1367 modeli
Note: the coned center section design saves print time (prior design required individual deposition points for 12 tiny dots that often failed, but that are eliminated here) and provides the strength needed to eliminate the vertical links…
Wydruk około 1,94 €–2,37 € nettoWstępna wycena jednego wariantu
Print a Hextraction board on your Prusa Mini+! Print two of the A sections and two of the B sections to replace the standard 5-15 and 5-7 plates. Five of the original clips are needed, as well as two of the slightly modified clip included…
Wydruk około 0,24 €–0,29 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Set of wrenches/spanners with the sizes: 6 - 7 8 - 9 10 - 11 12 - 13 14 - 15 16 - 17 18 - 19 20 - 21 Print settings: Layer: 0.25mm Draft or 0.28mm Superdraft Infill: 25% Nozzle: 0.4mm Filament: Esun PLA+ (PETG should work as well)…
Wydruk około 3,84 €–4,70 € nettoWstępna wycena jednego wariantu
This is a print-in-place 608 bearing with 8x 5mm ball-rollers separated with distancers. I made it using ±0.1mm tolerances, as all the other models that I found either were too wobbly due to higher tolerances, or were difficult and…
Wydruk około 0,41 €–0,50 € nettoWstępna wycena jednego wariantu
I love the original fish magnet from kennyd1gital but I don't have the exact magnet size, so I made this remix for 8x3mm magnets. You can stick a maximum of 3 magnets in, but in my opinion 2 are enough :) Please also give a like to…
Wydruk około 0,51 €–0,62 € nettoWstępna wycena jednego wariantu
Wanted to make some baseplates for my kids... used the scad model from https://www.thingiverse.com/thing:615256/files to get the size I wanted… Made the base a little thicker to stand up to the stresses of 2 toddlers(hopefully) Pieces fit…
Wydruk około 11,10 €–13,56 € nettoWstępna wycena jednego wariantu
This is a simple snap case for the Adafruit OLED Graphic Display (SSD1306) (.96") 128x64 character OLED display or any similar .96 display. The design is meant to be small/compact and snap closed. Only the standoffs are exposed. The case…
Wydruk około 0,47 €–0,58 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A parametric LED Matrix diffusor front plate. fullcontrolXYZ based, 100%extrusion, 0 travel, 0 retractions. Extrudes at 0.8mm, which is totally fine for a 0.4nozzle. A bigger nozzle will probably allow much faster print speeds. Prints as…
Wydruk około 0,46 €–0,56 € nettoWstępna wycena jednego wariantu
I printed at 0.2mm. The bottom when printed, which becomes the top, is done with two layers at 45 degrees. I used generic white PLA, but anything that is slightly transparent should do. More of my builds at makies.au
Wydruk około 1,25 €–1,53 € nettoWstępna wycena jednego wariantu
This part is designed to to hold a piece of foam or other material over the driver to tweak the sound signature. Installation: Press the part carefully on the driver assembly, (glue is not necessary). Printed with Creality Ender 3, using…
Wydruk około 0,61 €–0,75 € nettoWstępna wycena jednego wariantu
https://pihrt.com/elektronika/473-matrix-8x8-presypaci-hodiny-s-nastavenim
Wydruk około 0,23 €–0,28 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ložisko z-axis-trapézové matky motorů
Wydruk około 0,39 €–0,48 € nettoWstępna wycena dla PETGMateriał u źródła: PET
M8x1 fitting adaptor for use with professional grease guns - for 8mm linear bushes like LM8UU
Wydruk około 0,39 €–0,48 € nettoWstępna wycena dla PETGMateriał u źródła: PET
In remix section the 12 SD box , or follow this link This model is a minimalist box for 8 sd cards
Wydruk około 0,90 €–1,11 € nettoWstępna wycena jednego wariantu
This is an eyepiece lens cap for an Opticron 8x42 BGA monocular. The rubber cap supplied with this monocular is very easy to knock off or misplace as it sticks out from the body of the monocular and has no retention mechanism; this print…
Wydruk około 0,65 €–0,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Adeept Joystick Module Case This custom 3D-printed case is designed for the Adeept joystick module, providing protection while maintaining full functionality. It securely houses the module, preventing damage while allowing easy access to…
Wydruk około 0,13 €–0,16 € nettoWstępna wycena dla PETGMateriał u źródła: PET
