1532 modeli
NOTE Check out the improved version of the model at https://www.printables.com/model/574794 ! I like to stress-test prints that I don't intend to “keep forever.” I used organic supports for the two smaller pieces and brim on the elbow.…
Wydruk około 1,03 €–1,26 € nettoWstępna wycena jednego wariantu
Use ASA,ABS, PA6 , print with support easy installation with direct taping screws 2.5mm diameter and 3.5mm screws or epoxy glue
Wydruk około 4,45 €–5,44 € nettoWstępna wycena jednego wariantu
Be careful, you need to change the needles size. Update: the needles size: In green: 22mm (4x) In yellow: 27mm (1x) In orange: 32mm (4x) In red: 37mm (1x)
Wydruk około 3,41 €–4,17 € nettoWstępna wycena jednego wariantu
Neues Gehäuse für einen Garagentoröffner von Hörmann HSE-868 Zur Montage benötigt Ihr noch zwei Schrauben M2x8mm mit Mutter und den Ring zur Befestigung
Wydruk około 0,99 €–1,22 € nettoWstępna wycena jednego wariantu
Simple remix of the folding razor blade cutter except there are some notches in place for 45 or 68 deg. cutting of filament. This supports both 1.75mm and 2.85mm filament in 45 degrees. There is only a 1.75mm hole for the 68 degree angle…
Wydruk około 1,77 €–2,17 € nettoWstępna wycena jednego wariantu
I noticed my spools aren't centered with the original design so I made a adapter that should go over the original nut. Print instructions lay flat on the large side. Printed them in PLA 2 perimeters 10% rectilinear infill worked for me.
Wydruk około 1,49 €–1,82 € nettoWstępna wycena jednego wariantu
A bunch of people tend to replace the milk frother of the Dedica. Installing a completely new one is quite a drag, so the “lazy” method is to simply remove the outer part. This leaves people with the problem that the inner frother, which…
Wydruk około 0,67 €–0,82 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Replacement parts for SpeedPro
Wydruk około 0,22 €–0,27 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A replacement axle for the Playmobil® Off-Road SUV (6889). Rotate by 90° to print in horizontal orientation, use support! Use sandpaper to grind down if it does not fit 100%. When wheel is sitting in place rotate it a bit until it runs…
Wydruk około 0,39 €–0,47 € nettoWstępna wycena jednego wariantu
Oil filters are only supposed to be hand tightened, so a PLA tool should be strong enough and you shouldn't need a ½" socket wrench. The main purpose of this tool is to keep the oil that remains above the filter from running down your arm…
Wydruk około 3,44 €–4,20 € nettoWstępna wycena jednego wariantu
Remote control case. Two versions, one with buttons. The other version only has holes. The case is designed to prevent accidental button presses in your pocket. perimeters: 4 layers: 0.2 I look forward to seeing photos of your prints. :-)
Wydruk około 1,55 €–1,89 € nettoWstępna wycena jednego wariantu
A little support is necessary, even if the pot and feet are printed separately. However, both parts must be glued together. A model has also been added where everything is in one piece, support is required here, too.
Wydruk około 0,30 €–0,37 € nettoWstępna wycena jednego wariantu
Replacement of the plastic insert into rail holding the basket. That prevents the basket-holding rail from leaving the guiding wheels. It gets easily broken over time and is almost impossible to get hold of replacement. Recommend printing…
Wydruk około 0,23 €–0,28 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Simple wall mount for a DHT22 / AM3202 type temperature and humidity sensor. Sensor gets mounted with a single M2 - M3 screw and nut while the switchplate gets screwed into the wall using 4 tiny wood screws around M3. The hole this mounts…
Wydruk około 1,47 €–1,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Retrofit of window regulator 6205-25-016821P, used for WV / Audi. Printed mine in PTEG with supports, although the supports can be tricky to remove inside the small gap. Clips easily onto frame and was easy to mount correct. Included the…
Wydruk około 0,70 €–0,86 € nettoWstępna wycena dla PETGMateriał u źródła: PET
DeLonghi Dedica Tool Holder (EC680/EC685) It's covering up the cup tray and make storage space for your coffee essentials. The recess are 52 mm in diameter Tray is for 52 mm mesh disk Printing: Infill 15% geroid layer height 0.3 mm ( to…
Wydruk około 3,80 €–4,65 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Portafilter Tool Holder 51mm It's making your space well organized and clean The holder is for 51 mm portafilter, tape groove (20mm x 30mm, deep 0.2 mm) It is attached to coffee machine (my DeLonghi Dedica EC680) with double sided tape If…
Wydruk około 1,18 €–1,44 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Pour raccorder un embout d'aspiration Festool au gabarit de perçage Wolfcraft 4686 https://www.wolfcraft.com/products/wolfcraft/fr/EUR/Bestellvarianten/Bestellvariante-extern/Guide-de-perçage-mobile/p/P_4686 Inclut les ergots de blocage…
