Water pipe connector Joiner and Devider
Print it and add O-Rings 15,8x3,1 Print Orientation with support for enforces only.
- Downloads
- 2,524
- Likes
- 359
- Rating
- 4.5
383 models
Print it and add O-Rings 15,8x3,1 Print Orientation with support for enforces only.
Hi, I remade this model put with a print-in place hinge. I added my fusion 360 file which is parametric - meaning if the print in place is too tight, you can make it “lose” in the model. Look at the image referring to that (file: Filament…
Hi, This is my filament splicer/joiner that I designed for the purpose of consuming entire rolls of filament and also enabling multi-color prints. I also made a spool holder to clamp to my desk. Splicer will fit desks up to 30mm and the…
By request, two hex inserts, joined as right angles so you can use it to join two panels together. If you want a larger (or indeed smaller) gap in the corner, use the OpenSCAD file and change the variable extra_separation.
I was looking at the Honeycomb Storage Wall and it looked pretty neat. And so I set in motion the plan to print some honeycomb bits to fit on my wall. So I started out paramaterizing the honeycomb to fit. And I saw someone made pretty…
A handle for a Ruger 10/22 magazine, and magazine joiners. The 10-round magazines are fiddly things to manipulate, and recess into the rifle receiver. This handle gives you something to grab onto to extract stuck magazines, and to rapidly…
This model is compatible with the lego system.
Shelfie allows you to design your own storage and shelf systems using a fully parametric design. Simply generate the required Shelfie connectors based on your preferred storage layout using OpenSCAD. It is based on the original concept…
As the name. You need 5 JP4-01 or PC4-M10 to use this. The JP4-01 has shallow cut so it's preferred to minimize the filaments getting stuck.
0.75in. 19mm. Pipe Joiner PETG recommended for outside use. Increasing wall count or infill to 100% for better strength. No supports
A pipe joiner that joins 0.75in.(19mm.), pipe to 0.5mm.(12.5mm.) pipe. PETG recommended for outside use. Increasing wall count or infill to 100% for better strength. No supports
0.5in. 12.5mm. Pipe Joiner PETG recommended for outside use. Increasing wall count or infill to 100% for better strength. No supports
These are 90 degree turn with a 10 degree bank hot wheel tracks with joiners. Its input / output are level so there is no drop in this design. The tongues are designed to be push together / pull apart, which is showing to be easier than…
Soldering wire joiner holder Suits 10 - 30 AWG gauge wire If you find this part useful please would like to support me, you can buy me a coffee :) https://www.paypal.com/paypalme/ikom Let me know if you have any suggestions to improve my…
I designed these fasteners to help me connect my spare cardboard boxes and pieces together to make structures for both my kids and our bunnies! Each bracket features non-destructive teeth that help to grid the cardboard for extra grip.…
A handle for a Ruger 10/22 magazine, and magazine joiners. The 10-round magazines are fiddly things to manipulate, and recess into the rifle receiver. This handle gives you something to grab onto to extract stuck magazines, and to rapidly…
This 3D printable piece features identical geometry on both sides and is designed to be printed twice using model 'A.' Whether used as a standalone piece or incorporated into your projects, it delivers exceptionally satisfying and…
Simplest Ever Filament Joiner Ever (Ever) NEW AND IMPROVED Update 04-11-2022: No screws and now no cable-ties required. Many thanks to jcjames_13009 for suggesting his ‘hollow squares’. These are now part of the print with grips on the…
This 180 degree turn with a 45 degree bank hot wheel track with joiner has the ability to be mounted via a m5 x 6.7mm heat set brass insert from McMaster. Its input / output are level so there is no drop in this design. Step files are…
MELD: A Filament Joiner September, 2022 After working with Mosaic’s Palette 2 Pro, I wanted to find a cheaper off the shelf method for filament joining that didn’t cost $500. Sticking to Recreator3D’s mission; I started work on, MELD: A…
Sunlu FC-01 Filament connector/Joiner tool. PETG
Easily add splines to your mitered joints such as picture frames with this jig. This project was inspired by a video by David Picciuto and I wanted to help improve upon his "least favorite method" for adding splines (…
As the name. Made for BAFS v.01, but can be used for other similar use. You need 5 PC4-M10 to use this. Inspired by other splitters: https://www.thingiverse.com/thing:2444687 https://www.thingiverse.com/thing:2867089…
Pipe fitting adapter/joiner for the drain hoses of a washing machine and condenser-dryer. As printed it fits my Bosch washer and Haier dryer perfectly. The model is parametric, so should be adjustable for other sizes. As uploaded, fits a…
