Liczymy pasujące modele…
Totem extracted from dead by daylight. The sticks that stick out of the eyes and bones seems very hard to print. Also needs support and maybe cut the bottom off in the slicer so it can stand better and make it way easier to print.…
I couldn't find a model that would let me mount and hide my Disco-on-a-stick and Daylight-on-a-stick LED strips and hide the lights behind a tidy diffuser, so here it is. The provided Step files are designed for a Voron 2.4 350, but I've…
I have a new AD5x printer and found a 24vdc LED JST-XH port on the main board. I also had a couple of Daylight on a Matchstick pcb lights. I designed some slip in mounts to screw to the PCB lights and snap into the side rails of the…
==DE== Dieses 3D-Modell ist eine Prop von Legions Messer aus dem Horror-Spiel 'Dead by Daylight'. Es teilt sich in zwei Teile und nutzt einen Zapfen an der Klinge für die optimale Verbindung. ==EN== This 3D model is a prop replica of…
Dead by daylight generator extracted from the game. Pretty hard to print. Definitely needs support. Category: 3D Printing
Michael Myers model extracted from Dead By Daylight. Needs supports and consider printing with "Print Thin Walls" turned on. His hair seems very hard to print Category: 3D Printing
Dead By Daylight lower light tower generator. Used for most indoor maps with a decent height to the roof. Category: 3D Printing
I took a regular Dead by Daylight hook model and resized it to fit headphones. I also shortened the hook so the headphones don’t lean on the table and sit nicely in place. Assembly: I just used glue for the whole thing, and it holds up…
All the daylight on a matchstick mounts are made to be mounted on the top of the extrusion, making it not so elegant. I made a version that hides inside the voron's body, invisible from the outside. Placed at 45 degree angle so the light…
A simple hook from Dead by Daylight. This is a prototype for a larger model that I'd like to make as a headphone stand. This one can handle earbuds only, try scaling up if you want to. This is my first try at designing a model for 3D…
You should use M3 heat inserts with an height of 3mm heat inserty like these ones: Heat inserts M3x3 OD: 4,6mm
Wanted a mount to put Daylight on a Stick LEDs in my Voron so I whipped these up. They should also work on any 2020 extrusion. *EDIT* I uploaded a one piece version; when the gantry on my 2.4 is at the top of the chamber the bowden tube…
This is a mount for Daylight on a Stick , specifically for 250mm printers. It incorporates the baffle design from Vector3D's Daybreak PCBs and creates a mount that covers the entire PCB. BOM For each Daylight on a Stick, this requires: 14…
After trying all other solutions I could find, most mounts put the lights at a 45 degree angle to the frame. However, with my setup, the printer is next to my desk which causes the light to be in my eyes when I'm printing. This mount…
DaylightDiscoRainbow-Stick-Mounts 2020 Mounts for Daylight/Rainbow/Disco on a stick/XXL/Matchstick that has a nice diffuser and looks prettyish... well, better that PCB's bolted to your extrusions V2 update includes design change to use…
This is a remix of chirpy2605's Daylight on a Matchstick LED strip mounts for the Voron v0.x line of printers. The original uses a snap-in design, whereas this remix uses M3 screws and nuts for a more rigid mounting solution. Installation…
Perfect for any Profile running 1515 extrusions 45 Degree 1515 LED Daylight on a stick V0 Micron+ Clips Requires 2 standard Voron heat inserts and 2 6mm M3 screws per light.