Wydruk około 1,94 €–2,37 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Protective storage case for PGA168 (Socket 1, Socket 2, and Socket 3) CPUs. The case holds a single CPU and snaps closed without screws. The top and bottom have openings, so the model name and other markings can be read without opening…
Wydruk około 1,34 €–1,63 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Více informací: HomeAssistant/SHT-21_Light_Sensor_168 at main · HonzaRuzicka/HomeAssistant (github.com)
Wydruk około 3,27 €–4,00 € nettoWstępna wycena jednego wariantu
I love Prusa signature color orange, black and gray. Inspired by these colors, I designed a Prusa-style mechanical keyboard. I also shared the Arduino code so that if you had a 3D printer, you could easily make a mechanical keyboard. All…
You can buy these from me here! Consider supporting us on Patreon! These are battery holders that can hold (2) 18650/(4) 18350, (2) 21700, (2) 26650, and (2) 26800. I print these out of PETG for the toughness. My builds use a 0.6mm nozzle…
Please check out the assembly tutorial for this project: Update 10/31/2022: Added ISO layout plate version. This keyboard is a revision of a 3D printed Keyboard originally designed my Thingiverse user Fumbucker:…
3D scan of the Venus of Willendorf optimized for 3D printing. Found in 1908 at the site Willendorf II, the object appeared in an archaeological layer datable to 29,500 BP. Measuring 11 cm, the figurine – made of oolithic limestone –…
Allows you to use Makita DHS680 on makita guide rails.
Was absolutely stunned by @Druz320 Canoe inspired SMOLBOAT case. I had to have it...but it was for ortho keyboards, too large to print, and I wanted to use my teensy mount as well as other things I learned from my previous keyboards.…
This model is compatible with the lego system.
After a few interations this model did well during testing. Especially when using only one hand for tampering, the portafilter is not stable when pressing down, so a solution must be found. For my portafilter the fit is quite snug. If you…
VW Bus Pickup Year 1968 Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 - 210 Filament material: PLA
Dimensions: 60.5mm x 47mm For multiple colors: 0.00mm - 2.00mm (green) 2.20mm - 3.00mm (yellow)
This model is compatible with the lego system.
Minimum settings for fastest print !Very fragile! 0.3 layer height 2 walls 2 top&bottom layers 10%infill (i used Cross Hatch)
Ground Plane Antenna 868MHz (or for other frequencies like 433MHz or 915MHz) for Meshtastic or anything else i used 1,5mm² (1,4mm diameter) copper wire to find in Europe in the standard NYM cable or AWG 14 or 15 in the US -stretch the…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, consider buying me a coffee , and check out my other models for something else you might like! ********** The cool paracord tensioner that @SD-3D created…
This is a remix of the MiniZ Ford mustang 1967/68 fastback (sportroof) body . I cut out additional clearance for the front and rear wheels in order to allow better steering and suspension travel specifically on the Fully Printed 1:28 Car…
As compact can be IP68 cable extention case. Versions M12 with 3 wires M14 with 4 wires + 3 on top M20 with 4 wires + 4 on top M14 with 5 wires + 4 on top Material Cable glands WAGO 221s PETG TPU M3 screws M3 heated inserts
This model is compatible with the lego system.
This model is compatible with the lego system.
Remix for use with Meshtastic Requires SMA crimp connector, a piece of heat shrink tubing, and RG174 cable or similar diameter. Glue the connector with the crimped cable into the antenna using 5-minute epoxy or another glue .
..:: РУССКИЙ ::.. Приспособление для снятия фаски в ГВЛ (Гипсокартон) для углубления подрозетников. Для использования необходимо прикрутить два трапецевидных лезвия с отверстиями:…
For better seating …. V2.1 Small Clamp has been reinforced
This model is compatible with the lego system.
3d printable pocket hole jig for woodworking, use high infill and thick walls to prevent part from buckling when clamping. You can use 688 Bearings or M8/M10 nuts as the drill guide. If you want to use nuts as drill guides use an High…
Electrical socket box cover for hidden installation (inside box). Size: D=64,5mm PETG, layer size: 0.28mm Infill: 100% Supports: No
The holder is for the “Filter holder”, the 1 and the 2 cup Filter and the “De'Longhi DLSC058 Tamper” but the Plastic Spoon/Tamper also fit. Printed with the Bambu Lab X1 Carbon in 0.16mm with 0.4 Nozzle, with supports. Using Extrudr…
A case for the PCA9685 16-Channel Servo Driver board from adafruit and its cheap chinese clones (see note below). The bottom part comes in two versions: a plain standalone version and one with connectors for the fischertechnik…
This model is compatible with the lego system.
