Counting matching models…
If you want to use an automatic floor register, follow these instructions: Find 3D-Printed RC cars here.
Print approx. €3.53–€4.32 excl. taxPreliminary estimate for one variant
A air redirection hood for a floor-installed register. The register drops into the hood. Register dimensions supported: Above floor: 13.5" x 3.75" Duct opening: 12" x 2.25" Two options available… single piece for large print volumes.…
Print approx. €21.59–€26.38 excl. taxPreliminary estimate for one variant
Toyota MR2 Spyder HVAC knob (This may fit other Toyotas of the same gen, not sure). There is a indication hole, and will work fine as is or can put a small diffusing tape over the back.
Print approx. €1.10–€1.35 excl. taxPreliminary estimate for one variant
Ferdinand Porsche didn't like the cars in existence at the time so he built his own. We haven't built our own cars on our printers yet, but we can make replacement parts. Example: The Porsche 944 and 968 have a HVAC control that is…
Print approx. €2.13–€2.60 excl. taxPreliminary estimate for PETGSource material: PET
This has been a labor of love building this. I used an actual set of gauges and made the model a 1-1 scale version. The .stl file is 1-to-1 scale but the G-code file is scaled down to 65% as i found that was the ideal sizing for printing…
Print approx. €0.14–€0.17 excl. taxPreliminary estimate for one variant
This is a magnetically attached vent deflector suitable for ceiling mounting, too. Magnets are 8x3 neodymium, this is the pack I bought (200 for $13.99) https://www.amazon.com/gp/product/B0CCXH6W5Q I used PETG since it will have hot air…
HVAC compressor cut away model Print instructions Category: Models Summary HVAC compressor cut away model Print Settings Printer Brand: Prusa Printer: I3 MK3S </div> Rafts: No Supports: Yes </div> Resolution: 0.15 Infill: 15% </div>…
Hello folks, This is a floor register air deflector for standard 4"x10" floor registers. This is for use when a floor register/vent gets covered with a piece of furniture such as a couch. This diverter reduces the temperature…
These parts are similar to Lisle 37000 or Harbor Freight 63959 . Why buy a set when you can print the one you need? Fitting size is marked on the part. Some complaints about the HF version is that the opening is too narrow, so these parts…
The main deflector design allows for use of at 1 ½" duct hose or the secondary deflector. The duct hose option can be used for a more precise redirection of the air, such as towards a rear facing car seat or a pet kennel. The mating piece…
NO COMMERCIAL USE! Simple three-part model. Clamp your mesh between the tube and the sleeve and put your material inside. But the Hash-Vac is on top of the adapter (I made one for Dyson V8, V12, and a normal 31mm vacuum connector;…
Designed these to fit my 2000 Chevy Silverado. Pretty basic design that I thought looked nice. The "insert" was snug enough that a press fit will hold it in place with no adhesive. Use the test prints to make sure the knobs fit snug. HVAC…
OD: 3.75" The Hex Guard Window Exhaust Adapter is a highly versatile and practical accessory designed to address your specific ventilation needs. This innovative adapter empowers you to seamlessly connect your ducting to a window,…
So the A/C in my room has been underperforming for a while. The register is the furthest it can possibly be from the furnace/blower, and it's the last one in the duct system. I wasn't about to spend $30-$100 on a register booster when I…
I find it silly that I'm spending money to keep my exterior walls, doors, and windows air conditioned. Use this to send your comfortable air to the middle of the room where you need it and save on energy costs. The hole in your floor will…
OD: 5.75" The Hex Guard Window Exhaust Adapter is a highly versatile and practical accessory designed to address your specific ventilation needs. This innovative adapter empowers you to seamlessly connect your ducting to a window,…
Replacement knobs for the HVAC system, my old knobs were sticky and the plastic is rubberized. Insert is a different part to give it a different color. Remember PLA deforms under load, especially in combination with car heat. It does work…
This is a magnetically attached vent deflector suitable for ceiling mounting, too. Magnets are 8x3 neodymium, this is the pack I bought (200 for $13.99) https://www.amazon.com/gp/product/B0CCXH6W5Q I used PETG since it will have hot air…
Print this in ABS or PETG due to the temps inside of a vehicle. This should work on most Dodge Trucks. I printed standing up at .2 layer height in PETG. I used tree supports with great success. Still surviving 3 years later in Ohio summer…
I'm renovating a building which has had a small duct high velocity heat pump system installed, and there is no way to shut off some of the vents. I spent a few days making this model so I can easily connect these to the vents and now can…
This open‑source ESP32 air purifier uses a 1"x16"x25" HVAC filter with multi‑fan airflow, PM2.5 sensing, and a responsive touchscreen UI for Auto or Manual control. It pairs a compact control module with web diagnostics and tunable…
Usually one of the teeth break off over time. There are 4 gears in the unit. Check which one is broken for you. This gear is the one that drives the large gear with the lever arm. It has 13T on one end and 41T on the other end. The model…
A curtain holdback hood for a floor-installed register. The register drops into the hood. Register dimensions supported: Above floor: 13.5" x 3.75" Duct opening: 12" x 2.25" Two options available… single piece for large print volumes.…
Insert for the button port on the Volvo S40 Model can also be used as template for USB port e.g. Keep in mind that PLA deforms under load, especially in a hot car.
