6586 modeli
I was fed up with the Velcro-mounted window seals made of fabric. Firstly, the Velcro gets loose when the window heats up in the sun, and secondly, it wasn’t easy to mount and was never securely mounted. I use a portable air conditioner…
General information Simple mounting bracket for Nema 17 stepper motor with holes for 4mm screw. Print instructions Layer Hight: 0.2mm Infill: 20% Supports: no Nozzel: 0.4 is recommended
Simple Vase Mode Christmas decoration with traditional mounting hole. Take the mounting wire and cap of an old or broken Christmas ball and insert it in the cylinder. Available for 8mm, 10mm, 12mm and 16mm mounting cylinder. I used 8mm.…
***Updated 11-7-2022 | Now Compatible With 15mm & 22mm Tent Poles | *** Added 22mm ID versions of all clamps to add compatibility with grow tents that utilize 22mm OD support poles. If you need a version of these clamps with a different…
Mounting bracket. Recommended to print with a 0.4 nozzle with a layer height of 0.2 or less! For material, something that's more resistant to heat than PLA is advised. Commenter @jornthree_2921709 recommends PETG or ASA. I've used a PLA…
Slides into an empty honeycomb cell from behind. Fits the “X-Large” size of command strips. Prints without support, obviously.
Simple wall mount for skis and poles Category: Outdoor & Garden
Simple brackets, takes 4 screws. Mounts the switch upside down and leaves some air through for cooling. Updated with V2 for a nicer printing result, without the elephant's foot through the rounded bracket. It's angled now.
Fix all the part like the plan in PDF with M4 x 25mm wood screws, I put mine on 388mm x 290mm x 20mm wood bord.
Made at the request of a Printables community member, these mounts are a traditional mounting bracket with dual offset screw points. These mounts are best used with typical flat bottom soffits. If you have angled soffits or rafter tails,…
This mounting plate results in a very robust mount for the DJI RC remote control, such as those offered for the DJI Mini 3 Pro drone. The mount is tailored to the remote control and intended for outdoor use, especially on bicycles. Note:…
PSU Mounting for LACK Table Enclosure. Simple design that allows the PSU can mount on the upper tbale of the LACK Enclosure. This means it can sit on a desktop without the lower table.
M.2 SSD mounting plate for DELL laptops.
These are some bracket designs for holding a Master Cooler QUBE 500 PC case to the underside of a desk. This is ideal for people like me, who have an already cluttered standing desk and don't like cables reaching to the floor. There are…
Cable Clip for the Multifunction (Small) Arm mounting system Features Fits on the “ arm-small-hex-honeycomb-wall-compatible ” Fits 4.50mm diameter cables
EDIT 03/04/2023 Added f3d and STEP files so these can be remixed. __________________________________________________________________________ Designed a system of parts to create a means of mounting the Hadley to a tripod in a very sturdy…
My goal was to make a mounting bracket for the Raspberry Pi 4 that fastens to an MK3S which would look like an OEM part / accessory for the printer. My Pi 4 has an aluminum Pimoroni heatsink case as I liked the idea of the case being a…
Tablet Holder for the Multifunction (Small) Arm mounting system Features Fits tablet-holder-small-[L, R] Fits a Galaxy Tab A8 Change Log 2025-01-01 Added the Step file as requested by @Ferrugius
Use an M8 bolt to mount your Stream Deck Mini. 2 color changes for the stripe. No support.
