97 models
If you intend to sell prints of this model, then please purchase a Commercial Use license version here . Main Features: - Improves thermals - Reduces fan turbulence by using circular cutouts for the fans - Easier fan mounting or swapping…
What's this? As seen in my FormD T1 v2.1 video , this anti-sag bracket secures the 4080 or 4090 Founders Edition stock air cooler and eliminates sag. Configurations supported: 3 slot 3.25 slot 3.25/3 slot (top strut in 3.25 slot + 5mm…
I designed this model to squeeze a bit more performance out of the Thermalright AXP90-x47 CPU cooler in the FormD T1 v2 case. The duct prevents re-circulation and ingestion of hot air into the cooler and can provide some passive cooling…
These are covers designed to plug the holes at the back of the FormD T1 case. I've prepared two different designs. Print Settings: Material: PETG Layer height: 0.20mm Supports: no Perimeters: 2
The newest V2.1 version of the FormD T1 case switched from threaded M19 holes to smooth. I found the existing plug model did not have an interference fit with the smooth M19 holes and made my own model of the plugs.
As seen in my YouTube video: The Ultimate FormD T1 Air Cooled Build Panels require a large print bed (300mm+) and a well calibrated printer. They are somewhat experimental, trial and error may be necessary to get satisfactory results. The…
This is a set of different supports and braces that can be used to prevent sagging of RTX 4080 & 4090 Founders Edition GPU's in the FormD T1 v2 (and v2.1). The two braces (short & long) attach to the case spine and provide support for the…
This model is based on my 4080/4090 FE original anti-sag bracket, but updated to work with the ASUS ProArt 40 series GPUs in the FormD T1 2.1 For a more robust solution, check out the official travel kit BOM: 3 x M3x5 countersunk bolts* 1…
Fan duct to redirect the hot air from inside the case to the outside and prevent a hot pocket between the fans and the top of the case. Based on the FormD T1 1.1 - 120mm Noctua NF-F12 PWM Fan Duct but completly rebuild and adjusted for…
New bracket for v2.0/v2.1 What's this? This is a PCI Rail attachment that I made for the FormD T1 v1.1 case, to be used with the RTX 4090 (and 4080) Founders Edition graphics cards only. It uses the existing SSD mounting holes of the T1…
This was not my idea. Dimensions: 165mm long, 155mm between center of holes, 10mm wide, 5mm thick, 3.4mm holes(⌀). You could make it one or two mm thinner but I think that would work better with a stronger material like CNCed alluminum. I…
Original SMX Heinz design of the 3D printed slot 3.00 & 3.25 flipped travel kit. Designed to use with ABS filament. If you print with other filament you may have to adjust shrinkage compensation to get the correct dimensions. Installation…
It adds 15mm to the top or the bottom side of the FormD T1 V2.x You may need to split the model into 2 parts to print it on a home printer. 2 M3 screws and 2 M3 nut are needed.
Liteweight remixed version with zero gap between radiator and fan body, 25mm fans support in 3 slot mode, precise strong mount, support Corsair Venegance memory sticks and similar height even with shift brackets for AM5
Remixed the O11 fan duct to fit in the FormD T1 together with my beloved Noctua NF-F12 PWM fans. It's a snug fit so that all of the air pressure is working to get the hot air out of the case instead of just circulating between the case…
Basic Under Desk Mount for the FormD T1 As inspired by Optimum Tech Sized for #10 Screws Print in PETG/ABS with lots of walls for strength. Print lying down on side like in second picture for maximum strength. Supports are going to be…
This is a custom parts collection for the ITX PC case FormD T1, including handles, feet, and rear panel spacers. To assemble you need: each Handle 3x M3x8mm screws, 3x M3 hex nuts each Feet 2x M3x8mm screws, 2x M3 hex nuts GPU spacer 2x…
Vertical stand for the FormD T1 V2 case. No additional post-processing or hardware required. Designed to work with the stock thumbscrews used to attach the top and bottom case panels. The OEM vertical stand provides a vertical clearance…
One piece anti sag bracket for the Asus 50 series Prime cards, Tested with the 5080 prime, but should work with the 5070 and 5070 ti prime cards as they all have the same dimensions. Just needs 3 x M3 countersunk screws, two to secure the…
The Best position for GPU cooling, 5080 FE is all all-throughflow design, so most space behind the card is desirable. The front and rear brackets makes a solid connection to the case. You need to install the bracket on the GPU first, then…
The standard set of fan brackets can replace the stock fan bars that come with the FormD T1 v2. They offer plenty of flexibility with fan positioning and lower the fans by about 1.5mm compared to stock. The quiet set of fan brackets…
This adapter allows you to bring your own USB C cable to use in the FormD T1 v2. I made this because I couldn't get my hands on one of the official cables when the case originally released and my motherboard doesn't support the current…
You can use these models to install up to 4 SSD's in the Formd T1 V2. To install 3 SSD's use the 3x SSD Bracket and mount it to the side of the first ssd behind the front panel with m3x5mm screws. If you want to install a 4th ssd (or just…
Low effort remix of @eiga's great GPU bracket. Use @eiga's original ProArt GPU mount. In use with a ASUS Prime 5080.
