Liczymy pasujące modele…
Heads-up News Heads-up #1: there’s a newer version of this here: https://www.printables.com/model/1247920-new-v30-of-top-riser-set-for-flashforge-adventurer Also, heads-up #2: There is a helpful new “guard plate” improvement remix…
How to use the 'All Files' choice "Download All Files" gets everything — including the .3mf file — named " ad5m-minimal-enclosure-by-design8studio-for-orcaslicer-230.3mf " — which is an OrcaSlicer project file , containing multiple print…
NEW The new remix prints as one piece, not two, with no supports needed, and this eliminates an intermediate step of gluing two parts together. Kudos and thanks to WingWong (@WingWong_521453) for the idea. I'd have just used his remix,…
I needed to save space and access the filament easily. I created this :-) (easy to print NO raft or support needed) 15% infill should be enough. It mounts on the right side top! Works for both - small and normal 1kg. filament rolls. 𝔗𝔴𝔬…
An extruder guide for Flashforge Adventurer 5m Pro to avoid scratches on the inside of the cover. The bottom part is made flexible to follow the extruder tube in any direction, while at the same time hold it down a little bit. Make sure…
VIDEOS These two short videos explain everything: NEW New as of January 28, 2026 — The following additions and improvements were made: Now the boxes can be mounted on the sides of the printer. Click here: New as of January 27, 2026 — The…
Improved version with display installation from the inside (without frame). _____________________________________________________________________________ Enclosure with 4 mm polycarbonate sheet panels https://a360.co/47jcXw3 . The purpose…
Disclaimer: Before you start doing anything with electrics, make sure that you understand what you are doing and comply with all conditions for your safety, the safety of others, as well as the safety of equipment.…
I've remixed this from the original one-piece model I found and sectioned into 4 pieces, 2 pieces per plate, this lid riser for the Flashforge Adventurer 5M Pro. Without the riser, the filament tube rubs on the clear plastic lid. I had…
Flashforge AD5X Spool Number Plates, shaped to the spool spindle ends. Useful to show spool number which is hidden if the spool is installed Just clips in to existing spindle hex hole at the end. Remove number support after printing with…
I didn' see one of these for my printer, so i used stonegas's file and remade the lower brackets to fit the A5M Pro. This model fits inside the frame where the top cover goes and uses 608 bearings just like the original. Included the STEP…
One wall on first layer, enable support, easy print Holes for 5x3 magnets and self-tapping screws for fan mount (07/02/2025 New toolhead designs uploaded) (05/02/2026 New toolhead designs uploaded) (05/05/2026 New toolhead designs…
I wanted a base for my AD5X that would route the power switch to the front of the printer and add storage for tools. I wanted a lip around the corners of the printer to help ensure the printer did not wobble off, but I wanted to retain…
NEW Makes it so part prints as one piece instead of two, no supports needed, and this eliminates a step of gluing two pieces together with CA glue. I'd have simply used the remix of my design by WingWong (@WingWong_521453) but his caused…
V2: Remixed David's newer chain since I was having sag problems. Remodeled it and raised it up by 8mm. STL is already in correct print orientation.
Spool holder for the Flashforge AD5X inspired by the great "Filler" spool holder. I was originally going to just modify the filler, but found that there were no .step files for the parts I needed to modify, so I just started from scratch.…
*This is a work in progress* I'm looking a way to atach the mount to the chasis but there's a few whitout making a hole in the base I use this aux fan from bambu lab…
Hi there! Just a fun screen surround I mixed. Fits snug, includes a wizard to accompany you on your journey =). <3 to Ninomalbinho and isod
needed a riser for the lid to the enclosure as I grew tired of comsntantlty taking it off and putting it back on. this minimises drafts whilst maximising air flow. even with the wobble it doesnt fall off and you can move it side to side…
I used the original part for 2 months, but now I need more space behind my printer. So I created these two versions based on the original design. Changes: - Thinner walls (1 mm and 1.5 mm versions instead of 2) - Simplified geometry -…
This is a modified version for the very common light bar used on Flashforge AD5M and AD5X printers. Includes a secondary cut-out so that desoldering will not be necessary. Also lengthened the ends to allow the 230mm long light bar to fit.…
Remove standard foot, Keep original screw, Fit top half of foot to the machine, Press in the bambu style dampening rubber, Press on bottom of foot. If everything printed correctly then it should fit tightly together and not fall apart if…
This goes with the previous fan spacer I made for the 5M (not the PRO) to go between the lower filter fan and the back cover vent holes. I designed it to work with TPU, and that's the filament I have tested it with. The spacer slides over…
This is a 2x1 Gridfinity bin with special cutouts to hold two Flashforge AD5X nozzles. The nozzle size labels can be easily swapped below the nozzles to match your collection. Thanks to Jimoreno for the original design.
