Liczymy pasujące modele…
Inspired by similar-looking can dispensers, but built from scratch to actually fit cans I use and hold more cans (accommodates around 11-12 standard-size cans). The parts are split to allow printing on a Prusa Mini, with joints hidden as…
This is a Modular and multi-size tape dispenser. I first designed this as a single size (3/4in) non modular dispenser, held together with screws. The comment I got the most was : were are the other sizes? I refined the design, corrected a…
Version 2 Available 💊 Ultimate Weekly Pill Organizer & Dispenser (Gravity Cascade System) 💊 Looking for a smart, functional, and stylish way to manage your daily supplements and medications? This Weekly Pill Organizer features an…
A beverage can dispenser made of strong stackable modules that can hold any amount of a beverage you would like to have on hand. Either in your fridge or elsewhere. I wanted it for my redbull addiction, but I used parametric design so I…
A Custom-Designed Dispenser to fit Pokémon Booster Packs up to x43 packs for the single dispenser & x86 for the double dispenser lid is optional depending on your needs. The Dispenser prevents damage to booter packs, warping & UV…
Perfect dispenser for can´s in the frideg. First in first out, so you always have a coled one :) One dispenser consists out of two parts, there are two center pivot´s for the perfect alignment by glueing together. RedBull 250ml CocaCola…
The 3D modelled Solder Paste and Flux Dispenser is a compact and efficient device, perfect for electronics assembly. Its ergonomic design makes it easy to use, with adjustable dispensing volumes ensuring accurate and consistent results…
Trash bag dispenser Can hold a roll of 35L bags or any roll of bags with 6cm diameter and 15cm height/length 2 screw holes Easier to print bottom chamfer than on the original model Remixed from Augustas Kazlauskas fine Trash bag holder to…
Holds 10 rolls of bags and has screw holes to be wall mounted, or use two sided tape/Command Strips to attach. Bag rolls are about 30mm in diameter and 61mm wide, so this dispenser might work with others. Initially designed without the…
A duck shaped tape dispenser, intended for use with standard scotch tape rolls or an equivalent. The main shaft uses a threaded cap to keep the tape from falling off, and provides an easy way to change the tape when needed. Two different…
Based on the great model by @ KaliM. UPDATED VERSION v3 on December 1st 2024. Changes : Walls are thicker (3 layers) Vertical hole at the front is bigger: easier to guide tablets going in Hole to retrieve tablets is bigger (vertically &…
Wanted a single piece print for the can dispenser, and just placing the parts together in prusaslicer was leaving wall lines in the part where the connectors were, so reworked it in fusion to make each side be a single part with no…
couldn't find a good pop up dispenser for sticky notes (the ones that come zigzag) So designed this simple dispenser. At first I left both sides open but since the top part with the opening weren't connected to the bottom it was very…
Compact Capsule Filler with Credit Card Mixture Dispenser This compact capsule filler is designed to fill 24 capsules of size 00 in one batch using a credit card as a mixture dispenser. The capsule filler is made up of three functional…
I love the can dispenser by @Enigma , but it did not fit my refrigerator. So I created a parametric Fusion 360 model, that could be scaled to different lengths. When using the parametric model, be careful, and change the length in baby,…
I got a new Nespresso machine (Vertuo) for my birthday. I have decided to rint my own dispenser for the pods. I wanted something useful and easy to print. The model comes with 2 parts: Bottom and Cover. Those parts can be fit on a Prusa…
Use suppost as shown in green in the image.
I couldn't find a “key” that had both parts on it, so I sketched this one up
Just a tea dispenser with 70mm x 80mm x 110mm measurements. It prints best with the hollow side up and some support structures for the front side. You can stack them or put them together, since there is a notch that goes into the next…
I have made updated model with lid and viewing ports, check it out: New version I present to you fully parametric boxy things dispenser - originally meant for dishwasher tablets. You can use it of course for anything with boxy shape.…
I created that shooting patch dispenser to replace the standard paper patch dispenser while they get wet and don't work very well after a while. In case the lid is not holding as expected, a small tesafilm strap can be used to secure body…
FA CTU brings a design that matters. This student-designed menstrual product dispenser was adapted for 3D printing to be accessible, easy to produce, and ready to use in schools, offices, and public spaces. The model is based on a design…
Simple Tape Dispenser inspired by Prusament Spool design Very simple dispenser for basic tape. Iťs designed for tape with total radius of about 5 cm, inner radius of about 2.5 cm and width 2 cm. But as you can see, there is some space…
This tape dispenser is a one-piece, foldable design similar to 3M's tape holder, but enclosed. There are two versions for 1in and 2in wide tape rolls.
