Liczymy pasujące modele…
designed these to fit in the drive drawers for my HPe Blade center. not perfect but they work. they fit a wide variety of HP servers gen8-10. tried to make a version that was easy to remove, but kept the older model in case they really…
Update: Added 120mm fan version A revised version which enables 120mm case fans to be mounted as lid has been added. I ran this setup with a fan powered by the AK2 Plus board directly for over a week without any stability problems. Read…
I wanted to make a simple case for the smallest ESP32C3 that I could find for use within a Mitsubishi AC. There is a CN105 port on several Mitsubishi ACs that allow you to control the unit remotely without spending $100+ on an official…
DIY mini PC NAS DISCLAIMER: this model was built over the Beelink EQ12, however after some research I think it should also be compatible with the Beelink ser5. Hi Makers! I had some 2.5" HDDs laying around my lab gathering dust and I…
A 120mm fan mount for the “fanless” Topton N100 router PC. It lets you securely mount a fan without case modification.
Beelink Mini PC 12th Gen Intel Alder Lake N100 tried to keep it accurate to 0.02% mm
These are the 3D models in .STL, .3MF and .step format of the shoulder buttons for the Sony PSPGO (PSP-N1000) handheld console. The left shoulder button on my PSP GO broke and I could not find a replacement button. I modeled and printed…
What do you do when you need wheels, but ordering them will take too long? you print 'em yourself - I had a look around, and the ones I could find had too large d-holes, so I decided to make my own. Print the actual wheel in some stiff…
(Print Settings Printer brand: Bambulabs Printer: Bambu P1P Rafts: No Supports: Yes Resolution: Nozzle 0.40mm / Layer Height 0.20mm Infill: Gyroid 25% Filament brand: AzureFilm Filament color: Neon Red Filament material: PLA Notes: print…
Right rack mount for Topton N100 i226-V Mini PC that takes only single 1U. One original bottom screw replaced with M3x40mm. Holds device in place. Printed from ABS with 0.2mm layer, 40% infill, 4 perimeters, 5 top/bottom layers. Design…
This model allows to mount a 2.5" SSD drive on the optical disk bay of an HP ProLiant MicroServer Gen10. I printed it in PLA, on my Prusa i3 ML3. The print requires no supports.
Kabelträger einfach eindrehen und Kabel mit Kabelbinder befestigen
I couldnt find any good wheels for my 150g combat robot that fit my chassis, had enough traction, and stayed on the hub well. So I made one. There are 2 models one for 2 O rings and 1 for 3, size 211 works best 212 can work (from harbor…
Designed for CWWK N100 “ Pioneer Affordable Edition ” Versions M4 Version for normal 120mm Fans, e.g. Noctua use M4x4,0 threaded inserts M2.5 Version for BeQuiet Silent Wings Fans use M2,5x4,0 threaded inserts Print at least with PETG as…
There are different kind of Dia Magazine Slide Feeders out there. Unfortunately, not all magazines use the same pitch. Universalmagazin DIN 108 (Reflecta, Hama, Leica) uses 5.5mm pitch Paximatmagazin (Braun, Revue) uses 5.04mm pitch There…
I have printed these from petg and pctg, and both seem to work fine. Additionally, you also need a roughly 16mm x 2,5mm (5/8" x 0,1") O-ring. PS. If you are using a hose clamp to secure the connection, be careful not to overtighten the…
This is a portable monitor made out of a screen from a broken netbook and a driver board I bought from eBay a few years ago. Print instructions The model of the netbook screen I used was N101L6-L0D and the particular driver board that I…
1U Rack Mount for Topton N5105 i226-V N150 N100 Mini PC
A simple and easy to print Ben10 fridge magnet. Printing Instructions: Layer Height: 0.2mm (Important for multicolor prints to ensure 2 layers for green, black) Infill: 15% Supports: No Rafts: No Brim: No Skirt: No For Multicolor Print:…
This is for mounting the fanless 'router' style Intel Alder Lake N100 mini PCs in a standard 5.25" drive bay (e.g. https://www.aliexpress.com/item/1005006036859811.html) In this case it is used for upgrading the HP N36L/N40L/N54L…
CWWK/Topton Affordable Edition Riser Base to accommodate 80x25mm fan at the bottom Combine with ZeroFlow's 120mm Top Fan mount for significant cooling benefits. Results: Stock fanless 48C 120mm Fan only 30C 120mm Fan and 80mm Fan 24C…
I needed to mount a fan on my “fanless” mini pc to keep it cool. As reported by the seller on Aliexpress , if you want to do more than just a router, you need to add a fan to dissipate the heat. The fan mount I've found was good but not…
Elevate Your Lenovo Legion Pro 7i Gen10 with Snap-On Feet! Enhance your laptop's performance and comfort with these custom-designed snap-on feet for the Lenovo Legion Pro 7i . These feet elevate the back of your laptop slightly, promoting…
Remodeled after the original LF-N1000 rear lens Cap for my Nikon 1 lenses. Prints without support, might have to remove some strings.
