Counting matching models…
[update] I added a new version “trayStackerShort” which doesn't extend as deep into the tray. This is useful when freezing liquids so the stackers don't get stuck and it prints faster.[/update] These have been confirmed to fit trays for…
Print approx. €4.07–€4.98 excl. taxPreliminary estimate for PETGSource material: PET
Stock, the oculus quest does not fit me very well. If I pull the band low enough to keep it from slipping off, there is a huge gap at the bottom of the headset. This allows me to have a very good fit with no gaps and keeps the headset…
Print approx. €1.16–€1.42 excl. taxPreliminary estimate for PETGSource material: PET
This is a fridge magnet with a captured dial that can be used to keep count of anything you want to track. Print two to cover 0-99, etc. There are two versions. One large one that takes a 1/2" x 1/8" magnet and a smaller one that takes a…
Print approx. €0.62–€0.75 excl. taxPreliminary estimate for PETGSource material: PET
The mechanical emergency door release on the cybertruck is hidden under a rubber insert in the door pocket. This makes it very unlikely to be found should an accident render the electronics unresponsive which could be deadly. This model…
Print approx. €7.93–€9.70 excl. taxPreliminary estimate for PETGSource material: PET
Snaps on the Quest2. Push forward to reveal the power button when you mean to press it.
Print approx. €0.20–€0.25 excl. taxPreliminary estimate for PETGSource material: PET
Nice use of space in the door. Both the bin and the lid require supports. I highly recommend using PLA for the support and PETG (or ASA) for the body since this leaves a nice finish without any need for sanding or other post-processing.…
Print approx. €5.18–€6.34 excl. taxPreliminary estimate for PETGSource material: PET
Print at 0.2mm layer height with no supports. Default PETG Prusa profile works great. This is an improvement of my original design: Improved grippers for comfort (fingers rest closer together) Beefed up hinge Tightened tolerances for a…
Print approx. €1.36–€1.66 excl. taxPreliminary estimate for PETGSource material: PET
Extra clips in case you lose some or just want to secure it better. I found that having two more (six total) works well - two on the front edge and two on the back edge since those edges bow a little. Print instructions 3 perimeters no…
Print approx. €0.39–€0.48 excl. taxPreliminary estimate for PETGSource material: PET
If you already installed the drain hose plug , and want a matching cover of the unused hole, this is your huckleberry. A bit tight to snap in place but at least you know it won't pop out. If having difficulty, you can try a 0.99 scale…
Print approx. €0.30–€0.37 excl. taxPreliminary estimate for PETGSource material: PET
The only change I made from the standard 0.2mm structural profile was to increase the perimeters to 3 to give more support to the screws. Line up the T-slot nuts within 1-2mm of their holes before installing. Screw each in loosely so you…
Print approx. €3.46–€4.23 excl. taxPreliminary estimate for PETGSource material: PET
Refrigerator magnet with a captured dial to help keep track of daily tasks. Has two indexes per day which can be useful (such as keeping track of if you have already had your second cup of coffee). There are two versions. One large one…
Print approx. €0.60–€0.73 excl. taxPreliminary estimate for PETGSource material: PET
I keep the bucket on the counter while collecting scraps. I wanted a lid to hide the garbage and prevent attracting flies, etc. The skirt does go outside the print surface on a MK3 and you get warnings about that during slicing but it…
Print approx. €8.66–€10.58 excl. taxPreliminary estimate for PETGSource material: PET
When I saw the Veronoi vase design by mikecore69 . The Cholla (jumping cactus) skeletons you find in the desert came to mind so I decided to make a version which highlights this. Place the skeleton first, then add the flesh to it.
