Liczymy pasujące modele…
Tested different V-slot covers available on this site, as you can see on the makes on my profile, this was the best fitting cover, has a very good press fit but is still easily removable. Available you'll find a file containing every…
Druckt das Ding im Bereich des Blasrohres maximal mit 0,1mm Schichthöhe. - Da es da lediglich 5° Steigung hat. PET oder besser… Zur Not hilft etwas Alufolie gegen die Hitze. Pumpt bei heißer Nozzle immer etwas Luft (15..20%) durch die…
My Sovol came with almost the same exact tool kit as the Ender this holder was designed for. It also came with tweezers, a spatula, two nozzle cleanout wires of differing diameter, an additional open end wrench, and a 90 deg 6mm wrench. I…
Print as oriented and clip into place. Note that the version in the photos is very slightly misaligned, but that issue has been corrected in the finalized model (but it works well enough for me so I didn't bother reprinting). Original…
Kleine und große Schale am besten aus PLA drucken, da das gut aufeinander gleitet. Etwas Silikonspray (Blattglanz) hilft auch gewaltig. Um die Innenschale dann etwas Nachrüst- Fensterdichtung kleben und in die Außenschale quetschen.…
This cable chain ( SPINE ) supports the extruder ribbon cable on the Sovol SV06 3d printer and stops it from sagging on taller prints. There are three special pieces for the ends of the spine. Refer to the pictures for correct placement,…
This is version 2 of my original SV06/SV06+ heatbed cable support design. This variation is a one-piece cable support and it's super easy to install. No tools are needed, and you do not have to remove any parts. Once mounted, insert the…
Designed for GDSTIME GDB5015 24V. Unobstructed homing. Printable without supports. Light weight. Glueing optional but advised for better and quieter airflow. CFD analysis included. Version improvements: Aditional mounts on extruder…
SVO6 You need 2 x 173.5mm in length each to fill each groove (a ~1mm gap will remain). Scale the length if you need to. SV06 Plus I'm told by user @ThomasAlbrecht that to cover both extrusions fully, you need 4 x 223mm. SV06 Plus ACE I'm…
If you own a Sovol SV06 3D printer, you know how important it is to keep the bed cables secure and protected. That's where the SV06 strain relief comes in - with its straight and lifted versions, it helps to prevent the cable from rubbing…
PrusaSlicer profiles made specifically for Sovol SV06 Plus (SV06+) 3D printer, to make the most of its size, speed and accuracy. Version 1.10 update: profile for SV06 (non-Plus) also included - based on Prusa MK3. The profiles are based…
Later edit: For the US folks https://mandalaroseworks.com/products/sv08-clear-acrylic-panels if you use code CN3D at checkout you also receive a 5% discount! thanks to Mandala Rose Works you have to chose if you use a top hat or not to…
Printable without supports. Designed for GDSTIME GDB5015 24V. Unobstructed homing. Complete replacement for stock extruder cooling. V2: lighter design. Fixed cracking issue at screw hole. Requiered Hardware: 1x M4*20 1x micro JST plug…
What is this? This is a mount for the BTT Eddy for the stock Sovol SV08 toolhead/shroud. Please note: The BTT Eddy needs to be removed from it's casing to fit. Why another/different mount? I had to remake the design because with me the…
This is a very easy-to-print, easy-to-install SNAP-ON back cover for the SOVOL SV06 3d printer. To install, simply disconnect the ribbon cable from the LCD controller board, snap the cover in place, re-connect the ribbon cable, and you're…
WARNING: Calibrate shrinkage before you print. These are long pieces and errors will show. Hello guys I want to share with you that Funssor is selling our design so who want to buy this Top Hat already Printed with all the Hardware you…
Github now: Sovol SV08 - Optimized G-Code / Macro.cfg / printer.cfg and highspeed settings PETG Further releases and instructions on GITHUB: https://github.com/kampfwuffi/Sovol-SV08-Optimized-Macros HOW HARD IS IT TO IMPLEMENT? Basically…
Update! -- November 29, 2023 I have recreated my remixed frame strain relief support model from rogerquin's original model using OpenSCAD ! By default, the recreated frame support is the same as before. However, the OpenSCAD model…
27 June 2025 Here are the latest updates! Xenomorph OG The LED's are moved to the front and the air duct are bigger and also they have Vortex generators. this is adding 10% more airflow resulting in better part cooling. 2 May 2025…
UPDATE: Version 3 included with better tuned dimensions and fixes based on feedback. UPDATED UPDATE: Thanks to Crosslink for featuring this in his video!! The extruder on the SV06 can get quite hot, due to the weak stock fan, especially…
Keep an eye on your Sovol SV06 extruder movements with this extruder visualizer/motor knob that adds a touch of style and personalization to your printer. With the extruder movements on the SV06 and SV06 Plus often difficult to see, this…
Helps you to put on your bed correctly
You can Import my SOVOL SV07 Profile to print fast and with the external fan. The only part I copied from Makersmuse was the start of the external fan. When you create a profile for PETG you should remove the external fan cooling and…
Wanted to make a tool storage rack for the SV06 that match the style of the rest of the printer. Has a spot for all the tools that I received with the printer as well as 5 nozzles. Its one piece that printed on the top face. No supports…
Created a filament guide that better matches the design of the Sovol SV06. I will make a better print when I have the right colored filament.