I needed a very low profile diffuser for the Daylight on Matchstick LED pcb, so I made this design in a morning. Print settings filament: PETG white or clear layer height: 0.15 for translucency Post Processing Initial design has a bridge…
This is a mount for the Daylight on a Stick. It works on nearly every t-slot profile with a M3 Hammerhead The wires go in the t-profile-slot. It fits with a 2 pin Dupont connector. I advise isolate the unused open pins. The XXL version is…
Dead By Daylight very low light tower generator. Used ingame for maps and places where there's very low height to the roof. Category: 3D Printing
This is 4x5 single sheet daylight developing tank. it requires 150ml of developer. You can easily load sheet in the dark bag and develop it at the daylight. For fixing and washing i recommend to use a small tray, its amazing to watch the…
This is a shielded LED bar mount for Voron 0.2 and likely 0.1 for the affordable “Daylight on a matchstick v2.1 by RZT”. This has an additional switch. Original design can be found here:…
You should use M3 heat inserts with an height of 3mm heat inserty like these ones: Heat inserts M3x3 OD: 4,6mm
Voron V0 Daylight on an Matckstick 1515 Snap in Mount. Inspired and the bracket stolen from https://www.printables.com/de/model/527141-shielded-mount-for-daylight-led-stick-for-voron0 It fits on the V1.0 by Blamm Matchstick PBC The…
I have downloaded this file, and it did not fit the Siboor led lights I had purchased, Since I printed them on ABS, as it shrinks by around .5% on this long piece it was 2mm too short, so it was remixed with those tolances in mind, and…
Diffuser for Daylight on a Stick to reduce the glare from the LEDs Printed in translucent white PETG Requires 2x M3x12mm Screws when using the original mounts
This includes 2 files: 1: A remix of the Daylight diffuser that @setapart2_252450 made; I added built in support for the screw head pockets, and sunk the hole deeper to make the screws sit flush. 2: After doing this I realized it would…
I designed LED holder for 3030 profile (RatRig V-Core 3.1) The angle in the photo is 65°. 45° degrees is also available, but no photos. M3 heat insert is provided in the angle. I printed it in ASA because of Enclosured. for other side I…
Update: 12/30/2023 - Added an XXL version for those who need it. Simple diffuser for regular size daylight-on-a-stick white leds. I printed in white PETG but use whatever color you want for effect. Mounts with m3 screws through the…
This cover is secured using mounting hardware for the Daylight on a match stick LED. This helps protect from being blinded by the LEDs when looking at print jobs. Update 2025-11-13: Uploaded mounting bracket, I didn't model the Mounting…
I improved a ‘Voron 0.2 shielded LED bar for Daylight on a matchstick v2.1 by RZT’ by @C0co_838112 This is a remix of a version that can be printed on Voron0 bed (you will need to rotate the model by 45dgr) Original Daylight LED Stick:…
This is a Logo of the Horror-Game “Dead by Daylight” using Skulls, created with Hueforge. This Hueforge requires 3 colours and was created with the following swap instructions: Start with Black At layer #9 (0.80mm) swap to Grey At layer…
I bought the 270mm daylight rgb sticks from Siboor . For my 350mm printer. Since i didn't like the small brackets i found online, i created an entire bracket to hold the sticks. They are each held up against the extrusion with 2 M3x8…
A simple snap-in bracket to mount Daylight On A Stick (https://github.com/VoronDesign/Voron-Hardware/tree/master/Daylight) or similar LED strip PCBs to a 3030 extrusion at a 45 degree angle. Requires one “Voron-spec” heat-set insert (OD:…
The original green stand packaged with the Beurer TL30 is a little bit flimsy, this is a sturdier version for your desk or bedside table. It allows usage with the cord attached. Maybe the spacing is a bit too loose for you (see picture…
My Porsche 996 does not turn the headlights on and off automatically when I start it but thanks to a tip on the Pelicanparts forum by “doctorz1026” about using a rubber gasket under the light switch, I instead made a small 3D printable…
BOM: 4x M3 screw - 8mm 2x M3 insert nut 2x M3 T-nut
Dead by Daylight Killer's Logo
a diffusor for daylight XXL LED Bars to avoid beeing blinded by the LEDS while working in front or in the printer.
I got the same led bar from Siboor as the creator but I wanted an even stronger diffusion, total height is 4 mm, adding a photo with clearence on my printer, mileage may vary. If the diffuser doesn't sit flush on the pcb you need to snip…
Please don't forget to give me a Like. :) Replace the tiny LED strip on your SV08 with an LED Daylight Stick (version for Voron 2.4 XXL stick 370mm like this one from aliexpress). The main model is for the right side of the top frame from…
I did not like the 2 individual mounts for these ‘voron daylight on a stick’, made the 2 pieces connect so you can screw the mount in first, then the stick to it, easy, without measuring and lots of failures to mount m right. for sticks…
This is a film darklight dev tank. I'm transferring some models from thingiverse. I made these a while ago, but I can do more work on them. https://www.thingiverse.com/thing:3726422
Snap on bracket redesigned for 2020 extrusions One design for standard 2020 and another specific for 2020 V-Slot extrusions Takes 1 Voron spec heatset per bracket
I want to add light in my flashforge ad5x printer. I found voron ledstrip and this project but I want to add magnet
Hardware 4x M3x8 4x M3 Roll-in nuts or M3 hammer-head t nuts 2x M3x5 2x M3 Heatset Inserts (voron style) Diffuser Thickness The pictures show the 1.4mm diffuser and LEDs running at colors set at 10% brightness. Print samples of each (the…
Parimetrar: 2-3 Layers: Top/Bottom 3 Infill: No Filament: Clear
From the game Dead by Daylight modeled using AI. Came out quite small.