Print approx. €24.64–€30.11 excl. taxPreliminary estimate for one variant
I found almost immediately that 1mm was too coarse for an object I was modelling so made another with 1.5, 2.5, etc. to go with my prior gauge ( https://www.prusaprinters.org/prints/148347 ). Print at 0.2mm layer height. Depending on the…
Print approx. €0.93–€1.14 excl. taxPreliminary estimate for PETGSource material: PET
This is a precision 20mm XYZ calibration cube which improves on the typical calcube. There are two issues with the typical cal cube: 1) Hard to make an accurate Z axis measurement because either you have error from the squish of the first…
This is a tray to hold a pair of glasses out of sight behind the touchscreen. Snaps into place on the mounting arm. Print instructions Category: Automotive Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter…
[update] I created a new version ( https://www.printables.com/model/663843-improved-harvestright-drain-hose-plug ) that helps maintain a good drainage angle better. You probably want that one. [/update] Didn't like the hose just resting…
I added slots in the back so it can rotate back after one of the pins is removed (leave locknuts off) to facilitate loading filament. This is technically a remix of the OEM Prusa buffer but I could not find a way to point to Prusa's own…
Certain times of the day, our south-facing garage door will not close due to the sun shining on the obstruction detector creating a false detect. This model snaps into the standard mounting hardware for a Chamberlain garage door opener…
This is a split fender design with the fenders made very short. I like to ride with my feet very close to the wheel so I designed these so I could easily find the edge of the platform nearest the wheel without having to look down or…
This is a cover plate for the emergency release latch on the passenger side door to help avoid unintended use which can damage the door trim. Recommend printing in PETG or other high-temperature material. For single filament printers you…
Improved version of the drainhose plate in response to suggestions from @PTech . Hole is lowered and angled to avoid water collecting in the tube. You may also want the matching cover for the other side .
Tool holder has clearance for belt clips. Battery holder includes retention mechanism so batteries can be stored any orientation - even upside down. Both models print as oriented (standing on end) without supports.
Update: This part was recently changed. If your extruder was manufactured after February 2021, you should use the 2021 version. Earlier printers will have to use the other. I found it very difficult to set the very sensitive extruder…
This is a custom mount for the MMU2 which holds it horizontally. It is also higher to allow for clearance of the extruder when printing tall prints. I use this along with my angled buffer mounts to create a low resistance path from spool…
[Update] If you have a newer model with the extra (5 total) trays you will want this version [/Update] I found it very annoying to have a bunch of water drip out of the trays after drying - forcing a second dry before storing. This also…
Includes radius's from 1mm to 10mm. Note that I added a chamfer to ensure squish of the first layer doesn't compromise the accuracy so ensure you keep the tool square to the object being measured and use the center of the tool (not the…
This is a set of functional shop goggles designed with a steampunk theme. It hold six lenses per eye in groups of three enabling filters to be used along with magnification, prescription, etc. Print instructions Category: Tools Print…
I sliced this version up into parts so it could be printed on a multi-color printer without supports. Original here: https://www.thingiverse.com/thing:2085990 Print instructions Category: Games Print Settings Printer Brand: Prusa Printer:…
Inspired by two of my favorite designs: the finger chopsticks by calvindonger and the bag clip by neoyarus , I decided to make a single device that combines both functions. This is the result. Can be used to clip the bag of your favorite…
This is a foot with a built-in oil moat to go under a beehive to block ants from gaining entrance. There are two versions. The original and a second with a side port for adding the oil (it makes it much easier to fill). Print instructions…
Found it very annoying to have a bunch of water drip out of the trays after drying - forcing a second dry before storing. This also holds them better - preventing them from falling or sliding down. Designed to fit the five trays of the…
