Liczymy pasujące modele…
Edit 26-01-2026 I have recently developed a new and in many ways better shutter design which I recommend over this version. It does require a few more non-printable components but it may be worth it to many users. It can be found over…
Wydruk około 2,60 €–3,17 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is case was designed to embed all the components needed in the making of a camera shutter by @jamesskelton. Link to his github project page : https://github.com/hackaninstant/Servo-Shutter The box embed : two 3,7v lithium battery for…
Wydruk około 0,18 €–0,23 € nettoWstępna wycena jednego wariantu
My Educational Mechanical Examples Series This model is one of my educational mechanical mechanism examples on 80mm x 80mm base plates. You can find all models of the series in this collection => [Mechanical Mechanism Examples] This model…
Doll-House window frame with opening shutters. For the assembly, use a piece of sturdy filament of 1.75 mm or a pice of electroc copper wire. Scale to desired dimensions.
Introduction This design offers a completely new large format camera shutter, building further on this previous design. It offers a number of improvements making it a more practical, ergonomical and reliable tool. The most notable…
Simple DIY Shutter for large format lens, this one was made for vintage wide angle lens but scaled will work on many different lenses. I added spring for quick “closing” of a shutter, attached it through the hole on the shutter blade and…
Here is my first attempt at correcting misalignment of the PVC blades of my blinds. I needed to keep them aligned in order to not grind the mounting screws of my newly installed Avosdim solar conversion kit . TL;DR it did not do the job,…
This model helps attaching a Bluetooth shutter to the X axis of the Elegoo Neptune 3 Pro . By using the gcode modifier for timelapse in Cura, one can create cool timelapses of prints without the printhead obstructing the view. An…
I had one broken end stroke so i made a replacement, it is sized to let through the original 6 mm bolt and fit the relative nut inside (all quite comfortably) I used petg and 100% infill since it was the toughest stuff i had around and by…
The Coralboard is built for vision that stays on the device. In practice that means a camera on a short ribbon cable next to a bare board. Coral Eye puts both into one small body that looks and handles like a camera. Point it at a desk, a…
Made for any normal drill it is plastic so be gentle but it holds up really well in a drill.
It is made to maintain the shutter box from an other project onto a tripod. It is print in place, with supports. It uses an M6 nut (minimal length is 16mm) and a butterfly nut. Pipe / Tube diameter is 28mm.
This is case was designed to embed all the components needed in the making of a camera shutter by @jamesskelton. Link to his github project page : https://github.com/hackaninstant/Servo-Shutter The box embed : two 3,7v lithium battery for…
Wydruk około 0,18 €–0,23 € nettoWstępna wycena jednego wariantu
Habe die Lamelle für ein kleines Rolltor für den Modellbau verwendet. Gedruckt aus PETG
Use this small cover to avoid accidentally pressing your Kodak Ektar H35N's shutter button. Might also fit the regular H35 (not tested). Slide it on the corner where the shutter button is, and it should stay in place by friction. If you…
Disponible avec ou sans rebord ------------------------------------------ Available with or without rim
This is a replacement shutter button for the older form of Primoflex, from Tokyo Kogaku, that has a central shutter lever placed below the taking lens (not the later model with the shutter button on the bottom left when looking at the…
Introduction This design offers a completely new large format camera shutter, building further on this previous design. It offers a number of improvements making it a more practical, ergonomical and reliable tool. The most notable…
Printing tips: Print 2 bodies (the plain is compatible with the outlined) and 2 shutters. Use holographic plates to give it a nice, extra touch (check the last cover photo for example). Optionally engrave it with a text in the slicer…
Lomo 38mm lens(from LCA120&instant glass) to No.0 shutter conversion
In the house of a friend of mine, they have a shutter at the entrance as a divider. They want to add some hooks without making a hole in the wood, so I came up with this idea. You can print it in PLA or PETG. Support is needed only for…
A remix of wisestones shutter box to make it more space efficient. Part List 2 m3x8mm machine screws 2 m3 nuts 30/01/2026 V1: Reverse engineered wisestones shutter box in inventor and made it more space efficient. 31/01/2026 V1.1:…
Replacement housing for Selve strap coiler with a distance between the mount screws of 155 mm. The original product is listed as 084801/084803/084805 (white), 084841/084841/084841 (brown), 084851/084853 (cream), 084861/084863…
This is a custom-designed adapter to mount a SwitchBot BOT onto a YKK AP shutter remote control . It ensures the SwitchBot's pusher is perfectly aligned with the "Open" button for reliable operation. Key Features: Screwless Design: No…
I recommend putting somekind of brush inside the hole. you can glue it. otherwise wind will still go through. kudos do the original designer it's pretty good and solves many issues. also commercial solutions that are the same cost 100…
Hi, I had a Polaroid 636 Closeup camera that didn't work and when I've shaken it I could hear something moving inside and the shutter button felt like it was doing nothing when pressed. So I opened it up and I found out that the shutter…
I used Petg. something that can withstand the direct sun with a little give.