This is a wire pass through for 68mm standard holes that best clips onto 3-4mm MDF / HDF walls in the back of shelfs, but should fit into thicker material as well. It does not require supports and is best printed in PETG. I also uploaded…
Bearing Press Tools for 6900, 6902, 6802 Bearings The files marked "Press In" are a remix of bikenerd tools. I just changed the numbering to be on the side so it could be bigger text. The files marked "Press Out" are for pushing the pivot…
See https://www.amazon.com/gp/product/B08CHCG42N/ref=ppx_yo_dt_b_search_asin_image
designed these to fit in the drive drawers for my HPe Blade center. not perfect but they work. they fit a wide variety of HP servers gen8-10. tried to make a version that was easy to remove, but kept the older model in case they really…
DONATE: https://paypal.me/JuanCMedina21?locale.x=en\_US Use customs support (see picture for support placement) Recommend to print with 0.24 Layer height and lower speed for overhangs to avoid using supports. Printed with TPU 1999-2001…
This model is compatible with the lego system.
Adapterplatte für die Installation des Sonoff NSPanel Pro 120 PW auf Standard 68mm Unterputz Installationsdosen mit 60mm Geräteschrauben abstand. Der Adapter funktioniert sowohl für die horizontale wie auch vertikale Montage. Eine leicht…
Kabeldurchführung Lochdurchmesser 68mm Der Kabelkanal ist für einen Lochdurchmesser von 68mm gedacht. Das ist das übliche Maß für Schalter- und Steckdoseneinbau. Für die Durchführung gibt es 4 verschiedene Abdeckungen mit 1 bis 3…
All credits to placebo_design for his beautiful and functional design (thingiverse.com/placebo_design/designs). This is a remix of “51mm Funnel for porta filter Delonghi EC680 series” by “Placebo_design” (thingiverse.com/thing:3471204).…
I liked the design by @Cisco and decided to make an improvement to seal against the bottle to prevent leaks. Screw the bottle on firmly to get a good seal. If you add this to your collection and/or download the model, please click the…
Abmessungen (Changpuak-Berechnung, 868 MHz) Frequenzbereich : 850-885 MHz Wellenlänge : 346 mm Boomlänge : 336 mm (Ø 18 mm) Elemente : 6 (Ø 2 mm, Messingrohr) Gewinn : ~9 dBd Elementlängen & Positionen: Reflektor: 167 mm (Pos. 0 mm)…
Adapted for the MRD068A ESP-32 Screw Terminal adapter. Hole spacing is 60mm. Need to print 2x ESP32-Terminal-DIN-Mount.stl
This model is compatible with the lego system.
My garage door fob broke and couldn't feasibly be glued back together (again) so I made a 3D printed repair. 2024 edit: (Several people have asked me over the years if I also have the back part of case, or the switch. The answer is…
Hi, here comes a small housing for the RFD 868x long range telemetry module from RFDesign. It should also be suitable for the RFD 900. The Dimensions are about 65 mm x 36 mm x 16 mm The heat sink and the screws are flush-mounted. You need…
A simple case for a 16 channel servo motor pcb. I used one from Adafruit for my build. I printed it with 0.2 layer height and a 0.4 nozzle in ASA. But it should print just fine with any other material.
This model is compatible with the lego system.
Print it using a heat resistant material. Orient the print so it is on the side, NOT laying flat on the build plate. Use supports. Use 0.10 mm setting.
Paintball Bullet cal. 68 (17,3mm) Paintball Kugel cal. 68
There are already several models out there; Didn't find one with perfect fit for my DeLonghi model which didn't take forever to print. => On to CAD and made my own. Model number of espresso machine in headline to identify if it fits for…
This model is compatible with the lego system.