I got a HP ProLiant Gen10 Server second-hand with missing screws for the HDD. These specific screws should be T-15 Torx 6-32 UNC. Also, I couldn't find a model that fits. To help myself, I created my own caddy. There exist 2 version, HDD…
A belt clip for the Opinel N10. (Not tested on other models.) Print in as high quality as possible, so the safety that goes into the knife doesn't move, it needs to fit like a puzzle piece. Also, print with as much infill as possible. 40%…
Thanks to the other creators for the original models and step file to make it a snug fit!
This is a simple dock that mounts to the bottom of a generic Aliexpress N100 mini-PC and holds up to two 2.5" SSDs (or HDDs if you really want to). It mounts to the mini-PC with two M3x4mm or M3x6mm countersunk screws. The SSDs are then…
The original case of my Firebat AK2Plus MiniPC choked the SoC to death, so I stripped everything I did not need and started working on a case alternative. This is the first stage of this project, a minimalistic baseplate for the AK2Plus…
DN100/HT100 to DN50/HT50 adapter. Included a small spacer, if your DN100 port is not exactly 100mm. EDIT 16.02.2021 Reuploaded the files with better .stl's (more vertices). Now it's really a round thing! Category: Hobby
Printed in Clear PETG. Requires 1.5 rolls of filament. M3 16MM screws to assembly it. Cuttout for Pico PSU 4pin Mini-Fit-JR connector. Motherboard https://www.asrock.com/mb/Intel/N100M/ Pico PSU https://www.mini-box.com/picoPSU-160-XT…
Printable Motor Mounts for N20 styled motors. The standard version uses 2x M2 nuts or M2 standoffs, with 18mm hole centres. There is a version designed for use with self tapping screws or Polyfix screws (3x8) which is slightly more…
Nach dem HT50-Set hier die vier anderen gängigen Nennweiten: DN32, DN40, DN75 und DN100. In jeder Größe der gleiche Teilesatz, insgesamt 44 Dateien.…
Reduction DN40 to DN100 (50mm to 110mm) ABS 2 wall Vytvořeno pro odvětrávání odpadu.
Infill: 100% Material: PETG Druckbetthaftung: innen+außen
I use Thread-Inserts M4 for the Fans Use tapping screws for fans to secure the adapter. Screw it onto the heatsink fins.