A simple straw dispenser I made, I used a hexagonal pattern on it to minimize the amount of filament needed (it is still a pretty big print though) and because it looks cool. Print settings 0.4 mm Nozzle 0.15 mm layer height Supports…
Organize 18,10 and 6 mm Tamiya Masking tape dispensers on your Ikea Skadis board. See also my other designs for more ways to Organize your Tamiya tools on the Skadis board.
“Years ago" Inspired by all kind of clever solutions at the time, I designed a dispenser for 330ml cans which printed in only 4 pieces on my BIG 3D printer (~450mm x 450mm x450mm) which rests in piece ;-( Luckily the local brewery decided…
For those of you who place solder paste on a PCB by hand using a solder paste syringe, this tool provides additional control and consistency to the application process. Parts Printed: Syringe Holder [A] Syringe Plunger [B] Knob [C] 1ml…
Artistic and ergonomic tape dispenser designed for office use. Compatible with usual office tapes. New GGvision studio creation.
A simple and effective dispenser for laundry or dishwasher pods. Mounted to the wall with two screws or 3M Command strips. Supports on for the overhang in the mouth of the dispenser. I printed in PLA at 0.3mm Layer height, 2 Perimeters, 3…
I design this model for my girlfriend She wanted a pads dispenser to make more elegant than just letting the box of pad in the bathroom. The cap snap in the box, i have print both of them in PLA I have pretty big hand but the hole is well…
Description This is a heavy tape dispenser, If you have never used one, a heavy tape dispenser allows you to pull tape from it using only one hand while the other is free to hold the thing you want to secure in place. The dispenser is…
I added also an Interlay with a tag. Now everything is well organized in my tool box :-) Many thanks to bomas_ulz for the original model!
Hold your Zeiss Lens Wipes in a 2x2 gridfinity bin.
I started this battery dispenser project with the following design goals: It should enable a FIFO (First-In, First-Out) system It should hold 24 batteries ("value pack" sized) It should have a front-loading slot (at the top) It should be…
Easy to print and Assemble Mason Jar Candy Despenser. Requires: Wide Mouth Canning Jar (Mason Jar) n°2 M5 x 25mm Socket Head Cap Screw n°2 M5 nut n°1 M8 x 60mm Socket Head Cap Screw n°1 self-locking m8 nut (It absolutely needs to be…
This is a little box for storing panty liners. The lid is optional, maybe for a vacation space that gets some dust.
Tennis ball dispenser for small dog tennis balls (~48mm). Printed without supports in PETG. Has 2 integrated countersunk holes for screws to mount to wall.
stackable tea bag dispenser V2 The tea bag dispenser can now be printed completely without support structures. The stacking technique has been further optimized and simplified.
I used organic supports for this and two sided tape on back. 16.2.24 update: Fixed cover.
Modular automatic small animal food dispenser for Mice, Rats, Hamsters, Degu chile... Dispenser has a base to which pipes of different lengths are connected. the length of the pipe determines the size of the tank for food. There are two…
Bin filler and part dispenser for Honeycomb storage system Functionality With this model you can fill up your storage bins easily and fast by just pressing the bins against the front lip of the slider. A spring will bring the slider back…
This standard bathroom cup dispenser works with Dixie and other brand bathroom cups. This is designed to be an easy print with PLA. There is also a version 2 if you prefer a gap that widens as it gets higher up. There is gcode for an…
This one is designed to be printed with tree supports and the results are fantastic on my MK4. I printed mine in Overture Professional PLA (Electric Blue) and it's nearly flawless. The dispensing window works well. There's also a pair or…
Nespresso Vertuo Capsule Dispenser. This design holds two of the 61mm x 68mm boxes.
