Liczymy pasujące modele…
Frsky Archer R6 casing During the design of the casing, care was taken to ensure that an additional strain relief for the antennas could be realized. In addition, the housing should be as compact as possible. For mounting in the model…
Puzdro na RC modely lietadiel Frsky S6R Print instructions Značka tlačiarne: Prusa Tlačiareň: I3 MK3S Podpory: Ano Rozlíšenie: 0,20mm Výplň: 0% Perimetre: 2 Filament: PLA
For models with an gas engine, the lower holders can be printed in TPU to reduce the vibrations. For the assembly you need 2 carbon fiber tubes with od Ø4mm and 45mm length as well a screw with approx. 2,2mm diameter.
Use Velcro or double-sided tape to secure the electrician's cable ties to the model and, if necessary, provide greater security. for the antennas fixed with heat-shrink material.
Small wrench to tighten the switch nuts on FrSky Transmitters. Wire used is 0.03 music wire. I had to clean out the holes with a drill slightly smaller than the wire, then pressed them into the holes. For the print, I used 0.30 layer…
The FrSky XM+ receiver has very fragile antennas that often get damaged if you don't handle them carefully. To fix this, I designed this case to hold the antenna wires in place and provide a good surface for gluing to the fuselage. I've…
Frsky Neuron 8A SBEC mounting brackets mounting brackets have been designed to be as small as possible for fixture two O-Rings are needed
The tray riser prevents TX connector/cable damage during programming of FrSky 12XS with darkOne TX tray. As the tray original rear bottom supports are only glued to the base, there can be dimensional inaccuracy. The raiser left and right…
Simple case for the FrSky R-XSR receiver with a 20mm hole spacing. Can be mounted on the bottom of the Volador VX3.5 with M2x6 screws Printed on a MK4S with PLA and TPU, 0.15mm
No straps. Fragile during crash.
mount for your RC plane for Frsky TDR10 receiver receiver : https://s.click.aliexpress.com/e/_Dks9clX
FrSky TD R10 mount including 2.4ghz antenna mount. Receiver is mounted to holder using thin tape. holder and antennas secured with zip ties. The original OnShape file for editing can be found here…
Simple 2 part enclosure/mount for FrSky pitot tube. The two bottom holes are for bras insert with M3 thread to mount to aircraft surface. Category: Hobby
A bracket to mount the FrSky TD R18 receiver with fixed antenna positions
EdgeTX , a modified Firmware and a Radiomaster TX16 touch enabled screen make it possible for the FrSky Horus X12S radio transmitter to also have touch functionality. The increased thickness of the touch enabled screen though makes it…
This is an adapter for the TBC Crossfire Micro and Full TX, which will fits right on your FrSky Taranis X-Lite. Wiring All you need to know, how to wire it up, you can find on my Blog: English:…
I think these will fit the x20 (non S model) or the new X20 Pro as well. Let me know if they don't. This model prints upside down and does not require any supports, although I did find I got more reliable adhesion when I printed with a…
Designed to make the receiver and antennas a self contained unit to mount in an R/C plane, car, boat, or whatever you want. Assembles with (5) m2 socket head screws. Can be mounted using servo tape or extend screws through base and into…
I made this to replace the broken cover on my X9D. It's based closely on the original moulding, but with a chamfer at the root of the catch to avoid stress risers and aid printing. It fits nicely on both the FrSky X9D amd Jumper T16. The…
Snap-on bracket for mounting TD MX. Version for receivers with soldering pads and JST connector (v1.6) included. The connector version features a safety latch. Cable tie mount for 2.4G antennas :…
I modeled a replacement slider for the FrSky X20 and X20S RC transmitter that flips the long part of the slider to point down. This is more comfortable for me to use during flying. Be very careful trying to fit this on after printing. If…
Simple FRSKY Archer SR8 PRO receiver holder. Use a rubber band to secure the receiver.
New design. For X20 & X20S Gimbal protector. It is also protecting the switches & potensiometer. Printed also in GLOW IN THE DARK PLA. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: Yes Filament:…
Custom Rotor Riot themed gimbal/stick protectors for FrSky Taranis Q X7.