These TPU feet are designed to decouple the BedSlinger from other 3D printers on the same surface by absorbing vibrational energy, helping to minimize machine wear caused by vibrations. Benefits When you place a single printer on the…
This small upgrade solves the problem of the torque effect on the linear block bearing and the quick shifting of the heatbed when homing the Y-axis. I didn't like the idea of the linear block bearing under the bed being used as a stop for…
Please post your makes 😁 Description Easily mount and unmount things off of your printer. Should work with any printer that uses 2040 V-slot aluminum extrusion. I was told that it won't work well on T-slot extrusions. Instructions…
I have printed them in Polimaker Galaxy Black ABS and they are perfect! The chain and the clip can be printed without support but the ends will need support. Note: if you have bed adhesion problem when printing the clips you can rotate…
A support for the Sovol SV06 Plus cable which runs from the control board box to the print head. On my unit the metal cable support did not extend down in to the control board box, so the support was not firmly guided upwards away from…
A simple heat bed cable strain relief for the SOVOL SV06 3d printer. The 3D-printed piece fits around the cable and inside the existing cable cover. use a zip-tie to clamp the cable in place. Make sure to put the tie head on top so it…
Hello everyone New Version Is here thanks to the community members that helped with the perfect fitment In the Cad you will find all the screws and heat set insert that you will need. for those that don't know how to use a step file i…
If you've ever been in the same room as a Sovol SV06, you'll know that the stock PSU's fan is one of the noisiest parts on the machine. With this simple addition, you can make your printer much more pleasant to be around. It significantly…
This heat bed cable strain relief raises the cable up to a 30° angle coming out from the heat bed and minimizes/eliminates cable contact with the rear frame cover. The most common cause of heat bed cable failure is solder joints breaking…
I am printing ABS on my SV08 since a few months now with absolutely 0 issues (warping etc.). For me, its works fine :) Hope you like it! Please leave a comment and like :) The windows of the doors are 426 (-4/+0) x 166 (-4/+0) x 2 mm. I…
I remixed two designs into this. You will need: 4) M3x8 screws 2) M3x12 screws 1) M3x25 screw with an M3 nut (an M4x25 should also work) If you have time, check out the video. :)
This is a modified version of motocoder's jig to suit the Sovol SV06, the length of cut silicon tube has been extended to 12mm from the 9mm of original jig to better match the Sovol SV06. Information about the original mod can be found…
You can easy print this out of any material. I got an enclosure so i went for PETG. I printed it with the side where the cam is mounted on, on the printplate. You need to replace the two screws! The originals are too short when using this…
My procedure to fix the taco bed on the Sovol SV08... Step 1 Heatsoak your bed to your normal print temp, preform a QGL 2 or 3 times (this will reduce the deviation between the 4 corners), do full bed mesh height map, and save a copy of…
I have added a big version to accommodate for V4 and for Xenomorph with Eddy You need to orient the part in the slicer this is a simple idea not only to keep the belts in place and aligned but you can also stretch them to fit your new…
Update 2022-12-05: Added V2 which is more of a slotted opening tapered to the left and right to account for times when you print something very tall. It gives more flexibility for the filament when the print head is farther away from…
Due to the Heatplate in my DUAL Filament Dryer from Sovol 3D, I made a StandOff for the DryBox. The StandOff has a 20 mm height, to make sure that the Dryer has enough clearance for ventilation. Share your make, that makes me more happy…
