957 modeli
This tool set helps you get a perfect finish on your silicone caulking. You'll find the following: straight profiles for corners (5, 7, 8, 10, 12, 14, 16 mm) rounded profiles for taps, fittings, or recessed joints (5 and 15mm) a tool to…
Wydruk około 0,30 €–0,36 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Perfekt für Silikon Fugen glatt zu ziehen. Perfect for pulling silicone joints smooth.
Wydruk około 0,58 €–0,70 € nettoWstępna wycena jednego wariantu
This mould is created to make silicone socks for the Prusa Mini. Silicone Sock V2, Prusa Mini is optimised as much as possible. Instead of the standard approach using long m3 screws, the mould is closed with a simple clamp or vise. What…
Wydruk około 2,49 €–3,04 € nettoWstępna wycena jednego wariantu
1) remove the old silicone 2) clean with, for example, isopropyl alcohol 3) apply silicone and wipe with an 8 mm squeegee in the direction of the slant (so that the silicone gets everywhere without air bubbles) 4) tear off the silicone…
Wydruk około 0,58 €–0,71 € nettoWstępna wycena jednego wariantu
For OpenSCAD you need download threads.scad by Dan Kirshner. https://dkprojects.net/openscad-threads/ https://dkprojects.net/openscad-threads/threads.scad
Wydruk około 0,18 €–0,23 € nettoWstępna wycena jednego wariantu
My TPU-printed rubber feet are a very nice design to quickly create cheap feet for various devices. However sometimes you want the feet to be even softer than possible with TPU. So silicone casting comes in handy: Print this mold to cast…
Wydruk około 0,28 €–0,34 € nettoWstępna wycena jednego wariantu
These molds are for casting heat resistance silicone molds for softbait casting with plastisol injector. Example molds have been done with Bright Baits Red silicone Both molds have air vents to improve casting and centering pins for…
Wydruk około 6,31 €–7,71 € nettoWstępna wycena jednego wariantu
I prepared two file variants. A version without a silicone sock and a version with. There is no difference in size, only text labels are added as modifiers directly in the PrusaSlicer. Feel free to change it as you need.
Wydruk około 0,91 €–1,11 € nettoWstępna wycena jednego wariantu
I needed a very fine tip to reach the bottom of some 5 mm diameter pockets while building https://www.printables.com/model/486656-magic-stargazing-binoculars Being not very handy with threads, I opted to remix an existing cap. Please note…
Wydruk około 0,40 €–0,48 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a quick model I put together when I couldn't cut consistent 10 mm length silicone tubes for the silicone bed mod. Works with the recommended 7 mm OD automotive silicone tubing and the cutting slot is 0.5 mm which works well with…
Wydruk około 0,45 €–0,55 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Created this to hold rolled silicone baking mats.
Wydruk około 3,67 €–4,49 € nettoWstępna wycena jednego wariantu
happy and sad smiley face icone magnet for Fridge
Wydruk około 1,34 €–1,64 € nettoWstępna wycena jednego wariantu
Keyhole Pegboard holder for my wolfcraft silicone gun. The Pegboard-spacing is 45mm. Prints without supports.
Wydruk około 1,49 €–1,82 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Silicone Nozzle Brush (stick) I wanted a way I could hand clean the nozzle when hot on my printer. This works great. I used a silicone finger cot that has a brush. I pull it up over this 3d printed board and now I can brush my hot printer…
Wydruk około 2,51 €–3,07 € nettoWstępna wycena dla PETGMateriał u źródła: PET
No brim or supports required. A set of finishing nozzle tips designed for silicone, caulk, sealants, adhesives, and similar cartridge-based materials. The nozzles screw directly onto standard cartridges and feature integrated finishing…
Designed to fit universally on silicone sealant cartridges with an S15 × 2.5 thread , it is a simple and reusable solution for storing partially used cartridges. Features Helps prevent silicone from curing between uses Universal fit for…
NO software modification are required if you have a K1C Just print, glue up the original silicone brush and screw the bracket in place reusing the 2 carriage screws. Now you can use whatever plate you want. I have included a brush mold…
A compact tool designed to clean caulk and silicone cartridge nozzles after use. The spiral tip helps remove leftover material inside the nozzle, preventing silicone or sealant from hardening and allowing repeated reuse. Simple,…
utile utensile per facilitare la stesura del silicone,si consiglia stampa in TPU
This tool features interchangeable head pieces , allowing you to choose the finish that best suits your project. Two head styles: Chamfer – creates a clean, angled finish Round – produces a smooth, curved joint Each style comes in three…
In Prusaslicer set Vertical sheel perimeter to 5 to get more powerfull tool. Print orientation
I printed mine in PLA, no support and in 0.20 mm
This is an adjustable gantry mounted nozzle parking spot and brush for Vorons (2.4 & Trident) using bambu lab's silicone wiper. New Version! Now made more modular and using high temperature silicone RTV to further improve nozzle heat…
The silicone tube/cartridge/cartouche cap helps silicone is not drying after usage See also the version with protector for cartridge and applicator: https://www.printables.com/model/1135314-protector-for-silicone-cartridgecartouche-applicat
Ich hasse es wenn die kurz benutze Silikon Kartusche beim nächsten Mal ausgetrocknet ist... Somit hier ein Verschluss. Damit es optimal dichtet einfach ein Gummiband vorab auf das Gewinde geben (muss aber nicht sein). Der Verschluss ist…
Newer model here - gantry mounted version including nozzle stop to prevent leakage when parked: https://www.printables.com/model/882364-new-version-adjustable-gantry-mounted-nozzle-seal This is a remix of the great design by FunFunBoy…
Silione finishing tool, set of 2. Get those perfect finish silicone corners. Simple tool set, easy print. print 0.2 layer 25% infill material: any [original are made in silicone], but i´ve been using petg and pla, and it works great - if…
Tool for creating nice corners of silicone (e.g. in the bathroom). One object has a 3, 4, 5 and 6mm radius and the other a 7, 8, 9 and 10mm radius. Enough choice for every job!