Simple tape dispensers in the form of the legendary beer crate model Tape dispenser for two tape spools side by side. You can easily store and use 2 types of tapes for example. Model containes 4 parts: Crate beer Lid with cutter part…
Candy Dispenser for Peanut M&Ms. I wanted one that used an auger to feed the M&Ms (to minimize jamming), used the 62 oz container from Costco and had a separate tray (that I could use to empty the M&Ms into my grandkids hands). I printed…
This isn't a very complex remix. All thanks to the original model including the .step file. I've added screw holes for real screws and included hollow areas that can be filled with buckshot, fishing weights or sand (if using sand wad some…
Needed a gauze swab dispenser for my newborn ;) Design By myself in Autodesk Fusion 360 Print Prusament PLA Galaxy Silver 0.3mm layer height 5 % base infill from 2.00-11.00mm 25% infill for first layers (<2.00mm) and towers (>11.00mm)…
This single bead dispenser requires three non-printed components: 1xM3*16 hex screw 2xM3*4 hex screw A suitable spring that fits in the chamber, I used a 12 mm diameter x 100 mm spring Watch the below video on how to assemble and use:
Braid sold for slot car pick ups is often sold in one meter lengths that you need to cut yourself. These lengths are usually sold with no container, as a loose coil, which can be a PITA to put back where it goes pretty much every time you…
Be a better sharer and make sure you never run out with this basic tape dispenser that is setup to hold two rolls of standard scotch tape or an equivalent. The main shaft uses a threaded cap to keep the rolls from falling off, and…
ACME thread adapter for a Solo 330 Aerosol Smoke Dispenser. Had some very hard to reach smokes that the Solo pole would not get to. Made a ACME Female thread adapter to fit on a various number of painters poles. Now the sky is not the…
This lid is designed to go on a mason jar and allows for a spinning disk to close the opening. It wouldn't be water tight, but should keep anything the size of rice or bigger inside. If you line it up on the build plate, it can be printed…
Dyspenser do zaklejek na przestrzeliny z dodanymi napisami i oznaczeniami strzelnicy Braterstwo W23.
Description A simple, yet stylish dispenser for doggy poo bags. Printing Options The enclosed 3MF PrusaSlicer model files include: A version for single-color model with no embossed image (smooth top and bottom) A version with a bone image…
I tried a few trash bag holder / dispenser designs and they were pretty good. Ultimately I made this, combining the features I needed and avoiding the snags. Handle a variety of brands, roll sizes - especially larger ones (we usually use…
This insertable bin is 2x2 units footprint, and one unit high. It's stackable, and compatible with Auer (tested), and might be compatible with more of the similar systems. Pictures show dual colour prints - the files attached do not have…
While refilling the SimpleHuman soap dispener, the lid slipped through my fingers, fell to the ground and shattered to pieces… Question: Should I buy a replacement part or design my own lid? After reseaching the price for an original lid…
a generic wall mounted with screw slide holes to mount ,open top for easy refill with a cut out for dispensing via botto 236.80mmkx62.80mmwx160.16mmh
This is a wall-mounted Cotton Rounds dispenser. The design was done referencing the Swisspers brand of Cotton Rounds but may work for others. Wall mount fastener holes are sized for #6 pan head screws, so any drywall anchor or wood screw…
Cats survival instinct makes these furry companions tend to drink water from above the ground level to avoid poisoning or bacteria infection. This little stand will help your pets keep their instincts intact and also let the spilled water…
Best results with PLA, layer height 0.7 mm, 25% infill and no supports. Created in FreeCAD. Printed with Prusa mini+.
--V1.2-- Added _TS for those who wants to print without corner brims and smaller spindle to accommodate wire spools with smaller internal diameter. --V1.1-- Adjusted fittings of conical ends to the spindle. --V1-- Too many wire spools,…
Like the original design print the outside twice and the inside once. There is also a battery icon which can be attached to the front.
Remixed from: Bees water platform to drink with bottle reservoir by Petos Safarik | Download free STL model | Printables.com Added perches on all sides so that humming birds can use it as a bird bath or a drinking platform. Printed in red…
Ich habe mir hier einen kleinen Halter für den Wickeltisch zusammengestellt, damit die Packung der Wattetücher nicht auch noch neben dem Wickeltisch rumfliegt. Designt habe ich diesen Halter passend für die Wattepads von Rossmann der Make…
A simple container and dispenser for disposable acid brushes, commonly used for spreading glue, oil, acid, flux, solder, and pipe dope on projects. This dispenser was built for 3/8" acid brushes measuring 5.5" in length (specifically…
Simple tape dispenser with spikes, for easier dosing.
August 2025: Updated models for aliexpress knockoffs bottles. Every dispenser is different, fitting may vary. Safety lock for Menda (Menda-like) pump dispenser. Lock protects against accidental pressing of the pump. Print instructions 0.2…
box for storing clothes tissues
Print settings: Perimeters: 4 Solid layers Top / Bottom: 5 / 5 Scarf joint placement: Contours Material: PETG Optional Modifier: Range 0.00-141.00 mm Fuzz skin: Outside walls point distance: 2mm thickness: 0.1 mm Required hardware: soap…
This is a cover for the IKEA EKOLN soap dispenser that is simply put together. I printed the parts on my MK4S using MMU3. All parts PLA 40% lightning infill
It always bothered me that I couldn't get the last bit of soap out of Method hand soap dispensers apart from rinsing out the bottle and washing it all down the drain - this seemed wasteful and unnecessary. Using this coupling, I can now…
A sturdy wall-mount holder for dispenser bottles with a maximum diameter of 70mm (2.75"). Designed for easy installation with screws, this holder provides secure and accessible storage for various bottles, including hand sanitizers.…
This tea bag dispenser is made of four parts. The main tea bag box, the lid, the wedge to push the bags down the ramp, and the cleat that gets screw/glued into a wall. You can easily lift the dispeser off the cleat and fill it or take it…
Tangle free 64 AAA battery dispenser. On my way to another (bigger) project about battery management, I thought you might like this battery holder or dispenser which stacks the batteries tangle free, which most holders I tried so far…
A battery dispenser for the IKEA Skadis board. It holds both small LR1130 and bigger CR2032 batteries. Possible improvments: Currently it's a bit tricky to get out one battery - especially the small ones. Maybe an angled lip that pops out…
A first-in-first-out dispenser for reusing KN95 masks
A reproduction of the key who open the toilet roll dispenser in my company. Print instructions You have two options : use the pre-sliced G-code and print it on your MK3S+ download the best slicer ( PrusaSlicer ) and use the following…
used wit double sided tape. Neuu is with a thumbtack for stability.
