Liczymy pasujące modele…
Update 1: Small optimizations to the casing Added a small groove for lifting the lid Added some space inside on the back for potential cables Hello, here's a small project that I designed. I wanted to combine a small ESP32-C3 Super Mini…
Please comment, rate, and post a make! Update 2/1/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options. A simple case for using an LD2410C radar sensors with an…
Case to hold a LD2410 MMWAVE sensor module and a Wemos D1 mini board. The radar module can be rotated horizontally to adjust the angle and direction it is sensing. Four parts: The case that holds everything A holder for the radar module.…
This is a redesign based on the idea and software from Ultimate ESPHome DIY Smart Sensor | fixtSE The individual sensors are clipped in neatly and are not loose in the housing. Printed with PLA, 15 % infill. Electronics used: ESP32 30 PIN…
Please comment, rate, and post a make! Update 1/19/2024: I've added a new back with a ball joint to give better flexibility with printing a single back for multiple mounting options. A simple case for using an LD2410C radar sensors with…
Descripción: Este soporte ha sido diseñado para montar un ESP32-C3 Mini junto con un sensor LD2450 de manera compacta y eficiente. El diseño incluye una base redonda ajustable con sistema giratorio que permite orientar el sensor con…
Spliced together a few different files to fit my own requirements. You may need to re-size/check the carrier dimensions depending on your own ESP32 board. I designed this to use with Jumper cables, i didn't have a screw for the DHT sensor…
This case has slight changes to it and is based off of Digital Juice 's. This update fits the LD2410 with or without dupont wiring and the USB C version of the D1 mini ESP8266. I included a text file of the .yaml file that is working for…
The model has multiple axes of rotation and is quick to assemble. You can also remove unnecessary parts of the fastening mechanism! This model additionally uses 8x3 magnets and 2x8 bolts. The software can be found on this page :…
Case for HLK-LD2410C mmWave & D1 mini ESP8266 to be added in a room or to be put on a wall. Material used for printing: PETG
EN: This compact housing is designed for an LD2450 radar sensor with Bluetooth antenna and an ESP8266 Wemos D1 Mini V4. It is based on F-Square's multi sensor design , but is a new development except for the rear ball joint . The radar…
Caja para D1 Mini y LD2410
Adjustable Case for ESP32 WROOM (38 pins) + LD2450 This case is designed to provide a functional and aesthetic solution for projects using an ESP32 WROOM (38 pins) and an LD2450 sensor. Key Features: Ventilated design: Hexagonal grille…
Ce projet DIY est non seulement accessible et économique (coût total d'environ 7€), mais il est également personnalisable pour s'adapter à divers scénarios de domotique. Que ce soit pour allumer les lumières en fonction de la présence ou…
No supports needed. Model in picture printed on Prusa MINI with PLA.
The firmware can be found on the official website esphome
I was in search for a case for the popular LD2410B radar presence sensor. However, non of the versions I could find matched what I was looking for. I had LD2410Bs with and without headers here. I also ordered different USB-C breakout…
Human presence sensor housing, could not find any casing for the older ESP 8266, this is my first design so, feedback are welcomed Printed with a 0.2 resolution. Use 4 wall layers if to avoid infills on the lid. Screws needed: 2x 25mm M3…
A wall mount radar presence sensor with a LD2412 that gets directly attached to the Wemos D1 Mini Esp32. EspHome and Home Assistant recommended. Fitting yaml is provided as txt (restriction from printables). Instructions: bend the pins of…
The case is designed to house ESP32 C3 Super mini modules with OR without pins soldered to it. The lid has two variations: Plain and with radar symbol. Features Space for the ESP32 C3 super mini and HLK-LD2450 modules, bluetooth antenna…
Case for a LD2410B combined with a ESP32-C3 SuperMini. No supports required.
USB micro-use/typeC cable or 5V dupont wire power supply Hardware: ESP8266 D1 Mini | W:23.2mm X H:34.3mm HLK-LD2420 | 20mmX20mm Dupont 2.54 X 2pcs (Optional) I have a spare Xiaomi motion sensor base, connecting to the case with a M3*8…
Radar dish support for HLK-LD2410C motion sensor mmW 24GHz. Printed with 0.4 nozzle, PLA, with organic supports.
Case designed to fit following components from Aliexpress. There are many clones and alternatives out there with very slightly different dimensions. WeMos D1 Mini ESP8266 ESP-12F WIFI HLK-LD2410 LD2410 24G FMCW 24GHz *12/26 - updated…
In this case fits only a LD2410C, see the pictures. This is meant for bluetooth use case. So if you are integrating this sensor over bluetooth to Home Assistant or any other Home Automation Software, this Case fits perfectly.