For my home automation devices I made this box that can contain 2 cards with 8 relays each ( model 1 , model 2 ); inside the same box there is room to insert a 16-way I2C type I/O (you can find its box among my other projects), while its…
Wydruk około 1,56 €–1,90 € nettoWstępna wycena jednego wariantu
Původně na objednávku na prstýnky - Originally made to order for rings
Wydruk około 3,78 €–4,62 € nettoWstępna wycena jednego wariantu
ABit Fatal1ty AA8XE motherboard implements the OTES cooling system and uses a duct to draw air from the CPU heatsink through the VRM heatsinks and exhaust out the IO bracket. This duct was missing on my motherboard so I created this rough…
Wydruk około 2,11 €–2,58 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Decorate your music room, rec-room, office, business, walls with your favourite musicians with my Rock-Art series of Fusion360art - combining AI, 3D modelling, 3D printing to kick up the aesthetics with minor investment. See club models…
Wydruk około 1,10 €–1,34 € nettoWstępna wycena jednego wariantu
These are 2-, 4-, 6-, and 8-stack versions of the HSW 211x248 wall panel. Print at 0.28 layer height with 5+ perimeters to avoid infill. There is a one-layer separation between each panel. Import the STEP file to your slicer, split the…
Update 18/01/2025: Fixed an issue with the top right corner where it was slightly wider than others ("piece 3"). it took 1000 downloads on Printables and 7000 downloads on MW and one year for someone to mention this! Perimeter wall pieces…
I was looking for a simple, hands-free way to clean the black soot off the lead screws on my X1C, MK3S and Prusa Mini. To use this cleaner, simply stuff some tissue, paper towel or sponge material in the cavity, douse it in IPA and clip…
Trapezoidal lead screw Nut tr8x8-4 for the Trapezoidal lead screw tr8x8 Print instructions Print it slow, optimal height of layers is 0,15. Thinner layers mean smoother movement.
Remix originally from Thingiverse: 1363148 (I think). Scaled up and bottom chopped off slightly for better printability. Has 2 holes for 8mm round magnets 3mm thick.
8x32 LED Matrix Frame No glue*, tape or screws needed Accessible USB port Wall- or desk-mounted Snap-fit sockets for ESP-WROOM-32, MAX4466 or MAX9814 microphone and DC Power Connector for easy installation Optional socket-less version * I…
BOM Part Qty Image M4 Heatset src 1 src 2 12 M3 Heatset src 1 src 2 8 M4x5mm (BHCS preferred) 7 M4x10mm (BHCS or SHCS) 5 M3x10mm (BHCS preferred) 8 Jonsbo N3 Backplane src 1 (verified) src 2 src 3 src 4 I also designed a 7-drive version…
15.01.2022 update This is my version of iFlag display working with all popular simulation games like iRacing, AC, ACC, Dirt Rally, witch SimHub open source software! For this project you need additional Arduino Nano unweld board, piece of…
This is an old video I made as a quick showcase some time ago and will be replaced with another better one soon: IMPORTANT NOTE Even this LED cube is much much easier to assemble than my previous “ Geodesic(k) RGB LED Spheres ” , it still…
Hace unos años un familiar me pidió una tuerca de Métrica 18 y paso de 2 mm, ya que se le había roto la bomba de achique del barco. Tras buscar tuercas en Solid Works y no encontrar la de Métrica 18 y paso 2 mm, decidí construirla desde…
This is a modified version of this Pixel It case . It was created with the excellent Pixel It project in mind. The case has mounting points and an access port for the D1 mini, a cable path to make free-standing use easier, and optional…
You need Arduino Nano Example link 8x8 Matrix Example link 6x m3 Thread Inserts, outer diameter 4,2 mm. (if you want to use 5mm threads, there as a alternative Glas Part 6x m3x12 Lens Head Screws White Filament for the “Glas” Dark…
8x8 Multiboard Tiles because the Multiboard.IO library is a pain to navigate. Credit to Multiboard.IO for the model
The display module attaches on the front face with four M3x8 screws and nuts. M3x6 screws should also work, but may not get through the M3 nut all the way. I added space for four M6 nuts in the bottom of the holder to add some weight and…
M8 x 20 mm Bolt or screw with 1.25mm thread pitch follow or tip if u like <3 G-workz3D <3
Search the web, and could not find a functional bearing with this dimensions. So I create one in a simple way and for fast print. The bearing has no rolls inside. The inner ring has a tap, so it could not fall out. I printed the bearing…
