Search results: 45

Sort order

6,358 models

P
PrintablesKYZ Design

X45 Sprite CR Touch Probe Zero Y-Offset Mount v1.1 (Ender-3 S1 Pro and similar)

Update 25/08/2023 v1.2 added - access for heat break setscrew created, small amount of material added on the fan-side of the grille near the bottom to ensure proper clearance to heatsink fan. Update 11/04/2023 v1.1 added - probe bracket…

Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant

Downloads
3,583
Likes
526
Rating
4.85
P
Printablestm108

Ethernet RJ45 Repair

This is a repair clip for your broken Ethernetcable. You can easy print it. The clip makes it possible that the cable does not always slip out so easily when the clip is broken off at the top. To print: you can use PLA too Use supports

Print approx. €0.25–€0.31 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
1,813
Likes
275
Rating
4.62
P
Printablesbuchnema

Canister Spout with Vent – DIN45 / DIN51 / DIN61 / DIN71

This pouring spout is designed for canisters with DIN threads , commonly found on 10 L and 20 L canisters . An integrated air channel allows air to flow back into the canister while pouring, resulting in a smooth, controlled stream and…

Print approx. €3.71–€4.54 excl. taxPreliminary estimate for one variant

Downloads
1,494
Likes
256
Rating
4.92

.45 ACP Ammo Box

This is a remix of the Rugged Box Parametric by Whitey. This box is designed to hold 100 .45 ACP Cartridges in two removeable trays. The center rib on the box base corresponds to the slots on the bottom of the ammo trays. This allows one…

Print approx. €0.20–€0.24 excl. taxPreliminary estimate for one variant

Downloads
1,159
Likes
211
Rating
5
P
PrintablesJurriaan

45 RPM record (phono) adapter

Based on https://www.thingiverse.com/thing:10475 Remodelled it from scratch using FreeCAD so it wasn't too small. Use a lot of perimeters while printing (I used 6). You can find the FreeCAD file at…

Print approx. €0.16–€0.19 excl. taxPreliminary estimate for one variant

Downloads
1,055
Likes
69
Rating
4.89
P
PrintablesCatja

Belt Clip Accessory for Thermacell MR300/450

Due to a lot of flooding, mosquitos seem to have thrived recently. To both take less space in your gear and make it more accessible, this clip allows you to mount your Thermacell mosquito repellent on a backpack, bag or belt! The design…

Print approx. €0.93–€1.14 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
1,044
Likes
110
Rating
4.89
P
Printablespedrolamas

ADXL345 Bed Mount

I wanted to use an ADXL345 accelerometer to measure resonances in Klipper in my Ender-3 V2 glass bed, but there is no straightforward way to attach it, so I designed this quick mount that will allow you to get the accelerometer aligned…

Print approx. €0.47–€0.57 excl. taxPreliminary estimate for one variant

Downloads
682
Likes
73
Rating
4.5
P
PrintablesSquasherJoe

Canister Opening Wrench 1L - 60L (DIN 45 / DIN 51 / DIN 61, Ø 48 - 58 - 65 mm)

Simple opening and closing spanner for standard 4- or 8-ribbed lids of canisters between 1L-60L volume (DIN 45 thread, Ø48.2mm | DIN 51 thread, Ø58mm | DIN 61 thread, Ø65mm). Turn tool around or use the included insert depending on the…

Print approx. €1.95–€2.38 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
558
Likes
67
Rating
4.88
P
PrintablesTai Tetsuyuki

Dog 45 tours

La modélisation 3D de mon chien a commencé par la prise de nombreuses photos de lui sous différents angles. Ensuite, j'ai utilisé un logiciel de modélisation 3D pour créer un modèle numérique de mon chien en utilisant ces photos comme…

Print approx. €0.75–€0.92 excl. taxPreliminary estimate for one variant

Downloads
475
Likes
61
Rating
4.75
P
Printablesxro

Enclosure for Waveshare ESP32-S3-ETH OV2640 CAM LAN RJ45 POE

This is an enclosure for this board from Waveshare with POE-module and OV2640-camera which you can get on Ali and other sources. not fancy or pretty, but functional, lightweight, space-saving and filament-saving ;P Addons I also made an…

Print approx. €0.58–€0.71 excl. taxPreliminary estimate for one variant

Downloads
464
Likes
24
Rating
0
P
Printablesjlennox

Ridgid R4512 Table saw zero clearance throat plate (R4520?)