This is a quick design to hold Schrader caps to prevent loosing them. There is an internal cavity for a rectangular magnet. So, a pause in the slicer will be needed at layer 19 when printing at 0.2mm layer height to install the magnet. I…
These are pretty specific pieces. Not sure it is useful - maybe the Fusion 360 design files could be? This is an elbow that accepts 6" ducting on one side, and a 8" x 3-¾" opening (+ a ¾" flange and holes for screws) on the other. I have…
Built in shaper. I’m new to CAD and printing, so if you find that there is an easier way to optimize the build process, please let me know 9/13. - update. Vent with mud set frame and 10 mm magnet inserts size 14x6 10/1 - update. 12x6 vent…
hvac control knob for 2016 toyota highlander may fit other makes/models/years if printed face down it requires no support
HVAC Basic Design Register/Vent This register is an easy print for replacing your register/vent. ✅ What it does Replaces old dirty registers with one you print in any color you want Provides 4 way airflow Saves money so you don't have to…
Gear for the dashboard HVAC control unit of a 1975 Datsun 280Z
A press-fit dovetail joint splits the face plate and damper to allow common lengths to fit on most print beds. With PLA and PETG on a Bambu P1S, I'm able to join them securely without glue. I printed with default settings for PLA and PETG…
Reducers and reducer-splitters for PVC/vent-hose, originally designed to attach to an AC Infinity butterfly backdraft gate for attaching to multiple 3D printer enclosures. R4: Only 4 way splitter. Experimental. Supportless attempt. All…
My apartment doesnt have the best vent placement to effectively cool the whole room. After some quick searching and not finding exactly what I wanted, I made this. It uses 10x10x3mm magnets in the back (can be glued or just slotted in) as…
Adapters to hold a 50mm diameter capacitor in a 63mm strap and a 52mm diameter capacitor in a 65mm strap. A recent repair of my HVAC system required replacement of the start and run capacitors. Although I bought replacements with the same…
One of my semi-annual chores is opening and closing all my air conditioning vents since I have hydronic heat. Some of the vents are difficult to access and some have difficult to move adjusters. This tool makes it a bit easier to reach…
My HVAC external unit started to make weird noises because the external case vibrates a lot. Need to fix this ASAP in order to not annoying the neighborhood. External whaser need to be printed in ASA in order to last long, internal whaser…
This is a replacement lever/connecting rod for a 2006 Pontiac G6 GT temperature blend door. It's the actuator connecting rod that moves the door. I printed it out of a tough filament to ensure strength (Prusament PC Blend Natural 970g).…
I had an HVAC register which was carrying noise through from other parts of the building. This was my solution for that. It is a hook system that you can thread through a piece of foam to be able to hang it from a ceiling-mounted…
A spare part compatible with several vehicles from the VAG group. Spare part number is 7L0 907 511 AL or 7L0 907 511 E This is an enhanced version of the original VAG part. You can insert an M3 bolt through the star-shaped piece and glue…
A mod of an existing box and some generic connector brackets to contain the wiring for our furnace & heat pump. The original wiring left by the contractor was just a messy ball of twist-on connectors and it did not contain the humidifier…
Ornamental model of mixed flow fan wheel.
This is a snap in clip for the shown HVAC register vents to lock the register in the desired position and prevent it from falling to the closed position. This design has 13 notches that the damper can be set and held into, however from my…
Laser filter box made with MDF and 3D-printed parts. Uses household 12x12 HVAC filters and activated carbon. CAD included. Public domain. Use at your own risk. Pump the air outside, not into your workshop! Jeremy Cook on Substack:…
Replacement climate control knob shaft (stem pin) designed for 2003–2006 Mitsubishi Outlander models. This component connects the front control knob to the internal HVAC mechanism, restoring proper operation of temperature and airflow…
This kit is used to convert a Navi-equipped 2nd-gen Acura TL to use an Android Auto or similar touchscreen navigation stereo. Primarily, this relocates the manual HVAC controls to the original stereo location. Build thread is available…
Under-Bed HVAC Airflow Redirector A simple and effective airflow redirection tool designed for HVAC or central air systems. This part attaches to standard rectangular floor vents, guiding cool or warm air from under a bed or obstructed…
Simple diesel heater and portable AC ports for your tent or rooftop tent. The design allows for the hose insert to rotate independently of the frame and register grill. Print in a high temp filament. Supports only on the frame. Insert…
This is to help extend the air flow from under furniture.