These joiners let one IKEA LACK table sit on top of another securely. The cross-shaped peg makes a solid connection and ensures that the table legs won't rotate. The tables are not fastened together; you can lift the top one off at any…
This bracket relocates the filament sensor on the Anycubic Kobra S1 combo, designed specifically to address friction and positioning limitations I encountered with other solutions. Key features include: Repositions the sensor straight…
I put four of IKEA's “Billy” bookshelves in a room and found them to stand slightly unevenly, probably due to the uneven floor. Like every problem I encounter nowadays, there was a way to 3D print a solution! This little bracket did the…
When in need of a Kato Unitrack Insulated Unijoiner , this 3D-printable solution is ready to click into place. Designed as an alternative to Kato’s 24-816 or 24-819 insulated rail joiners , it provides reliable electrical isolation for N…
Wanting to print at higher temperatures on my 3D printers, I had a need for this and didn't see anything readily available. Fusion 360 to the rescue!!! Due to the global supply chain making everything ridiculously expensive, I designed…
This jig is inspired by Makers_Fun_Duck's method for joining strips of PET bottle before they are put through the filament extrusion process (detailed in this video: https://www.youtube.com/watch?v=xNtrQQ42WG4&t=0s) The holes at the top…
This model is meant to be printed on it's side with build plate supports at a 0.1 or similar layer height. After printing use a small drill bit to clean the inside hole and also sand the outside surfaces to make the hose fit better. I…
This is a very simple joining piece for joining two hoses fitted with my CAMLOCK SHOPVAC CONNECTOR. Print it to match your connectors - or not! NOTE - I have not test printed this fitting, however as it is generated from my standard…
I needed some track insulators for my LGB style G-Scale layout. However, some were to be temporary, so I didn't want to modify the track segments. I created a custom Male-Female insulator (as well as a standard Female-Female). These are…
My two Billy bookcases, annoyingly, would not stay together so I made a simple bracket to hold them to each other. The brackets stay in place through friction and the fit can be made tighter by adding folded paper behind the bracket. You…
So i broke my blind chain connector, or maybe it was my kids, likely them. Anyways, it snaps together, easy to print, and if it pops apart, glue it shut with crazy glue. Screw spending $25 on amazon for 5…. like jeese.
A model of an insulated rail joint for H0 scale. It wasn't modelled for a specific rail code, but I tested it on Lima and Fleischmann rails. I printed it in PETG with a 0.4mm nozzle at a layer height of 0.2mm, lying flat on the build…
This is a ptfe y-joiner 2 in 1 for Pc4 M10 fittings. I print it as you can see in the pictures to avoid that the filament get stuck at the layers. I also avoid support inside the part. Feel free to remix with attached .stp -file.…
This two piece item joins the two ends of a cord - simply tuck the two ends of the cord into the inner piece and click it into place within the outer hood - now you have a handy thumb tab - great for zips on outdoor gear where you need…
A simple joiner that allows you to connect two ends of a length of 6mm wide GT2 timing belt. The joiner is shaped so it does not interfere with the teeth of the belt. Print with largest surface down. Slip the ends of the timing belt into…
This is a simple bracket to join together IKEA Lack tables. It is printable with no supports and 0.3mm layer height with 20% infill is fine. Included 2 x countersunk holes to enable screwing to the legs of the upper table in the stack…
Printed in two halves, because of the large size. No support needed. Connected by 2.5x8mm cylindrical pins and/or glue. There is a small gap when the box is closed. To make sure no parts escape from the organizer when the box gets tilted,…
Unprofessionally “Fused” the Joiner and Anchor, added some internal fill to make it more solid because it kept breaking. I personally printed it at 75% because I did not want it to break again. You can try it out with whatever infill you…
These are 45 degree turn with a 5 degree bank hot wheel tracks with joiners. Its input / output are level so there is no drop in this design. The tongues are designed to be push together / pull apart, which is showing to be easier than…
I designed this to stack my Prusa Lack Enclosure v2 ( https://blog.prusaprinters.org/mmu2s-printer-enclosure/ ) on a third Lack table. It uses these screws ( https://www.amazon.com/gp/product/B07M5SRLTF ) I originally purchased them for…
Update 03.07.25: Removed a little Design error. Thanks to @NickBerczyns_2829932 A small modification of the great model from D3D-Concept. I kept having problems removing the newly welded, still hot and soft filaments cleanly from the…