This is a zero clearance throat plate for Ridgid R4512 table saws. These may or may not work on R4520 saws? I believe they are the same but I do not own one to verify. Because the print is too large for most printers, it must be printed…

Print approx. €9.84–€12.02 excl. taxPreliminary estimate for one variant

Downloads
360
Likes
52
Rating
0
P
PrintablesLasstcall

1/4 Male SAE45 flare plug

1/4 inch SAE 45 degree male plug for capping refrigerant hoses and other fittings Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 20% Filament: Overture PETG any…

Print approx. €0.58–€0.71 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
343
Likes
20
Rating
0
P
PrintablesPatrik

Gridfinity bins for CR2450 batteries

Gridfinity battery bins for CR2450-batteries. The bins can be stacked. Included bins: A 1x1x4 bin that fits 5 batteries. A 1x2x4 bin that fits 10 batteries. The base box is generated with the Fusion 360 GridfinityGenerator,…

Print approx. €0.83–€1.01 excl. taxPreliminary estimate for one variant

Downloads
321
Likes
21
Rating
5
P
PrintablesSurfalex2000

ROTOR PIN for PLAYMOBIL Rescue Helicopter 3845-A || Rettungshubschrauber

I bought a used Rescue Helicopter, but there was the Pin missing to hold the Rotor Blades. So i made a replacement. Print the Part sideways, so that the print get the Maximum Material stability, and doesnt brake.

Print approx. €0.51–€0.62 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
317
Likes
26
Rating
0
P
PrintablesCatja

Webbing/Strap Clip Accessory for Thermacell MR300/450

While the original clip is designed to be quick-access and multi-purpose, this variant was made to fit more securely onto the straps of most backpacks. The integrated hook and slight ramp makes it a lot harder to accidentally bump off,…

Print approx. €0.95–€1.16 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
309
Likes
62
Rating
5
P
Printablesvolly

Rubber Band Filament Cutter 45°

I love the Filament Cutter 45 from Pomi, but as i try to print it, i found that the needed materials are not as common available as i thought. So i decided to give it a “facelift” with a even easier accessible material: rubber band. Print…

Print approx. €0.35–€0.43 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
278
Likes
63
Rating
5
P
Printableswehrenseb

Small Parts Container / Drawer Organizer 45mm Grid

Small Parts Container / Organizer I made those little containers to organize my screws and nuts drawer. The smallest one is 45mm x 45mm small and the others come in multiples of that: 2x1, 2x2 and 3x1. Best printed in 0.3mm layer height…

Print approx. €0.78–€0.95 excl. taxPreliminary estimate for one variant

Downloads
271
Likes
70
Rating
5
P
PrintablesKollin

Utility Blade Filament Cutter 45° (1.75mm)

Printing No supports needed Print top pieces flat and bottom piece standing up as seen in STL files Materials 2 springs from ballpoint pens (preferably at least 22mm length, 4mm diameter) 1 utility blade ( Example ) Assembly Insert blade…

Print approx. €1.00–€1.22 excl. taxPreliminary estimate for one variant

Downloads
264
Likes
58
Rating
4.38
P
Printablesdennis0477

Felgenkappen, Radnabenemblem 50mm Alfa Romeo 145, 146, 147, 156, 166, Spider, GT, MiTo 60652886

Nabeldecken für viele Serienfelgen der Marke Alfa Romeo mit 50mm Durchmesser. Original Artikelnummer: 60652886 Die Embleme gibt es sehr günstig aus China wie z.B AliExpress oder andere Gedruckt in massiv PETG. PLA ging bei mir nicht, da…

Print approx. €3.67–€4.49 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
252
Likes
23
Rating
0
P
Printablessteffenbew

LED Light Strip 45° Mount

LED strip mount to clip a light strip in a 45° angle. I designed it for a Philips Hue Lightstrip to be mounted behind a cabinet. The mount can be taped to an object, but in my case I decided to drill holes afterwards and mounted it with a…

Print approx. €0.11–€0.14 excl. taxPreliminary estimate for one variant

Downloads
250
Likes
63
Rating
5
P
PrintablesMockab

RJ45 Dust Cap with Pull Tab

Dust cap for network jacks with easy pull tab

Print approx. €4.67–€5.71 excl. taxPreliminary estimate for one variant

Downloads
250
Likes
22
Rating
4
P
PrintablesEFY

Best Sink Filter Strainer 38mm - 45mm Compatible

Design Description: Sink Drain Filter This design is a specially crafted sink drain filter aimed at enhancing the cleanliness and functionality of sink drains. Compared to traditional sink drains, it is more efficient and user-friendly.…

Print approx. €0.85–€1.04 excl. taxPreliminary estimate for one variant

Downloads
249
Likes
30
Rating
5
P
Printables3DP-MAMSIH

Remix 45deg Fan Duct For Mk3s R6 version

Remix 45deg Fan Duct For Mk3s R6 version

Print approx. €0.48–€0.59 excl. taxPreliminary estimate for one variant

Downloads
243
Likes
24
Rating
5
P
PrintablesVincent

Dewalt DW745 Table Saw Overhead Dust Collection

Disassemble the blade guard and install this print using the stock hardware. I used a zip tie to secure it to the end where there is no hardware. Other solutions seemed like a lot of complexity where this “just works”. Fits 2.5" vacuum…