Add flexibility to your nozzle cleaner,
What started out as a remix has now been completely overhauled in CAD to require a bit less Y-overtravel and be a bit more robust. If you are here to reprint a specific part, or using parts from other remixes, it may not fit together…
Ergonomic silicone scraper Sometimes I need to replace the silicone around the bathtub, so I used my experience in 3D modeling and created this silicone scraper. The scraper can also be used on the printing plate as a bed scraper !! The…
Useful tools for smoothing sealing lines and caulking lines, which helps save sealant without masking tape when you apply it for sealing work. They are suitable for most types of sealant such as DIY crafts or floor silicone sealant,…
Il SiliconeEdge Scraper è il raschietto pratico e resistente, progettato per rimuovere facilmente il silicone in eccesso da spigoli e angoli. Grazie alla sua punta a V di precisione , elimina il sigillante senza danneggiare le superfici,…
No brim or supports required. Threaded nozzle tips designed for silicone, caulk, sealant, adhesive, and similar standard cartridges. The set includes multiple nozzle variants: Flat tip 45° angled tip The threaded base allows the tips to…
They can be assembled with binder clips to form different sizes of rectangle and different sizes of squares by different combinations for different size molds. Can be stacked to make taller mold.
Printed with PLA. 0.2 layers. 3-4 walls. 30-99% infill. No supports. Top/Bottom pattern: Concentric Prints in 10-15 minutes.
Caulking Gun Nozzle Unblocker / Nettoyeur canule cartouche silicone
This Silicone Tube/Cartridge Cap was born out of necessity when my brother asked for something to keep their silicone and sealant tubes from drying out during their construction project. The cap features rounded edges for a better grip…
Simple replacement/disposable nozzle for silicone sealer tubes
Regular size caulking nozzle (10cm) Remixed from an original design by Lannix 3D https://www.printables.com/model/150759-extended-caulking-nozzle
This is a modified version of motocoder's jig to suit the Sovol SV06, the length of cut silicon tube has been extended to 12mm from the 9mm of original jig to better match the Sovol SV06. Information about the original mod can be found…
Cap for silicone cartridges or simlar, with S15x2.5 thread.
I looked into the type of thread that was used for these types of tubes. Everything pointed to a S15x2.5 specification; which is a type of metric buttress thread profile. Seems to fit everything with the same tolerancing that store bought…
Supplement tool for this: https://forum.prusaprinters.org/forum/user-mods-octoprint-enclosures-nozzles/prusa-mini-silicone-bed-leveling-mod/ When levelling hotbed in this mod, you are asked to tighten screws 426°, -32°, 168° or any other…
Summary Silicone/Putty cap for keeping the putty usable for longer period of time. Tolerances are tunned for my Prusa Mini. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament brand: Sunlu Filament color: Silver…
Dial your bed In. Parametric Shims work with your Stock Hard Spacers and Silicone spacers found on AliExpress or Amazon Premade Shims for Stock Factory Spacer and Silicone Spacer if you don't want or need to adjust the size. No worries…
Summary Silicone/Putty cap that I am using to store nozzle and keep the putty usable for longer period of time. Tolerances are tunned for my Prusa Mini. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament brand:…
4 Corner : 90° - 16 mm - 10 mm - Radius 16 mm
Silicone caulking nozzle, ribbed for your pleasure, makes (un)screwing fun!