I wasn't pleased with factory filament hangers, as I couldn't use 2 rear ones, so I redesigned it. Makes possible to have the printer closer to wall. The assembly can be made with 608 bearings or 635 bearings. Depending on the bearing…
Alternative Dry Box Plug (Easy-Print PLA Design) This plug is designed for the FlashForge dry box as a simpler, more print-friendly alternative to the original TPU plug . The geometry has been intentionally simplified to reduce overhangs…
Unzip and import into Flash Studio for a better printing experience. feet are a direct replacement, use original screws and washers
Ein offenes System samt Toolbox und Sprühdosenhalter für den Flashforge Adventurer 5M Pro. Es sind sowohl Halter (Haken) für die Seiten (kurze Version), wie auch für die Rückwand (lange Version) enthalten. Wie immer ist das Projekt offen…
I found that the purge that the Adventurer 5M does when swapping filament wastes to much filament. This is about the bare minimum to get the filament through the hot end. Hope you find this useful! :)
With the new Raspberry Pi Zero W (Pi0W) having been released, I decided to design a case and camera mount for my 3D printers. And what a better day to release it than Pi Day 2017! This should work if you don't have the front acrylic panel…
A bin that is thin and yet long and tall to fit behind the Flashforge AD5X. Just glue in 4 10mm magnets to allow quick removal and replacement. The bin stands off away from the back of the printer to allow proper ventilation. No brim…
i finally got sick enough of needing a flashlight to see printed material behind where the toolhead happened to be that i decided to do something about it. none of the other models i found suited my needs, so i made my own using parts…
Фильтр для 3D принтера Flashforge AD5M печать выполнена PETG ,но лучше будет из ABS (заполнение корпуса и крышки Героид 18-23% ) 4 периметра , 4 слоя крышки, 4 слоя дно вентиляторы 5015 24v х 3 шт 4 винта М3 х 8 мм 4 втулки вплавляемых М3…
I modified the SpoolHolder_v8 so I could use wider spools such as Amazon Basics brand. Print Settings Printer: FlashForge Adventurer 3 Rafts: Doesn't Matter Supports: No Category: 3D Printer Parts
Small pocket style handle for the front door of the Flashforge Adventurer enclosure.
Check out my new Bed Levels ! This is a test print I made to help level my bed while it's printing. It is currently made to fit a 225mm x 145mm bed, which would cover the MakerBot Replicator Dual, FlashForge Creator Pro, PowerSpec Pro 3D,…
I was building a BENTO box filter for my AD5x and discovered the print bed would clip the bento box with the original FlashForge Adventure 5M BentoBox Fan Duct. It is strange this occurred as the 5M and AD5x should have identical…
Modified the AD5M mount to have access to place a switch to turn on the filter. Also removed the left side cutout for a cleaner look since I was only going to use the right cutout. Dimensions of the switch cutout: 19mm x 12.7mm Printed in…
Gridfinity based Flashforge 3D Printing Adhesive holder 1x1.
Add a bit of style to your display screen with this switch surround. This still allows access to the USB port on the right. The kids / grandkids will love it. 3 plates Total print time - 1hr 31m Total filament - 44.38 g 0.2 Layer , 2…
I could not find any nozzle cases that fit the Phaetus and off-branded nozzles so I remixed Doug Joseph's nozzle boxes to fit these different nozzles. Printer settings are the same as the original. 10% infill on lid 15% infill on base 2…
Update: Created V3 that combines the 2 parts for the threaded shaft into a single part - I actually had printed it that way originally just joined the 2 parts in the slicer but no reason to have them separated. Update: Created V2 that…
Bed leveler for FlashForge Creator Pro 2 with dial indicator OR caliper. Does not work on Creator Pro. The 2 is a bit wider. Inspired by https://www.thingiverse.com/thing:1502857 Parts: M3 heatset inserts:…
These are a few parts to make a single-extruder conversion for the old FFCP printers. These are very easy to print. No supports needed and you can use all existing screws and mounting positions.