Allows you to hang a GMKte N100 Mini-PC on an IKEA Skadis pegboard. Use two M2 screws to attach the mount to the back of the PC (the holes are already there), and voila. I might have gone a little overboard with the pegs, but doesn't use…
An IKEA SKADIS mount for your mini-ITX motherboard. It's designed for the AsRock N100DC-ITX, but will most likely fit other boards, too. It's very sturdy , prints without supports and if parts are positioned as recommended, layers will be…
Lüftungsgitter DN100 Rohrinnenmaß 104mm Gedruckt in PLA
Simple bouchon à poser sur des évacuations en PVC DN100 pour éviter les odeurs sur les chantiers. Simple plug for use with DN100 PVC drains to prevent odors on construction sites. [BuyMeACoffee]( https://buymeacoffee.com/lafeeleonie )
I have designed a bracket for a PVC plastic gutter DN100 so that there are fewer disputes when feeding the chickens. Printed in PETG standard settings - nothing out of the ordinary. Easy to assemble and flexible in arrangement. German:…
Gedruck in PLA mit 0.4mm Nozzle auf modifizierten Ender 3. Die Druckzeit war 8,5h. FreeCAD Datei verfügbar. Im inneren ist ein rückwärts gerichteter Trichter. Das meiste Wasser läuft über die Außenwand zum Seitenrohr. Wenn das Gefäß am…
To celebrate the successful test flight of the SN10 we decided to create and share a SpaceX Keychain in the shape of the rocket with their logo on it. We eventually created two versions and struggle to figure-out which of the two we like…
Created in TinkerCAD. If you want to edit it there, it's been made public: https://www.tinkercad.com/things/hkYeHfIrBWW-dreamfyre-dr06-mini-pc-case-top Because the fan of the CPU exhausts through the vent holes on this, PLA may be a poor…
Remixed the original to fit the NetDot 10th generation magnetic USB adapter cables. (ASIN: B07QB6HVFY). I'm also not fond of gluing everything together (and possibly ruining the cable), so it has been changed to use 2x M3x20mm bolts for…
A DN100 magnetic dust collection coupling for my planer. It consits of three parts. Part 3 has to be glued in part 1 to have a better alignment of the coupling. I used the following magnets:…
A printable replacement bushing for Napoleon part number N105-0011. Mine broke, so I decided to save a couple bucks and print a replacement. I wouldn't recommend PLA for this since the door gets hot enough to soften that material. I used…
An easy to print DN100 Pipe Holder with a center distance of 120 mm. Fixated with 2x Ø4 screws.
Fix all the problems with fitting those tires
This model is designed for the ASUS N100I-D mainboard inside the Jonsbo N2 case. It mounts directly onto the CPU heatsink and allows you to attach an additional 120mm fan. It's is also compatible with…
The bracket is suitable for the mini PC sold as “Topton pfSense Firewall Soft Router N6000 N5105 N100 4x i226-V 2.5G LAN NVMe Barebone Fanless Mini PC HDMI2.0 DP AES-NI OPNsense” on Aliexpress (as of Nov 2024). It replaces the base plate…
Bei meinem Sohn war der integrierte Ständer in der Hülle vom Tablet gebrochen und ich habe diesen als Ersatz erstellt. Passt einwandfrei und erfüllt die Funktion.
Dust collection adapter from an incoming 100 mm hose to two 40 mm hoses. I use this on my router table to connect both the fence and the router itself to my dustcollector. Works fine with @MariusHornberger 's hose clamps. You have to…
Model for the paddle part of Electrolux N10 vegetable slicer. FDM suitable only for temporary use. Print food compatible part in professional print service. Printed this in ABS to verify compatibility and fit. The M10 thread needs to be…
This is a modified cover for the grinder wheel on the N10 nail grinder (made by Casfuy, acquired by Petpat) to be more useful for wider nails. Nothing about the scad code is pretty. Values from lines 5-8 were measured with calipers and…
Cold-swap LFF bays for DL380 Gen10 SFF Chassis. Uses Secondary Riser Blank for mounting. Requires 5ish small zip ties, and some 1/8" thick foam tape. Note that it is not symmetrical. it will only fit correctly one way. (look thru the…