I created this shutter mounting rail to repaire a broken shutter outside my home. Super glue to the back of your shutters and drills holes as needed for mounting. Enjoy!
This model solves the issue of not being able to fire shutter speeds faster than 1/60s on the Nikon F3 while the camera back is open. This is particularly useful when trying to measure shutter speeds using a shutter tester that requires…
A replacement for missing or broken shutter button for Minolta AF-Tele 35mm Film Camera. This design makes use of a 4mm diameter spring to keep the button pushed up. I took a 4mm diameter spring from a ballpoint pen and cut it to be about…
When we renovated our bathroom, the tiler simply tiled right over the roller shutter strap outlet. Of course, there was no replacement part available for something like that. The hole in the tile measures 30 mm by 30 mm. It stays in place…
Edit 26-01-2026 I have recently developed a new and in many ways better shutter design which I recommend over this version. It does require a few more non-printable components but it may be worth it to many users. It can be found over…
Wydruk około 2,60 €–3,17 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Sunshade (window shutters) crank holder bracket, however, this is also s general bracket/holder for a stick of approx 16mm in diameter.
A cover broke and I have rebuilt the part. There is a model with offset holes for the screws and one with parallel holes. --- Eine Abdeckung ist gebrochen und ich habe das Teil nachgebaut. Es gibt ein Modell mit versetzten Löchern für die…
Since I bought lot of shanel 5 shutter, the Japanese No.5 shutter, and haven't found detail data. I make a simple summary of this shutter. Shutter models There are three models 5A, 5B, 5B-S. 5B and 5B-S have aperture while 5A haven't.…
Just a replacement part for my broken roller shutter stop. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.20 mm Infill: 60% Filament: Geeetech ABS white Notes: Use 5 perimeters Category:…
This is an adapter ring that allows for a Fujinon SW 125mm 5.6 aperture medium format lens to fit the appropriate lens cone and board for the chroma six 17 camera. I received mine and the shutter isn't what was recommended so the lens…
Recreation of rolling shutter end stop for the type shown in the pictures. Repair/Swap broken ones Go fancy with your color choice Mounts using an embedded M5 nut. Use the Jo Prusa method and pull the M5 nut into the recess on the base of…
A pencil case with a sliding shutter door! Snap - No glue needed. Requires accurate printer. Walls are 3mm thick.
Had to replace a broken window shutter holder. Since it was weekend and I didn't know the name of this thing, I just constructed one on my own in openscad. I included the source, but it is really a simple thing and not very elaborated. I…
A pencil case with a closing shutter box case and an inside that can be glued in to hold pens, pencils, and other stuff.
Hello guys, I made simple inserts for “ A1 & A1 mini shutter release holder for camera” from https://www.printables.com/model/979917-a1-a1-mini-shutter-release-holder-for-camera I needed to place a smaller switch than the design…
An easy print, parametric hinged privacy shutter for web cams. See photo for defined variables to adjust. Included .stl file example is for Logitech CrystalCam C920. Layer height 0.15mm Infill 15% Perimeters: 3 No Supports Includes…
ENG / DEU we bought an old caravan to restore it. The caravan has 4 windows that can not open, so these don't need a net and shutter. So we decided to buy cheaper shutters from amazon. These Shutters have a very heavy bar that wobbles…
Quick print glasses for New Year's 2022! Remix Info Primary new thing here is the filament hinge inspired by one of the shutter shade remixes. The original openscad design was really good but the snap-fit arms were very fragile. I used…
Made for any normal drill it is plastic so be gentle but it holds up really well in a drill.