This is a webcam holder designed for the Flashforge AD5X 3D printer. It is primarily made for the Logitech C270 , but can also be adapted for other similar webcams. The mount can be used together with the original Logitech C270 mounting…
Flashforge mod for ERCF v2 featuring an entry sensor Pneumatic valve connector ensures filament doesn't pop-out during filament changes Entry sensor gives Happy Hare an additional sensor to work with during filament changes. Installation…
Adapter for Flashforge Creator Pro 2 original spool holder This adapter mounts to the original spool holder allowing you to use third party filament reels
This is 7mm longer to be able to use the tool holder with a 5M Pro
Redesigned extruder block with smaller drive gear hole (11.8 instead of 13 mm) -> longer filament support between the drive gear and hot end so flexible filament does not get stuck in between. As CTC that I own is an Makerbot Replicator 1…
These are some test prints I made to help level my bed while it's printing. They are currently made to fit a 225mm x 145mm bed, which would cover the MakerBot Replicator Dual, FlashForge Creator Pro, PowerSpec Pro 3D, etc. It helps to see…
This is a 2x1 Gridfinity bin with cutouts to hold two Flashforge AD5X nozzles - and two lid options. Thanks to Chir and Jimoreno for the original designs.
This dial gauge holder fits beautifuly ontp the extruder guide raills and quite impressivly doesnt allow it any wiggle room at any point. i knocked this up in ONSHAPE as basic functional and very easily printable.. 0.4 nozzel used /0,2…
UDPDATE ADD VER Engine Bracket AXIS V2.1 Engine Bracket AXIS V1 Model The X bracket differs from the original one. It does not hang in the air. The length of the guides has been increased ----What do you need----- 1.Insert nut M3*4*4.5…
Foot for the FlashForge Creator Pro Printer. STL and SolidWorks files included.
Remix Filament Motion Sensor for Flasforge Adventurer 5m Оптический концевик (такого вида: https://aliexpress.ru/item/1005002327282237.html https://aliexpress.ru/item/32602153500.html) Комплект BMG шестерней, можно самых дешевых…
I saw studiohals' spool holder for the FlashForge Dreamer. It didn't quite work for the FlashForge Creator Pro / PowerSpec 3D Pro, so I remixed it. This is made to use the spool holder that came with your printer already. To load…
Flashforge Creator Pro 2 Wildone container holder Windone container : https://www.amazon.it/dp/B07L2QJ5LB?ref=ppx_yo2ov_dt_b_product_details&th=1
"why another filament holder???" Answer: "because most are difficult to print and/or not strong enough and/or do not fit the Flashforge Creator Pro" So here is a filament spool holder that can work on its own, due to a standard M4 hole…
This is the window by flashforge creator pro with pro tool caddy, with a part that closes the printer to helper print abs require : 2 screew 3.5 x 13 mm Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes…
Fits over an empty extruder mount. This will not work with both extruders. Still working on a simpler image/sketch to gcode process, will update with those details shortly. In action: https://www.youtube.com/watch?v=ebXGa1y9DEg 2x 12mm M3…
Over time, the rubber feet on the FlashForge CreatorPro start to degrade, leaving black residue all over the place. I designed these foot booties that slip right over the outside of the rubber feet, solving the problem easily. NOTE: These…
I don't charge for my functional models. Please consider purchasing some of my paid models as a way to support both my work, and this great website: https://www.printables.com/@ninjamida/store Modified print head for the Flashforge AD5X…
New spool holder for old-type (wooden) Flashforge Creator. Fits standart 1kg filament spools. You should rotate holder model upside-down in your slicer. Print Settings Printer Brand: FlashForge Printer: Creator Pro **Rafts:** No Supports:…
FlashForge Creator Pro - SD Card Cover keep junk from getting in the hole Add another file (before slicing) and position it above the card cover file for a different look! Do not print FFCP-SD_cc_assy.stl as it is only for assembly…
needed a riser for the lid to the enclosure as I grew tired of comsntantlty taking it off and putting it back on. this minimises drafts whilst maximising air flow. even with the wobble it doesnt fall off and you can move it side to side…
Переделка оригинальной зашивки от Flashforge . Все панели печатные, так же добавлено боковое крепление для катушки, интегрирован датчик температуры и влажности, добавлена панель под 4 сенсорные кнопки для управления различными функциями -…
I decided that the clip on filter covers were a good spot to place a cheap hygrometer I had laying around. I am using it more as a chamber temperature sensor. There is a bottom or top mount for the cover. Cover should fit any of the…
I was having issues with the front corners of magnetic build plate lifting up during prints that span most of the plate, so I made this clip to hold the front corners down. The hole on the bottom of the clip is so it attaches itself to…
Модификация системы обдува 3D-принтера Flashforge Adventurer 5M Modification of the Flashforge Adventurer 5M 3D printer blowing system Печатать без поддержек и отключить замедления на внешних периметрах Print without supports and disable…
One wall on first layer, enable support, easy print Holes for 5x3 magnets and self-tapping screws for fan mount (07/02/2025 New toolhead designs uploaded) (05/02/2026 New toolhead designs uploaded) (05/05/2026 New toolhead designs…
PETG, 3 walls, 100% infill, the part is originally upside down so flip it in the slicer to print correctly
Уменьшение стука стола при Z-HOPE: фиксатор гаек ходовых винтов. Нужно два фиксатора на передние стойки (-SIDE) и один на заднюю (-BACK). You need two retainers for the front struts (-SIDE) and one for the rear strut.