This is an original design made by Voron we just adapt it to the top hat that we made for the Sovol SV08 https://www.printables.com/model/865851-sovol-sv08-top-hat You need carbon fiber foam filter 5 pieces of 7mm x 65mm x 130mm You can…
No support, better fan duct for Sovol SV06 PLUS On photos you can see difference between standard and upgraded fan duct. Also check my Sovol SV06 PLUS Cable HOLDER https://www.printables.com/model/482250-sovol-sv06-plus-cable-holder If…
This is a fully printed dragchain-system for the SV08. It is pretty useful when you build an enclosure for you printer to avoid cables at the buildplate. The Drag chain fixed joint and the Under the drag chain fixed joint are the original…
Description : Sovol dryer is perfect but the underside gets very hot. This holder protect the support and help to dissipate heat. re-use original pads hold in place without glue Version : V1 (deprecated): - Perfect for my dryer V2 : - Add…
A simple spool holder for the SV06. I designed this spool holder specifically for the SV06 3D printer, but it might work on others. This spool holder mounts over the existing spool holder. To install, temporarily remove the tube from the…
This is a very easy-to-print, very easy-to-install filament guide for the SOVOL SV06. No tools are required for installation. To install, temporarily remove the spool holder tube and slide the filament guide over the spool holder arm.…
Thank you all, who downloaded this design. I want to also tell you that unfortunately you will need to print the cover again. The small print. I found an issue thanks to all of you who have told me Later Edit : April 30, 2024 Added the…
The best places I’ve found to mount a Pi on the Sovol SV06 and SV06 Plus require drilling and tapping so I came up with this “backpack” concept to clip onto the controller housing. It lightly plays into PLA’s compliance to hold firm and…
One of the mods we are most proud of! this feet they are not just aesthetics they have multiple purpose obviously a fabulous look risers for better ventilation of the electronic part they have the role of protecting the large pulleys from…
I am sending a pre-configured sovol sv08 profiles file materials such as PLA, PLA-SILK, ABS, ASA, PETG you can mosify and experience improvements have fun profiles are in a zip file I added pla wood in the test version, set the speed as…
…Please be sure to hit like & post a make, I'd love to see your prints! Print on its flat EDGE as this will provide the strength you need in this orientation, that's important! Don't print too fast or you could pull it off the bed, use a…
Testing finished, released! Read Design/Testing section below if you're interested in the details. Checked in with Sovol and they confirmed this will also work with the SV05. I find 30-55% fan works well with PETG depending on nozzle temp…
This is just a simple texture and model combination for your Sovol SV06 presets in SuperSlicer or Prusaslicer. All I did was adjust the z position of the stl for the bed and quickly made a texture in Affinity Designer for the texture. It…
This is a slim version for having cable chain on the Sovol SV08 All the part are pre oriented in the best position. Only the cover needs little support, the rest they don't need support and only for the clips if you don't have good…
UPDATE Added v2 (RECOMMENDED) Changelog Easier to tighten. Accommodates: Standard ADXL345. BTT ADXL345/S2DW (see this make ). 3 versions of the mount (see filenames for explanations). The bed spacer now plugs into the mount. BOM 4 x M3 x…
Print with 3 perimeters, 20% infill, use snug supports to the bolt holes. Use M4 bolts and nuts to attach everything together. This works perfectly with the SV08 Filament runout sensor holder from dmika7200 . EDIT: I completely…
Easy manage your cables on your printer with these simple extrusion cable clips.