Helicone variation I created. Super satisfying spinning toy. Pretty easy to print, has no support, infill doesn't matter, 24 spinners
Scraper for removing old silicone. The front cutting angle is 30°, the rear one is 20°. Being made of plastic, the tip may bend, but you can still continue to use it by tilting it further. If you have ideas for a remix or to improve it,…
…Please be sure to hit like & post a make, I'd love to see your prints! MACROS AVAILABLE HERE…! https://github.com/3DPrintDemon/Demon_Klipper_Essentials_Unified/ EDIT: ADDED SILICONE MOUDLE for use with silicone pads, including the one…
OpenSCAD model to simply create a cap with a few measurements. 2025-12-24 update: I've added a replacement nozzle that can be screwed to the tube and a screwable cap to just close the tube without the nozzle. Of course you can buy…
This is a 3d printed mold designed based on https://www.printables.com/model/382059-happy-ditto Ditto should be very soft, so I made a 3d printed mold for Ditto and poured silicone into it. I added a little bit of red coloring(for…
This is a Remix of K1C Silicone Nozzle Cleaner Mod adapted to use 2 A1 or A1 mini nozzle brushes I don't have a K1C. I made this mod to test on a K1, and only applied the suggested changes to printer.cfg (see original model comments) YMMV…
En mi caso he impreso con PA6-CF a 0,08 de altura de capa y 30mms de velocidad, con un relleno de 15%.
Sealant cartridge cap to conserve your opened cartridges. Fits standard cartridges. Beveled flange and corners for a tighter seal and easier grip. Print upside-down due to the bottom bevel (or sink it into the bed when slicing). Works…
Simple, 3D-printable molds that can be used to cast moulage wounds in silicone. Moulage is the art of applying mock injuries for the purpose of medical simulation training. Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament brand:…
The box's internal dimensions are 4in diameter by 2in deep. 4 asymmetrical keys allow you to easily line the mold halves up and create a very positive fit, which prevents shifting in any direction. Use binder clips to hold the halves…
Bambu Lab X1C/P1P Nozzle Wiper with 2mm Silicone sheet. Print the design with higher temperature materials like PETG… ABS, ASA Recommended to print the design laying on the side. Cut 14x17 mm rectangle from 2mm silicon sheet. Insert the…
It is a quickly designed cap for a silicone tube. You may want to scale down .1% for a tighter fit. Update: I was adding a seal with a piece of tape. To improve the design I added a screw mechanism to tighten the tip. I am leaving the…
I developed a mould for silcone sock of nextruder. So far I estimeted the dimensions based on the pictures. The mould is already working. V9 update: - nozzle lenght decreased - open version added (for these version both mould halfs are…
3D-printable molds for silicone casting. Wound packing task trainers are simple educational models that can be used to teach/learn wound packing procedures to stop bleeding. Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament…
My second try on designing a mold for Pokemon. As I look through all Pokemon related models on Printables, I found Gengar very suitable to be made soft and bouncy using silicone. It has two pouring holes (under Gengar's foot), and three…
This is a simple mount for a silicone brush to wipe the K1's nozzle with. It mounts to the rear where the plate is attached. See pictures for details. Reuses the same screws. For the brush, you have two options: --- Option 1: Use a…
This thin nozzle tip fits a 3m marine silicone 3 oz (88ml) tube, but will likely fit other tubes (silicone, grease, other sealants, adhesives, etc.) of similar size or shape. The nozzle tip is quite fine (i.e. small outlet diameter) for…
Have you misplaced your silicone nozzle cap? Maybe you just didn't get it in the package (like in my case)? Well, here you go! It's the perfect length and taper for the nozzle. The threads are modeled so it screws on and off easily! It's…
Silicone Sealant tube nozzle nozzle cleaner cap with FreeCAD (RT) file. I printed with 5 perimeter and with 0.16 layer height from PLA. Update 2023.12.28: WARNING : not printed and not tested… siloplast_v2.FCStd - can be loaded with stock…
After looking for replacement parts for my K1c brush and not finding them for sale, I decided to look if someone had created one, but they all differ in some way from the original, so I decided to replicate the original myself. Printed on…
Simple tool for applying silicone
This silicone sock mold is used to create socks for the Nextruder hotend, which is used on the MK4 and XL. It consists out of 3 parts, and is easily assembled and put in a clamp to keep it closed. The middle part requires some supports,…
A box to hold your prototyping wire spools, making them organized, In sight and not in way. The original design holds 6 wire spools but I also provided STEP files so that anyone can modify it however they like. For the original version,…
This is a jig used to cut 9mm pieces of silicone tube for use with the Silicone Tube bed leveling mod for Prusa MK3 printers. The mod is described very well here: https://github.com/bbbenji/PMSBLM and here:…
Printable parts for creating silicone mold - cast your own design-ish soaps. Including models in step format for simple remixing. You would need: Soap positive (printable, four designs included) Mold base (printable) Mold shell…
This is a remodel of the Flipper Zero case. It uses groove to fit flipper zero with its silicone case and also deeper groove for text so it can be easily inserted and printed. Its print with no supports you gonna need 8 M3x20 screws.
