Liczymy pasujące modele…
UPDATE: The "remix_drip_bracket_7.2" version (shown in blue) fits better and centers the build plate over the resin vat better. I will remove the earlier version to prevent any issue of downloading the wrong file (earlier version shown in…
Wydruk około 4,84 €–5,91 € nettoWstępna wycena jednego wariantu
12/8/2023 - Added a version without the loop on top of the handle. I remixed this handle to fit my Anycubic Photon Mono X 6Ks, by adding a hanging loop. I also fixed the screw holes by adding more material under the screw heads. I also…
Wydruk około 4,68 €–5,72 € nettoWstępna wycena jednego wariantu
V2 available here: Digital Caliper Holder V2 I liked the original caliper holder found here: http://www.thingiverse.com/thing:640968/#files .... but it needed screw-mounting holes. So I added two counter-bored holes and thickened the side…
From the original creator: This model was inspired by another model https://www.printables.com/model/924041-raspberry-pi-5-case-with-pineberry-hatdrive-bottom , but it's not a remix. The case was designed completely from scratch. The case…
REMIX Version 2.0: Added a lip at the top to give better clearance for soldering at the very top/end of the tool; added 4mm to the back so it can lay flat and sit a bit higher. I discover there is usefulness in laying it down, which is…
Liked the original design, but modified to fit my 2005 Tacoma Prerunner with a 5 speed manual. I added length to the bottom, opened up the hole diameter and added 12mm x 1.25 threads. 6/17/2023 - I fixed some slicing issues. It should…
2/15/26 - UPDATE: Added an adapter to go from Creality CR-Touch to BTT MicroProbe, based off of user feedback (untested by myself). This is an adapter to mount a BTT MicroProbe in place of a BLTouch V3.1 (might also work to replace a…
NEW Improved Model Now Available click this link! 11-3-2023 - Fixed PTFE hole. Version 6.1 has the taper taken out and the hole is sized for a better fit and a tubing stop was added. I remixed Valeriy Proklov's model by adding clips so it…
Exhaust flames to fit the Super Mario Kart by P-atix . I also fixed the exhaust part which Cura was not slicing correctly. You might want to scale up by 1 -2%; I had to wrap a short piece of kapton tape to get a snug fit into the exhaust…
A magnetic pet feeding reminder. Requires five 6mm diameter x 3mm magnets to be glued in after printing. Printed in Atomic blue and white PLA. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank you and…
2/12/25 Update - Check out my new Crosman 2100B moderator mount. Print as many baffles as you want; the more baffles, the greater the sound suppression. Make sure to print one endcap. The barrel adapter is designed to be secured with a…
Check out my new version of the REMIX HERE . A Remix of Andrew Godfrey's Soldering Clamp found on Thingiverse - I just made the base wider for more stability and added 4mm to the bottom to raise it slightly. Here is his description:…
I remixed this to provide a bit more area to hold and also made the clearing pin self-contained. After using it, I changed the coring tube to be 2mm bigger in diameter - this is version 1.2. Your printer should be well calibrated as there…
Just a simple FX Airguns Key chain I designed from their logo. I scaled down the stl file to 61.35% to get it to 80mm length. Printed with ATOMIC PETG Filament in grey and blue. If you like my designs and want to send me a tip, you can do…
New Remix - Added cmh's Guide Funnel to the Remixed Ender 3 S1 Pro Filament Runout PTFE attachment - No PTFE tube needed. I remixed Valeriy Proklov's model by adding clips so it stays on - no hardware needed. The top hole for the PTFE…
A modified rear sight to fit the Crosman steel breech using the factory steel sight blade insert and screw. I extended it to the rear to clear the plug on the steel breech, and made it to sit flush on top of the dove tail using a printed…
I liked the Moderator/Muzzle break from Dan , but the threads would snap off anytime I would pump my Crosman 2100B air rifle, so instead of just relying on the threaded part to hold a moderator on, I added a shrouded portion to snugly…
An S-360-12 PSU cover with voltmeter, switch and xt60 plugs ; with removable access cover. Uses M3 screws and heat-serts for the cover. Note: I designed this to fit an older voltmeter I had that has the two mounting tabs offset towards…
See the new and improved revised model here. Extended cable clip to work with the Gulfcoast Robotics Z-axis Linear Rail Kit ; this is a little deeper, retaining the cable fully. This was modeled off the original file from Gulfcoast…
A light switch cover plate with a holder for the remote control for a Hunter Ceiling Fan Model No. 59452 . I made this to keep the remote next to the light switch - no more losing the remote control. If you like my designs and want to…
This is a stiffening liner for the current narrow Crosman 13xx/Drifter forend. It completely fills the hollow space between the forend shell, the metal lever, and the air tube. Helps eliminate that toy-like feel when pumping and holding…
