172 modeli
Modem/Router Shelf Really simple modem shelf. The shelf is glued to the wall with "Pattex Mounting Glue".
Wydruk około 3,70 €–4,52 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This wall mounted bracket is for an AT&T BGW320 Fiber Modem. It allows you to mount your modem on the wall securely. It includes the mount shelf with retaining tabs, a top clip, and an optional power supply mount which clips to the…
As the Cable Fritzbox Modem doesn't come with a built in wall mount, i designed a simple one wich will do the job with ease. no special settings needed
1.3U rack mount for the Motorola MB8611 / MB8600 / MB7621 cable modem, with ventilated shelf and keystone jack. Also has a screw mount hole to mount the modem directly to the modem tray. You must remove the base/stand of the modem in…
Rack mount for the Motorola MB8611 / MB8600 / MB7621 cable modem, with ventilated shelf and keystone jack. Also has a screw mount hole to mount the modem directly to the modem tray. You must remove the base/stand of the modem in order to…
I made this simple set of racks that I use to place my modem/router/Apple TV, etc. The size is 220mm x 160mm They are attached with 10x2mm magnets The “base” model uses 4 magnets (4 at the top) The rest uses 8 magnets (4 at the bottom, 4…
For mini rack like a deskpi, this holds an Arris cable modem.
Use screws from original base to mount modem to brackets once they are on the wall. Use M3 for wall screws, spaced 135 mm center/center. Recommend printing brackets on side for strength with supports (touching base only). Can print…
Print in PETG with front facia on the bed, and with supports - Prusa Slicer Snug is the best for this. Please see the comments section for some important details discussed. The tl;dr is - the stubby leg things that protrude out the bottom…
Spectrum Modem 10" (10 inch) Rack Mount Bracket Should be compatible with the following models: E31N2V1 E31T2V1 E31U2V1 EN2251 ET2251 EU2251 In order for this to fit on my print bed I removed half of the front face of it and created a…
Partially enclosed shelf for a Shaw Fibre+ Gateway modem 2.0 (XB7). Also works for Comcast XFinity TG4482 / Arris. Printed with PETG, 20% infill, no supports needed. Suggest adding a cylinder modifier around the screw holes to strengthen…
Wanted to mount this guy to a board, did not like the goofy stand it came with. This would possibly work with other versions of this model.
Hier liefere ich euch ein Gehäuse für einen einfachen MMDVM Hotspot auf Basis eines Pi Zero’s in Verbindung mit einem Duplex Modem. Achtung, dieses Gehäuse ist nur kompatibel mit den neueren Modem-Platinen ab Version 1.3, da diese Boards…
Wall mount shelf that fits a cable modem "Sagemcom WiFi Hub C2 - F@ST 3890V3 CHWU" The supports below the shelf doubles as convenient points to tie the cables to. The hexagonal holes in the shelf are for ventilation, as the modem has…
Summary I've got a small networking rack, where my router and switch are located. I've also got an NBN HFC modem, (a DOCSIS cable modem), this is produced by Arris for NBN Australia, but their enclosure is used across many different…
Got my Netgear CM2000 Cable Modem, and for some reason it seems Netgear wanted it to look "sexy", which means it has a bunch of weird angles, and takes up a bunch of unnecessary space. I found a mount (…
This wall mounted bracket is for an AT&T BGW320 Fiber Modem. It allows you to mount your modem on the wall securely. It includes the mount shelf with retaining tabs, a top clip, and an optional power supply mount which clips to the…
This is a drop-in replacement enclosure for the original Vigor 167. The modem uses a single PCB, so the swap is quick and straightforward. Handle the PCB with care, there’s a high-voltage section with its own protective cover. make sure…
Rack mount ear for the arris surfboard modems with optional fan and duct. If you need help with printing? Have questions about the designs? Want to keep up with what we're prototyping? Join our discord https://discord.gg/fb4HdDvErF
Just a simple stand for ZTE outdoor modems. Keeps the modem upright on a table or windowsill. Designed for a ZTE MC889A, but I believe the dimensions are the same on models MC7010 and MC889. Do check before printing, though; the…
This bracket allows you to wall mount a Shaw BlueCurve cable internet modem. (Technically the ARRIS Wireless Gateway TG4482) Generically: Technicolor | CommScope CGM4331SHW | TG4482. AKA: Fibre+ Gateway 2.0 (XB7) Mount to the wall with #6…
Small 240x125mm shelf for a router or modem that can be hung on a 19mm wide ledge. You'll need 4x M3 square nuts and 4x M3x8 or 4x M3x10 screws ; grab them from the printer's spare bag if you still have it. Installation: Put the nuts into…
Designed to mount a Hitron CODA-4582 cable modem against any vertical surface using screws. The modem sits snugly on the shelf and can be easily lifted out for maintenance/troubleshooting. Sketchup file included if you want to tinker.