When you need to mount curtain rods above a window frame, this template provides a quick way to consistently mark accurate drilling holes. Two holes are available, one at 3” and the other at 4” measured diagonally 45 degrees from the top…
Mounting bracket for the Ubiquiti Unifi Dream Machine (UDM). Print instructions Category: Computer Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Filament: 3DJake PETG Black…
I have finally developed a model for a very popular wall organizer. Now it can be used without drilling holes in the walls. There are two options available: for top\bottom mounting and for side mounting Plate size is about 58x58 mm for…
This is a small weather shield I created for an outdoor temperature/RH/barometric pressure sensor. Prints without supports (upside down). The mounting is designed to fit a common breakout board style used for the BME 280 sensor, though…
Small (100x100mm) shelf with invisible mounting. It will not support heavy loads but it is meant to be used to display prints, like the awesome support free Mando by czfirz ( get it here ). It needs some supports for the clips on the…
Dies ist eine einfache Halterung für alle Arten von Tapes. Für die Montage sind zwei Senklöcher mit einem Durchmesser von ø3.5mm vorgesehen.
Please see my updated version of the Rosahl M-1J1R mounting cover , which simplifies overall assembly, especially the USB-C power supply module can be assembled in advance (or ordered fully assembled!), snap-fits into its compartment and…
I grew tired of constantly repositioning my 125mm sanding discs on my orbital sander to achieve proper centering. Uncentered discs result in imbalance, leading to increased tool vibration, making it challenging to achieve a smooth and…
Halteklammern für Netzteile zur Untertischmontage. Anhand der Skizze können die Bemaßungen in Fusion 360 geändert werden (Breite und Höhe des jeweiligen Netzteiles) und die Konstruktion wird entsprechend angepasst. Bestes Ergebnis mit…
I used wood screws and mounted it directly to the wooden board. Power supply uses similar bracket. Also cables are held up with zip ties using this easy print: https://www.printables.com/model/205265-cable-management-easy-solution
A stealthy way to hide an Air Tag under your bike seat ( modeled to fit the 27.5" Mountain bike Rockrider ST 120 Disc Seat: https://www.decathlon.co.uk/p/27-5-inch-mountain-bike-rockrider-st-120-disc/_/R-p-305496 ). The two pieces clamp…
This case allows you to (manually) adjust the focus of a Trust Trino HD webcam (available for ~€10 on Amazon ) and mount it on a flat surface, rotatable in one or two axes (tilt or pan and tilt). With this case, the webcam becomes quite…
Took the official screwdriver mount by LTT which was originally designed for their own Magnetic Cable Management Power Bar Key solution and adapted it to be mounted on your regular skadis wall. It uses the very easy to use Skadis T-Nut…
Print with supports in PETG. You can forego supports and test your printer's bridging. :) Mounts using a few smaller wood screws.
I wanted a simple holder that would move my webcam up and down with Z axis. I couldn't find one that I liked so I decided to model my own. I used Solidworks 2019 student / maker edition and this came out. I used 3 zip-ties to hold the…
Hi! This is my wood pedalboard mounting bracket for a CIOKS DC7 if you plan to install it under like I did. Hope you enjoy!
Designed this to mount an aftermarket ESC in my 4x4 Rustler (Hobbywing Xerun XR8 SCT in my case, let me know if you try some others so I know which do/n't fit). I printed mine in PETG, but PLA will probably work fine too.
This is a rigid arm designed to mount to the z axis wheels of the Anycubic Kobra Neo. It has a 7mm hole oriented vertically at the end that fits a standard Gopro style camera mounting screw (the type you would use to attach it to a…
Havis console mounting Motorola APX-8500 Mobile Remote Head Mount UPDATED POST size requested per @SeanOConnor_5174100 I modified the 3" deep version to 2.5". I have not printed it, but it should work fine. The 2.5" version is named with…
The default Reolink mount is designed for mounting to a wall with masonry screws or wall anchors. That's fine, but some applications need a clamping surface instead. This is particularly the case if you want to mount it onto a gutter, on…
Best to print with PLA or PETG I made this model to help out a friend in need of smoke detector installation! I borrowed one of the smoke detectors to make this bracket!