Print approx. €4.81–€5.88 excl. taxPreliminary estimate for one variant

Downloads
162
Likes
34
Rating
5
P
Printablesrvaccaro

Bag Rail Picatinny for CZ 457 LRP

I redesigned the original model in order to better fit to cz 457 lrp Please print with many walls and durable rolls

Print approx. €2.28–€2.79 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
153
Likes
9
Rating
0
P
PrintablesAdrienAG

Gun4IR GCON45 Solenoid model 0530 Support

This is a no cut mod support for a 0530B solenoid model to fit in a Namco GunCon 45 made to be compatible with Gun4IR official PCBs. The model is composed of two parts that are glued together on their flat surface for printing without…

Print approx. €0.37–€0.45 excl. taxPreliminary estimate for one variant

Downloads
143
Likes
17
Rating
0
P
PrintablesAndreas G

Keine Werbung Schild 20x45mm

“Bitte keine Werbung” Schild (sign) Gcode beinhaltet einen Farbwechsel (gcode contains a color change) 20x45mm

Print approx. €0.11–€0.13 excl. taxPreliminary estimate for one variant

Downloads
140
Likes
11
Rating
4.67
P
PrintablesThe Mapster

One Sided Small 45deg Double Switch - Brio/IKEA Wooden Train Track

Print as shown in screen shots with flat (non-track) side down to plate.

Print approx. €1.47–€1.80 excl. taxPreliminary estimate for one variant

Downloads
127
Likes
18
Rating
5
P
Printablestom

Adapter BenQ Screenbar Halo - Philips 345B curved monitor

Die wirklich gute BenQ Screenbar Halo passt nicht richtig auf meinen Philips Curved Monitor 345b. Die Monitorhalterung rutscht nach einiger Zeit in den Anzeigebereich, was ich als sehr störend empfinde. Der mitgelieferte Original-Adapter…

Print approx. €1.57–€1.92 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
120
Likes
7
Rating
5
P
PrintablesSilverBullet126

Hitron CODA-4582 Wall Mount

This is a wall mount for the Hitron CODA-4582 or 4680 (Rogers Gigabit) modem. The holes are M3 sized so M3 screws or #6 screw will work. Drywall screws fit as well. Print instructions Print using the included 3mf file or go simple and…

Print approx. €4.10–€5.01 excl. taxPreliminary estimate for one variant

Downloads
117
Likes
4
Rating
5
P
PrintablesGearheadaddy

45 degree Sunlu Drier ptfe connector

This is a piece that will help to dispense filament from the Sunlu Drier... Put a small piece of ptfe in the adapter...I

Print approx. €0.20–€0.24 excl. taxPreliminary estimate for one variant

Downloads
117
Likes
10
Rating
2
P
PrintablesInqEnzo

Vac 1 2"PVC elbow 45deg

In a dust collection system the max elbow you should use is a 45deg sweep. I have tried to keep my system to no more than 30deg. But now with the addition of the new wood lathe space became a problem so here is a 45deg sweep that I needed…

Print approx. €7.23–€8.84 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
112
Likes
7
Rating
0
P
PrintablesND

Metabo ASC 145 Battery Charger Wall Mount

No supports needed. Print with a high layer height for extra sturdiness. I've designed a hollow cone inside the pins for a higher break resistance.

Print approx. €0.48–€0.58 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
97
Likes
9
Rating
0
P
PrintablesJBoe

MEPLA 538.002.45.01 - Ersatz für Kunststoffschiene-Halterung

Object Description: Ersatz für Kunststoffschiene-Halterung 538.002.45.01 von MEPLA. Diese wurde in Häcker-Küchen und von anderen Küchenherstellern in Schubladen verbaut. Die Schienen sind nur noch selten gegen gutes Geld oder vielleicht…

Print approx. €0.39–€0.48 excl. taxPreliminary estimate for one variant

Downloads
92
Likes
1
Rating
0
P
PrintablesAinon3Dtisk

Imitation .45 Colt cartridge

Hello, Welcome to my profile, full of models and miniatures :-) I have for you Imitation of .45 Colt cartridges. For Colt 1911, Glock .45 cal. and others. The cartridge is suitable for exhibition, decoration, or perhaps as cosplay. The…

Print approx. €0.74–€0.91 excl. taxPreliminary estimate for one variant

Downloads
84
Likes
11
Rating
0
P
PrintablesmoWerk

W639 Electrical Fuse Box Latch Clip | A6395450073 VERRIEGELUNG | Mercedes Benz Vito Viano

Replacment for Electrical Box Clip A6395450073. In case one of yours broke or went missing. Print in PETG or ABS to ensure temperature resistance.