Sensor housing for the esp32 super mini c3. I printed on PLA and the lid is a snap in design (though feel free to modify to use screw posts). The ESP sits very snuggly in the case - so you'll want good tollerances.
Case to house LD2410 and D1 Mini. Printed in PLA, no supports.
This case is based off of Digital Juice's. This update fits the LD2410 and ESP32 C3 super mini from Aliexpress.
Small case for the ESP32 and LD2450 with mounts for 2 * 6x3 magnets. Prints without supports. I use this to hang it below my monitor and integrate presence detection in Home Assistant. Designed in OnShape, link here .
I Modified the project to be able to store a LD2410C instead of the temp sensor. Also i opened part of the top case for the light sensor, as the measurements were pretty low. There is plenity of space for the cables, so you should be able…
This Radar Presence Sensor is easy to build and pretty cheap considering its performance. The firmware uses ESPHome . The sensor uses the universal ball-joint design so it can be oriented for accurate detection. I provide a skadis mount…
Yep. It holds an ath20 board, a panasonic PIR, an mmwave radar, and an esp32 of the 38-pin flavor.
The borders on the cutout part might be a bit thin. I did my best, so consider this a proof of concept . Modifications made using Tinkercad.
A wall mount radar presence sensor with a LD2410C that gets directly attached to the Wemos D1 Mini Esp32. EspHome and Home Assistant recommended. Fitting yaml is provided as txt (restriction from printables). BOM: D1 mini ESP32 with…
WORK in progress Hello, I designed a Case for the mmWaveRadar-sensor HLK-LD2410C-P from Hilink. It's a first version, more a tryout. The sensor is the version with 2.54mm pinout. It's the “friendly” one. You can better solder it, as the…
Case for ESP32 C3 Super Mini and LD2450 with USB C Connector. Backplate snaps in place. added an inlay for the case as the red led shines through white filament 2025/07/04: added ceiling mount, requires 1x m3s threaded bushing
Rectanglar case with snap fit lid and visible sensors
I have designed and printed these cases for personal use in PETG. It can be panned and tilted and has a cutout for the USB cable. Software in my case is ESPHome connected to Home Assistant
This is a remix of the presence sensor originally designed by @FSquare_1622667. I made a few tweaks to suit my needs: Replaced the original screws and inserts with plastic screws (I didn’t have the metal ones at home). Thinned the walls…
Slim protective case for the LD2420 24Ghz mmWave Radar Human Presence Sensor like the Hi-Link HLK-LD2420 from AliExpress Similar to my other display screen and ESP32 cases, this provide a minimal case with easy access to the pins for…
Please comment, rate, and post a make! A simple case for using an LD2410C radar sensors with an ESP32 C3 Mini that can be mounted to the HSW. I've included a little spacer that can be slid over the pins of the LD2410C to help with…
To print the cover with the logo in two colors change the filament to a different color at layer 4 and 6.
Original project: https://www.printables.com/es/model/189821-d1mini-sensor-case-dht22-bh1750 I Modified the project to be able to store a LD2410C instead of the temp sensor. Also i opened part of the top case for the light sensor, as the…
---- new model without battery ----- In the free applications for home automation, you can create your own sensors to control/detect the environment. To create a detector/sensors, you need to have some electronics cards to create a new…
Read my article about this project: https://www.strangeplanet.fr/devlog/posts/2025/03/mmwave-presence-sensor/ The case is mounted on a orientable ball. To assemble the ball to the case body you will need a 20mm M3 screw and a threaded…
Same size as the original, just added a mounting-option and changes vent holes.
I designed a small enclosure for the HLK-LD2410B-P mmWave sensor bord for use in Home Assistant. More details can be found at https://github.com/jonnybergdahl/Sensor_LD2410B . I have included the Fusion 360 file so you can remix it as…
Case for ESP32 and LD2410C MMwave sensor. Fits LD2410C and ESP32 with dupont connectors. Use double sided tape or hotglue to mount ESP32. Use M3 25mm for base and lid x2 M3 16mm for arm. x3
Hi there, Sharing my little bathroom mirror project, specifically the part with a housing for LD2410 mmWave sensor which then connects to a d1mini controller with ESPHome for automated bathroom mirror ledstrip control. Features easy…
Rectanglar case with snap fit lid and visible sensors
Enclosure for a DF Robot Beetle ESP32-C6 and a LD2410C. The enclosure is a tight fit for the C6 but it fits nicely. You may need to push the USBC male connector from the C6 into the enclosure's USB hole from the outside once or twice at…
Simple case for the sensor LD2420. onshape link: https://cad.onshape.com/documents/7fe9b2202ecb885bffb6e2a3/w/aa93626d576c4e4043e3f4c7/e/48be5b06ba6e0a77ca0ae2fc?renderMode=0&uiState=66ef622f6caf30072eaf8ffb
Fits a Lolin D1 "Mimi" v4 with USB-C and LD2410.