I needed a wall mount for my MetroNet fiber optic modem (Nokia) and couldn't find one. So I fired up Fusion360 and modeled my own. Hopefully, it'll help you. I couldn't find the model number for the Noika modem, but take a look at the…
A cooler for the Arris S34 modem , not sure if it fits anything else. Uses 40mm fans (I used these ) for additional cooling. Should just slide on to the top of the modem when upright. Print using supports. I printed mine in ABS, but other…
This is a small shelf for a router to be fixed to a wall Print Settings Printer Brand: XYZprinting Printer: da Vinci 1.0 Pro 3in1 **Rafts:** Doesn't Matter Supports: Yes **Resolution:** 0,3 mm Infill: 15 to 30 **Filament:** Azure film…
Introduction I've been printing a bunch of ESRack things for my work and home racks and I've always wanted to rackmount these annoying cable boxes. Unfortunately they have a case that's almost exactly 1U high, so the standard ESRack…
Printed on Modified Creality Ender 3 All 3 parts in single stl file Use your slicers “split parts” function to divide them Made with onshape:…
This is a wall support for ZTE mf 289f 4g Modem. There are two holes to connect the SMA antenna adapters to ts9. There is also a large hole to pass the power and network cables. The bracket must be fixed to the wall with two dowels.
I found the original model https://www.printables.com/model/689610-wall-mount-for-hitron-coda56-cable-modemhttps://www.printables.com/model/689610-wall-mount-for-hitron-coda56-cable-modem functional but too flimsy. I added a support beam…
I wanted to mount my LM1200 LTE modem on the wall, but I hate the keyholes it has on the back. They're too small and require small screws. Instead, I made a quick model. This has two holes for screw mounting (and clearance between the…
A wall mount for a ZyXEL modem designed in Fusion 360. This is my first try at making my own model. No supports are needed, printed on Ender 3 v2 with .5mm nozzle and .25mm layer height. Printed in black PLA MAX from Hatchbox. Screw holes…
V ČR osazuje tento modem T-mobile, zejména pro zákazníky mající zájem o připojení pomocí transparentní bridge. U modemu není řešeno uchycení na stěnu, doporučuji umístit větracími otvory ode zdi i když je počítáno s větrací mezerou při…
This design completely replaces the stock enclosure on your CenturyLink C3000Z modem, and allows it to be rack mountable. It is expected to be used in a scenario where you have your own firewall, switch, and access points, and just need…
I'm sure other HDHomeRuns could also be used if the dimmensions of them havenet changed but it was designed around the Connect Quatro that I have. The vertical stand has to be removed from the Netgear CM1200 and the modem helps keep the…
I measured the mounting feet on the modem and made some feet that securely slid in and locked in place, then put it on a random L bracket I found. The antennas should be facing a certain way, so it's not just mounted to the wall at a 90…
TNC modem housing. The design is described here: https://sq8l.pzk.pl/index.php/vp-digi-tani-i-funkcjonalny-sterownik-digipeatera-aprs-wraz-z-modemem-kiss/
This model is a bracket to mount a Commscope (formerly Arris) Touchstone CM8200 Cable Modem to an IKEA Skadis pegboard system. This modem is commonly used by the Australian National Broadband Network (NBN) for Hybrid Fibre Coaxial (HFC)…
The original model didn't fit well with my cm3000 modem, specifically the cable hookups. so rather than just drill a hole like a normal person, I redid the whole darn thing in CAD. Now your modem can gain 0.02 horsepower from all the…
Base para colgar en la pared para routers o modens. Medidas, 19 x 19 x 6 Cm.
For assembly required items: M3x20mm screw x4 M3 nuts x4 M4x15mm screw x2 M4 nuts x2 Support is required only on the base place under the two buttons. It can be left in place and does not need to be removed.
This mount will allow you to attach a Motorola cable modem (models MB8611 / MB8600 / MB7621) horizontally and store in a 10-inch networking rack. Unscrew the base from the modem, lay on its side and attach screws through the side of the…
This model was printed with a .4 nozzle, .2mm layer height, and in PETG.