Print approx. €0.58–€0.70 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
83
Likes
11
Rating
0
P
PrintablesTinnT

Voron V0 mount for adxl345

This is rigid mount for an adxl345 over the 30x30 fan of Voron V0. The required hardware is: 2x M3x6 - for mounting the adxl345 to the mount. 2x Threaded Inserts M3x5x4. 2x M3x20 - for mounting over the fan.

Print approx. €0.24–€0.30 excl. taxPreliminary estimate for one variant

Downloads
82
Likes
12
Rating
5
P
PrintablesFilip

Device holder CFMOTO 450MT

Mobile holder CFMOTO 450MT

Print approx. €11.41–€13.94 excl. taxPreliminary estimate for one variant

Downloads
81
Likes
5
Rating
4
P
PrintablesJohn

45 Vinyl Record Adapter

No need for support No nonsense adapter.

Print approx. €0.45–€0.55 excl. taxPreliminary estimate for one variant

Downloads
80
Likes
5
Rating
0
P
PrintablesCarlos Mercado

Mercedes A45 AMG Silhouette

You can scale it and print it with normal settings i recommend .12 with 10% infill 50 mm/s speed with an ender 3 v2 neo

Print approx. €7.51–€9.18 excl. taxPreliminary estimate for one variant

Downloads
70
Likes
8
Rating
0
P
Printables969493CD10A4

Prusa 45deg fan nozzle/duct

Replacement because mine melted down. It happens occasionally. Printed in ABS, of course.

Print approx. €0.42–€0.52 excl. taxPreliminary estimate for one variant

Downloads
66
Likes
1
Rating
0
P
PrintablesRascalHoudi

GE 45170 Power Bar Mounts

Brackets to mount the GE 45170 powerbar in the shop or under a desk. Category: Organization

Print approx. €1.46–€1.78 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
61
Likes
5
Rating
0
P
PrintablesMat

HL15 45Drives - Unofficial Cantilever Fan Bracket

This will allow you to mount a 120 mm fan above your PCI slots for extra cooling. I use a 2mm bolt to attach the bracket to the case as that is about the size of the slots on the case. The bracket will accommodated a fastener that is up…

Print approx. €0.67–€0.82 excl. taxPreliminary estimate for one variant

Downloads
60
Likes
9
Rating
0
P
Printablesmstejska

Print approx. €0.46–€0.56 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
58
Likes
4
Rating
0
P
Printablesdodasch

Debowler Lid with GL45 thread

a Debowler Lid with GL45 thread for Arizer Stems for your avp You need additionally one flask with GL45 thread, just search for “GL45” in the www choose your debowler spatula, wether you have the round sieves or the flat ones use the .3mf…

Print approx. €2.02–€2.47 excl. taxPreliminary estimate for one variant

Downloads
57
Likes
10
Rating
4

Polar M450 running watch strap

If you want to run with Polar M450 print up this model join it with strap and you can go running. New X-Treme 20mm Tough Secure Hook and Loop Watch Band Strap Gents Men's with Ring End - Light Brown | Amazon.com

Print approx. €0.57–€0.69 excl. taxPreliminary estimate for one variant

Downloads
43
Likes
2
Rating
0
P
PrintablesJDPrints

45LC Better Ammo Box

This is a remodel from MortalWombat's Better Ammo Boxes! He's got really great designs for Ammo Boxes for Calibers he has on hand. Unfortunately, he didn't have a 45 Long Colt so I took his 45ACP ammo box and scaled it up to 125% for the…

Print approx. €8.75–€10.70 excl. taxPreliminary estimate for one variant

Downloads
37
Likes
7
Rating
0
P
PrintablesGeoff

Infill-Based 7-inch / 45 RPM Adapters

Some quick and easy 7-inch record centre adapters, all done in-slicer. A workable concept. These were made with the same principle used in an earlier project of mine for infill-divided battery holders - this time with the centred gap of…

Print approx. €0.09–€0.12 excl. taxPreliminary estimate for one variant

Downloads
37
Likes
6
Rating
0
P
PrintablesAlexa3D

Fraesschablone 45 x 45mm Abstand | Netzschalter / Netzfilter - Virtueller Pinball (VPin)

Fraesschablone Netzschalter / Netzfilter - Virtueller Pinball (VPin) Für meinen Virtuellen Flipper habe ich 2 polige Netzschalter bzw. Netzfilter eingebaut. Abmessungen 47mm x 28mm Abstand vom Rand bis Aussparung: ca. 45x45mm Ecke Platte…

Print approx. €1.79–€2.19 excl. taxPreliminary estimate for one variant

Downloads
33
Likes
7
Rating
0
P
PrintablesBasic

Rectangular Duct 110x55 - 45° Vertical

Meeting my local store I was shocked by how expensive those parts are (reg. EUROPLAST System 110x55) and made some parts myself. Model is for 0.8mm Nozz and NO Supports (whilst therefore, my design is a little different compared to the…

Print approx. €3.46–€4.23 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
31
Likes
5
Rating
0
P
Printablesmstejska

Ammo box 45-70 GOVT 405

Box for ammo 45-70 GOVT 405

Print approx. €7.34–€8.97 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
30
Likes
1
Rating
0
P
Printables3DPrintM.D.