Case to make a presence sensor with an ESP32 NodeMCU32s and an LD2450 mmWave sensor, the lid also has holes to glue 9x3mm neodymium magnets. The ESP32 and LD2450 should not require any glue and should stay in place once the lid is screwed…
Designed this alternative wall mount for the LD2450, as I wanted to mount the sensor flush against the wall using tape. Remixed this remote wall mount for this use case (the design is a bit rough, so I attached the Fusion360 file if…
Aquara inspired simple case for the ESP32-C3 Super Mini with the LD2410C directly attached as in this model. Use paint on support on the USB-Connect surface and the “lock” surface. The holes can be used to “lock” the lid with filament…
Slot-in construction for the LD2410B (should also work with the non-B model) module so that you can put it onto some metal base (space for a disc-magnet 6x2mm in the bottom part). Detection works through the printed material. No further…
Wanted a small case with presence and illuminance sensors with the use of Wemos D1 mini ESP8266. Inspired by : MMwave Multi Sensor fixtSE LD2450 by F-Square | Download free STL model | Printables.com Using the joint , nut and foot form…
Housing made for ESP32. There no mounting holes for the esp32 because the esp32c3 versions from Seeed doesn't have mounting holes zo i fix them in place with a little hot glue. My first remixing a model without any experience.
Heavily inspired by Yoram van de Velde's Case and mount for LD2450 and ESP32 C3 Super Mini I remade everything in Solidworks. Features: Houses ESP32-C3 Super Mini/Pro Mini & LD2410C/LD2450 mmWave Sensor Designed to be wall mounted or…
See description in the main model https://www.printables.com/model/1020388-esp32-d1-mini-ld2420-24ghz-mmwave-radar-sensor-esp Difference : ESP32 S2 mini used and the radar LD2410
I needed an LD2410 case for the Raspberry Pi Pico W. Since I liked this one the most, I reverse-engineered it in Fusion 360 so that I could easily modify it to fit the Pico W. I wanted to share the original files as well, as someone might…
Cover per ld2410c e d1 mini.
Presence sensor for use in Home Automation Parts used: ESP12E (ESP8266) with breakout board, 26x38mm HLK2410c 24G radar sensor, 22x16mm. BME280 Temp, pressure and humidity sensor, 15x12mm WS2812 LED, x4 pixels, 10x32mm. Notes: All parts…
This worked well made from Nylon, though I wouldn't be afraid to try them out of other plastics. In a worst case scenario, they wear quickly, and and need to be replaced again.
I recent got some Low Profile batteries and obviously they are quite a bit thinner. I had designed a oring mount in the summer for my standard size however it didnt work with the low profile batteries. I designed this mount. Uses all…
Wallmount for Battery Charger of E-Bikes from Focus Jam2 / Jam2 HT / Bold2 / Sam2 with Shimano E8000 motor, using a 378wh internal or 378wh T.E.C. Pack Battery. Mountable with two screws to a wall or, using the holes on the backside with…
Holder for LD2410 with Wemos D1 Mini for IKEA Skadis Boards. The Case can be turned to left and right by 50° Parts needed: LD2410B Wemos D1 Mini M3x35mm + M3 Nut or M3x30mm + M3 heat set insert 4x 3x12mm self-tapping screws Print Settings…
I recreated the STL files in Fusion 360 and modified them for the Raspberry Pi Pico W. Additionally, the logo is now suitable for multi-material prints. With the type settings in PrusaSlicer, it can now be printed in any configuration.…
In the free applications for home automation, you can create your own sensors to control/detect the environment. To create a detector/sensors, you need to have some electronics cards to create a new device to add in your Home Assistant…
I recently got low profile batteries and the battery mount I designed didnt work as they were a lot thinner. So I designed this. You will need 2x 44mm diameter oring's, check on eBay. Either 2mm or 3mm. I'm currently using 2mm. Print…
Custom Gridfinity holder for Mast Tattoo Fold2 Pro wireless tattoo gun, spare battery, and wired cord adapter. Uses 1 x 6 standard Gridfinity 42 mm base plate squares.
This is the housing case for the LD2450 24GHz radar presence sensor with chinese cloned Wemos D1 Mini. There's no need any crew, all are snap-in.