Tried it with fuzzy skin an it looked nice
In a world health crisis, having clean hands is on everyone's mind. But has it ever occurred to you that when you open the faucet, your hands are dirty, and when your hands are clean, you touch the dirty faucet. The same is true with soap…
Point of this remix was that it should be able hold a liquid like water. Original model was good for paste like fillings. Print it next to each other. Don't Print it as one piece. Printed with PLA. Layer height 0.2 mm. Brim recommended.…
The Zevro dry food dispenser only allows a fixed dosage per portion. But what if you want to offer less, for example half a portion? This redesign allows just that. You can use the supplied raised decks to vary the dosage. They reduce the…
Description: Upgrade your kitchen setup with this compact base for glass bottle water dispensers. Designed to fit the Prusa Core One, this remix features a slightly reduced size, optimized holes to minimize filament usage, and additional…
just a simple wall mount replacement option for Sellars TOOL BOX® 200-sheet shop towel dispenser. enjoy! (oh I haven't printed and tested it. I'll doublecheck it and let you know :)
This was a lot of fun to design and print :-) After some friends from metalab visited realraum a while ago, they improved our space by adding a few small shelves („Regal“ in German) and labeled a lot of things as “regalraum” which is a…
This modernly designed tea organizer and tea dispenser keeps your favorite types of tea organized and safe. The standard dimensions are 210mm x 85mm x 170mm. The tea dispenser is designed for all common tea packs. About the print…
This is a useful Blade Dispenser for my new Optimized Bed ScraperXL with replaceable blades. The dispenser holds 44 blades and has a hook to which the bed scraper can be attached. Double-sided adhesive tape can be used to attach the…
Egg dispenser hold 10 eggs from S to L sizes (up to 65x45mm). Print recommendations: Filament - PLA, PLA+ Layer 0.2mm, 2-3 Walls Infill 10-15% With Brim 5mm The Support is not important.
Egg dispenser. Add model for bed 256x256x256 type bambu. 3110_Bambu dispenser eggs.3mf New model with solution break eggs https://www.printables.com/model/1223603-2025_dispenser-rotary-egg New model 2025…
Inspired by commercial products and self-made solutions, I decided to design and print my custom version of a Nespresso capsules dispenser. It wanted it to be nice to look at, functional and simple at the same time. What you see here is…
17/08/2023 Update: NOW YOU NEED LESS SPACE. I have lowered the inclination of the upper ramps by one degree, resulting in a maximum design height of only 139.089 mm. Hello there! I create this model of can dispenser because i couldn't…
Drink organizer. New model 2024 https://www.printables.com/es/model/781648-2024-stackable-rotary-drink-dispenser New model 2023 https://www.printables.com/es/model/377642-2023-stackable-rotary-drink-dispenser And modular model :…
This space saving battery dispenser is designed to hold both AA and AAA batteries, 12 AA and 13 AAA. There is a Voronoi pattern on the sides of the magazine to make it easy to see how many batteries are left. The drawback of this design…
This is a remix of the cool Thingiverse project of mordaha that I optimized for my requirements in the following terms: used 2x M3x20 screws as lever axles instead of 1x M3 screw and 1x filament levers have a bit more space to each other…
Update: 2025-11-13: Added a remix for a laser-cuttable model. https://www.printables.com/model/1479675-dishwasher-tablet-dispenser-laser-cut-version Dishwasher Tab Dispenser – Sturdy & Simple A no-nonsense, ultra-durable 3D-printed…
This Gridfinity battery dispenser fits 10 AA / 13 AAA batteries per 2x2x1 Gridfinity block, plus one dispensed battery. If you need to store more batteries, you can print another block that feeds batteries into the dispenser block…