Designed to make the receiver and antennas a self contained unit to mount in an R/C plane, car, boat, or whatever you want. Assembles with m2 socket head screws. Can be mounted using servo tape or extend screws through base and into…
Attached is support for the FRSKY TENDEM X20(S) transmitter. lder suitable for this model. So here is my desig for the support/holder. You can use a single leg or dual legs. Also my X10(S) Support :…
Pupitre élégant pour radiocommande X18 Frsky. Il se range dans la valisette molle avec l'émetteur. Il protège les manches "gimbals" de la radiocommande durant le transport dans la valisette. Les différentes pièces peuvent être plaquées…
I've now flown many hours with the stock x9d+ battery and it simply does not last long enough for my liking. I had a few spare 18650's (that I use for my goggles) and I figured they would make a great replacement for the stock battery of…
This is an antenna mount for a pair FrSky TWIN antennas. It is designed to be mounted on the back of the elevator servo (low-profile, full-size, not mini) of a SAB Kraken 580. The sleeve portion of the dipole antenna snaps in place and…
FrSky Tandem TDMX dual-band receiver Case (new version, not soldering required)
Frsky Taranis X9D M9 gimbal protectors There are few options here on Thingiverse...I've wanted better fit and wider opening to fit many custom stick ends (stick opening dia. 12.5 mm) Printed in PLA, infill 100%. M9 gimbals , highly…
Mount for Frsky r-xsr Receiver and FPV video antenna. Works best with flexible filament. Print instructions Category: R/C Vehicles Summary Mount for Frsky r-xsr Receiver and FPV video antenna. Works best with flexible filament. Print…
Frsky TD MX mount by slide receiver: https://s.click.aliexpress.com/e/_DnpZLtj
A case for transporting my radio to and from flight locations and storing it at home. It has a locking tab at the bottom and a Velcro strap (25mm wide) up top to keep the lid secured. Also has loops for a carrying strap (Up to 25mm wide).…
This is a minimalist case for the FrSky RX6R. Two versions are provided, one with access to the S-Port socket (as shown), and one without. The case fits receivers with PWM ports and bind button on the same side of the board (this is the…
This is a drop in replacement for the original Taranis Q X7 Menu Buttons, Power Button and Dial. I printed these in neon yellow saintsmart TPU and after some tweaking of the model these fit and work absolutely perfect for me! Except for…
I like a bigger back momentary SI button on the X20S so I designed this. It replaces the plastic mechanism on the inside and has a screw on button top. For the internal part, Support should only be used on the flat area that is suspended…
Print it yourself or order from Shapeways ! This gimbal protector has a larger size hole for the stick, to accommodate the stick of the M9 gimbal. Category: R/C Vehicles
FrSky receiver mount - flat Category: Hobby
Introduction This mount is used for attaching a FrSky Archer Plus RS Mini receiver to the OMP Hobby M1 EVO radio-controlled helicopter. The mount replaces the lower carbon fiber “Frame Middle Plate” of the original model and adds an…
radiomaster ranger nano back adapter for frsky x9 lite and other
This is just a remix of jessegyger's strap. The original model works great, it is a great job from the designer to make it such a good fit, but I wanted a simpler version so I removed some things like the hook that receives the cover, the…
A quick-to-print case for the FrSky G-RX6. Provides proper protection. The signal pins for CH's 1 & 6 are marked with a small dot. Instructions: Print the two parts of the case Remove card wrapper from receiver, cut a piece 21 x 18 mm -…
Support auf Buildplate notwendig!