This is for the Rift S and Quest controllers - will not work with the original CV1 variety. If you want a stand for those, it is here: https://www.thingiverse.com/thing:1969167 Print instructions Category: Toy & Game Accessories
[Update] On request, I have added two additional versions with a cutout for after-market camera sprayers. Those have the _wash suffix in the filename. [/Update] Supporting 4x8 plywood requires leaving the tailgate down which points the…
The Cybertruck HFS exterior is amazingly tough. Can withstands handgun bullets and even C4. However, it leaves fingerprints. These are designed to attach to the inside via heavy duty 3M double sided tape and provide a convenient handle to…
If you have a newer model with six trays, I uploaded that version here: ttps://www.printables.com/model/1587701-harvestright-pro-large-tray-drying-rack Found it very annoying to have a bunch of water drip out of the trays after drying -…
This is a great model by @RoccosStuff. In some of his earlier models he used the spare metal pins for the lock bolts but chose to use 3d printed pins on this. I think the metal pins looks better and it is easier to print the rack that way…
Some of my plants are prone to root rot and require allowing the soil to dry between watering. I have a bunch of these to allow me to fill each up and walk away. The water is introduced slowly enough to wick back into the dry soil without…
Cable spool for wall wart. No more untangling wires! Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: Prusa PETG Category: Organization
After printing all parts (and maybe an extra fence or two), glue the three sections of each side together. Take care to keep them aligned while the glue dries - ideally find a flat surface against a wall you can push them against. Once…
The trim pieces work well in PETG thanks to it's toughness (ASA is a little too brittle and can break during install). The covers can be printed in either PETG or ASA (or metal using the vSS variant). The files ending with the _DS suffix…
Often you need to use your real hands and the Touch controllers get in the way when dangling from your wrist. Print two of these and slip onto a pocket or thin belt so you can holster your weapon. Slips in easily if you turn your thumbs…
This is a plate frame with the Tesla Tri-Motor (Cyberbeast) Cerberus emblem. I made three versions: cyberusPlateFrame_noText.stl - for the lucky few who actually have theirs cyberusPlateFrame_comingSoon.stl - for those of us still waiting…
My frames broke so rather than spend another $300 on new frames, I decided to print a new set. This is designed to fit my particular lens shape but I suspect with creative use of the XYZ scale factors and maybe some hot air a lot more…
ASA is a great choice for this due to it's high temperature stability - esp. if you don't have cabin overheat protection on. May need a brim, though. PETG is also a good choice. i printed four, two for each visor, to make it easy to use…
This is a fixture that can be connected to the eight rack connections points so roof racks can be installed and removed more easily. Does not interfere with the flip covers. This must be printed in metal. No FDM plastic part will be…
Helps hold up to four silicone mats for drying after washing. No supports required but you definitely want the nozzle fan running to keep the tips from drooping. You might also be interested in my other models for the HarvestRight Freeze…
Operating the emergency exit lever can damage the window trim so this is a part to discourage casual use while not interfering with operation when needed. It is designed to easily break away so the lever can be operated in an emergency.…
The ratchet mechanism in common use for hanging grow lights work fine as long as the lights are easily in reach. If you have high ceilings and your plants are tall or you have them on a table for ease of access this becomes a problem…
This is a 6 slot version for older machines. If you have 7 trays, you want this remix: https://www.printables.com/model/1587731-harvestright-pro-xl-tray-drying-rack Found it very annoying to have a bunch of water drip out of the trays…
The center console tray on my truck was too loose and would often fall through into the compartment below. This is a shim which attaches via 3M double-sided foam tape and make a nice stable support. There is a 0.5mm lip at the top to hide…
Update: I have a new version which preserves more visibility, is less bulky, and more drop-proof here (but requires a large bed printer): Many trucks have the backup camera on the tailgate which renders it unuseable if hauling a load with…
For an 8x1x16 tang. You might also be interested in the matching dial knob . No supports.