Replacement Lid and Knob plus a Silencer Kit for circa 1990 Braun 4045 Coffee Grinder

The lid and timer knob on my circa 1990 Braun Coffee Grinder broke and, even though it is very loud, I did not want to part with it. So, I created these 3D printed repair parts that both served as replacements for the lid and knob and…

Print approx. €1.16–€1.42 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
29
Likes
1
Rating
0
P
Printableswerk.6011

Jung 245.07 spare part dimmer cover

The part can be used on a Jung 245.07 dimmer if the original bracket for the cover is broken. Other dimmers and covers will probably also fit. I printed it for better stability, as shown in the screenshot from the slicer. The adhesion was…

Print approx. €0.24–€0.29 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
29
Likes
0
Rating
0
P
PrintablesDustinW

LEGO 75457 wall mount

wall mount for the LEGO 75457 UCS Executor

Print approx. €2.14–€2.62 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
23
Likes
4
Rating
0
P
PrintablesDasMia

Dancing Clef 45 record adapter

This is the dancing clef record adapter. To make one you have to print 1 adapter and 8 clef attachments. Assembly is simple: just put all 8 cleft into the 8 half-moon shaped openings of the adapter. Make them dance: To achieve the dancing…

Print approx. €0.32–€0.39 excl. taxPreliminary estimate for one variant

Downloads
22
Likes
3
Rating
0
P
PrintablesKlemmworks

Wall Mount - RE45

Very Simple Wall Mount for RE45 Pistol from Apex Legends Uses a Command strip to fasten to wall. For model RE-45 AutoPistol Printing: Layers: ≤ 0.3 mm Supports: None Infill: 10% Also check out the pictured Han Solo DL-44 and accompanying…

Print approx. €0.36–€0.45 excl. taxPreliminary estimate for one variant

Downloads
19
Likes
7
Rating
0
P
PrintablesJan Bic

3030 120degrees (or 45) connection stiffer

I was quite surprised how few of this 120 degrees connectors is available to download, for 3030 it was none, so here one is :) I printed it from pla (as i think it is not that bendable as petg), 0,25 structural, 5 perimeters 5 top and…

Print approx. €0.64–€0.78 excl. taxPreliminary estimate for one variant

Downloads
18
Likes
2
Rating
0
P
PrintablesKevinWRay

Ghost In The Shell SAC 2045 Lithophane

Ghost In the Shell SAC 2045 Lithophane has two layers lithophane.

Print approx. €0.88–€1.07 excl. taxPreliminary estimate for one variant

Downloads
17
Likes
5
Rating
0
P
PrintablesKarel

Climp for RJ45 crimper model TV37

Crimper model: TV37 PLA or PETG, 0.2mm

Print approx. €0.16–€0.20 excl. taxPreliminary estimate for one variant

Downloads
17
Likes
5
Rating
0
P
PrintablesPapyjo

Lego pare brise vintage 4x3 45 degré

Il me manquait cet élément pour terminer ma vedette de police. Impression en PETG avec filament clear. Hélas la couleur et la transparence ne sont pas là, mais la fonctionnalité est respectée J'ajoute le fichier fusion si vous avez…

Print approx. €0.33–€0.40 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
17
Likes
3
Rating
0
P
PrintablesFalling Entropy

Wild Card Wheel - fast print...45 minutes total!

I also sell the physical print of this on Amazon.com here where you can find a couple videos showing how to use it! Elevate your card game experience with this innovative Wild Card Wheel! Measuring 4.5 inches in diameter and 0.25 inches…

Print approx. €0.13–€0.16 excl. taxPreliminary estimate for one variant

Downloads
15
Likes
7
Rating
0
P
Printablesandrea cabrini

dima per battiscopa taglio 45

serve per tagliare battiscopa alti fino a 10 cm

Print approx. €17.08–€20.87 excl. taxPreliminary estimate for one variant

Downloads
15
Likes
0
Rating
0
P
PrintablesAleš

PLASTOVÁ STOHOVATELNÁ KRABIČKA 185 x 145 x 55

PLASTOVÁ STOHOVATELNÁ KRABIČKA 185 x 145 x 55 po vytištění stačí odlomit podpěry na rozích a je hotovo ..