This is a handle and foot mod for the ITX PC case FormD T1. It is visually simpler and easier to assemble compared to the 2024 design. Required other than printed parts: 16x M3x8 Screws 16x M3 Nuts Required printed parts: 8x…
What is this? GPU Anti sag bracket to secure RTX 5080/5090 Founder Edition cooler from the rear side to eliminate sag. What have I modified from EIGA's original model ? Adjusted the model to fit RTX 5080/5090 FE. Made the structure more…
These are feet for the FormD T1. I designed them because I didn't like the included feet. To assemble you need: 4x M3x6 screws 4x M3 hex nuts Print Settings: Material: Prusament PETG Matte Black Layer height: 0.20mm Supports: no…
Underside Desk Brackets for the FormD T1 featuring 10mm - 30mm clearances with or without screw holes to secure your precious FormD T1 into place. Highly recommend printing in PETG/ABS at an infill of 40% or higher for maximum strength to…
UPDATED 1/12/2026 - Included bracket for the MSI B850 Edge TI board (uses coarse fan screws) UPDATED 1/11/2026 - STL file updated to 5.5mm offset instead of 3mm downward - Fusion file updated to have parametric adjustment for vertical and…
The stock FormD T1 v2 GPU IO cover blocks part of the rear exhaust opening on the Nvidia RTX 4080 / 4090 cards. I designed this shorter cover to fill that gap and not impede the exhaust airflow. This cover is compatible with both 3 and…
A labeled organiser for screws required to construct a FormD T1 case. The FormD T1 case is an incredible case, but unfortunately screws all come unsorted in one bag. So organising your screws before the build is highly recommended to make…
Requires 10x M3x4x5 heat set inserts and 8x M3 screws to mount your fans. Fan cable hole is sized for a 15mm diameter grommet with a 2mm wide groove (not pictured). No single-piece version included since I wanted the cable grommet in the…
connects the t30 to the top of the case to improve thermals
Summary Air Kit reduces temps, fan turbulence, and GPU fan speed in the FormD T1. It contains two parts that can be used together or individually: Fan Slab and Air Block. Fan Slab Fan Slab holds two 120mm fans and two 60mm fans. It prints…
I believe it’s very important not to block the gap between the motherboard and GPU, since it’s the main source of fresh air for one of the 5090’s fans. I intentionally made it as air-unrestricted as possible. Maybe (unlikely) I will make…
These brackets help better support the PSU in the FormD T1 SW across a few configurations. There are definitely more combinations of T1 slots and PSU stand-off lengths not included here, so the NX *.prt files are provided if you want to…
Printed in PETG As I have my radiator configured to be at the top of the case, the brackets seem adequate to hold it in place. Unsure how flipped config would support.
Compatible with the Formd T1 V2.0/2.1 Configurations possible : 3 slot 3.25 slot I personally recommand you 3.25 slot to avoid turbulence noise. BOM : 1x M3x8 Countersunk screw 4x M3x5 Countersunk screw You need to install first the…
Print it, glue it, sand it, stand it. Add some M3 set screws + 5mm M3 square nuts to secure rear IO. These are the parts that I used to get the rear IO forwarded: https://www.amazon.com/gp/product/B081JPBJJJ…
This model is based on eedev's fan frame with the pogo pins on the side. In my case i didn't need the cutouts for the pogo pins as I was using the original cables and it was harder to print with supports in PETG. So I removed the cutouts,…
This utilizes one of the M19 threaded ports on the FormD T1 to add 10 Gigabit Ethernet using the Innodisk EGPL-T101 M.2 module. Use M3 screws to attach the ethernet port to the gasket. Make sure the screw head does not protrude past the…
Remix of Eigas original model but fits the MSI RTX 5080 INSPIRE 3X OC (the gold one). In the cover photo the thicker one is the one I remixed, Eigas is the thinner one on top.
I couldn’t come up with a decent solution to mount it to the frame, but maybe someone else can.
You can attatch a 120mm fan to the front side of the pump. If you are using FormD T1 and 120x15mm fan, GPU slot configuration has to be less or equal than 2.5-slot. You have to remove transparent cover and silvery second cover (you can…
FormD T1 Phanteks T30 Duct - Works with EIGA Shoud or Standard
It is possible to install them by friction fit or with thread-inserts and screws. I applied a soft rubber sticker as well.