Print upside-right so any droop from the bridge is hidden. Recommended settings: Material: ASA or PETG Layer Height: 0.2mm Top Fill Pattern: Hilbert Curve It is snug and hard to rotate once pressed in place so make sure you line it up…
This is a mandrel to hold filament spools with holes from 30mm through 60mm. You'll need a 1/4" nut and bolt (about 4" long). I designed it so the end mandrel can be removed without fully unscrewing the nut so it can still be used if you…
There have been reports of door malfunction after getting windows tinted due to the excess water used during installation. For this reason it is a good idea to protect the exposed pins on the side mirror connector when the side mirror is…
Cerberus(Cyberus?) Badge on the tri-motor "Beast" Cybertruck
Helps hold up to five silicone mats for drying after washing. No supports required but you definitely want the nozzle fan running to keep the tips from drooping. You might also be interested in my other models for the HarvestRight Freeze…
I made this mount to minimize the resistance in the total PTFE path from spool to MMU. Angling the buffer allowed me to reduce the length of the tubes and reduce the change in direction to a single sweeping turn of 145 degrees. I also use…
Found it very annoying to have a bunch of water drip out of the trays after drying - forcing a second dry before storing. This also holds them better - preventing them from falling or sliding down. Made for the small model - not sure if…
Stand to hold both (original) Oculus Touch Controllers in an easy to grab position. There are two versions: original and one with a recessed tray. [update]If you have a Rift S or Rift Quest, this does not fit those controllers very well.…
Grocery bag clip for a 2011 Nissan Leaf to help keep groceries contained. Fits the rear vent slots. Print instructions Category: Gadgets
This is an insert to level the floor of the Tesla Model 3 frunk so it can be used for pizza/carry out without the toppings sliding to one side. Print instructions PETG or ABS recommended to better handle outdoor temperatures unless you…
Tiefling horns to go with your Oculus Rift. These magical items bestow a +2 saving throw against heat damage. These also impart +2 Charisma when interacting with a Geekubus (but -2 Charisma for all other creatures). The magical effect…
For quilters. A spin on the "Add 1/4" tool which some find just a little more than needed.
Clip to cover the lens to prevent unintended sharing of video. Print instructions Category: Computer
Working with the bed divider: Remove the 5/16 nut on each end and slide out the clamp feet. Be careful - there is a cylinder and spring inside that can drop out. Remove the two side plastic guides and replace with these prints.…
This is a dust/privacy cap for the Oculus Rift sensor. Category: Gadgets
Not to reinvent the wheel but my mother was having a hard time with the other ear protectors I downloaded and printed so I designed this to be very easy to hook the elastic but difficult for the elastic to fall off. She says she likes it…
Allow you to use cheap 3/4" PVC to extend the vacuum reach or add sweeping elbows to get at hard to reach locations. Print instructions Category: Household
For some herbs and essential oils, it is desirable to keep the temperature below freezing to prevent undesirable components getting into the tincture. Since filtering often takes hours, I created this device to allow putting the entire…
Pretty self explanatory. Push the cord through. Tie a figure eight for 1/8" or an overhand knot for 3/16" (both examples shown in pic: 1/8" in foreground, 3/16" in the back). Can be scaled up or down for other cord sizes.
I have skinny fingers and knobby knuckles so the ringsize that fits ends up being very loose and the SpO2, pulse, etc sensors have a hard time getting consistent reading. This is a flexible spacer that can be inserted after putting the…
You might also be interested in the matching plunger knob .
This is yet another filament clip. The angle here, though, is these also provide a means to remember your recipe for a particular spool of filament. Each clip has a number representing a particular temperature or % flow. Simply clip your…
Helps hold the silicone mats up for drying after washing. Works for full-sized cookie sheet mats as well. No supports required but you definitely want the nozzle fan running to keep the tips from drooping. I have other versions that hold…
This is a holder for a Note20 S Pen on a Otterbox defender for a Galaxy S21 Ultra. Uses a 1/4" x 1/16" magnet inserted when it reaches 14.2mm to help keep the pen secured. Maybe add a tiny dot of glue to help keep it in place. Print…
This part is designed to mount a Holosun AP16 507K/407K reflex sight (or any sight using a modified shield mount) to an Ataman AP16 pellet gun. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 0.15…
Like to share your CV1 Oculus Rift but want your velcro to last? Instead of wincing every time a friend rips the velcro to readjust, simply set to the largest setting and use this insert for people with smaller diameter heads. Between…
Shelf that holds up to six Altoid or similar cannisters. Designed to withstand somewhat spirited driving while still being easy to retrieve. Slide down from the top to lock in place.