Print approx. €5.84–€7.14 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
15
Likes
2
Rating
0
P
PrintablesCaspar Armster

Prusa Mini Emclosure RJ45 Extension Holder

RJ45 Extension Holder for the Prusa Mini Enclosure, which can be screwed to the back of the enclosure. This makes the enclosure more transportfriendly because now you have an easy to reach connection for your LAN cable. All you need is a…

Print approx. €0.59–€0.72 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
14
Likes
5
Rating
0
P
PrintablesCyberdyne

Filament Storage / Dry Box (IKEA SAMLA 45l / 12 Gallon)

For the filament storage/dry box you will need an IKEA SAMLA (45l/12 Gallon) box, a wooden broomstick and 16 small woodscrews (2 nails are optional). If you just want to store and dry a few rolls of filament, you can just print 4 endcaps…

Print approx. €0.86–€1.06 excl. taxPreliminary estimate for one variant

Downloads
14
Likes
3
Rating
0
P
PrintablesAllpa

Basic Clock-Stand for Hama PP-245 / Uhrständer für Hama PP-245

Der eingebaute Ständer der Uhr, um sie auf ein Sideboard oder einen Schrank zu stellen hat leider einen viel zu flachen Winkel und lässt sich auch nicht einstellen. Daher habe ich diesen einfachen und schlichten Sockel entworfen, der die…

Print approx. €2.71–€3.32 excl. taxPreliminary estimate for one variant

Downloads
14
Likes
0
Rating
0
P
Printablesdfeissle

porthole456

Replacement part for a porthole cover. Three different version (4,5,6). Main difference is between the sizes on inner porthole that lines up with the bedliner. Six is the final version. Screenshot shows original factory part and 3d…

Print approx. €0.99–€1.21 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
9
Likes
0
Rating
0
P
PrintablesOgre Ray

4Runner Small Switch on center - Ethernet RJ45 cable Adapter

I remixed this to fit a GMRS extension RJ45 (CAT5) cable that's routed from the arm rest through the panel...I resized this to fit the smaller port in the bottom, and added two cutouts: pass through for CAT5 Cable for install larger hole…

Print approx. €0.29–€0.35 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
8
Likes
1
Rating
0
P
PrintablesOBA

Removable magnet wall holder for 45x32cm photo printed on metal sheet by displate.com

Motivation For Christmas I got a special present from my son: A 45x32cm photo printed on metal sheet by displate.com For mounting this poster, a 80x80mm magnet needs to be glued to the wall. The magnet then can hold the metal sheet paster…

Print approx. €0.98–€1.19 excl. taxPreliminary estimate for PETGSource material: PET

Downloads
7
Likes
0
Rating
0
P
PrintablesPrintyet

LED-Eckprofil 45° mit Klick-Diffusor, Endkappen und Verbinder

LED-Eckprofil 45° – mit einklickendem Diffusor Ich habe dieses Profil für LED-Streifen mit einer maximalen Breite von 15 mm in Fusion360 entworfen. Der Streifen wird auf die schräge Fläche im Kanal geklebt, das Licht tritt unter 45° zu…

Print approx. €0.07–€0.09 excl. taxPreliminary estimate for one variant

Downloads
6
Likes
4
Rating
0
P
PrintablesJavier Otero

Conector tubo 102mm marcho macho 45 grados

Conector para tubo flexible de 102mm en formato marcho macho a 45 grados. Yo lo voy a utilizar para el tubo de la salida de humos del extractor de la cocina.

Print approx. €9.22–€11.26 excl. taxPreliminary estimate for one variant

Downloads
1
Likes
0
Rating
0
P
PrintablesPomi

Filament Cutter 45°

Print No supports needed. Tested with PETG and PLA. Material One segment from snap-off blade 18 mm ( example 1, example 2) 2 pieces of screw M3 x 25 mm 2 pieces of ball pen spring (probably 20 mm length, 4 mm diameter, M3 screw must fit…

Downloads
22,191
Likes
12,904
Rating
4.87
P
Printablesguss67

Ethernet | RJ45 clip to secure/repair/fix broken tab

This clip was design to fix/repair/secure the broken or loose tab of a RJ45 Ethernet connector and avoid crimping. Designed to prevent from moving, wiggling, falling from the connector and easy to install. UPDATE 27/01/2021 Added the 3…

Downloads
21,963
Likes
7,496
Rating
4.84
P
PrintablesWilko_SLO

Elephant 3D Puzzle (45 pieces)

Elephant is 14 cm long, 10 cm high, and 6 cm wide. Designed to Print with PLA Z=0,2 Suggest to set Bottom layers to 10 Some of them need a brim. See the picture. (I placed them on the left side.) It should look like: Set selective brim…