These corner pieces are used to attach a canvas to a wall. Because all four corners of the canvas are connected to the wall, the canvas is flattened and no gust of wind can blow it from the wall! Designed for a screw head diameter between…
This improved version of the acoustic foam mounting bracket has been improved by adding in a structural beam to keep the mounting clamp from sagging under the heavier load of wider and denser acoustic foams. In combination with 3M Command…
These mounting feet are for the MMU2S Ikea Drybox (IKEA Samla box with lid 39x28x28 cm / 22l) , so you can attach them to the Ikea LACK table and do not have to screw down directly. The feet are very tight with my two Samla boxes. I have…
For easy power strip mounting while keeping access to all USB ports and power plugs. Modeled in Tinker CAD, I did manage to make the brackets just a bit taller than I needed to. I used a couple rubber dots on the pads of the power strip…
This model allows a mounting of the Kistenberg's TRUCK STORAGE BIN 12 (KTR12) on perforated wall steel plates produced by the Element System. The KTR12 box:…
!This is not a real weapon! Hello, I have a mount for Airsoft AK 47/74 for mounting on a riflescope or collimator. It is suitable if your AK Kalashnikov does not have one from the factory. It is an exact replica. Suitable for cosplay.…
I designed this as I wanted to mount my Neve RNDI to the bottom of a shelf in my studio control room so that it did not take up space on my desk. The design was made to print two of the brackets and put them just inside each rubber foot…
Surface mounting brackets for the Phillips Smartbright LED T8 series battens (~26mm wide body). Use PETG or similar for making the brackets flexible enough for the batten to snap-in No supports needed Increase perimeter count until no…
A simple set of brackets to allow wall mounting of a pneumatic can crusher (such as this one from Amazon: Pneumatic Can Crusher ). The rear bracket has a lip which will snap over the cylinder end cap to hold it in place. The mid-section…
This model allows a mounting of the Kistenberg's TRUCK STORAGE BIN 16 (KTR16) on perforated wall steel plates produced by the Element System. The KTR16 box:…
This shaver has a very curved handle, so slides around easily in the bathroom cabinet. This holder is easy to print (two pieces, no supports), assemble (requires two M3x10 screws, which go straight into the printed part) and mount (I used…
Mounting bracket instead of the original steel bracket (if missing or unsuitable). 3 sizes: 37mm, 47mm, 57mm (total height). Printed with 0.4mm nozzle on MK4 in PETG. I used following settings: 0.2mm layer height 4 perimeters 5 top and 5…
In my workshop, I was using a pegboard-mounted rod to hang my tapes on and wanted something better. I saw and tried "tape dispenser - side mounted" by book (https://www.printables.com/model/514012-tape-dispenser-side-mounted) but found it…
This is a model meant to allow you mount items with Arca Swiss ‘grips’ to your wall, so that you can make better use of the vertical space. Easy to store and grab your tripods and monopods off of this plate. Prints without supports. Has a…
TLDR: 3D Chameleon is a (now) open source 4 filament AMS that can be used with many different printer models. Getting it to work well on an AnkerMake M5 using Orca Slicer (and in a compact space) took quite a bit of tinkering. Bottom…
Update 05/23/2024: Now that Frantisek23 has further perfected his design , I definitely recommend his new solution and basically declare my remix obsolete. Since the EndRib_V1b Mini.stl model is no longer available from him in the course…
The Filament Color System allows you to produce color reference chips for to label your materials. Label Features This bracket lets you use FCS chips to quickly label fillament in dry bins, on the wall or where ever you store them. There…
Pen holder for wall mounting with power strips. Extra space to detach. For 4 pens. We use it to label our annual calendar.Size for original power strips. For loosening from below with needle-nosed pliers, for example.
Simply single-side Vesa 200 to 100 mounting bracket I made for a mounting solution for an Nvidia Shield .
Necklace holder for 11 necklaces intended for wall mounting with adhesive mounting. Printed with MK4S on 0.2mm layers using PLA. I suggest adding a layer modifier for the layers that include the hooks to increase to 100% infill for…
Links for Titan Extruder Kit :…
Needed a mounting bracket for a friends car mobile radio so made in onshape. M4 screws for everything I printed in PetG, Polymake PolyLite. Print it on its face.
