the side of my printer enclosure to tidy away all the waste filament. So I adapted the peg and created a way of attaching the peg to the side of the enclosure. You will also need: 1xM3 Nut 1x M3x8mm…
Print approx. €0.50–€0.61 excl. taxPreliminary estimate for PETGSource material: PET
Remixed by 3DFW: This is a remix of ChickenMyBobbers’ clever Alpaka HUB mount replica. I made some small adjustments and uploaded it here on Printables to make it more accessible to others not using MakerWorld. Full credit to the original…
Print approx. €0.20–€0.25 excl. taxPreliminary estimate for one variant
![Front license plate mounting bracket (Tesla Model 3/Y) [REPLACEMENT PART]](https://media.printables.com/media/prints/656120/images/5171796_52365c17-0ebb-43f2-9e4d-0ab3ea8ec011_789faa19-74ad-459b-8631-3c1410f6bb78/img_1200.jpeg)