This is an adapter to connect the Magnetic PTFE Joiners by Line Arc Line to an EIBOS 3D Series X: Easdry filament dryer. It supports the “No Offset” type of PTFE joiner. It uses screws instead of additional magnets for the magnetic…
Bow or butterfly joinery model. aka bow tie, dovetail key, Dutchman joint, or Nakashima joint, is a type of joint or inlay used to hold two or more pieces together. Depending on the size, you may have to scale the bow up or down. I've…
Mysterious Japan Joinery, it's hundreds of years old, yet it is sole example of that specific joinery. It was found at Osaka Castle, which is over 400 years old. However, it was unique and how it was cut and assembled was a total mystery…
I ran out of fan screws and noticed that the PLA+ filament that I used far strong enough that screws aren't needed. I made a project using 8 fans. after quickly running out of screws I made these screwless connectors. They are a very…
Join your last lines of filament together, don’t waste them. This tool allows you to use a soldering iron or fine pointed heat gun or even a lighter to fuse lefter over filaments together. Simply use some ptfe or silicone tube to make a…
This 180 degree turn with a 30 degree bank hot wheel track with joiner has the ability to be mounted via a m5 x 6.7mm heat set brass insert from McMaster. Its input / output are level so there is no drop in this design. Step and Fusion…
Compare to Closet Maid Joiner Plates. I could no longer obtain the original designed plates from Closet Maid so I created a similar plate that is stronger with the original dimension for exact replacement. Please Like and Post your Makes.…
Remix of Lopata's model to accomodate 4mm PTFE and stiffer more rugged 8mm Spring Also added some tether holes
This is something I put together to let the community make. It's an all machinable aluminum XY Joiner. The design is free for anyone to make and distribute if they so desire. I have only printed this to test its fitment.
As the name. You need 5 JP4-01 / PC4-M10 to use this.
Great original mode, but for everyone not living in America, we cant access imperial screws. This was designed to use a 3D printed thread section, which can be glued or left as is so the screw can be assembled and disassembled. The…
PLEASE NOTE: My railroad uses battery operated locomotives so I have no need for electrical connection from rail to rail. If you have one of the more typical rail powered systems this model will not work for you without installing jumper…
This model is compatible with the lego system.
This is a flat snap-fit connector for 2040 V-slot aluminum extrusion profiles , designed to join two profiles side by side (or four 2020 profiles in a 2×2 layout) in a single plane. It connects the extrusions securely without screws or…
I have created RatRig v-core 3.1 extrusionless x-gantry - XY joiner inserts inproved - for more stable connection. Tested, works well. Also You can find spacers. Not tested…I have used some calibrated 10mm spacers with threds from Ali.…
As I liked the Clamping mod of the gold series (2 M5x20 bolts to hold the 2020 extrusion to the part AND metal botom plate) and I also liked Adam's (V3D) mod to remove the aluminium spacers and just mount the idlers, I combined both.…
Ikea Lack Tischverbinder, zum verbinden zweier Ikea Lack Tische. Ikea lack table connector, for connecting two Ikea lack tables. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: Doesn't Matter Supports: Yes…
Filament Joiner For filament with a diameter of 1.75mm. It also works wih homemade pultrusion filament. Build Instructions What you need 6x M3 Heat Inserts 4x M3x14 Screws (longer screws will work as well) 2x M3x6 Screws (Also here,…
Accessory for my Modular Racking System There is a short and a long set. They join the beams at a 45 degree angle. I chose 45 over 90 due to the length of the outside beam with a straight 90 (It does unfortunately mean needing an extra…
Similar to previous model, but with curves instead. Tested with BAFS v.01 and cheap no brand (white, green and bright orange) PLA and Sunlu PLA+ which has been exposed to open air for about 1 month (pink and black). See the pictures on…
This model is compatible with the lego system.
This 180 degree turn with a 45 degree bank and 40mm drop hot wheel track with joiners has the ability to be mounted via a m5 x 6.7mm heat set brass insert from McMaster. Step files are included if you want to modify the design. (Update:…
A cut for printing parts larger then the bed. Inspired from a pictured from @Matt Dongworth on FB. Print instructions this is a draft print for a larger than the bed assembly joint (to be published later) Printed on MK2.5S PLA 0.2 layer…
Used to connect cabinetry panels together. I have also included my FreeCAD file to make it easier to modify.