The Nautilus design remixed to fit Sovol SV06 Plus taller hot end. This will work with stock or volcano nozzles. The model is quite rough and ready, not as refined as the original, but works absolutely fine and printer first try. when I…
…Please be sure to hit like & post a make, I'd love to see your prints! MACROS AVAILABLE HERE…! https://github.com/3DPrintDemon/Demon_Klipper_Essentials_Unified/ EDIT: ADDED SILICONE MOUDLE for use with silicone pads, including the one…
Remix of the cable relief if you have your printer next to a wall 0.2 layer or 0.15 i used PETG for better heat resistance Supports on plate only Remix of Cable Strain Relief for SOVOL SV06 3d printer da rogerquin
***IMPORTANT*** Some users have experienced difficulties snapping the fan in place. Please measure the fan duct to confirm your printing results have the recommended measurements before installing the fan. If your measurements are not…
Adjusts angle of the built-in camera so it points down more (centered a bit below the nozzle). I recommend using Arachne wall generator to handle the very thin loop. Category: 3D Printer Parts
Improved dimensions. See Sergiienko Valentyns original for more details. If you use Polymaker PolyMide CoPA like me: Printing it all in one piece with supports is an option, but the supports are a struggle to remove as is default with…
Sovol SV06 Plus is a great printer, but its bed heating cables are not fixed resulting a safety issue. With this solution first 20mm will be fixed. Don't forget to print it from ABS or other hi-temp material. Installation requires 10…
Note that this model has been superseded by this new test square. I find it easier, as well as being faster, covering a wider range of nozzle offsets, and having a finer resolution. This is a test print to help fine tune a printer…
I printed this in ABS with 4 walls and 40% gyroid infill Required: 4 x M3 x H4 Heat Inserts, 4 x M3 x 20 Bolts
Designed for GDSTIME GDB5015 24V. Unobstructed homing. Printable without supports. Light weight. Glueing optional but advised for better and quieter airflow. CFD analysis included. Version improvements: Aditional mounts on extruder…
Simple bowden tube mount for M6 bowden coupler. Requiered Hardware: 2x M3*8 countersunk 1x M6 bowden coupler
New versions available: Single Fan: https://www.printables.com/model/542760-the-nautilus-sovol-sv06-fan-duct-5015-blower-fan-v Dual Fan: https://www.printables.com/model/543502-the-amonite-sovol-sv06-fan-duct-dual-5015-blower-f Designed…
This is a desiccant case for the SH02. It can be used with silica gel larger than 1.5mm in diameter. NOTE: Please print it in 0.15mm layer height without supports. Added 1.0mm gap models too(January 20th , 2025)
This is a remix of the excellent cable chain for the Sovol SV06 made by rogerquin ( https://www.printables.com/model/447467-cable-chain-spine-for-sovol-sv06-3d-printer-extrud ). To make the chain flex smoothly, I used blender to scale…
Adapter for Hotend Bambulab. Print in ABS, ASA, ASA-CF, PC-CF, not in PLA or PETG. 3 possible choices. -The original Bambulal version with fixed nozzle. You must print the BBL-O version. -The AliExpress clone, with the tiny nozzles…
Made from scratch, just few additions to the original to make it easier to print with ASA, ABS… and with bearing of course. Added clearence for the rod hole to prevent pushing down your motor mount when tightened 2 models : Standard With…
A cable chain to keep the heat bed cable from dragging along the base of he printer. Should help with the thermistor going haywire. Notes: ORIGINAL version. Thick. Does not fit with a back mounted parts cooling fan! The shroud “parks” on…
This is a direct replacement for the stock front cover of the Sovol Zero and Sovol SV08 Max toolheads. Besides improving part cooling performance, it also adds support for a dedicated toolboard fan (2510 size). We tested the part cooling…
Description When I printed my first large model on the SV08, my Nozzle clogged multiple times. I may be wrong, but my assumption here is that it's not a great idea to enclose the hotend heatsink in a plastic shell, thus killing any kind…
Didn't like the giant printhead housing on my sv07+ but I still wanted to use the factory led for it so I whipped up this bracket on tinkercad real quick to try out, at least until someone comes up with a better one lol added a 2nd model…
If you like it feel free to leave a comment or even better,buy me a "coffee": https://www.buymeacoffee.com/redangel1984 If you are looking for bracing/stiffener for your printer which uses 2040-AluminiumExtrusions for the frame, look no…
Relieve rubbing of the cord on the table, corner and frame. Keep cord parallel to the bed movement. Presses onto cord no fastening required.
