71 modeli
Simple mount to hold Amazon 4.5 inches strobe LED. The mount is designed for ATV 3/4 inches tube rack. Meant to be secured under the rack and to be held by zipties. I can create other models for other size tubes upon request. To have the…
In the "Multiled QT" model from the manufacturer GS Vitec, two 24V fans are connected in series. After these broke down, I have constructed a cover for a single 48V fan here. So this is a replacement part, or an improvement on the…
These strobe disks are for checking/adjusting the speed on your turntable, assuming it doesn't already have this feature. When using the applicable disk, viewed under fluorescent or other 50 or 60hz light (neon or similar) with your…
Clip to mount a strobe or similar small accessory to the bottom of a DJI Mini 2. May also be compatible with the original Mavic Mini. I designed this to mount a Vifly strobe to my DJI Mini 2 without permanently sticking bits of tape or…
A non adhesive method to mount a Firehouse 2 LED strobe light to a DJI Mini 2. This mounts to the rear top by clipping on the rear vent ports in a secure fashion. Modeled against the DJI Mini 2: https://www.dji.com/mini-2 2 LED Firehouse…
I didn't want to put the velcro directly on my drone so I modeled this and glued the strobe into it so I can remove it when I am not flying at night. This is modeled for the VIFLY strobe light, so I am not sure if it will work with other…
Malolo has created a really nice customasable case for the Raspberry Pi. I needed a mount for my Sky Watcher EQ6-R tripod so I could mount a Raspberry loaded with AstroBerry on it. I used the extra high version of the Malolo ( Malolo's…
These mounts can be used to affix strobe lights to your drone for greater visibility and to meet FAA nighttime flying requirements. They were designed for the Firehouse Arc V strobes lights, but could also be used for anything of similar…
Malolo has created a really nice customasable case for the Raspberry Pi. I needed a mount for my Manfrotto 055XDB tripod so I could mount a Raspberry loaded with AstroBerry on it. I used the extra high version of the Malolo…
A case for your Astroberry project This rugged case is for a Raspberry Pi 4B with a mounted heatsink like this one: https://amzn.eu/iCX0Fwg or https://amzn.eu/hAALRce This case has outputs for the 4 USB-A ports and the USB-C port.…
This is a smaller reflector modifier for Bowens-style mounts. The opening is 77.2mm. I wanted to mount 77mm filters to block different types of light from VIS to IR and UV. I used some 2-inch aluminum tape on the inside.
I wanted a quick-mount solution to securely mount a VIFLY strobe to underside of my DJI Avata. Velcro didn't feel secure enough. This takes advantage of the 2 little open triangles on the left and right sides of the drone. You can find…
Mounts the Vifly Strobe to the base mount without tape and at same time turns the 3 white LEDs to “legal” green for night flights in Germany which is far brighter than the single green LED on the Vifly. Works as diffusor which turns the…
A simple slide to lock in connector for mounting VIFLY strobes to any drone including DJI <250g models. Use double sided tape to connect the light top to a flat section on the strobe (battery side etc) and the light bottom to a flat…
I was tired of clamping giant gels to my lights. I made this adapter that presses into a 7" reflector. You simply cut down a Gel Sheet to 176mm and slid into place. Multiple sheets of gels can be inserted at the same time to alter color…
This is a mounting bracket for the Skyflar strobe light designed to mount to an Air Conception Nitro titanium paramotor frame (V1 and V2). Mounts to the carbon fiber spars with zip ties and allows the strobe to stick through the net and…
This is a diffuser for an Inon Z330 underwater strobe. This can be printed with tinted filament to create colored filter effects. See more on this on my blog at https://www.divetech.com/post/shooting-with-light-and-filters I printed these…
This project contains custom mounts designed in Fusion 360 for the DJI Air 3S drone and the ARC V Pro Drone Strobe Light from Firehouse Technology. The top mount bracket is printed in Overture PETG Space Gray, while all other mounts are…
strobe light clip for front arms on DJI mini mavic, mini SE mini 2. Just superglue to cheap aliexpress 2 dollar strobe, or ebay etc and clip on and off to your desire. could be glued to anything to attach to front legs.
The strobe-enhanced microscopy stage is a free and open-source workstation for imaging fast processes, particularly developed for microfluidic droplet generation. It uses the lens from the Raspberry Pi Camera to produce a microscope with…
If you use these Vifly strobe lights: https://a.co/d/1DqF4pc You can store two of them in this print for transportation. I would like to develop another outer shell to snap this holder into to cover the top. Stay tuned!