Combined the two Part A BC and Part B and removed Screwhole.
A small little M19 plug with modelled threads to enable it to screw into the second rear port to blank it off. Tested on the FORMD T1 V1.1.
Finally after several trial and error, I managed to create the GPU travel kit for my GPU, which is: Inno3D RTX 5080 X3 OC (the one with vapor chamber) the 3D base model is not entirely made by myself. I tweak the GPU Anti-Sag from EIGA's…
2 small frames bolted under a desk to hold a Formd T1 pc case to free up desk space.
BOM M3 x L6 Screws (4 pcs) M3 x L8 Screw (1 pc) M3 x L4 x OD5 Heat-set Insert nut (1 pc)
Based on Andreas-Giesert 3.5" RAID HDD mounts for fan 120mm hole pattern, I changed some dimensions slightly. No it fits my needs in the FormD T1. I think it is only usable if you don't use the inside mount for the PSU.
For installation, the rubber corners should be removed from the top side of the fan for a better fit. Requires standard PC case fan screws.
A very easy adapter to use a 120mm fan on the AXP90-x47 in the FormD T1 V1.1 case that mounts to the case instead of the cooler. It is important that the fan sits directly on the cooler. I had to remove some decorative shrouds to fit the…
It's just the travel kit FormD makes but for my GPU, here's the original: https://formdt1.com/products/t1-gpu-travel-kit
V2 version, this one fits much nicer and is much easier to put on and off the case. The previous one was a very snug fit whereas this one, while still not being a lose fit, doesn't feel like you're going to pull the paint off the case. I…
This is a collapsible monitor stand to put your monitor or tablet at eye level on the FormD PC case. It holds a 10mm or 12mm thick monitor/tablet with adjustable viewing angle. The feet, 135.2 mm apart from each other ( width of FormD T1…
Mounting adapter for the IOCrest 10GBE m.2 NIC PCB. Fits in one of the 19mm holes in the Formd T1. Infill - 40% Supports - Yes, block out mounting holes Adhesion - No Print with mounting hole side flat on printbed
This is a modification of a model by Greyman . This version contains one flat side for builds which need more clearance above the CPU fan. See the original model for more details.
This design allows for more radiator tube clearance and less obstructed airflow to the radiator fan. Intended fan/rad layout is shown in the picture.
Based on https://www.thingiverse.com/thing:4728868 ! Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: DIY
This is a vertical stand for the S400. I could see a few for the S300 but decided I'd just make my own one for the S400 case as well. The vertical stand saves even more space on the desk than what this tiny PC case already saves in terms…
Three parts need to be printed and the two different small brackets dovetail/slot into the larger backplate part. This modification spaces the motherboard towards the side panel away from the GPU 6mm which allows for more riser cables…
Requires a laser cutter to cut the clear panel out (2mm thick) and needs M3x5 low profile screws to look good. The screws screw directly into the printed parts, just don't over tighten and damage the window or strip the thread. The…
The 3D base model is not entirely made by myself. I tweak the GPU Anti-Sag from EIGA's ASUS Pro Art 3D file and the Back Panel from FormD official website for the ASUS Pro Art 3D model (although the model also made by EIGA...) I build…
Some motherboards experience rubbing with slim fans in T1. However, this shroud is specifically designed to prevent such issues. It securely attaches to the underside of the fan bracket by means of direct screw-down. It is important to…
Anti-Sag Bracket for the MSI Ventus 3x RTX 3080 in the FormD T1 V1.1. It mounts to the SSD holder holes. print in PETG with 100% infill and 0.2 layer height. Needs 2x M3 threaded melt inserts (holes are 4 mm dia. and 7mm deep) the card…
Secures the other end of the GPU. BOM: 3x M3x6 Countersunk Screws 1x M3x12 Button Head Screw 1x M3 3x5x4 Heat set Insert (Unused) 2x M3 3x5x4 Heat set Insert for future proofing, in case it wasn't stable enough and needed supporting from…
This is a rear bracket for the Formd T1 v2.1 and 2.5, specifically designed for the MSI RTX 5080 Inspire. This greatly reduces wobble on the GPU especially for people who travel a lot with their PC. I use this and a remix I made of Eigas…
Could be mounted on bottom panel using m3x5 screws. Fits between reference psu mount (corsair sf750) and AXP90-X47 Using 2x nocuta nf-a4x20 got me -20C on memory in testmem5 (went from 65C to 45C on hottest stick)
A decorative yet stylish holder for psu cables and aio tubes for your formd or ncase T1, not sure if this workss with other psus
This will let you mount your T1 pc case under the desk, saving space and improving cooling.