Downloads
18,542
Likes
4,248
Rating
4.71
P
PrintablesTitafubaki

Business Card Holder 45°

You can find an updated version here: https://www.printables.com/de/model/963555-business-card-holder-45deg-v2-improved The Model should print good as is without support if your printer can print overhangs at 45°

Downloads
6,921
Likes
1,906
Rating
4.96
P
Printablesmfischer79

Ethernet (RJ45) Cover/Plug/Cap

Ethernet (RJ45) Port Dust Cover cap with grip for easy removal. Just added: New slimmer/narrow model for switches with closely spaced ports. Check out all other port covers: USB-A port cover -…

Downloads
4,617
Likes
406
Rating
4.8
P
PrintablesGeorge

Ender 3 (V2&PRO) ADXL345 Bed Mount

I made a remix of this . I add the bottom protection in order prevent the screw to damage the PCB on the back of the bed and made some wall thicker to reduce the flex. Print the 2 parts and assembly using an M3 nut and max 10mm screw to…

Downloads
3,555
Likes
447
Rating
4.95
P
PrintablesPosterBored

Gravity Knife no-screw Remix - 45mm

I printed this for my son, beautiful print, but wanted one for myself. I made it 15mm longer so it fit my hand better. Make sure to paint the seam on the blade down at the bottom where you won't see it. 👍

Downloads
3,361
Likes
570
Rating
4.79
P
PrintablesJohn K

RJ45 Ethernet Cable Clip Repair

These are replacement clips to fix broken ethernet cable clips. The clips attach to the Ethernet cable and replace the broken clip so that the cable stays locked into an Ethernet port. EDIT - For some reason Simplify3d doesn't like this…

Downloads
3,234
Likes
1,110
Rating
4.79
P
PrintablesMrHanjak

Tractor - Zetor Crystal 8145 (NO SUPPORTS)

🟦 Zetor Crystal 8145 🟦 !!!Warning!!! Not suitable for small children. The model contains many small parts, risk of inhalation and suffocation. TIRE UPDATE - If you choose to print this update, don't print these parts black 15 by MrHanjak…

Downloads
3,225
Likes
989
Rating
4.97
P
PrintablesLinkDesigns

Hexagon Superfidget V2 - 45 Segment PIP Design

Introducing the Hexagon Superfidget V2: Upgraded to 45 segments with improved expanding and twisting action, and 3 sizes available! Print Tips: Especially for the full size fidget, watch your first layer carefully. I recommend slowing the…

Downloads
3,166
Likes
296
Rating
4.93
P
PrintablesClaus

Filament Cutter 45°

New edition - April 2025: A guide pin has been added to prevent the cutter from twisting. The thread for the screw has been made more print-friendly. All that is needed in addition to the printed parts is 1 segment from 18 mm snap-off…

Downloads
3,154
Likes
273
Rating
4.96
P
PrintablesVlad Grigore

3D Multi Angle Measuring Ruler 45/90 Degree, Carpentry Square Protractor Drawing Line Ruler Miter Triangle Layout Tool

Sometimes all you need is a 45/90 degree tool for tracing and cutting. It is a 2 piece tool that is a must-have in any Carpenter toolbox. You can use them combined and it is good to join wood planks at 90 degrees or to trace lines tracing…

Downloads
3,005
Likes
876
Rating
4.78
P
PrintablesGunter

RJ45 Ethernet Cable Connector Repair

This design is a unique combination of the short designs, where the latch is fixed at the connector and the longer designs, where the clip is mounted to the cable behind the collet. The design considers the exact dimensions of the collet…

Downloads
2,946
Likes
1,272
Rating
5
P
PrintablesBlackFury

Drill Guide - Metric - 90/45 degrees and corner

This is a remix of Helasius drillguide - https://www.thingiverse.com/thing:4839621 However, I needed it to be able to drill on a square corner. As per the original description, it fits sizes 3, 4, 5, 6, 8, and 10, with holes at 90º and…

Downloads
2,896
Likes
446
Rating
4.96
P
PrintablesCanislupus

Never lost Ikea Samla Clip (45l + 65l) V2

Summary Are you tired of searching your clips for your airtight Samla box once opened? You like the simplicity of print-in-place parts? Then this Samla clip is for you. The only thing you need are some drops of glue to fix the clips.…

Downloads
2,822
Likes
462
Rating
4.92
P
Printablesschreider

Filament Cutter 45° for Flashforge Adventurer 5M (AD5M) Printhead

The rest of the files can be found → HERE ←, as well as a description of the necessary parts. The model is put directly on the filament slot on the printhead. Therefore, to change the filament, you will no longer need to remove the tube…