Printed in TPU as 2 parts. I fed the arm through the base, hook side first with the help of a pick backwards and then spin it around to face the correct direction. There are two bases, one that puts the strobe out front and one that has…
This is a rotary beacon model for N scale locomotives. Size is approximated from photographs and other models, so size is not guaranteed. Print the model upright with the beacons facing up, the overhang should be not terrible to support.…
This strobe allows you to know the correct speed setting of your turntable for both 33 and 45 rpm
This is a set of clips that let you mount Firehouse Technology 2-LED strobes to your DJI Mavic drone. There are 4 clips, 2 front facing, 2 side facing. Each of the “pair” is a left and right side. They mount on the arms and easily clip on…
This is an enclosure for the Flyleds.com Strobe Controller board (the current "blue" V4.0 board), which is included as part of the Flyleds "The Essentials" Position and Strobe Lighting Kit . This design was heavily inspired by one of the…
Case for Raspberry Pi 4B can be found under the name iUniker Case.…
A cover for the LimoStudio F2530 flash strobe that comes in this kit: https://amzn.to/2v4QrJH I had trouble storing the flash safely because a delicate bulb sticks out from the end. This cover protects that bulb and allows the flash to be…
I wanted one of Shire Post's strobe spinners , but for $100 (I'm sure it's worth it), I rather print one! Check the video on my Instagram page to appreciate the effect. You might be able to see it with the naked eye using a strobe light,…
I've been searching for a good, compact personal marker light to be seen by traffic or hunters when hiking in the dark and the BRDRC drone strobe off Aliexpress has proven itself to be very suitable for that task. This case allows for its…
I needed a case to house a Raspberry Pi4 and a GPS Module that I will be running Asroberry on. I found Ron's modular case for Pi's with HATs, modified it a little to remove some unneeded features, and created the modular section that…
Made a mount for the Vifly Strobe for the tailboom. Print in pale half-translucent white PLA. I find that neutral colored PLA often works very well. If you like my designs please consider donating a coffee or any amount really, I…
Inspired by a model of Jon Barron ( https://www.facebook.com/groups/2957927947836312/user/1247668582/ ) This interface can be mounted on the Retra strobe and allow to connect the OS-1 snoot on the Retra strobe. The first print…
This adaptor can be printed without any support. With M2.5 screws the RpPi4 can be directly attached, while four M4 Screws attach the holder to the scope. When using the handle or a guidescope one can use two screws for that attachment…
This model is a vertical mount for the common 6 LED strobe flashers sold all over Amazon ( this is the exact one I used ). There are two versions of this design: One that holds a single strobe, and another that holds a strobe and a 4x12…
Paramotor Strobe Version 1 isn't as bright as I'd like. Checkout Version2 Flight video https://youtu.be/buTca8\_QFGw Video of strobes in action Warning Use a 5 amp automotive fuze to prevent short circuits from causing a fire LiPo…
This is a set of clips that let you mount Firehouse Technology 2-LED strobes to your DJI Phantom drone. Works with P4, P4A, P4P, P4P+, and possibly others in the Phantom series. There are 2 different clips, 1 for side facing and 1 for…
Strobe for the AirConception Paramotor frame Warning: Strobes can snag paraglider lines which can be dangerous or even fatal. Position the strobe to minimize snags and test thoroughly before use. Strobe Amazon Part prints best in flexible…
My RPi ASI POWER Clone board for Astronomy compatible with indi-asi-power driver on Stellarmate or Astroberry Wiring diagram and PCB on EesyEDA Web control interface for ASiair (RPi 3) version. on github This web interface can be used in…
Holds 3 Vifly strobes, one model has a hole a little oversized for two 20x20x2mm magnets. I was able to cut the unused foam out of the filter set and fit the strobes in there with the mounting feet.
Basic representation of a ceiling-mounted fire strobe. I printed this as a toy for my son who is really into fire alarms and fire safety equipment, but I sized it accurately enough that it could even be used to mock up where a strobe…
Lost the button to my Led strobe controller. This replaces it. Prints well in PETG but TPU and PLA will proabably work too.…
A simple Astronaut bear I made to test my own 3d modeling skills. Feel free to take this design and make it your own!
Since i wasnt able to find something that fits my mind, i decided to remix this beautiful snap fit case. The top Lid can be installed in 2 orientations for more or less airflow. I've add the step file in case someone wants to change the…
Rubber bands not necessary to hold in the still plastic frames, so this is easier for swapping.