8mm socket on the end. Hypothetically you can scale it up and down for other sizes as well. Works for all Ford, Mercury, Lincoln 2008-2011 HVAC actuator screws. Two designs but the short one worked the best for me. In the 2nd picture from…
Assembly for a ventilation flap/damper controlled by a Zigbee motor. It's supposed to be embedded into a plenum box (I made it from XPS) attached to a ducted aircon and connected to 150mm duct. The motor can be connected to Home Assistant…
In an effort to cleanup the look of the Newmar Mountain Aire dash, and to facilitate a double DIN radio, I modeled a replacement fascia to condense all HVAC controls onto a single panel. The temp controller, zone selector, and temp sensor…
If you want to use an automatic floor register, follow these instructions: Find 3D-Printed RC cars here.
Print approx. €3.53–€4.32 excl. taxPreliminary estimate for one variant
Designed this to replace my HVAC Canadian vent covers. Could not find replacements anywhere. Inner tube vent diameter 55 mm 2.1 Inch Tube Total diameter 128 mm 5 inches
A flange to fit to HVAC UV bulbs to mount to HVAC casing. The UV system that I bought (vevor) originally had flanges on the bulbs, which i used to mount to the HVAC case. I couldn't find any replacement bulbs that were the right wattage…
This open‑source ESP32 air purifier uses a 1"x16"x25" HVAC filter with multi‑fan airflow, PM2.5 sensing, and a responsive touchscreen UI for Auto or Manual control. It pairs a compact control module with web diagnostics and tunable…
2 in tall compressor model 🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with my models!
🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with my models!
Print a base, which I had to position sideways to fit a P1S. Then choose a grill design—more options are on the way. This isn’t as sturdy as a metal grill, so I suggest placing it in a spot at home where no one will step on it, but where…
NO COMMERCIAL USE! Simple three-part model. Clamp your mesh between the tube and the sleeve and put your material inside. But the Hash-Vac is on top of the adapter (I made one for Dyson V8, V12, and a normal 31mm vacuum connector;…
The coil sits on top of the furnace and can be glued into place. Optional intake and flue pipes can also be printed to add some details. 🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with…
Replacement climate control knob shaft (stem pin) designed for 2003–2006 Mitsubishi Outlander models. This component connects the front control knob to the internal HVAC mechanism, restoring proper operation of temperature and airflow…
Reducers and reducer-splitters for PVC/vent-hose, originally designed to attach to an AC Infinity butterfly backdraft gate for attaching to multiple 3D printer enclosures. R4: Only 4 way splitter. Experimental. Supportless attempt. All…
In an effort to cleanup the look of the Newmar Mountain Aire dash, and to facilitate a double DIN radio, I modeled a replacement fascia to condense all HVAC controls onto a single panel. The temp controller, zone selector, and temp sensor…
The electroluminescent backlight commonly fails on Lotus Elise HVAC panels. These can be sent off for repair, but in the meantime you have all the cables hanging out of the dashboard. The dummy panel lets you glue a scanned image of your…
Get a better grip on HVAC filter vent lever arms with this extension handle.
One of my semi-annual chores is opening and closing all my air conditioning vents since I have hydronic heat. Some of the vents are difficult to access and some have difficult to move adjusters. This tool makes it a bit easier to reach…
I couldn't find an existing HVAC vent redirect which was sized for my vent and could also fit on my printer. This model is sized to fit my vent and fit diagonally on a 256mm bed. Printed with no brim and hybrid tree supports in a tough…
Designed for Hoover Brushvac handheld vacuum cleaners. Replaces the suction intake fan. May provide improved airflow and performance compared to OEM parts. Feedback comments regarding your experience using these parts are greatly…
6" end outer diameter – 149.76 mm Oval end inner dimensions – 65 mm x 129 mm Depending on your climate you may not want to print this with PLA. Made for Panasonic FV-0510VSL1 WhisperValue DC Ventilation Fan. EDIT: included a 20 degree…
Due to the recent fires in California, we have been suffering from extremely poor quality. This caused a shortage in HVAC air filters. However, I had just ordered a new air filter for my car and realized that instead of filtering smoky…
I made this tool because the return vent in my home would hum whenever the HVAC was running. Everything I found online suggested using pliers to bend the louvers until the humming stopped. I didn’t like that solution because pliers can…
HVAC LG Remote holder for Honeycomb system, it uses screw, so you can use on other systems. You will need a hot mel nut of M3 x 3 x 4,5 and a screw of M3 x 6. Alsou going to need to print an “insert-with-M3.stl".