Tested and ok with 3s 2200mah Lipo TX power via balancer connector, Crossfire module via XT60/XT30 mods: closed the hole in the back/front larger cutout for powerwires for Crossfire Module print in PLA/ABS, works fine SUPPORT NEEDED…
I needed longer stick ends than are provided with the Twin X-Lite S. I fly mainly gliders and wanted more throw on the stick ends. I also wanted the ends to not be uncomfortable to use for hours at a time. I don't need needles going into…
FRSKY receiver ARCHER RS protective case. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: No Filament: Tesla Filament PETG Category: Hobby
Cases for the FrSky XM and XM Plus receivers to provide a little more protection than the clear shrink-wrap that is installed from the factory. This is a simple two piece case which allows access to the BIND button and connections. I'm…
Hi, Using this adapter you can mount rp-sma pigtail and use any external antenna you want. There is no need to modify/cat/etc Taranis' case, just plug adapter instead of original antenna. Category: R/C Vehicles
FrSky GR8+ receiver mounting. for screw or glue mounting for comfortable work, you can take it out and in easily without glu the receiver itself. I tested it on different models and hard situations. Print parameter: PLA/PETG 0.2 layer…
Battery compartment cover that I modeled for my FrSky Taranis X9D+, since the model I remixed it from has sloppy tolerances and I thought I could do a better job. Keeps the original cover aesthetics, has a thumb grip for easy removal, and…
Fit the X-20 Series of FrSky Transimtters and protects the three-axis gimbals sticks. I printed it out of PETG with 20% infill, three perimeters and gyroid infill on a .6 nozzle. Should work with any transmitter with these types of sticks…
Spacer to improve the ergonomics of the FrSky X20S transmitter. I found that the position of the radio was uncomfortable and it weas unnecessarily short. This spacer makes the height more similar to my other radios. Printed in ABS on a…
A table stand for Taranis X9D Plus. This stand has room for the USB cable when playing simulators. Easy to print without supports. Originally published in 2018: https://www.thingiverse.com/thing:2981532 Please post a Make if you make…
Receiver mount for 220 frame quadcopter.. connects underneath top plate to standoffs over the FC. For 3mm antenna tubes sold at hobbytown USA. This design clears the props and is under the top plate between camera and FC, which is a…
It is a remix of taranis gimbal protector originally designed by ErgoFPV. https://www.thingiverse.com/thing:3191975
FrSky SR8+ receiver mounting. for screw or glue mounting for comfortable work, you can take it out and in easily without glu the receiver itself. I tested it on different models and hard situations. Print parameter: PLA/PETG 0.2 layer…
I decided to upgrade the case for my FrSky X20S and ordered one from AliExpress - https://www.aliexpress.com/item/4000677757547.html (size: 330x235x170mm). The original insert fits right in but leaves a 3cm gap on the side so i designed…
This is a folding mount for the FRSKY Taranis Q X7 or QX7 S. This will allow you to mount a LCD monitor that has a screw mount on the bottom of the monitor. Included screw size is the standard 1/4"-20 that fits most tripod mount LCD…
A simple mix of the official ELRS cover and this one , to add a 30mm fan and mainly to keep the xt30 plug on the FrSky R9M 2019 module. Also changed the hex pattern a little bit.
I didn't care for the factory roller button on the Frsky X12S Transmitter so decided to have a little fun designing/printing a replacement. Now my Horus has a proper eye. Print instructions Category: R/C Vehicles Print Settings Printer:…
A Holder for the Antenna witch can be secured by shrink tubing. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: Yes Category: R/C Vehicles
Created these protectors as I preferred the separated design compared to other protectors. I also use larger sticks so needed additional space for them to fit. Printed in PLA on an AnkerMake M5 .2mm layer, 2 walls, 15% infill. Print as…
3D-Printable replacement for the module bay cover Printed out of asa-cf
I am a big fan of the work from https://www.thingiverse.com/bgill142 . He came up with the absoluetly smallest possible case for the TBS Micro TX. However, his design is hard to print if you don't happen to have an SLA Printer. Also, I am…
A must have to protect the receiver along with the week cardboard shell. Mine was a perfect fit so probably wont need size adjusting. Print Settings Supports: No Resolution: 02 Notes: Print antenna holes down Category: R/C Vehicles
These stick ends try to give you the gamepad thumb stick feeling as you know it from your Playstation or other console, while flying your quad. I found this model on Thingiverse but recreated it from scratch to optimize the printability.…
I wanted a simple and short stickend to my X-lite so i designed this. It only raise 2mm over the threaded shaft and has a little bowl at the top. The diameter is 10mm. I printed this in TPU to get a good grip, i can press it down the…
I modified the gimbal protector to fit with the larger sticks. It also has a bigger cutout in the center to accomodate for a aftermarket balance bar. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: Yes…
This can be used as a regular replacement battery cover with the advantage that it allows using two 18650 cells. Please see the project page for more information and updates:…
I looked for a tiny and reversible antenna mod adapter (something with no glue, no sanding, no cut, and if I want to put old antenna back again, just pop off the adapter), but I found only a few large parts... Just print it and put some…
Spacer to improve the ergonomics of the FrSky X20R and X20RS transmitters. This is an adaptation of the one I made for the X20s to fit the newer style radios. I found that the position of the radio was uncomfortable and it was…
FrSky XM+ Holder Für 30mm Befestigungsabstand Den Empfänger einfach von vorne einschieben und einrasten lassen ... ... For30mm bolt pattern Simply insert the receiver from the front and let it click into place Category: Electronics
FrSky Taranis X9 Lite Radiomaster Nomad Adapter. Remix of: https://www.thingiverse.com/thing:6855518 Added V2 with more stable standoff if needed now with STEP
FrSky XSR mount. Fits between the 2 M3 standoffs at the back of the RCTimer argonaut hexacopter frame. Tray has been widened to accommodate the extra layer of heatshrink added after the addition of a pin for RSSI. Category: R/C Vehicles
The FrSky XSR-M/XSR-E mount is a reaaaallly tiny receiver (20x20 mm in size with 15x15 mounting), having 16 channels and telemetry. Since I couldn't find a suitable mount/adapter for it (in combination with my frame), here's this little…
Let me start off with saying this mod is not for the faint of heart. I saw there was a need for a more secure battery cap with the new FrSky X-Light remote, so I designed one to hopefully help out a few fellow pilots. Below is a step by…
An adapter that allows you to mount an FrSky X8R reciever to the Taranis QX7 remote to the Traxxas stampede RC car. This includes spaces for antenna and pwm connections.