Caja con alimentación USB directa para ld2410c. Dos tamaños, según interese orientación del sensor. Para conectores use terminales macho y hembra dupont. Puede conectarse directamente a un puerto USB o, como yo, a un switch wifi para…
In the kit you get 1mm spacers to use one at a time but theres an option part for 0.5mm (U8207) rather than buy the alloy option part, I created it in Fusion. Fitted and works fine. Print Settings Printer Brand: Creality Printer: Ender 3…
This is a complete chasis and wall mount for presence sensor LD2410 soldered directly to ESP32 C3. To solder LD2410 to ESP32-C3 Super Mini - just remove middle pin from the sensor (digital out - not needed as UART communication is used).…
Wallmount for E-Bike 378wh T.E.C Pack Battery of E-Bikes from Focus Jam2 / Jam2 HT / Bold2 / Sam2 with Shimano E8000 motor. Mountable with two screws to a wall or, using the holes on the backside with 2 screws (Phillips Rounded Head…
I didnt like the mounting system on the LD2, they would wreck the stickers on my batteries and you would need to adjust/reshim if I used a slightly different battery or a brass weight. I designed this to work with a rubber oring that…
An ESP32-C3 and LD2410C enclosure for your ESPhome presence sensor needs! No hardware is required, and all parts can be printed in any filament you want (except probably carbon-impregnated filament, since that'll mess with your radio…
This is a simple snap-on adapter for your Fenix LD20 so it can be fit to mounts that are meant for 1" frame flashlight, like many tactical lights. Print with one of the ends facing the buildplate, and after printing & clean up it should…
MMW-1 Human Presence Sensor (Basic Edition) The MMW-1 is a high-performance, compact housing designed for the LD2410C mmWave sensor and ESP32-C3 SuperMini . This design features a technician-grade internal stack and a magnetic mounting…
Thick-USB case: a 12.1 × 6.9 mm pocket in the end wall, so chunky USB-C plugs (up to about 11.5 × 6.3 mm overmold) seat fully. The original slot only fits slim plugs. 16 mm ball back: the original flat back with a 16 mm ball on a…
This print is suitable for Xiaomi Deerma DEM-LD220 for lifting it up from the ground for approx 20cm. Use adaptive triangle infill for less material use
Designed this to hold my flashlight on my opengrid wall, but would work with any Multiconnect system.
wall mount for LD2410 sensors using HA print on peopoly magneto-x
A parametric mounting bracket for four HLK-LD2450 24GHz radar modules on a 1" (25.4mm) square aluminium tube. Designed for outdoor radar sensor arrays. Features: C-channel grooves hold PCBs securely at 90-degree intervals around the tube…
I made a replacement protective cover for the 3LD2203-0TK53 SENTRON. For my use case, both PETG and PLA with standard settigns worked fine.
Housing made for ESP32. There no mounting holes for the esp32 because the esp32c3 versions from Seeed doesn't have mounting holes zo i fix them in place with a little hot glue. My first remixing a model without any experience.
This Radar Presence Sensor is easy to build and pretty cheap considering its performance. The firmware uses ESPHome . The sensor uses the universal ball-joint design so it can be oriented for accurate detection. I provide a skadis mount…
A parametric mounting bracket for four HLK-LD2450 24GHz radar modules on a 1" (25.4mm) square aluminium tube. Designed for outdoor radar sensor arrays. Features: C-channel grooves hold PCBs securely at 90-degree intervals around the tube…
This is the housing case for the LD2450 24GHz radar presence sensor with chinese cloned Wemos D1 Mini. There's no need any crew, all are snap-in.
This case has slight changes to it and is based off of Digital Juice 's. This update fits the LD2410 with or without dupont wiring and the USB C version of the D1 mini ESP8266. I included a text file of the .yaml file that is working for…
To print the cover with the logo in two colors change the filament to a different color at layer 4 and 6.
I had a PIR movement sensor in the basement controlling the light, but it sucked pretty bad and I had an LD2450 mmWave sensor lying around. I also found the relay board relatively cheap and just combined both things in a compact(ish)…
Slight remix of the original model by Prashant Sinha . For instructions please see the original model . The only differences are that this model is adapted to use M2 screws, the original model requires M2.5 which I did not have available.…
Using an LD2410B radar sensors with an ESP32-C3 SuperMini or Zero.
Includes an enclosure for an ESP32 S2 Mini or ESP32-S3 Super Mini, which you can flash with ESPHome. Print the bottom layer of the front panel with 0mm thickness to avoid interfering with the mmWave signal. Print settings don't matter…
This is a remix of keirmeister's v2 adapter of the same name. None of my metric fasteners would fit the original, so I've modified it to accept M3 socket head cap screws up to 16mm long and M3 hex nuts. The original 'platter' also had a…