Designed these as I ran out of washers for my hurricane shutters, so I designed these! They work just like regular shutter washers. These perfectly withstood the winds from Hurricane Milton printed with PLA @100% infill. NOTE: ONLY…
A coffin-shaped case with a sliding shutter door! Options Plain Crack Web Bat Printing All parts can be printed without supports Shutter can be printed flat or vertical, but flat is recommended Assembly If printing the bat case, glue in…
Based on my euro modules , this version is designed to hold a shuttered LC coupler. There are two design variants so you can see which works best. The shutter is removed from the fibre module, which then clips into place. The shutter can…
I got a fujifilm instax mini 11 as a christmas gift. The buttons included with the camera did not stick on the double sided tape they came with, so I fired up Fusion360 and after 30min of modeling and 10min of printing I got this. Because…
I bought a few venetian blinds for my windows and some of them didn't have the “no-drill” brackets to install them, so ended up printing one. It works for almost every type of blinds/shutter and has been tested with length of 1.5m and a…
Adjusting Pin for Roller Shutter Motor Adjustment Tool Tubular Motor
It is made to maintain the shutter box from an other project onto a tripod. It is print in place, with supports. It uses an M6 nut (minimal length is 16mm) and a butterfly nut. Pipe / Tube diameter is 28mm.
This is a combination of Hackaninstant's battery compartment for his 4x5 back conversion and his Arduino-based manual shutter speed conversion. All credit for the original design and concept goes to him! The guide to convert a Packfilm…
Remixed the original to accommodate a 90mm LED ring light, as well as allow me to still use the privacy shutter I already had installed on my C920. Created some diffusers of varying thicknesses to make it less blinding, printed in…
Quick print glasses for New Year's 2025! Remix Info Primary new thing here is the filament hinge inspired by a different shutter shade remix. The original openscad design was really good but the snap-fit arms were very fragile. I used…
2021 Shutter Shades designed from @drjames excellent Customizable Shutter Shades Snap-on temples! OpenSCAD source files! Guaranteed fun! Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill:…
This year's shutter shades re-design! Snap-on temples and an easy-to-print design - let's goooo 2022! HT to original design by @drjames: https://www.thingiverse.com/thing:1603773 Category: Glasses
Bitcoin Shutter Shades! Perfect for any bitcoiner to celebrate Bitcoin's journey to $100k. Simple assembly: just print the pieces, snap them together, and secure them with a bit of raw filament.
hi guys this is a fully functional shutter/ iris. you can use it as a desk trash door or something. you can choose how to use it, but use it wisely. have fun you need 12 “pin” and 12 “SHUTTER 12”
I needed to rebuild these holders because the ones in my house started to disintegrate after a few years of sitting in the sun. Print in PETG to hopefully last longer in the sun.
A shutter with individual blades for the 55mm Spotlight “Theo” from Northlight. The blades should be printed with 100% infill to not let any light through (Unless that is a desired effect). There are two versions of the blades 3mf file.…
Softauslöser (AR-1) für die Nikon Kameras mit Außengewinde um den Auslöser. Getestet an S2, SP, F und F2. Wie stabil der Softauslöser ist habe ich nicht gestestet, aber er funktioniert. Eventuell mit einem stabileren Material als PLA…
Habe die Lamelle für ein kleines Rolltor für den Modellbau verwendet. Gedruckt aus PETG
Double the bling! Only the top/surface four layers are colored to speed up the print and keep more strength. PrusaSlicer PROECT with modifiers, set to your desired colors: ASSEMBLY: Use a short length of filament to attach the arms to the…
This is an extremely simple optical beam shutter, driven by an Arduino Nano. It allows precise blocking of an optical beam (the servo can operate at up to 2 Hz). This device is ideal for optical chopping at very low frequencies or for…
This is a slim (1.2mm thick) camera cover that can slide over the lens of a laptop or tablet webcam to ensure your privacy. it should fit most laptops unless they have a very narrow top bezel and is thin enough that it should not…
A small adapter to install on a lubricating spray, to lubricate the slides of your roller shutters.
These models are provided for reference only. Adjustable according to the size of the lens.