Remix to make these work with the FrSky Horus Print instructions Category: R/C Vehicles Summary Remix to make these work with the FrSky Horus
This is a small box for the Arduino Nano and the R-XSR FrSky Receiver. I use this instead of connecting my Taranis via USB to the Computer to play in Simulator(s). This way you don't need to have the irritating USB cable connected when…
Attached is support for the FRSKY X12S transmitter. The leg is updated to V2 after some feedback. This is a redesign from my X10S : https://www.thingiverse.com/thing:2843888 Bill of materials : M3x20mm Round Philips Screw + M3 Nut - for…
Attached is support for the FRSKY X10S transmitter. I recently purchased the new FRSKY remote control and found that there is no support/holder suitable for this model. The grip is wider and the handle is coated with rubber, which I did…
FrSky R9 Slim and Slim Plus mount for 220mm frame Category: R/C Vehicles
This is a simple wall-mounted holder for the Frsky Taranis Q X 7 remote. It uses 2 screws. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 30% Notes: Print the model right side up and…
The original sliders are hard to reach (on touch sense) when the transmitter is locked in a transmitter tray. Therefore I designed this alternative slider. Print Settings Printer: Creality Ender 3 S1 Pro Supports: Yes ( I printed top side…
Gimbal Protector for FrSky Taranis X-LITE. Please Test :). Category: R/C Vehicles
Gimbal Protectors for FrSky Taranis X9D with Umbrella type stick ends. This stick end is significantly bigger than the original and the lotus type. Since I didn't find anything here i designed and printed my own. Printed in Black PETg @…
I've printed http://www.thingiverse.com/thing:703700 some time ago to mount my FPV monitor to the Taranis. Thing printed very well, and fitted both the taranis and the monitor, but the screen angle was too flat for me. To solve this, I've…
FrSky Archer Plus RS 2.4GHz Receiver Case
This is a replacement battery cover for a FrSky Horus X10/X10S Express. The Express is the version with the Access firmware and has a battery door. The first generation Horus X10/X10S did not have a back which supported a battery cover…
A receiver mount I did a couple of years ago for the now discontinued FrSky XSR Rx. Allows mounting to a flat surface and provides the ability to keep the antennas orthogonal all in a semi-compact package. Use double sided tape to mount…
A FrSky X9E Gimbal Protector Print Settings Printer: CL 260 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 20% or more Category: R/C Vehicles
Feb 2026: Decided to move a few of my models to public domain. Hey! So this is a mount for the FrSky XM Plus receiver. It's meant to be mounted on a 30.5 x 30.5mm stack (The size used for 5" builds.. So, the regular size) Use a zip-tie to…
use a 6 pin pin header I used 2x4x8mm acrylic glass for RGB LED's Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100% or 1.6mm wall Filament: 3D Ware PLA Notes:…
Bay is 8mm and the top plate is 1mm tall. 9mm together (duh). Fits r9mm and the T antenna for the Frsky R9M. Use a small piece of 3m foam tape to keep the receiver in place. Also make sure that there are no sharp bends in your antenna…