The perk Barbecue and Chili from the videogame Dead By Daylight You can print it with multiple colors if you want to. In that case, you should change filament at: layer 7 (0.12mm layer height) Should be printed at layer height 0.12 You…
The standard Daylight mounts dont work with Clee's Beefy Z Idlers. (BZI) so I made up a quick replacement.
Parametric daylight developing tank for single sheet film. Put the sheet in emulsion-side up, and close the lid in complete darkness. Develop in daylight. Some of the design parameters might be wonky for other sizes than 4x5. Upstream…
This is a minimal led holder for the Voron daylight. I used the following to mount it: 4 m6x12 4 m6 t-nuts 4 m3x10 4 m3 lock nuts Klipper config [output_pin daylight] pin: [Your Pin] pwm: True cycle_time: 0.01 value: 0.1 #10% power on…
This is remix of original model, was made to be able printed on Voron 0.2 with print area 120*120. Model needed to rotate 45 degrees on bed in slicer.
You will need the Jewelry Shoppe tie tack with 10mm pad to glue in the holes on the back of these badges. NO PAINT REQUIRED: I have designed it so you can change the filament to each of the colors. Lemme know in comments what other badges…
Daylight on a stick diffusers for 270mm length *has built in supports Use any 2020 led extrusion mounts
The perk Thanathaphobia from the videogame Dead By Daylight You can print it with multiple colors if you want to. In that case, you should change filament at: layer 7 (0.12mm layer height) Should be printed at layer height 0.12 You should…
Print out 25 Baffles for each stick. BOM 4 - M3x6 SHCS 2 - M3 Heatset Inserts 2 - M3 T-nuts
made a slight adjustment so the matchstick doesnt hit the z tensioners
I made these 1/10 scale KC hilite covers to cover the lights on the Traxxas TRX-4 LED light bar. These are multi material printable. Print in PETG @ .20mm with 15% infill.
The ‘Daylight on a Stick’ (type ‘extra’) sold by https://www.alchemy3d.de has a different distance between the LEDs than the original ‘Daylight on a Stick’. This model is a remix of the baffle from…
Daylight pcb: https://shop.zen3d.eu/daylight-on-a-matchstick build log: forum.zen3d.hu/d/59-m095-micron-g2z
Diffuser for the voron v0 Daylight Disco LED-Strips that can be installed in a voron v0.2. Enables better light distribution in the chamber with a more discreet light. Compatible with the mount pins for the 1515 extrusions.
Check your leds temp, if they get too warm another version will be available soonish
For my printer, (ender 5 pro / zerog mercury 1.1 / hydra bed) the brackets from the voron git for the daylight-on-a-stick leds point the light basically down under the bed. I threw together a quick bracket that mounts the stick on the top…
Loved the original model but needed some more space to use the Daylight on a stick-Mod too. So I removed one “ear”. The file contains a full set of 4 pieces. Nothing special but maybe someone need that extra space too.
simple mount for daylight xxl led bar. suitable for front and rear mount on sovol sv08
The Daylight on a Stick XXL from the Mellow AliExpress store has closer holes (285mm spacing) and connectors. This design is based off the V3 design ( Daylight Stick XXL Carrier V3.stl) with M3 brass inserts. I have moved the holes to the…
💖 Support Me If you like this model and want to use it for commercial purposes, you can support me on Patreon and get a commercial license: https://www.patreon.com/cw/MonsieurPierre Add one of Dead by Daylight's most iconic killers to…
After printing the originals and noticing the hole spacing was way off I moved the screw posts to fit Mellow's 284mm hole spacing for their 370mm length Daylight On A Stick XXL
A totem inspired by the game DBD. Printing without supports. The skulls are printed separately, there is a variant of the skull with cracks. If you like my designs and want to support my work, you can find more information on my Раtrеоn.…
Made for Voron Daylight on a stick XXL (mounted on my RatRig V-Core 4 400) BOM for one led stick supports 2 pieces x M3 threaded insert 2 pieces M3x8 (or M3x6) 2 pieces M6x12 2 pieces M6 T-Nut for 3030 Voron Daylight on a stick support…
The perk Hex: Ruin from the videogame Dead By Daylight You can print it with multiple colors if you want to. In that case, you should change filament at: layer 6 (0.12mm layer height) Should be printet at layer height 0.12 You should…
Mount for the Daylight on a Stick XXL to the SVO8. Bracket mounts in the stock LED location. Use two M3x8 screws to mount bracket to top hat in factory location of SV08 LED Light. One M3x8 with M3 nut to mount XXL to bracket. I connected…
Print diffuser from translucent material. I used Fillamentum translucent ABS. Pretty tight fit. Clips can go under or above whatever mount you are using.