here you can find the last version https://www.printables.com/model/938796-sv08-cn3d-shroud-v3-extra-fan-magnets-klicky-led After making some tests we are glad to share with you the V2 Shroud The version 2 is using 2 more magnets to…
If you need the bed and the bed texture for your slicer here it is I took the real bed shape from the open source files of the printer and left the lower block as well for a more consistent base I made it for PrusaSlicer but should work…
Tired of plastic debris getting into your Z motor pulleys? Oh, didn't know that was a problem? Small bits of plastic from printing will make its way into your Z motor pulleys and fill up the teeth. This will cause stretching of the belt…
These are just simple blocks you can shove behind your Z axis motors on the bottom side to true up the angle with the metal uprights. See photos for what I'm talking about. I noticed mine were greater than 90 degrees and this seems to…
This bracket mounts the SV06 Plus filament runout sensor directly above the hotend, allowing it to detect runouts much closer to the extruder. The mounting hole on this bracket has been molded perfectly to accommodate the runout sensor,…
Install this simple little widget to stop your extruder's idler pin/shaft falling out while printing & causing serious extrusion issues as seen in the images below on SV08 OG, SV08 MAX & SV ZERO printers! I know there's a few out there…
May I present the arch villain to all of your heroes, the bad guy dressed in black. NEMESIS! Enjoy! edit: New inductive probe version & heat insert version included for E3DV6 systems. NOTE a firmware change is required to use the…
…Please be sure to hit like & post a make, I'd love to see your prints! Add a highly accurate M12 LJ12A3-4-Z/AX inductive probe to your SV08! This probe is a NPN NC probe. This means it is normally closed & will provide a “low” signal…
Designed from scratch to improve parts cooling. -No supports needed -Uses stock blower fan -Uses (8) 4MM x 2MM magnets https://a.co/d/jkjbcDB -Optional dual 25x25 fan mounts for breakout board https://a.co/d/fANaU6A Upgrade your print…
Check out my other models :) Update 10 : Add a Honeycomb Top with 50mm Raiser Update 9 : Add 2 Tops for neo2478. Must be glued together. a normal one and a lite version for less filament needed. UPDATE 8 : Add a Honeycomb decor doorframe…
This is the all new Vortex System to mount the Biqu H2 V2 extruder on the Sovol SV01 PRO, OG SV01 & SV03! Equipped with twin spiralling air ducts for powerful effective airflow directly to the area below the nozzle! . EDIT: Now with V2…
This tool organizer for the Sovol SV06 Plus is designed to snap onto the top of the vertical extrusion that the power supply is mounted to. It is a snug fit and will require a little coercing. The idea was to house all of the tools needed…
Cable Chain für den Sovol SV04. Folgende Teile werden benötig: 1x Bed_Connector 1x Frame_Connector 29x Cable_Chain_Link 29x Cable_Chain_Link_Cover Original Heatbed Abdeckung abnehmen siehe Bilder. Ebenso den Kabelbinder entfernen. Den…
Update 9/3/2024: I don't have this printer anymore, so upon request I am posting the CAD files for this project. Fill free to continue the work with this mount/duct with attribution. Also changing to CCA. Update 6/15: Added a dual screw…
Hula Sovol SV08 Feed Adapter for Hula Credits to the original project of ThrutheFrame who made the Hula Project. This models fits to the Hula for Voron. Please read that manual for more informations. Slicer Settings • Wall loops/perimeter…
Keep your Sovol SV06 or SV06 Plus extruder cable elevated with this cable support! This model was created in OpenSCAD . The default curve angle of 60° is customizable in the OpenSCAD model. Recommended pairing This model pairs well with…
I took the factory hotend mount model and remodeled it to accept the X gantry Voron Clockwork 2 left and right mounts. Since the SV06 has its own probe and uses sensorless homing I removed unneeded geometry for belts, probe mounts etc.…
I was concerned about heat for this Sovol SH02 dryer at the hottest temperature so I made a riser. I kept it open as I wanted airflow underneath. It simply inserts over the existing feet (with decent tolerance so you won't have to worry)…
Test your bed-mesh and z offset. Use your preferred slicer and settings. Voxelpla fire orange filament