The default plinth joiner piece for the IKEA METOD system was tiny and easily knocked off while vacuuming and eventually lost and does not cover gaps. Designed a new piece using the joiner nubs for the original plinth end cap pieces and…
Remixed "NoOffset (Default)" for Luter PC4-M6 coupler
I wanted to repurpose some Misumi 2040 I had laying around from an old AM8 printer and decided I wanted to try to use it for the table of my upright Dewalt portaband saw. I tried multiple configurations ranging from using all double…
8x3 Magnets pushed in from the back
Joiner brackets and feet for the Hub 75 RGB LED Matrix Panel 128x64 2.5mm pitch. Model ships with the Pimoroni Interstate 75 Starter Kit https://shop.pimoroni.com/products/interstate-75-w?variant=55006518411643
Joiners for the Magnetic Shields for the LaserPecker laser units as sold by LaserPecker. The joiners allow to stack the shields one above the other and can be placed around the LaserPecker units to provide extra height protection. The…
Hi! I designed this simple 2020 V-Slot Profile Vertical Joiner. To bolt down two profiles, I used 5.8 5x25mm bolts, but that should be adjusted for your application :) It can be printed in PLA, but PET-G or ABS/ASA is recommended. Happy…
BOM: Printed with ROSA3D High Speed PLA Signal Violet This is a compact side connector for T-slot aluminum profiles , designed to join two or more extrusions directly side-by-side by sliding into their adjacent rail slots . The connector…
I designed this to raise the airport fan from being so close to desk and the scratching of the bottom of the Airport. A 2nd Airport also fits underneath if wanted to stack two or more. Put a rubber band around bottom of Airport to make…
This model allows for two drumsticks to be clamped together in transit and storage. Let me know if you would like me to post additional sizes with the same formula. This was printed in Prusament PLA with 5 percent infill on my MK3s+ at…
I needed to mount 6 - 120mm fans side by side on the front of the mining rig I built. I could not find any brackets that would hold the fans and then allow me to screw them to the face of the rig. I made these flush mount brackets. 1 set…
This is for joining Banana plug test leads. Here is the Banana plug to Pin Tip plug version... https://www.prusaprinters.org/prints/53545-banana-to-pin-plug-joiner Print instructions I used ABS but PLA should be fine.
Used to connect a VGA cable to a VGA extension cable. Provides a place to screw in the connectors so that they don't sep
These are the XY Joiners made by Vector3D https://github.com/AdamV3D/V-Core-3-Vector3DEdition/tree/main/Printer combined with the clamping mod of MFBS. https://www.thingiverse.com/thing:4947482 I changed the hole size back to 5mm and…
This is for the 10mm to 8 mm XY Joiner. I have included step files for the parts if you require to create a 8mm to 8mm derivative. My stock XY Joiners on my Hypercube Evo build started to split under the tension of the drive belts and the…
Piece for joining two sections of matchbox car track together. A friend from work had me design and make a couple of these for his kids' race track set. He claims they are working better than the original connectors and is using them in…
I have slightly reworked the endstop as the metal xy-joiners caused the endstop to no longer hit the switch. I have rotated the “block”, removed the notches underneath. I also made the “slider” part so not to slide but mount (standard…
Building a box frame out of 20mm PVC conduit, needed a joiner.
This is for those running the V-Core 3.1 beta 1 or 2 toolhead and the funssor CNC super lightweight XY joiners (see photo for the exact model - this is the lightest weight one they make). Running the stock end stops will result in your…
This simple bracket enables you to stack two Ikea Knarrevik tables together and utilises the existing holes in the legs. You can print without supports at 0.3mm layer height and 30% infill. You will need longer screws, and to remove the…
Handle for the Makita PJ7000 plate joiner which makes it more comfortable to use for me. The handle is mounted with a M6x15 countersunk screw and a M6 locknut. For mounting a hole with countersunk is needed, for the position see photo.…
Model is created for 10mm mill and 17mm copy ring Print instructions: PLA 0.3 layer height 0.6 nozzle Bottom thicknes 3mm 5 perimeters Top surface none Infill Honeycomb
Magnetic PTFE Joiner cap 6x3mm magnets I wanted a lower profile version compared to the ones that are out there, working with 6x3mm magnets and a space for the filament to stick out.
I just mixed 2 designs to have a all printable laptop stand that have a "joiner" to keep both sides at a set up distance. https://www.thingiverse.com/thing:3708825 https://www.thingiverse.com/thing:3011363 I'd like to thank bartnijs and…
3D printed part to attach the Rat Rig V-Core 4 IDEX Oozeguards to the MandalaRoseWorks Machined XY Joiners. Uses M3 Slim Nut OR M3 Heat Set Insert to hold the Oozeguards in place. NOTE: The Slim Nut version requires high printer tolerances!
Endstops blocks for: https://www.printables.com/model/548494-xy-joiner-ratrig-31-all-metal#preview and https://www.aliexpress.com/item/1005006198538785.html?spm=a2g0o.order_list.order_list_main.34.4e501c24fvgqof&gatewayAdapt=glo2pol X is…