This is arduino BME680 breakout board sensor enclosure/casing. Its made so that the circuit and the sensor are separated with the wall, that way the circuit is protected from the moisture. For even better protection some silicone sealant…
This funnel clamps onto the bayonet lock of the portafilter of a DeLonghi Dedica EC685. It prevents loss of coffee during filling and tamping. It is modeled off a third party bottomless portafilter with a slightly looser fit than the…
A simple enclosure kit designed for assembling a straightforward room sensor, enabling you to effortlessly monitor temperature, air quality, and humidity levels within your living space. Perfect for Home Assistant integration. Key…
I had an old, slow laptop that had not been used for years. I repurposed the screen, using an external controller board, designed and printed a case for the controller board and ‘feet’ for the monitor brackets. The controller board is…
Item #: SCP-682 Object Class: Keter SAFETY WARNING: IN CASE OF CONTAINMENT BREACH FROM THE 3D PRINTER BED IMMEDIATELY DEPLOY MTF * DATA EXPUNGED * TO RECONTAIN THE ANOMALY. SCP-682, we all love that hating creature so I decided to…
This is an adapter made to suck dust from my Makita DHS680 circular saw with a shop vacuum. opening is 38mm in diameter. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: low Infill: 25%…
Simple wall mount to hang a FTX Tracer RC Car on the wall. Printed in PLA at a 0.28 layer height with 20% gyroid infill Should be compatible with the HBX 16889 RC Car as it is very similar. Potential for compatibility with other 1/16th RC…
VW 807688/c - VW Center Armrest Repair Latch Clip Ersatzgriff für Armlehne diverser Modelle aus dem VW Konzern (VW Golf IV; Skoda Fabia,...). For printing rotate the two clips 90° to position them flat on printbed. 2020-05-29: New version…
This model is compatible with the lego system.
I've resized the original 1:10 to 1:28 so it would fit on the mini Z chassis, basicly it is layered 4 times on itself with a 0.25-0.5mm offset. Most of the time was waiting for Thinigvers to finish processing my input(up to 5-6 hours) and…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Template / guide for power outlet with 68mm hole
---------------- the parts list and the documentation to get started can be found here the link to the new manuals can be found here https://drive.google.com/drive/folders/1cR-nfubPEXCrr6-0PsUFC_jSHIq18V4U?usp=sharing ---------------…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
I found a nice design by Billd to protect a LCD controller of the type M.NT68676.2A. Unfortunately they are shipping a newer version now (M.NT68676.3) and the menu buttons don't fit anymore. The new model also has a smaller main board,…
4x M3 x 6mm countersunk 4x Threaded Inserts M3 X D5.0 - https://www.aliexpress.com/item/4000232858343.html IP2368 - https://www.aliexpress.com/w/wholesale-ip2368.html BMS - https://www.aliexpress.com/item/32808335825.html (4S 40A Balance)…
This is part of my Long Range Weather Station project : https://hackaday.io/project/191652-long-range-weather-station I wanted to increase range for my 868 MHz lora devices. I followed the link of this "biquad calculator" :…
Hi, here comes a small housing for the RFD 868x long range telemetry module from RFDesign. It should also be suitable for the RFD 900. It´s a Remix of the original “ RFDesign RFD868x housing” It comes with the additional cable outlet for…
You can find the BAHA BUG body here . You do not need to scale it up the 1/18 scale fits as in the pictures. I used 10lb velcro and you need to use it sparingly as it is quite strong. Body: Here Buy me a coffee:…
This model is compatible with the lego system.
I print this gun for my son (Red Dead Redemption lover). This weapon is a functional replica for kid fun. I use my Prusa MK3s+ with 0.4mm nozzle. Print with silver and white PETG, but in my opinium PLA is better. Only at parts :…
Model designed in Autodesk Fusion. Antenna created with Moxgen software. Dan Maguire AC6LA https://www.ac6la.com/moxgen1.html Design under Autodesk Fusion360. Mount for navigation holder. Mount for Ikea Tisken suction cup.
This model is compatible with the lego system.
!! Ihre Größe fehlt? Kurz kommentieren, ich kümmere mich sofort !! Kabeldurchführung (2-teilig, drehbar) Diese Kabeldurchführung ist für ein Loch mit 60, 64, 68, 73, 80mm Durchmesser ausgelegt. Sie besteht aus zwei Teilen: Das innere Teil…
u can use 6803 zz/rs2 this is my model little transformed
Ersatz Gummipuffer Heckklappe am Megane 2 Coupe Cabriolet. Da dieses seid Jahren schon nicht mehr bei Renault verfügbar ist, habe ich selber einen Designend. Die Montage ist etwas unentspannt, da die Aufnahme sehr eng ist. Mit etwas…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Stand for a S&W 686-6. Source: https://a360.co/3io6zte
This is an easily printable bearing (more like a bushing) with the size and shape of a standard 6801 ball bearing. It has two separate pieces that when printed are captured together but can still rotate. This works for a stand-in while…
Remix for Kobra 3 Build Plates with 268mm x250mm with more Honeycombs reducing the Filamentusage by 15%
Now take a look at that thing! Saw it, loved it. Evenso the Creator intended to CNC it out of wood, he offered his design as it should print just fine as well. You can check out his howto blog and also dont forget to leave him a like!…
![#0068 [Remix] Flower Pot Watering Can](https://media.printables.com/media/prints/512078/images/4157852_980007bc-de8b-473f-be22-08de4273be77/rl-20230625-035.jpg)