Here is my solution for a silicone caulking tool. I'm rather satisfied with the results in my kitchen, so feel free to try ! Several chamfer sizes are available (I used 6mm). I believe that this shape design makes it easier to succeed in…
[Changelog MK2] 20251103 User @CoreyRogers_489647 reported interference with bed issue. Lightly remix to increase clearance. UNTESTED. ----------------------------------------------------------------------------------------- As suggested…
I improved my previous mold that makes silicone Ditto. https://www.printables.com/model/413425-silicone-dittopokemon-mold Improvements: Combined two small holes that are for pouring and air leaking into one very big hole to allow easy…
I made my own first layer calibration with a bigger center square and horizontal infill and 45 degrees infill for the corner and side squares. This way you can easiely dial in your live z for the center and look at the difference early.…
Print this remixed part in place of “Voron Purgee Wiper bracket.stl”. The wiper has an adhesive backing so it should stick directly to this part. You will print the other files from the original model.…
It bothered me that I didn't have an exact overview of the types of silicone I had in the workshop.
Standard silicone cartridge nozzles are too wasteful for my taste - you have to push out a great volume of material to fill them and get it going out of the nozzle. Also, there's never one around when you need it, because they're…
Hello, i always have trouble to create nice silicone joints and startet to look for some handy tools. I saw some good tools in wood, but they were very expensive (4€ each size). Good we have 3D printers, so i designed some and tested…
After countless tests, I am proud to present the ultimate nozzle wiper design, perfectly tailored for the Anycubic Kobra S1 . This design solves the most common issues: Perfect cleaning thanks to precisely matched dimensions. Eliminates…
Just an interpretation for the ear saver
3D Printed Silicone Caulking Nozzle with Integrated Smoother This nozzle streamlines silicone application, combining dispensing and smoothing into one efficient tool. Designed to fit standard caulking guns. Key Features: 2-in-1…
This model is created to be used as a base to make silicone, plaster, etc. molds. Print 4 pieces to get the base and fasten them with 4 clothespins (then it is recommended to fill the joints in the base with plasticine to avoid leaks).…
This is a mold for an improved silicone sock for the E3D V6 hotend that is harder to come loose during printing. Use with 2-part high temperature silicone. Video on the whole process: High temperature silicone (aff):…
here is my prtouch_v2 config section which works with that cleaner for me: [prtouch_v2] # K1 pr_version: 1 step_base: 2 z_offset: 0 noz_ex_com: 0.05 tilt_corr_dis: 0.03 tri_min_hold: 2000 tri_max_hold: 6000 pres_cnt: 4 pres0_clk_pins:…
A tool to remove silicone and caulk.
This is a series of mixing cups with a spout shape so that you can pour accurately without product dripping down the sides. The spout is not too big so it doesn't interfere with complete stirring. I made them for use with 2-part resins,…
To prevent drying out of acrylic or silicone catridges I designed this tool. It has a sealing ring inside. The sealing ring is about 15x10x3 mm German version: Um zu verhindern, dass Silikonkartuschen zu sehr austrocken habe ich diesen…
Prusa XL Silicone Nozzle Wiper. I didn't want to use a metal brush wiper on my brass nozzles, so I made a silicone wiper. I have had this working well on my 5TH XL for a few weeks now. It gives a nice squeegee wipe clean. Parts you will…
you have to print 4 pieces of this model. for this there must be either 2 times each one size or 4 times the same size. setup: take the four parts and put them together like in the picture, now you can secure them with screw clamps or…
ENG: silicone/glue dispenser - caluk gun 4 small screws needed to attach base to the glue tube print with 0.2 resolution no support needed infill min 40% (the more the better) PL: pistolet/wyciskacz do silikonu (dodatkowo potrzebne 3-4…
There are two types of rings in here. One is wider “mens” and the other is narrower “womens”. Both are set to a 20mm inside diameter. Feel free to go into the Fusion360 file and change the diameter to fit your finger. These rings are very…
I am using Tap on my trident which pushes the hot end forward, thus making a rear nozzle scrubber very difficult to use. Clearances are extremely tight. I added a angle to the front of the brush holder to get the brush as close to the bed…