This is V2 - Cleaned up a bit, better fillets and rounded edges, and proper countersunk holes for flat-head screws. My original description: I liked the original caliper holder found here: http://www.thingiverse.com/thing:640968/#files…
2/12/25 Update - Check out my new Crosman 2100B moderator mount. I remixed the barrel adapter and added ½"-20 threads to allow the use of any threaded moderator you might have or want to print. The barrel adapter is designed to be secured…
Some simple TPU vibration dampening feet to fit the Anycubic Photon Mono X 6Ks. The resin printer has hard plastic on the base, these fit over those extrusions to act as vibration damping feet. Printed at 4 walls, 1.6mm top & bottom, 20%…
Adjusted to allow cap to fully seat; extended the case to better protect the end of the bolt and bolt pin. This fits very nicely and is compact enough to carry an extra bolt and firing pin. From the original creator: Case to hold an extra…
Since Gulf Coast Robotics is no longer in business, I thought I would share the stl files and instructions for their X, Y, and Z linear rails for the Ender 3 S1 Pro. The linear rail guides, drill template, and the ribbon cable holder are…
Seems the left frame plug on my 2007 Suzuki DR 650 SE kept coming off..... after replacing it a few times, I just left it open - until I got my 3D printer. I went through a couple designs which either were too tight and cracked, or were…
A Frame / Case for the BigTreeTech Pi TFT70 v2.1 display with an attached Raspberry Pi 5. For this project I used a 200mm flat display cable to connect the Pi5 DSI port to the Pi TFT70 display, and a right-angle USB-C adapter . Hardware:…
I simple key chain I made for my LittleGuy Teardrop trailer. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank you and enjoy the models I create.
I took the idea from WWTech to make a holder to clip to the AC vents on my truck to help cool Chap Stick or other small items during hot summer days. I used the Car Vent Clips from TVm and made them a bit longer to add a screw hole, this…
I really liked the original Adafruit Heat Set Insert Press, but I wanted to use my Weller WLIR6012A soldering iron and a spare MGN 12-H linear rail I had. There are also some great remix parts from the Adafruit design, so I incorporated…
A simple and minimal filament spool winder that is fairly quick to print and easy to store. I liked all the fancy spool winders on Printables but I didn't want to spend so much time and effort on something I would use infrequently, so I…
Two versions, one uses 2 screws to mount like the original. The second version uses 3 screws to mount to the motor. The CRTouch fits in the original location with this fan duct mounted. From the original designer: "My take on the 5015 fan…
I made this primarily for my RAM GPS mount; When attached to my motorcycle, the vibration would always cause my Garmin GPS to shut off after a few minutes of riding. With this installed, my GPS stays on during my rides (both on &…
A modified Kossel Mini effector for E3D-v6 hotend with 40mm spacing between Traxxas rod ends to mount a BlTouch Z-probe. You need to print the clamp and the appropriate BlTouch spacer to get the correct distance above the nozzle. I…
The easiest and best way to mount an accelerometer to your E3D REVO hotend. Designed to mount a KUSBA or standard ADXL345 Accelerometer board to your E3D REVO hotend. There are two models: 1) Standard M3x12 screws and M3 nuts . 2) M3…
I am not able to find non-ethanol gasoline in California so I decided to remove the ethanol from gas station gasoline myself; so I needed to mark my fuel cans that contain non-ethanol gasoline. Printed in Atomic PLA with supports. There…
This is a side cover grommet for the 2003 - 2017 Honda CRF 150 & 230 dirtbikes. I made this for my 2005 CRF 230 and it looks like my 2006 CRF 150 uses the same grommet for the side covers. This may fit other motorcycles that use the Honda…
Another simple FX Airguns USA Key chain I designed from their logo. Printed with ATOMIC PLA Filament in silver and black. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank you and enjoy the models I…
KUSBA V2 USB Accelerometer STL File for Klipper- I downloaded the CAD file and converted it to a STL file so that I can design my own custom mount for my Delta Kossel printer. Hole diameter: 3.4mm Hole spacing: 23.5mm If you like my…
UPDATED - New version 2.1 with no wobble. Requires one 1x- M3 heat insert. and one M3 x 10 screw. This new version only rotates and does NOT tilt, and consists of the first two files/parts. Files with a 1.0 or 1.1 in the file name are the…
A simple hygrometer mount / holder for my filament spools - fits 50mm diameter center holes. Printed in Atomic PLA. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank you and enjoy the models I create.
A BTT Pad7 accelerometer mount for a Delta E3D V6 effector. I am using a simple effector on my Delta printer with 40mm spacing between the delta-arms. I switched to Klipper and am using the BigTree Tech Pad7 , which comes with their own…
Added ribs on the side plate for stiffness.