DO NOT USE TOO WEAK USE OTHER MODEL ON PROFILE : https://www.printables.com/model/996472-s400-mini-itx-case-inspired-by-formd-vertical-stan This is a vertical stand for the S400. I could see a few for the S300 but decided I'd just make my…
I've printed 2.5mm bracket only, as seen on photos card port reachiliy is a little limited, but still works. 1mm version has even smaller width and should be better fit. Asus prime 5080 was used on the photo.
Dimensions and tolerances matched to the v2.0 VStand. Compatible with FormD T1 v2.0, v2.05. v2.1
I created adapters to tie a bc-250on a formD T1 v2.1 You need to put the 2 top on the top, under the grid cover, the first one will be at the left and the second at the right next to the top strut. Screw the top strut at the second hole…
FormD T1 Modified Spine for EKWB 3080 TUF Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 200 Infill: 100 Filament: Prusament PETG Jet Black Category: DIY
I just wanted a floppy drive to write random files to it :3 https://www.amazon.com/dp/B0D4F8VGWM?ref=ppx_yo2ov_dt_b_fed_asin_title
This should solve the alignment issues you might get with just flat screws and the standard mount that comes with the T1 and should reduce audible noise by lifting the fans and radiator as high as they can be without interference. I took…
I wanted to clean up my FORMD T1 V1.1 case and mount the SSD's next to each other. The original bracket doesn't allow this so I made this small little thing to enable that.
This piece allows a second single slot PCI card to be mounted in the FormD T1 and still be fully supported by the PCI slot in the rear. This basically just supports the tab on the metal bracket of the second card. Use a 20mm and a 6mm hex…
Travel brace for the 9070XT Reaper. The square portion is done that way to prevent brace from bending easily, and to allow users to leverage slicer capabilities to adjust the bracket offset if needed.
FormD T1 — Front Panel 3mm Power LED (USB-C Slot Mod) This is a simple mod for the FormD T1 ITX case. If you have an empty USB-C slot on the front panel and want to add a clean, custom power indicator, this model replaces the empty space…
Mount for ARGB 12v to 5v adapter . Replaces back cover, includes cable holder for the cable leading to the motherboard and extra holder for a Moddy comb from GPU. Sharing my model as is including FreeCAD files. Uses original screws for…
I wanted to hide cables and fans for an air-cooled setup. Printed in ABS-GF, which isn’t directly exposed to heat, it should be suitable for less heat-resistant materials. I simply wanted to match the shroud and it blends perfectly with…
BOM M3 x L6 Screws (4 pcs) M3 x L8 Screw (1 pc) M3 x L4 x OD5 Heat-set Insert nut (1 pc)
I believe it’s very important not to block the gap between the motherboard and GPU, since it’s the main source of fresh air for one of the 5090’s fans. I intentionally made it as air-unrestricted as possible. Maybe (unlikely) I will make…
Summary Air Kit reduces temps, fan turbulence, and GPU fan speed in the FormD T1. It contains two parts that can be used together or individually: Fan Slab and Air Block. Fan Slab Fan Slab holds two 120mm fans and two 60mm fans. It prints…
Combined the two Part A BC and Part B and removed Screwhole.
Finally after several trial and error, I managed to create the GPU travel kit for my GPU, which is: Inno3D RTX 5080 X3 OC (the one with vapor chamber) the 3D base model is not entirely made by myself. I tweak the GPU Anti-Sag from EIGA's…
Mount for ARGB 12v to 5v adapter . Replaces back cover, includes cable holder for the cable leading to the motherboard and extra holder for a Moddy comb from GPU. Sharing my model as is including FreeCAD files. Uses original screws for…
This will let you mount your T1 pc case under the desk, saving space and improving cooling.
Commercial use license version of my popular FormD T1 Exhaust Shroud Also includes .step files for easy modifications and remixing. Purchasing this license allows you to sell prints of this model on any platform (Etsy, Amazon, eBay, etc).
I changed the spacing of the part, so it fits the FormD T1 V2.5. The side struts are 4mm with this case instead of 3,5mm with the FormD T1 V2.1. The original part had exactly 4mm of spacing, but due to tolerances of your 3D printer or…
During my continuous search to improve the FormD T1s cooling, I found the fan shroud from eiga . It was too long for my and many other printers though, so I remixed it. First I needed to split up the part into two smaller ones, that are…
With this AiO Cover from FormD , you can install a full size 240mm (with up to 30mm thick fans) radiator in the top of your T1. I have described the entire process as well as temperature results on my blog tinytechtweaks.com. It's…