A gear meant as a replacement for the sectional shutter gear made by Bulthaup. I've printed two of these with black ASA, but I think PETG would work fine as well. The original material is some kind of hard plastic that turned brittle and…
Designed for Componon-S 90mm F/4.5 HM with polaroid MP4 shutter. should also work for most SK v38 lens
Warning: photo equipment repair common sense required! Disassemble stuff at your own risk! There are springs and miniscule screws that hate humanity are very easy to lose. You need photos or photographic memory to put it back, so take…
Copal & Seiko Shutter Universal Label Print in A4 for later type copal shutter Update 260603: Add seiko types
Copal & Seiko Shutter Universal Label Print in A4 for later type copal shutter Update 260603: Add seiko types
Holga 120 Replaceable shutter button Print any color you like Category: Camera
This is a cover plate for belt winders (roller shutter). The screw distance is 136mm. Print a new one when the original has got a bad color change due to sunlight. The available colors dont fit, print it yourself in your desired color.…
[FR] Ce boitier permet de créer une commande murale pour un volet solaire Vélux. Il transforme la commande radio en télécommande wifi et avec l'ESP8266 il ainsi intégré sous Home Assitant: Tutorial dispo ici :…
I've been searching two days and I couldn't find any holder for Creality 3 V3 KE. I try put different side of x axis but this location is much better stability. I added g-code to creality print "Layer Change G-Code G91; G1 E-10 F1800; G1…
The VFMoto Shutter Tester is an excellent tool for the amateur photographer to test shutter speeds of old film cameras. One challenge in using the tool is that we need to hold the constant light source directly in front of the lens while…
This is a holder/mount for a Wahoo speed sensor, specially shaped for the profile of a DT Swiss (rebranded Shutter Precision) PL-7 dynamo hub. I attached a patch of 2mm self adhesive EPDM-Foam to the bottom side of the sensor to help…
Replacement parts for old PVC ones Caracteristics: Length: 24mm Diameter (base): 22mm Diameter (top): 20mm Threading: M6 M6 Countersunk Phillips washer Print Settings Supports: No Resolution: 0.2mm Infill: 20% ------ Happy Print to the…
Material PLA or PETG Layer high 0.2 / 0.3 → Doesn't matter Infill 15% After printing just put the holder inside the base from the backside.
This roller shutter stop angle bracket is designed to safely and securely limit the end position of a roller shutter. Perfect for repairs, retrofitting, or custom window accessory solutions. Benefits: Strong & durable : Robust…
Exact copy of an existing roller shutter, picture shows the original on the left, model on the right, bolt holes spaced 22,5mm, can't buy these anymore and one broke so I recreated this
Bird Barrier designed to prevent birds to build nests on top of roller shutter cassettes. For the intended purpose see the included picture. They are to be attached using double sided sticky tape. Dimensions 125 x 114 x 27 mm…
Servo: GS-9025MG Fan: 30x30 Rain screen: https://www.printables.com/model/1249057-rain-screen-for-ventilation-shutter
Rain screen for ventilation shutter https://www.printables.com/model/1249012-servo-ventilation-shutter
This gadget is really helpful to rec and stop video or taking a photo handsfree. I've adapted Bluetooth Shutter Switch into a foot switch box. So you may Rec and pause (or stop) your video or take a photo handsfree. You need only below…
Don't let the number of files intimidate you, you'll only needs a fraction of them - continue reading and you'll see why there's that many ;) A riser with rolling shutters. It'll provide the best possible airflow while remaining as…
This is a slim (1.2mm thick) camera cover that can slide over the lens of a laptop or tablet webcam to ensure your privacy. it should fit most laptops unless they have a very narrow top bezel and is thin enough that it should not…
Push-on adapter with 37mm filter thread for my almost 100 years old camera :) on't know how useful will it be for anyone else but I wanted to share anyway. The lens barrel is ~37mm in diameter. It might fit other lenses with same…
This is a 1:12 scale model of my real existing shutter cabinet. Designed as a double cabinet (like the real one) or as a single cabinet. The matching desk can be found here:…
Bonjour, Collier de fixation type Espagnolette pour volets battants Base: 45 mm Entraxe trous: 35 mm Diamètre intérieur anneau: 14,4 mm Diamètre extérieur anneau: 24 mm Épaisseur: 8 mm PETG ou ASA Imprimé en position horizontale Hauteur…
In building various long-standing LED projects on breadboards, it would be nice to lock out the on-board LEDs that are ever present. This slips over a USB Micro or USB-C Arduino Nano, with or without the ICSP pins installed, obscuring the…
The adapter makes it possible to fit standart cable releases to various TLR, Leicas and old Nikon cameras. The threads are very fine. Print the adapter at leas with a layer hight of 0,1mm. If you can, print it even finer. The adapter is…