2U 10" Rack Mount Server Panel — Front I/O + Cooling Solution Custom-designed 2U rack mount panel for 10-inch server racks, bringing all essential I/O to the front for easy access. Built around a mini PC/SBC setup with front-facing power…
The Answer. Also, just having fun trying out a some 3D CAD and printing ideas. More versions on the way. This one : Ancient 42 (simple variation) OnShape is not the ideal tool for creating a "broken and distressed" 42 but it can be done.…
I'm a huge Ben 10 fan and wanted to relive the show by creating Hueforge designs for all the aliens! I've already posted some—check them out on my profile. I'll be posting the rest one by one soon. I think this one turned out great ! Let…
For these wheels, you must print the 2 parts, put them together, cast silicone rubber in between them, and then finally, after about 24 hours, remove the outer 3-D printed part, and you will have wheels for N10 Motors! Supplies: Trial…
Ultra Fan - Test - HP DL380 Gen10 High Performance Chassis FAN engine architecture tests -The UltraFan offers a ten percent improvement in efficiency over normal fans. The construction architecture is currently being worked on alongside…
I'm a huge Ben 10 fan and wanted to relive the show by creating Hueforge designs for all the aliens ! I'll be posting the rest one by one soon. I think this one turned out pretty good, but it might look even better with orange filament…
As part of the DIY Steam Machine craze, I decided to go another route. After much research inspired by other designs and on YouTube, this prototype build aims to be a home theater media PC (HTPC)/Moonlight game streaming, and a network…
Box for ANENG GN102 Digital Noise Meter 30-130dB Sound Level MeterBox for ANENG GN102 Digital Noise Meter 30-130dB Sound Level Meter
Disclaimer vorne weg: Ich bin kein Experte für den Bau von Anlagen für kontrollierte Wohnraumbelüftung. Alles was ihr druckt und nachbaut macht ihr auf eigene Gefahr. Lüftungssysteme sollten regelmäßig überprüft und gereinigt werden.…
I'm a huge Ben 10 fan and decided to relive the nostalgia by creating Hueforge designs for every alien from the series !💚 Check out my profile for more - stay tuned for other aliens👽 Print at 100% infill with a layer height of 0.08mm with…
This is a Gridfinity bin for a Mitutoyo ABSOLUTE ID-N1012. The Bin is 4x2. There is a space for 6x2 Magnets in the corners. Base generated using Gridfinity bin generator. Custom tool cutout designed from scratch.
Holds a TRIGKEY G4 (N100) mini PC (calipered 115.9 x ~102 x 44.4 mm including feet) upright, logo out, with the front ports (2 x USB-A, power, button) facing DOWN through an open floor. The side walls and back plate are opened up so the…
Concept CAD collection for a DN100 PN40 trunnion-mounted ball valve with an ISO 5211 actuator interface. Includes the full assembly, cutaway, valve internals, and sphere/stem unit. STEP files are provided for CAD review and educational…
1U Rack Mount for Topton N5105 i226-V N150 N100 Mini PC
This model is designed for the ASUS N100I-D mainboard inside the Jonsbo N2 case. It mounts directly onto the CPU heatsink and allows you to attach an additional 120mm fan. It's is also compatible with…
An IKEA SKADIS mount for your mini-ITX motherboard. It's designed for the AsRock N100DC-ITX, but will most likely fit other boards, too. It's very sturdy , prints without supports and if parts are positioned as recommended, layers will be…
This is a Gridfinity bin for a Mitutoyo ABSOLUTE ID-N1012. The Bin is 4x2. There is a space for 6x2 Magnets in the corners. Base generated using Gridfinity bin generator. Custom tool cutout designed from scratch.
2U 10" Rack Mount Server Panel — Front I/O + Cooling Solution Custom-designed 2U rack mount panel for 10-inch server racks, bringing all essential I/O to the front for easy access. Built around a mini PC/SBC setup with front-facing power…
Bei meinem Sohn war der integrierte Ständer in der Hülle vom Tablet gebrochen und ich habe diesen als Ersatz erstellt. Passt einwandfrei und erfüllt die Funktion.