I am Genuinely surprised how many likes and downloads this model got, it is my most successful model so far thank you everyone I printed mine in Bronze-Colored PLA with 15% infill, brim, and supports everywhere. Be VERY careful when…
Collection of screws (ISO 4017 / DIN 933) including : M8x 6, 8, 10, 12, 14, 16, 20, 22, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the…
LEGO TESLA CYBERTRUCK 8x8
This organizer holds 4 sets of 12 hex bits. 3 rows are .875" deep for extended length bits, and 1 row is .375" deep for shorter bits. Two model versions are available, with and without labels. I chose to fill them with the following bit…
Dübel d6-D8x39 8Stück Ich empfehle PETG und 100% Füllgrad. Der seitlich angebrachte “Flügel” ( Verdrehsicherung ) gehört beim Druck natürlich nach unten. Bei Verwendung von ABS, PC oder Nylon kann es zu Warping beziehungsweise…
This project is a three part LED flag light case with different mounting options. V2 supports a 5V DC power supply (5VPS files) and up to a 5mm thick acrylic plate (V1 up to 3mm). Pictures were taken from the left side of the V1 dual…
Update (--> for Breacher & Battle Axe) --------------------------------------------- Silly Shell with 3x airtight Elite barrels 6x Short Darts / 3x Elite Darts / 18 caliber .50 foam balls Update 30.9.2025: Modified shell, suitable for…
🧶🧶🧶 To make a color pattern, you will of course need automatic filament change . I did not use more than 2 colors (for the pattern itself) For coloring, I select fill and set the maximum Smart fill angle . I specify the needed loops;…
I remix the model from LayersFarm https://www.printables.com/model/308131-bambu-lab-y-splitter-with-pc4-m10-pneumatic-connec/files in order to fit my 8x3mm magnets.
Remix von https://www.thingiverse.com/thing:4599572 Schriftzug auf BMW abgeändert. Erweiterung bzw. Austauschteil für den Original Schieber am Wireless Charger. Passend auch für F3x, F8x und I01 (I3) mit Wireless Charging Ablage. Die…
Features A variety of button caps for square 7x7 / 8x8 / 8.5x8.5mm PCB push button switches Works with any switch with a 2x3mm square mount, either friction-fit or glued in place Choose from various shapes & sizes, or make your own with…
This is an accurate recreation of the Prusa MK3 POM TR8x8 and probably other printers (other ones I tried from thingiverse didn't match the lead pitch). I print them in PLA and use them in a MK2 clone I have lying around, they work…
This model houses a WS2812 8x32 LED matrix, an ESP32 and the necessary cables. I'm using it as a status display for my PV inverter, the ESP runs Pixelix to display the contents. Most printers are too small to print the three parts in one…
There are three ways to print this. As single piece :- Please download STL file but there wont be any movements. Multiple Pieces :- Download 3mf file with Full_dismantled.3mf. BEST QUALITY OUTPUT . Please use the 3mf file for assembly…
I downloaded and printed the sd card holder from "mmurase00". Then I figured out that the print can cause that sd card (micro and general sd as well) could either fall out of the slot or you have so much resistance that you run a high…
- 8x3mm magnets to be glued in - 15% infill used in example - Big Note on this print: The example pictured used a layer modifier to add ironing from 3.5-4.5mm. It's not necessary, but I did not test without it on. If you have never done…
UPDATE: There was an issue in the RC3 version, Prusa fixed this in RC3.1. I changed the gcode and 3mf file here as well to this updated RC3.1 design. This file can be used to print 8x the RC3.1 version at once on your MK3/MK2.5(s). Print…
This is the original Siraya Tech Test 2021 V5. I just used Orca Slicer to arrange in the position for the multi exposure test on my Elegoo Saturn 4 Ultra. And cut the numbers on each test so they match the numbers on the screen of the…
I shoot and home-develop a lot of different film formats, and after releasing a few different reels for lesser used formats (110, APS, disc), I started getting approached by people wanting one of equal quality for the Minox 8x11…
USB Stick Holder 8x Distance between the USB sticks: 15 mm
The nut i used as a replacement for regular brass ones. Works great printed with PET-G, PLA or Resin (the one on photo).