I designed this Optical End Stop Switch mount & carriage flag to fit my 2020 delta printer. I also made a cover to fit over the switch to help prevent stray light affecting the sensor. The printer started as a FolgerTech Kossel, which I…
Just a simple steering lock protector cap so that mud does not go in it. I added a loop so that a tether can be added to prevent loss. Printed in TPU. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank…
I remixed the heater case for use in my FDM printer enclosure; I added a loop to hang it from a 12mm carbon fiber tube. I also modified it to use 4mm OD x 4mm M3 heat inserts. The back cover was modified with a built-in temperature probe…
Modified base and roller for various spools. Supports 42mm-width and larger 77mm-width spools. Roller part 33mm width. This accommodates narrow spools better than the original model as well as the wide Atomic Filament spools. Recommended…
Knife sharpener for DMT Mini Diamond Whetstone 70 X 25mm Model is split for easing, no-supports printing. I attached the “clamp” stl to the “stone_holder” stl using 1.75 filament and super glue (CA). I did have to clean the holes with a…
Dust Boots for GCI Outdoor Freestyle Rocker Camp Chair; to keep dust and dirt out of the spring mechanism. Print in TPU It might help to unscrew the top yellow part of the spring housing and insert it into the dust boot, then attach and…
Anti-vibration inserts for the base of the new Anycubic Wash & Cure 3. These are designed to be printed in TPU or another soft, flexible material. These just press into the four corners of the base, so make sure you print four of these.…
A part cooling fan mount and nozzle for the 713Maker ball cup effector plate using a 3010 blower. I am rebuilding my old MakerLibre 1515 Mini Kossel and upgrading it along the way. I decided to go with the SeeMeCNC ball-joint effector…
A top mounted belt tensioner for a FolgerTech Delta Printer. This may fit other 2020 framed Delta printers too. This allows for about 7mm of adjustment travel, and raises the idler pulley about 15mm higher. NOTE : You will likely need…
I elongated the mounting holes and added a recess for the screw head and a 9mm OD washer. This is designed to fit the Ender 3 - Ultra Flat Cast Aluminum Bed Plate from Precise Printer Parts using the Gulfcoast Robotics silicone bed…
I was inspired by vintage Iron Work I-Beam construction to design and make this paper-towel holder. I wanted a paper towel holder for my workshop, but didn't see anything I liked; After seeing an old photo of a skyscraper construction, I…
These are build plate guides for the Precise Printer Parts Ultra Flat Cast Aluminum Bed made for the Ender 3. I used this bed on my Ender3 S1 Pro with a Gulfcoast Robitics 3-Point Y-carriage plate . These simply provide a backstop for the…
REVISED - Extended cable clip to work with the Gulfcoast Robotics Z-axis Linear Rail Kit ; this is a little deeper, retaining the cable fully. This was modeled off the original file from Gulfcoast Robotics, and fits the Z-gantry…
NOT TESTED A quick and easy way to add a BlTouch Z-probe to the Kossel Mini effector for E3D-v6 hotend with 40mm spacing between Traxxas rod ends. You need to print the modified clamp and the appropriate BlTouch spacer to get the correct…
Reduced the hole to fit the 5mm diameter shaft of the Sprite extruder. I recommend printing in TPU and scaling the X and Y to get a snug fit. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank you and…
An AT24C256 I2C EEPROM Memory Module mount for 2020 extrusions. I am using this for a BTT SKR 1.4 board on my custom built delta printer. This lightly clamps the EEPROM module and has open sides for airflow, although I don't know if these…
A simple extruder mount to fit a NEMA 17 motor I use with an E3D Titan extruder on my FolgerTech 2020 Kossel / Delta printer. Hardware Needed: 2 ea. M3 x 12mm screws 2 ea. M3 nylock nuts 2 ea. M4 x 12mm screws 2 ea. M4 x 9mm flat washers…
This is a magnetic mounted z-probe using a mechanical end-stop switch. I am rebuilding my old MakerLibre 1515 Mini Kossel and upgrading it along the way. I decided to go with the SeeMeCNC ball-joint effector arms and their molded platform…
Replacement caps for an aluminum camp table legs. I bought this folding camp table from Big 5 several years ago and have lost two of the end caps on the table legs. This may fit other camp tables as well. The original grey caps are also…
A small E3D V6 Vise for Assembly or Hot-Tightening the Nozzle. Hardware required: 2 ea. M3 x 35 screws 2 ea. M3 nuts 2 ea, M3 washers I added aluminum duct tape to the base for some heat resistance since my main use for this is to…
This model is a scan of a brass CLOW 850 desktop fire hydrant - these were given away as gifts by sales reps.
I got the inspiration from AFGator58 , but I wanted to mount everything in the base of the Ender 3 S1 Pro. So I found some designs, modified them, and got everything working correctly. This is a good guide that walks you through the…
I added clearance to allow the use of M4 T-nuts. I recommend printing in the orientation the STL files are in, with tree supports (on build plate only) and a brim. I used the following print settings: 0.4 nozzle 0.2 layer height 5 walls 6…
I like my BRAUN BC12W alarm clock but it is a pain to adjust the time or alarm on it. So I made a small tool to make adjusting it much easier. If you like my designs and want to send me a tip, you can do so via PayPal ….. Thank you and…
To wszystkie aktualnie dostępne wyniki.