Just a little helper object to hold my phone when doing daytime polar alignment. Previously, I held it by hand and the camera bump made it difficult to keep flat while adjusting the mount. STL is sized for a Pixel 3a XL. Fusion source…
i think u know how to use :)
Daylight on a stick 90 degree mount
My daylight bar came with a switch sitting in the middle (actually that's not a bad idea because I don't have any spare switchable 24v pinout left), so I remixed bjamdesign's model. It can be easily done in the Slicer, but just in case if…
Hello, we needed to create a better and more usable insert for the game. That's why this interesting but simple insert into the game was created. If someone wants to use it commercially, just write and we'll make an agreement. Insert is…
I adopted the design of the voron 0 matchstick holder from "Shielded mount for 'Daylight' LED stick for Voron0" by @C47_3 to fit to “the 100” printer. There is a mount for each side of the upper gantry. They align nicely with the print…
The perk Hex: Plaything from the videogame Dead By Daylight You can print it with multiple colors if you want to. In that case, you should change filament at: layer 7 (0.12mm layer height) Should be printed at layer height 0.12 You should…
Carefully manage your wire so the cover or the toolhead do not break it. Make the original brackets even more simple. Do not need to mount at the bottom, and most importantly, no heat insert!
💖 Support Me If you like this model and want to use it for commercial purposes, you can support me on Patreon and get a commercial license: https://www.patreon.com/cw/MonsieurPierre Bring one of horror gaming's most iconic monsters to…
The daylight on a stick version from Alchemy3d (https://alchemy3d.de/products/daylight-on-a-stick-1?variant=503377434708) has a different hole spacing then the standard version and it's not symmetrical. So I made a version for it.…
The perk Forced Penance from the videogame Dead By Daylight You can print it with multiple colors if you want to. In that case, you should change filament at: layer 7 (0.12mm layer height) Should be printet at layer height 0.12 You should…
Intro This is a Fog Vial, an item set to be released in the asymmetrical horror game Dead By Daylight starting July 29th, 2025. It can be used by survivors to spawn a cloud of disorienting gas, but now you can use it as a little bottle to…
The Daylight Disco on a Stick LEDs (RGBW) by Blamm are great PCB/RGBW LEDs design for lighting a 3D printer's encloser or any cabinet as long as you can provide 5Vs and neopixel signal. I installed them on my Voron 2.4 enclosers. They…
Nozzle used for printing - 0.2 mm Layer height - 0.1 mm Print duration approximately 45 minutes Without supports
The Huntress figure, in a Funko Pop! style. a character from the Dead by daylight universe Let me know what other character to create :)
Betweener that can mount a daylight on a matchstick. Fits in the K1 riser designed by @JoeCooper_466417 Printed in ABS with no supports, 3 top and bottom layers, 15% Infill. Each betweener will need 2 m3 heat inserts and 2 m3x6 screws. I…
An easy to print, simple mount for the Daylight XXL LED strip. The design features space to be able to route cables inside of it as well as blinders so the LEDs don't shine directly into your eyes. It is also designed with extra clearance…
Diffuser for daylight match stick leds. I used these to mount to the 1515 extrusions https://www.printables.com/search/models?ctx=models&q=micron%2B&ordering=popular
a 22.5 deg angle to mount the daylight-on-a-stick led board. uses a m3 pressed inset. two versions for the t-nut side the M5_2 is altered a little to not really need supports
I edited the 100 Daylight Edition for the Space Edition version of The 100 printer.
Just made in orcaslicer with a few attemps (cause I'm stupid).
I needed a diffuser/cover for the lights I purchased for my Voron V0.2. I tried a couple models that I found online but none fit like I wanted, so I just designed my own. I printed using clear petg and it worked perfect. Hopefully these…
Print two times per Daylight Stick. Big hole takes an M6 Screw and t-nut on the other side, small hole takes an M3 Screw with an Nylon Nut on the other end.
I needed something to mount my Disco XXL strips to my RatRig 500mm printer so I whipped up a couple of blocks to mount them to the underside of the enclosure. For each stick, you'll need one standard block and one mirrored block as well…
This collar-style adapter inserts into the LED Light Bar arms and holds a Daylight On A Stick LED bar. Print 2x plugs if you want to hide the opening. Daylight On A Stick reference link