My design for GPU Cable Comb for braided cable extensions for 3mm OD cable extensions there are 3 files 4X2, 8X2, 12X2 for 8 pin PCIE cable. good for 24 pin too (12X2). ***Designed with a 0.4 nuzzle in mind**** printed in PLA+ with 100%…
Collection of screws (ISO 4762 / DIN 912) including : M8x 8, 12, 16, 20, 25, 30, 35, 40, 45, 50 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I would…
I wanted to add an OLED to my custom ergonomic keyboard, but there wasn't a great place on the case. This is a simple solution. Two versions. The original is thicker with a wider bezel. It's easier to print and work with, but a little…
This is a universal server rack ear fitting 20x20mm, 24x24mm, and 28x28mm bolt patterns. I based this off of the Linksys rack ear but made it a bit more universal since my Cisco Switch required a 28x28mm bolt pattern. I also made the 3…
Miniature picture frame (~35 x ~40mm outer dimension) with an integrated stand that works for both portrait and landscape. Area inside the frame fits an 8x10-ratio picture. Picture is held in place by a small ledge. Prints fine without…
Hi, here comes a small housing for the RFD 868x long range telemetry module from RFDesign. It should also be suitable for the RFD 900. The Dimensions are about 65 mm x 36 mm x 16 mm The heat sink and the screws are flush-mounted. You need…
I have 8x3mm magnets instead of 6x3mm magnets which the original thing was designed for so I just enlarged the magnet hole in tinkercad. I used a hole diameter of 8.2mm in the design, and my 8x3mm magnet press fits in perfectly and holds…
Chaned the magnet hole for 8X3 mm mangets. Filter I use: https://www.amazon.com/dp/B0782T7L6P
Updates 11/2025: Added a version for third party tips with 4.0 mm shank size (thin section directly behind the heating element at the front). The original Pine64 short tips come in 3.65 mm shank size, as do many third party options. But…
Hello everyone, Token holder remix for Paleo found on Thingiverse (by Lubi90 April 12, 2021) I have changed the place for the dice so that the dice 18x18x18 can now be stored (e.g. Polish version of Paleo Boardgame have dice in that…
Made this for larger prints and added a few holes to hook into a small nail or photo hanger. Should fit an 8 by 10" photo perfectly if your printer prints to size accurately. You can measure after the first layer goes down if you're…
NOW AVAILABLE NEW VERSION FOR OneBlade QP45xx/46xx NOVĚ K DISPOZICI VERZE PRO OneBlade QP45xx/46xx EN: PHILIPS OneBlade stand The model was designed with an emphasis on simple and fast printing while ensuring sufficient weight and…
This is the standard length version of my 5/8x24 muzzle thread protector. Depending on manufacturer, most 5/8x24 muzzle threads are 0.6" to 0.62" long, this protector is 0.62" long. Prints fine with either 0.2 mm or 0.15 mm layers,…
The Rod Sloth by NeedItMakeIt is very cool, but my printer, the Anycubic Kobra, has a Tr8x4 leadscrew (i.e., 8mm diam, 2mm pitch, 2-start, 4mm lead.) This is a completely remodeled version of the Rod Sloth that fits this type of screw.…
Original: https://www.printables.com/model/217840-axe-magnet I liked the original, just wanted it smaller, so I scaled it down and changed the magnet size to 8x3mm (wxh) Smallest version of the original that could support 8x3mm magnets I…
Small tapes holder for Honeycomb Storage Wall. Designed for tape rolls 15mm wide, and with 38mm internal diameter (e.g., electrical tapes). Attaches to HSW M3 insert with an M3 metric screw (requires also an M3 hex nut). Inspired by…
This is a cover for the Monochrome 1.3" 128x64 OLED graphic display which can be found here: https://www.adafruit.com/product/938 Print Settings Printer: Anet A6 Rafts: No Supports: No Resolution: 0.1 - 0.2 Category: Electronics
88x88 mm Shelf: Needed a larger shelf to hold a few photography light modifiers. Made this thicker, larger, and stronger then the original shelves.