part for foldaway bed print diagonally to have more strength on the triangular end part number CN102102694B the black part on the picture ar the original
This is a three-part print that lets you mount an 80mm fan below, and a 120mm fan above, your new Topton N100 "fanless" pc that you just bought only to discover that it overheats and/or burns your fingers. If you haven't bought one of…
Suggested printing in the provided orientation with auto tree supports. Yes, that orientation. You could print it flat (you'd still needs supports), but then layer lines could cause the pegboard “legs” to break off. Use M3 SHCS or BHCS to…
Welcome to my first model in the Printables Store. My model is a leaf separator that filters your rainwater and serves you the leaves in a bucket. Once installed, you don't have to worry about anything else. After 1,5 years of testing I…
Enclosure for custom ESPHome device for Mitsubishi Heat Pump Control using the CN105 port and this project: https://github.com/echavet/MitsubishiCN105ESPHome Specifically, see breadboard layout and components in this post:…
A 120mm fan shroud to replace the piddly wee fan on the Topton N100 ITX board. I mean the tiny fan does an excellent job as it is, but you can only have a 3d printer for so long before you have to print upgrades. You will need 4x M2.5…
this is a laptop and it is quite productive because instead of Raspberry Pi there is a mini-PC with N100 what you will need: display:…
Motherboard: Aliexpress link #1 Aliexpress link #2 Intel N100 (4 cores, up to 3.4GHz, 6W TDP) 1xDDR5 4800MHz, up to 16GB M2 2280 for NVME SSD (PCIe 3.0 x1) MiniPCI for Wi-Fi/BT modules Two USB3.2 Gen2 + one USB2 + up to 4 USB2.0 from…
Created this cover which holds a 80mm fan at the bottom. This replaces the original cover and blows air right into the case, especially on the RAM and NVMe Disk. I'm using it with this stand: https://www.thingiverse.com/thing:6261436 I…
This is the IO shield for Topton NAS motherboard N100, 2x2.5G and 1x10G from Aliexpress. The shield partially covers the HDMI/DisplayPort but does not block it.
This is a guide for making a hole in the top of the minipc box, to allow airflow. Use the f360 file if you need a different size hole. This is the dimensions of the Forstner drill bit i used and the shaft of it. change it to fit your…
Replacement knob for SONY STR-DN1060 Surround Amp Print with 100% infill setting Coppied from original which broke in the back 38.5mm Diameter, 19mm High
A remix of https://www.thingiverse.com/thing:4741285 to add a proper headphone jack hole. I own the “ Linsoul KZ ZS10 ” headphones, with the microphone; this model and the hole placement for the headphone jack work with this model in…
Print recommendations (all should be included in the .3mf file): Prusament PLA Jet Black Print with the aesthetic face up Use organic supports as they come off very well
I designed this model as a spare, since I broke the original. print in petg for food use, if possible coat it with resin
This is a two part cover for a DN110/DN100 ventilation-pipe. It is a very loose fit to accomodate for some soft sealing tape. You can fit a piece of fine insectscreen between the inner and the outer partr to prevent bugs from getting in…
Honeycomb storage wallmount for RMT-AA320U remote - for sony str-dn1080
Wenn ich an meiner MPCNC Primo den Laser benutze sauge ich den Rauch mit einem Rohrventilator ab und lasse ihn durchs Fenster raus. Der Rohrventilator ist fest an der Decke angebracht. Damit ich die Schläuche nicht herumhängen habe, wenn…
The original lens hood was like 20 bucks, so I made my own. Depending on your printer, you may have to carefully file down the tiny plastic tab a little bit so that it snaps in more easily. Since I couldn't find accurate dimensions of the…
My Staco 3PN1010 variac knob was broken so I modeled up a clone replacement. I designed it to be a tight fit on the shaft. It uses 2 set screws to secure the knob. I purchased M4x0.7 24mm long set screws. If you have a tap for the…
![Alternative Case for AK2 Plus Intel N100 Mini PC (Firebat, Kamrui, NiPoGi) [Updated 120mm Fan Version]](https://media.printables.com/media/prints/926938/images/7229417_abf8bd94-445d-400a-9f74-0e1abaf2ebbb_0b6333b6-85d1-470d-b564-e040aaa0a8b8/ak2-plus_case_120mm_main.jpg)