This is a 2U 10 inch rack mount for assorted Spectrum modems. I don't have an exhaustive list of every model that it will fit, however if you modem has this shaped housing it will likely fit. Printing This model requires a minimum of…
More Informationen Coming Soon. First Version! Material: PLA Nozzle: 0.4 mm Layer height: 0.2 mm Important information for disassembly: There are 2 screws under the 2 rubber feet that go towards the connections. Attention! Do not bend the…
This is a mounting bracket to attach an Arris Touchstone CM8200 Cable Modem used by Australia's NBN network for their HFC network to an IKEA Skadis pegboard. Gives a clean look with a small amount of ventilation at the back. Can be…
The standard Zyxel T-56 modem/router by the Dutch internet provider Odido is poorly designed when you don't want to put it on a table. If you want to mount it to a wall the cables can't be plugged in and/or the power button is…
This stand uses an 80mm usb fan in the bottom and blows through the top. Fan https://www.amazon.com/gp/product/B00G059G86/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
FYI the fit on this isn't great - I noticed recently the measurements have been off for this model as well as others (not sure if it's always been that way or if Arris switched things a bit). Use this new model instead…
I created a stand to mount the Sercomm RHG3006 modem on the wall. Easy to print. I printed it with a layer height of 0.2mm
I wanted to rack-mount my cable modem, but these models are slightly taller than 1U, which requires removing the factory enclosure and retaining only the PCB and rear panel. This replacement case is designed for passive cooling, as my…
It is a very simple design made in TinkerCAD. It has a very very snug fit, so if you're worried about scratching your modem you can increase the width and length of the base by the amount you desire and use it instead. Have not tried…
Mounts to the wall using four #8 screws. There is enough play that you can mount it to the wall and then slip the modem into it. The file labeled print orientation is oriented to print without any supports. I used PETG at a .3mm layer…
I've previously mounted my modems/routers/switches on a bare wall in the basement. This is another simple mount that fits the AT&T U-Verse VDSL Modem. Print 2x mounts and screw into the wall around modem. I printed this in black PLA with…
Unser Haus wurde mit FTTdp (firbre to the distrebution point) ausgestattet. Mein Provider stellte mir ein FTTdp Modem das nun zwichen den Router und dem Anschluß geschaltet werden mußte. Da der Platz an der Wand langsam knapp wurde habe…
Under desk holder for modem Compal CH7465 (Vodafone). Used 2 scewrs with 8mm wide head. 20% infill and No Supports.
Vertical mounting bracket for cisco epc3208 modem. Print with supports enabled in the slicer. I printed PETG nozzle 0.4 layer 0.12 to 0.2 CONCLUSION 💚💚💚If you enjoyed the project please like it. 💚💚💚 Post your makes and let me know how it…
This is a stand that holds a Sercomm DM1000 cable modem vertically. It holds the modem in place using a horizontal pin which fits into one of the mounting holes on the bottom of the modem. No support or infill is required. Pictured print…
A vertical rack which can host a Mac Mini, a Technicolor TC4400, Raspberry Pi 4 and a 120mm fan. Print Settings: 0,15mm no supports needed print without Brim on a Prusa Mini Mac mini stand is inspired by…
A simple mounting bracket for the DrayTek Vigor165 VDSL-Modem. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Yes Supports: Doesn't Matter Resolution: 0.2 Infill: 30% Filament: OVERTURE PLA White (Weiß) Category: Tool…
Instructions 1- Uses the screws (4mm wood screw might work as well) that came with Modem, tighten the screws to the holes on the model and leave some space to allow installing and removing the modem. 2- then use a QUALITY double-sided…
Use this rack mount to clean up your set-up. The Rack is 1U in size and fits 19-inch racks. If the fit is a little too tight simply scale the parts by 1 or 2 % in only the tight direction (do not scale overall or it may no longer fit the…
LTE Indoor Router - Zyxel LTE3301-PLUS The Router has mounting holes on left and right and manufacturer do not sell mounting brackets for it. I wanted to mount it on vertical space - so i designed little brackets for it. You only need to…
Summary Hitron-Clip-STL- Holds a Hitron Cable Modem - I tried 2 methods one was to print the peg attached to the clip, which worked, but I preferred printing the pegs separately and supergluing them on so I could play with fitment and not…
This MB8600 Modem tray allows you to mount this modem in a standard 19" rack. While this fits perfectly into a 1U slot, the modem sticks up slightly higher, so it is recommended to have this placed under a blank or something like a patch…
This Skadis mount is designed to hold the Telekom fiber optic modem using its integrated wall mount. To attach it to the Skadis board, print two T-Clips from the original Skadis clip design that matches your board type.
Telekom Glasfaser Modem 2. I measured the mount and modeled it based off of the wall mount that comes with the modem. There is also a model with a flat bottom. If you print it it should fit fine. Just be careful with the little tabs for…
The Sidecar for Psion is portable PPP modem and linux terminal for RS232 devices powered by a Raspberry Pi Zero. Required: Raspberry Pi Zero Pimoroni Lipo Amigo Pro Pimoroni Lipo Shim for Raspberry Pi Lipo Battery 2200mAh PiRS232 Board…
245mm long shelve optimized for print on 180x180 print bed (
This is the wall mount for a Lite 16 PoE USW-Lite-16-PoE (45W) modem. you probably threw it away with the packaging, here's a replacement
Rackmount for LM1300 LTE bridge using the esrack system
Evime fiber ağ bağlattım ve böle bir raf ihtiyacımız oldu umarım sizin de işinize yarar. Solidworks çizimini de birleştirerek ihtiyacınıza göre değişiklik yapabilirsiniz .Ben Pla malzeme ile bastım. Yatak sıcaklığı 60C Nozul sıcaklığı 230C.