I designed an organizer system for the Hoto Flexi Spin Scrubber (QWQJA08) that can mount to either the wall using #10 screws or pegboard mounting screws for a 1/4" pegboard. Overview The system consists of six discreet components that are…
Originally I was dissatisfied with how my X axis camera mount was fairly loose on the motor, while printing some cool motor visualizers I found that Clement's mount for the Hypnotic Extruder Visualizer was considerably more stable. So I…
Yamaha soundbar remote control mounting fixture I wanted to mound my remote to those two aluminium rails on my bed. this is what i came up with. It fits perfect. I also included the Fusion 360 file so you can add your own mounting back.…
Do not hesitate to ask for different lengths if the ones already uploaded do not suit your project! I was looking for a rail to mount a led light strip on, so it would light up the wall, but not blind me. I could not find exactly what I…
These mounting brackets are suitable for 30 cm width LED panels with screw holes on the back. The model has high tolerances for the drilled holes in the ceiling. Mounting is very easy. Push the panel to the ceiling and slide it in place.…
Object/type/model: Citroen C4 grand picasso 2015y. Part: Mounting point of battery holder Description: So citroen greatly design battery holder mounting point as you can destroy it on first unscrewing. But we know how truly save…
I remixed Walletclan3D's excellent storage cubby to reinforce it with ribs for weighted\loading, and thickened the front so I can install fasteners. I found the cubby too small for storing things, but I needed a spot for my GMRS radio…
Mouunt can be attached with double side tape. Additional parts needed: 1x M3x25 screw 1x M3 nut
Description Material: PLA/PETG Layer Height: 0.20 Infill % : 40 Supports: None Print Orientation: Default as modeled
A quick bracket that allows for wall or under desk mounting of the CalDigit Elements TB4 hub. Prints well in PLA or PETG. Plenty string enought given the low weight and stresses on the hub. Print with on the ends with the cavities facing…
i printed it from plas with the middle layers (mounting part) 100% infil and support on base plate.
A simple remix of the steel sheet holder by Waldmops but with letters embossed above the mounting holes.
The mounting plate allows the excellent charger holder for the JOYCUBE Fischer e-bike charger from Wolf Flow/db1337 to be attached to a grid with M3 screws and nuts. Print the mounting plate in STL orientation in 0.2-0.3mm layer height…
I wanted to attach a filament bag to the side of my printer enclosure to tidy away all the waste filament. So I adapted the peg and created a way of attaching the peg to the side of the enclosure. You will also need: 1xM3 Nut 1x M3x8mm…
Remixed by 3DFW: This is a remix of ChickenMyBobbers’ clever Alpaka HUB mount replica. I made some small adjustments and uploaded it here on Printables to make it more accessible to others not using MakerWorld. Full credit to the original…
As a car wrapper, I need my wrap lettering tools on a daily basis. I created the holder for mounting magnets for the hanging insert in a BOSCH L-Boxx / Sortimo LB 238/374. With the magnets, large car films or posters can be aligned, fixed…
Are you looking to mount a Dell Slim Soundbar SB521A to Dell 24in P2419H Monitor ? Well, Dell doesn't have one. Sure, duct tape, rubber bands, and string could work… but do you really want something that trashy in a world full of 3D…
Mounting Bracket for a rather affordable LED Strip by Huemihui I didn't want to spend 37€ on proper light in the shadowy prusa enclosure, so I opted for nice generic diffuse LED stripes. The LED stripes are clicked into the mounting…
Designed for creality 500x500 honeycomb with rubber corners. This version centers the honeycomb within the mechanical axes, it has four unique feet for the Right Front, Left Front, Right Rear, Left Rear. 500x500mm is larger than the…
I designed these mounts to fit the Keyhole mounting system that is usually found behind multiplugs or small systems that can be installed on the wall. This particular design is meant to be used with IKEA's galant desks; the mount fits in…
During a recent production, we noticed the absence of a suitable stand for SDI to HDMI or HDMI to SDI converters that could be securely mounted on production or DSLR camera rigs. I used Blackmagic Design’s BiDirectional SDI/HDMI 3G as a…
The status light is still visible through the hole. Printed in PLA 0.2mm layer height 50% infill No supports needed
Hello, Welcome to my profile, full of models and miniatures :-) I have for you a Shelf 300x80x15 with mounting brackets. It is an absolutely great solution for displaying things. It does not need to be painted, it can also be outdoors.…
This Flagger mobile cradle can be mounted 3 ways ¼"-20 nut insert for tripod style mounts Countersunk holes for bottom or back mounting to a surface Countersunk holes for compatible AMPS style mounting bracket Flagger Mobile units are…
Meine Lampe ist mit einer 4W LED in einem G9 Sockel bestückt. My lamp is equipped with a 4W LED in a G9 base. Halogenleuchtmittel sind nicht geeignet! Halogen bulbs are not suitable!