Downloads
2,753
Likes
483
Rating
5
P
Printablesmt_benno

T45 power armor from Fallout 4

Ripped straight from the Fallout 4 game files. 55k triangles 154k vertices

Downloads
2,382
Likes
176
Rating
4.25
P
PrintablesStranula

Multiboard Corners 45° & 90°, 6.25, 8, 12.5 & 15mm

I have an insider corner above my workbench where I am putting up a multiboard. I couldn't make any of the premade brackets work for my needs, so I made my own. These are working for me and can be seen in the attached images Updated…

Downloads
2,288
Likes
329
Rating
4.9
P
PrintablesUlle

LED Strip profile 45 Degree

I have designed this profile for LED strips up to max 15mm wide. The beam angle is 45 degrees, making this profile perfect for indirect lighting. The fit is perfect and the diffuser snaps into place on the side without the need to use…

Downloads
2,279
Likes
768
Rating
5
P
PrintablesCarletes359

Ethernet RJ45 repair fix with NO SUPPORTS

Ethernet cable fix which prints WITHOUT SUPPORTS. The layer line orientation aids in keeping the cable in the port. Print settings: layer height 0.2mm 3 thick walls Infill: Does not matter since the piece is too small to even have infill…

Downloads
2,149
Likes
414
Rating
4.53
P
PrintablesEmethian

RE-45 AutoPistol (Titanfall/Apex Legends)

The RE-45 is a staple of the Frontier war, initial appearing in the hands of IMC soldiers as a effective suppressent for local dissent and providing cover fire for advances. Eventually it made it into the hands of Militia forces and again…

Downloads
2,095
Likes
594
Rating
4.25
P
PrintablesIPIND 3D

Prusa MK3S Improved 45 Degree Fan Shroud

Based on the original Thing from K_Lab - thanks for the source Fusion 360 files: https://www.thingiverse.com/thing:3533859 and the remix from Theo Tinjum:…

Downloads
2,074
Likes
364
Rating
4.89
P
PrintablesCanislupus

Ikea Samla 45l Filament Buffering Dry Box V2

Summary Smart Dry Box designed for the Ikea Samla 45l box. It supports 6 spools, each buffered by a fully enclosed wheel buffer utilizing the complete box height. Spools, Buffers and Desiccant containers all can easily be loaded from the…

Downloads
2,005
Likes
802
Rating
4.86
P
PrintablesButlers3D

RJ45 Dust Cover

Designed to protect the RJ45 sockets of my small Ubiquiti Unifi Flex Mini Switch that sits upright on my desk. Can be used on any other RJ45 sockets… Recomended Material : PLA Nozzle Diameter : 0.4mm Layer Height : 0.2mm Support : YES…

Downloads
2,002
Likes
165
Rating
4.95
P
PrintablesSTORM DESIGN

Bambu Lab Filament Cutter 45°

This is a Remix “Bambu Lab Filament Cutter 45” for an project "Filament Cutter 45" Design by @Pomi ATTENTION - WEAR GLOVES TO PROTECT AGAINST CUTS WHEN INSTALLING THE BLADE. USE PLIERS TO ASSEMBLE THE BLADE !!! Hello Everyone I didn't…

Downloads
1,929
Likes
244
Rating
5
P
PrintablesLoneWolf052

45°Shade Foregrip

UPDATE 19th Apr 2023: Body and Bracket have been replaced by reinforced versions. .stp has been updated too. Rest stays the same. This is the 45°Shade Foregrip an alteration of my vertical foregrip design. It has all the features of the…

Downloads
1,868
Likes
342
Rating
5
P
Printablesmodsmthng

blind shaker : donut 58mm 57mm 54mm 51mm 49mm Flair Pro 2 (45.5mm) Flair Classic (Donut espresso shaker / donut espresso shakr)

The Donut Espresso Shaker is an espresso shaker that enables even distribution when preparing espresso for a wide range of portafilter sizes. What makes the Donut Shaker special is that it achieves this result with any portafilter size…

Downloads
1,824
Likes
208
Rating
4.91
P
Printableskmccon

PRUSA MK3 AIR INLET 45°

I really liked the latest changes to the Prusa i3 MK3 Extruder. However, I don't really like pulling the part cooling air from the heated bed. 1. Maybe a little warmer ?. Cooling off the bed faster? The 45° fan configuration makes that…

Downloads
1,754
Likes
332
Rating
4.87
P
Printablesoriddlero

Tool Trays - Prusa MK3S Right & Left Side w/ Honeycomb, PRUSA logo & 45 Degree Matched OEM Front

The original design was a nice start / frame, however, I thought it would be an improvement (and a big savings on filament / print time) to add honeycomb cutouts, a 45° front angle (to match the OEM front panel angle), & added the PRUSA…

Downloads
1,682
Likes
402
Rating
4.93