I decided I wanted something a little more flashy for my C64. I designed this case for it that has interchangeable face plates so you could make to your liking. I have included three face plate designs in the files and I have printed and…
Absolutely awesome work from MartinRowan . I wanted to put my fiber optic modem on a sled. Used the provided blank sled .step file and made this sled. I'm including the first iteration I made and the final iteration. Initial: Full sled,…
Discover a functionally designed 3D model specifically crafted to securely hold Telstra Gen 3 Smart Modems. It boasts a small lip that ensures your modem stays in place firmly despite the weight of hanging cables. Creating this model…
This is a mounting bracket for the ARRIS SURFboard SBG6950AC2 16x4 DOCSIS 3.0 Cable Modem. I got mine from Amazon . I printed it with 4 shell layers, and 50% infill. You'll need some sort of drywall anchor if you're mounting it on…
Rack mount for Nokia Fiber Modem, which provides easy access to the connectors, while keeping the LEDs visible as well.
This support allow you to fix your VOO box to wall. Print in HyperPLA. Infill : 25% but can be up to 35% depending material used. Print in 3h with K1 at 300mm/sec.
After experiencing several issues with overheating on my Xfinity XB modems, I found that the airflow to cool the device was lacking. Through trial and error, I made several ad-hoc stands to find the right height to allow for the necessary…
Print 2 of each parts, assemble (it's better to put some glue, but not mandatory), and enjoy ! :) [Last edit] Added a reinforced version of feets for better stability and heat resistance: pied-v1a-h20.stl [/Last edit] Print instructions…
I have ZTE MC801A1 5G Best covarage is at the Window so I made this design
My modem was on the ground and I just want to wallmount it and there was no wallmount holes in the back of modem and I created this model to improve cable management.
Wall and desk mount suitable for Neterbit NWR-940X modem with 0.6mm internal space margin. It is best to print with PLA filament. The screw required for the wall model is 3mm in diameter and 5mm in cross section.
Prints without supports. Fits on the Prusa MK3S bed. Print time is 4h47m with a 0.6 nozzle.
It is a simple device designed to fix the ZTE brand modem by hanging it on the wall and can fit on many printer tables.
This mounting bracket is designed specifically for the Hitron EN2251 cable modem, providing a clean and secure way to mount the device to any flat surface such as a wall, cabinet, or structured media panel. The design holds the modem…
Spectrum ONU (SONU) Modem Half Rack Mount. The Modem is around 46 in height, so it does slightly protrude about 1 mm on top and bottom. This is basically a closed front tray with a site hole for the modem status and drop downs in the…
14mm pipe/stick and pipe clamp are not included. Find or make a clamp that fits your needs, I can not make it for all kinds of pipes. I have added 60mm clamp with 14.5mm holder for 14mm pipe/stick and an extender. Make sure to have very…
The case is a simple rectangular case that is designed to fit my XIDOL K5188 USB modem I bought from Tokopedia. The device seems to share the same dimension with UZ801 or other chinese USB modems. The “Zhihe-series LTE dongles” page from…
DreamPi All In One Box for Dreamcast Pi Modem Adapter Hold all parts and allow having only the modem cable and power cable for a cleaner desk. Allow using the hdmi port if needed. You'll need : Modem splitter - be cautious that there is 2…
I designed this neat little Motorola modem stand with active cooling using a 40mmx10mm Notuca fan. I had a 'need' for this because I lay my modem on its side (vents facing down). I haven't had and issue with it overheating but when I…
Wall mount for fiber modem from Metronet.
Stand to vertically orient a DZS Fiber Modem, specifically made for Model ZNID-GPON-2424A1-NA Rev H. When I switched to a new internet provider, the modem they provided was designed to sit horizontally on a surface, taking up a large…
I really liked the original ESRack system design created by @EvilProphet . I created a customized a module to hold my specific modem. I have it sticking out from flush intentionally so you can see the status lights on top. If you would…
I am using a 10" mini rack and couldn't find something I really liked so i cut the ESRack mounting mechanism off this and slapped it on a standard 10" mini rack mounting plate.
This bracket allows you to secure a Hitron CODA-5610Q cable modem to a wall. This is one of the modems used by Fizz in Quebec. Design features The bottom bracket is in two pieces to save material, and each side (left & right) has a short…
I like vintage computers and I came across a project where you can use a ESP32 as an emulator for an old hayes compatible dial-up modem that can connect to my wifi and to a serial port of my older computers and I can surf the internet…
Custom HMT-1 4G Modem Mount, created using the Original Mount as a reference.