A design born of necessity. The floor vent in my bathroom is right in front of the toilet against the wall. In summer, the AC freezes my feet, in winter the heat from the furnace directly below scorches my toes. Enter the HVAC deflector…
Designed this to replace my HVAC Canadian vent covers. Could not find replacements anywhere. Inner tube vent diameter 55 mm 2.1 Inch Tube Total diameter 128 mm 5 inches
Using RemixerFactory's refrigerant bottle model I created this business card holder for all of you HVAC professionals looking for something unique. I printed a similar version and used tree supports. The original refrigerant bottle states…
These HVAC Collars are much easier to install and seal than the commercial ones and cheaper too. If I did it again, I would have simplified the design and square it off with 4 corners and 4 screws - but this worked just fine. Included are…
A flange to fit to HVAC UV bulbs to mount to HVAC casing. The UV system that I bought (vevor) originally had flanges on the bulbs, which i used to mount to the HVAC case. I couldn't find any replacement bulbs that were the right wattage…
VW HVAC Blower Link — Replacement Mechanical Connector (3D-Printable) This part is a redesigned replacement for the small plastic mechanical link inside the VW HVAC system . When this piece cracks, the cabin fan / heater may stop working…
Diffuser adjustment key to fit the round vent mechanism as pictured. Fits into the 23.5mm outer diameter/18.5 inner diameter mechanism. IMPORTANT NOTE: This model is just the interface. You will need to model a crude cylinder on the…
2 in tall compressor model 🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with my models!
🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with my models!
Print a base, which I had to position sideways to fit a P1S. Then choose a grill design—more options are on the way. This isn’t as sturdy as a metal grill, so I suggest placing it in a spot at home where no one will step on it, but where…
The coil sits on top of the furnace and can be glued into place. Optional intake and flue pipes can also be printed to add some details. 🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with…
The coil sits on top of the furnace and can be glued into place. Optional intake and flue pipes can also be printed to add some details. 🚨 WANT TO SELL MY 3D PRINTS? Join my $2/month Buy me a coffee membership and start making money with…
https://ko-fi.com/cristhian_godoy ⚠ DISCLAIMERS & LIABILITY Please read carefully before printing or installing: Printer Safety: Printing onto textile/mosquito net is an advanced technique. If the nozzle catches the fabric, it can damage…
🚙❄ Cybertruck HVAC to Rooftop Tent Adapter Turn your Tesla Cybertruck into a climate-controlled camping machine. This 3D-printed adapter lets you route your Cybertruck’s HVAC airflow directly into your rooftop tent—so you can stay cool in…
I have fill the arrow to it is easy to color it witch white permanent marker. Category: Other
Adapter for 3" to 4" Ducts. I made this since I needed something slimmer. Enjoy! :)
The electroluminescent backlight commonly fails on Lotus Elise HVAC panels. These can be sent off for repair, but in the meantime you have all the cables hanging out of the dashboard. The dummy panel lets you glue a scanned image of your…
Get a better grip on HVAC filter vent lever arms with this extension handle.
100x160mm sign, reading "HVAC is Cool" Mesh and Solid (may print easier) models provided. Best with color switch above 1mm, as with included gcode. Pictured in Shadowbox Frames , which fit all of my signs . If you enjoy these, please…
The knob on my Carrier Furnace 58STX045112 cabinet broke so I used my digital calipers and some Fusion 360 know-how to model a new one. I've included the f3d file for you to further optimize if you'd like but it's fully functional and…
I needed to clear my HVAC Drain that runs from my attic to outside. These adapters will hook up to a Schedule 40 3/4" PVC Drain Pipe and to your Shop-Vac, either 2 1/2" hose or 1 1/4" hose.
I made it for my stand-alone AC. Just print it twice, it interlocks with itself.
![Laser Filter With Activated Carbon and HVAC Filters [CAD Included]](https://media.printables.com/media/prints/6927bcb5-ed07-4e11-ae41-f0ddcb18e59e/images/9982080_cc72af63-387a-4a2f-95cb-abf606e4389e_b25fa928-62c9-4e1d-961f-6443bc24fa96/screenshot-2025-06-09-at-11246-pm.png)