Z-Axis Mounting System for Raspberry Pi Camera A simple bracket that replaces the top left-hand z-rod holder. This allows you to mount the Raspberry Pi camera at an angle to the print bed, whilst still being attached to the 3D printer.…
To use this mounting frame remove the original case screws from the HDMI switch and replace them with some that are 2mm longer, such that you can attach the mounting frame with the cover to the base. For printing the precise settings…
This model can be printed with really low detailed settings and as fast as you can. Supports may only be needed at the transition. Place them with double-sided tape and fix them with two two centimetre long screw's per block. When they…
Um die LED-Beleuchtung des Gehäuses zu schalten, habe ich Montagematerial für diesen Schalter konstruiert. In die Seitenwand des Gehäuses werden Bohrungen mit einem Durchmesser von 26 mm und 3,5 mm angebracht. Das einfache Schutzgehäuse…
I use a BeagleBone Black to run Octoprint with my Prusa Mini and wanted to reduce clutter and the amount of loose wiring. Mounting it on the bottom surface of my desk was a simple solution. One of the brackets has a cut-out to in order…
Pole-mount type brackets specifically designed to attach the pirate tower add-on to a Noa&Nani Moro Cabin Bed with Pirate hideaway package. The bed seems to have pre-drilled holes for an older version of the tower add-on, which is from a…
EN: The door wreath, which we had attached with decorative ribbon, kept coming loose because the adhesive tapes were slowly coming off due to the pull. As I didn't want to damage the door by stapling it, I came up with this device. It…
Diese Halterung wurde für das schwarze Netzteil des Prusa MK3 entwickelt. Damit kann es außerhalb des Druckergehäuses befestigt werden. Wie die neue Kabelführung aussehen sollte, lässt sich gut aus der mehrsprachigen Anleitung von Prusa…
Im Rahmen des PrintClosure-Projekts , bei dem ein Druckergehäuse gebaut wurde, habe ich diesen Einbaurahmen entwickelt. In den Rahmen kann das digitale Thermometer-Hygrometer eingeklipst werden. Der Ausschnitt hat die Abmessungen 46,5 x…
This mount allows you to attach the led driver directly to the back of the IKEA BESTA shelf (or any other). Included is the fusion360 file (it's a bit messy) to allow for your own modifications. Versions There is a 45deg angled version…
Needed a low-profile brace solution for mounting the OREI 2x2 Matrix Switcher I use for distributing my console signal to my TV and PC. The braces are designed to fit nicely around the ventilation holes on the sides. For mounting…
Bracket to use Syncros accessories with PRO saddles. Every Syncros accessory mounts perfectly and holds strong. Originally it was designed for PRO Stealth saddle, but should fit every other PRO saddle. Printing settings: Filament: PETG,…
Bracket to mount a Netgear GS305 (5-port gigabit, metal housing) in a Hager volta multimedia enclosure on a mounting plate. Ports face up, the switch stays open on all sides for cooling. How it works The switch hangs on two printed hooks…