Use this Flash Gordon strobe light baffle to replace your damaged or lost OEM one. And who's isn't lost or damaged after 40+ years, especially when the original one is made of cardboard? Need to have supports enabled to print the mounting…
I designed this to secure a FAA compliant strobe to your paramotor frame with little to no chance of going into the propeller or snagging a glider line. Use to mount a bright white strobe or red/green flashers. You should be able to mount…
Simple L-type bracket for a round strobe light Originally made for this type of light: https://www.valostore.fi/fi/tuote/varoitusvalo_tasovilkku_purelux_strobe_round
Designed to protect the back side of Ikelite strobe during transportation and storage. Print Settings Printer: Artillery Genius Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Extrudr ASA Black Category: Hobby
I made this for a friend's RV-8, after discovering that a case he found for the original controller board was too small. This one fits the current board from FLYLED's (the blue board) and was printed on my Prusa Mk.3s in PETG with the…
My print settings: PETG 100 infill 0.2 layers Flat side down with support
The purpose of these are to shield the driver and passengers from the strobelight aimed out from the car. The angle is different between the stl-files but are made for the same strobe light bar. Depending on what window and angle you wish…
I modified the jvouillon leg at https://www.thingiverse.com/thing:2028673 . I built this item in 2 parts. This way you can decide if you want to fly mounting the Strobe Cree light holder or not, but using the same rear leg. Enjoy…
Cover for the Strobe Light of a Helicopter Kiddie Ride by company EMT (Elektro Mobiltechnik). Best printed: Upside down, Tree Supoorts for Screw Holes, 0,28 mm Layer hight
Thin shell LED light holder to make a wingtip navigation and strobe lights assembly for radio control aircraft. Fits 3 standard 5 mm diameter LEDs. I'm using this ( https://www.amazon.com/dp/B0C6V1PYZS ) lights kit. Prints without…
These strobe flash stands are replacements if you lose original ones or want to tape them to objects and don't think original needs cleaning. Students lost these all the time so I made a model not to buy one every week. Files Included…
I made this to hold the "Strobon" strobe light from Flytron, which you can find here: http://www.flytron.com/led-light-systems/99-strobon-navigation-strobe-light.html It fits in the cutout on top of the Skyhunter's fuselage which I've yet…
Paramotor Strobe Version 1 isn't as bright as I'd like. Checkout Version2 Flight video https://youtu.be/buTca8\_QFGw Video of strobes in action Warning Use a 5 amp automotive fuze to prevent short circuits from causing a fire LiPo…
Simple cover for fitting a Strix LED strobe light into the GPS bay on the Sonicmodell AR Wing Pro. https://www.readymaderc.com/products/details/strix-strobes-red Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports:…
Strobe for the AirConception Paramotor frame Warning: Strobes can snag paraglider lines which can be dangerous or even fatal. Position the strobe to minimize snags and test thoroughly before use. Strobe Amazon Part prints best in flexible…
Lost the button to my Led strobe controller. This replaces it. Prints well in PETG but TPU and PLA will proabably work too.…
Paramotor Strobe Mount using the Amazon found , PROPEL PADDLE GEAR BY SHORELINE MARINE Portable Safety Strobe Light for Kayak & Boats | 3 Modes | 360 Degrees Light Output | Water Resistant Switch | Heavy Duty Locking Pin | Boating…
Paramotor Strobe Mount using the Amazon found , PROPEL PADDLE GEAR BY SHORELINE MARINE Portable Safety Strobe Light for Kayak & Boats | 3 Modes | 360 Degrees Light Output | Water Resistant Switch | Heavy Duty Locking Pin | Boating…
Paramotor Strobe Mount using the Amazon found , PROPEL PADDLE GEAR BY SHORELINE MARINE Portable Safety Strobe Light for Kayak & Boats | 3 Modes | 360 Degrees Light Output | Water Resistant Switch | Heavy Duty Locking Pin | Boating…
If you use your Z6 for commercial, or just want to put a flashing yellow light on your mower, then this mount is designed to attach to the top lid of the bagger via 2 small mounting holes. There is a 4" x ⅚" metal mending brace from…
Outdoor Strobe Connection Box - IP66/67 Rugged, waterproof ABS/Aluminum junction box designed for safe mounting and wiri
I've designed a stand alone Green strobe light for drones powered by a 300mah 1s battery commonly used with tiny whoops and attached to the battery strap of the drone. This is a DIY Project, used to comply with EASA / UK regulations for…
This is an enclosure for the Flyleds.com Strobe Controller board (the current "blue" V4.0 board), which is included as part of the Flyleds "The Essentials" Position and Strobe Lighting Kit . This design was heavily inspired by one of the…
The purpose of these are to shield the driver and passengers from the strobelight aimed out from the car. The angle is different between the stl-files but are made for the same strobe light bar. Depending on what window and angle you wish…
If you use your Z6 for commercial, or just want to put a flashing yellow light on your mower, then this mount is designed to attach to the top lid of the bagger via 2 small mounting holes. There is a 4" x ⅚" metal mending brace from…