Inspired by wingspan organizer by @gnollzor : https://www.printables.com/model/1511786-wingspan-card-and-egg-holders Print at 0.2mm layer height. The center piece requires supports. PETG with PLA supports works great.
Wanted an option to hold my inspection Loupe.
This is my third generation virtual reality headset. The primary feature introduced this time is a detachable cradle for the phone. This allows you to quickly remove the phone to switch apps, answer a call, etc. Additionally, it makes it…
I added a second LED strip to the left-side of the enclosure and needed a way to power it. Easiest way was a short connector from the right-hand LED strip across to the left. I didn't really like the cable anchors and zip ties for this…
This is a lid that fits a standard small-mouth mason jar with extra headroom to allow you to store the spreader in the jar. If you want one the fits Crofters Jelly jars, you can find it here:…
I cringed at the thought of drilling a hole in my Tesla to mount the optional front power liftgate button included with the teslaoffer product ( https://www.teslaoffer.com/product/model-3-power-liftgate-soft-closing ). Designed this mount…
Found it very annoying to have a bunch of water drip out of the trays after drying - forcing a second dry before storing. This also holds them better - preventing them from falling or sliding down. Made for the large model based on…
This a clip designed to be used with a Miller LPR-100 half-mask respirator along with a 3M 9100XX Speedglas welding mask. Remove the plastic elastic harness and replace with this. It aligns with the vents in the welding hood to hold the…
Basic Arduino Yun enclosure with openings for USB power and WiFi antenna and hidden Epic Face. Hole matches an antenna I purchased off eBay. Print instructions Category: Electronics Instructions Printed with Slic3r - no supports. Lid is…
I really liked @ignisVeneficus' arrangement here: https://www.thingiverse.com/thing:3460943 I just remixed the STL files for the player trays so they can be printed with the logos in place on a multi-material printer such as the Prusa I3…
Replacement lens cap for the Armasight Core Night-vision Monocular. Print instructions Category: Sport & Outdoors Print Settings Printer Brand: Solidoodle Printer: Solidoodle 3 Rafts: No Supports: No
Printables didn't like the M117 gcode command (it works) so I had to upload the gcode via zip file. If you want to slice it yourself it takes some customization. At the time of writing this PrusaSlicer doesn't support adding color changes…
300mm fan (298mm, actually, to ensure clearance to the fan shroud) with 8mm D shaft. Recommend printing in PETG with PLA supports. Set supports as “soluble” with 0mm separation. Don't forget to change the interface extruder to PLA as…
This is just a minor modification of the awesome design provided by jegstad to provide an air passage when used with the following Oculus CV1 cooling system: https://www.prusaprinters.org/prints/15141-oculus-horns-of-cooling Print…
This is another lid made to fit a Crofters Jelly jar which uses a different screw pitch (18mm/turn; 4 starts). If you want one the fits small mouth mason jars, that can be found here:…
I make extra-wide spools by combining two Prusa Spools ( https://www.printables.com/model/1629497-prusa-spool-doublewide-adapter ) and made this leadscrew to use in my Pastamatic winder for them. You will probably be interested in this…
I had an accessory that required six studs to be held in place. This is a sleeve you can put on the L-Track studs to lock them in place making installation much less of a hassle. There are three versions, a flat version, a thin flat…
Mount for an IR illuminator with a 20mm diameter on an Armasight Spark Core night vision monocoluar. Print instructions Category: Sport & Outdoors
My Juicer is optimized for oranges and larger citrus but leaves a lot of juice in smaller fruit like key limes. This helps squeeze every last drop out. To use just twist onto the existing strainer.
This is a cradle to hold a Samsung Note4 (no case) and snaps into the TTVR modular virtual reality heasdset ( http://www.thingiverse.com/thing:733390 ). It is very important that the corners not lift during print since the dimensions are…