This is a remix of 2 files from Windy and Hidayat . Trapezoidal lead screw Nut tr8x8-4 fit perfectly to the lead screw the Trapezoidal nut Tr8x8 "fit perfect!" had the right spacing. I've just mashed them both together. Holes for the m3…
Print-in-place fordable chessboard / pixel art board box with push in tiles. Board Size: 250.2 x 250 x 33.2 mm 64 Tile slots Tile Size: 29.5 x 29.5 x 5.75 mm Print: 0.2mm Layer Height Attach magnets on the inside to help keep the box closed
Pitch 8, lead 2. I designed this because I haven't find any model that will fit my printer. I am using this and testing for one week and still works good. I printed this in PLA and PETG. I recommend PETG. V4 is a little loose and I think…
Hi, here comes a small housing for the RFD 868x long range telemetry module from RFDesign. It should also be suitable for the RFD 900. It´s a Remix of the original “ RFDesign RFD868x housing” It comes with the additional cable outlet for…
Just a case for a 128x64 0.96 inch OLED I2C/SPI You may want to clean it up a bit, but for me it fits perfectly off from the printer. The OLED Module i use is from AZ Delivery, but they just sell rebranded stuff, so it should be pretty…
I modified the RC3 version to make it even smaller in height, which saves about 1/3 Filament per print. Logos/Texts are also removed for higher printig speeds. Print 2 complete Shields (Headband & Bottom) in under 2 hours! Update I've…
This mounting plate is designed for a 128x64 OLED display prototype board. It was designed to fit the part on Amazon with the ID “B09T6SJBV5”. The Fusion 360 file has been included which should make it easier to work this into an existing…
Da ich nix vergleichbares gefunden habe, habe ich selber einen Rahmen erstellt. Der Rahmen ist schlicht und zeitlos. Bilder können einfach eingelegt werden. Der Clip kann mit zB Tesa Powerstrips an der Wand befestigt und der Rahmen drauf…
This is a 3D reference model of a 128×64 SSD1306 OLED display module, designed to assist with accurate placement and fitting in larger assemblies. The model captures the overall dimensions, mounting holes and pin header position commonly…
Play Fair! Referee cards with the profesional size 80 x 110 mm Thickness 1.5mm Have fun printing
Simple remix with rounded magnets 8*2 (still compatible with original magnets)
Included is a two piece case for an 8x8 WS2812B LED matrix. I use this wired up into an Arduino Uno connected via USB to my PC and controlled with SimHub. Materials Here is the exact 8x8 LED matrix I bought from amazon: 8x8 LED WS2812B…
Introducing the NokBox , a compact dice-storage/rolling-tray solution for my TTRPG players. I wanted to gift my players custom dice boxes with different lid graphics for each person. First I needed a box design with a lid that can serve…
Lego road plate 8x16 brick - from new Lego City. Not 100% accurate to the original but fits. The posted photo - extruder 0.2mm and 0.2mm layer height. I tried to print it upside down to get nice flat top. However the recessed studs with…
This was based on the diffuser at https://www.thingiverse.com/thing:1903744. It has the same internal dimensions (10mm square grid, 9.2mm internal with 0.8mm walls between). I added added a 0.4mm layer to the top, a 0.4mm recess for the…
This should work right off the print bed. And if it does stick together a little, pull on the pieces; they should come apart relatively easily if that is the issue.
This insert was designed for a digital caliper as an addition to the BaBo organizer from Willi Dimensions: 3 x 3 + 5 x 2 (lenght: 8, width: 2-3) ----------------------------------- Update V2: Added some pads where the caliper lays on, so…
I'm making a project that uses these 8x8 RGB LED matricies and I needed a reference model. I couldn't find one so I knocked this one up in OpenScad. Seeing as I couldn't find one here, I figured I'd upload it so anyone can use it as a…
“So, my sadness makes perfect sense…and I do have vague memories of people refusing to breed with me.” - 8x3mm magnets to be glued in - 15% infill used in example -example printed on an MK4 using prusament filaments (PLA) If you’d like to…
Hi, so I had some of these 8x8 LED Matrix panels laying around here and wanted to do something with it. I found the awesome matrix project from blueforcer which is open source. I wanted to use these 8x8 panels from CJMCU. Due to the…
CORE One Nozzle replacement tool remixed with space for two 8x3mm round magnets so it can be stuck to the side of the printer. Versions included for for Prusa and E3D, Sock and No Sock. For detailed information about the Prusa vs E3D…
Created this OLED case for the OLED 128x64 pixel screen. Pretty basic case with a cutout in the back to support the 4 pin header to pass through. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2…
Made for my QIDI X-Plus, should be compatible with X-Max and can be useful also for other printers. There are several STL with different clearance. You can use the STEP file to fit your personal needs. I printed the 0.6mm clearance…
Ender 3 V2 Lead Screw Knob T8x4x2 (8mm, 4 start, 2mm pitch) Designed in FreeCAD. Ender 3 v2, Prusament PLA, 0.4mm nozzle, 0.2mm Layer height.