This is designed to work with the Adventurer riser lid enhancements for gluing purposes. It will allow you to align your parts perfectly for gluing them together. I didn't like the fit of the model so I cut off the tabs and reprinted them…
This is an improved Riser for the FlashForge Adventurer 5M Pro. I made the fit better and removed to tab slots that didn't work for me. The front sides have 2 x 5mm dowel holes and 2 dowels. The rear sides include the 3 rectangular plugs…
Printed with ASA and 0.4 nozzle with 0.2 Layer height.
UPDATE: Updated the text on the model. Still working on a newer version and a non gridfinity version. Just don't have the time to finish them. I saw Flashforge had .25, .4, .6, and .8 nozzles for sell on Aliexpress, so I decided to make a…
i finally got sick enough of needing a flashlight to see printed material behind where the toolhead happened to be that i decided to do something about it. none of the other models i found suited my needs, so i made my own using parts…
How to use the 'All Files' choice "Download All Files" gets everything — including the .3mf file — named " ad5m-minimal-enclosure-by-design8studio-for-orcaslicer-230.3mf " — which is an OrcaSlicer project file , containing multiple print…
Adapters that allow the assembly of external electronics, replacing the original one, using a raspberry, SKR Pico for the MCU and an EBB36 for the Headtool. the porting manages to recover all the functions or at least that is the goal. to…
After printing the enclosure for Adventurer 5M I hit the infamous problem of filament sensor which is not working in reverse direction. I disassembled the sensor to figure out why this is happening. It turned out, that the metal bracket…
Spool holder for the Flashforge AD5X inspired by the great "Filler" spool holder. I was originally going to just modify the filler, but found that there were no .step files for the parts I needed to modify, so I just started from scratch.…
LED strip mount for Flashforge Adventurer 5M https://www.printables.com/model/1339050-channel-for-the-led-wire-fa5m https://www.printables.com/model/1339884-xl7015-led-ffa5m
Flashforge AD5X Spool Number Plates, shaped to the spool spindle ends. Useful to show spool number which is hidden if the spool is installed Just clips in to existing spindle hex hole at the end. Remove number support after printing with…
I used the original part for 2 months, but now I need more space behind my printer. So I created these two versions based on the original design. Changes: - Thinner walls (1 mm and 1.5 mm versions instead of 2) - Simplified geometry -…
HOTEND HOLDER for Flashforge Adventurer 5M / 5M Pro It sticks to the wall with double-sided tape
Box s úchytom na odpad filamentu pre 3D tlačiareň FLASHFORGE AD5X
If you have a Flashforge Adventurer 5M, you likely noticed that there are bays in the back for a filterable exhaust. I didn't really feel like going down a rabbit hole of hooking up fans to the printer's power supply, as I just got the…
ENG - A basket and slide to capture the excrement of Flashforge 3D printer filaments. It is quite narrow and equipped with a removable basket, so the printer can be moved against a wall. The slide has been designed with grills to remove…
This print is designed for TPU. If printed in a rigid filament, this will likely only cause issues. An expedient strain relief/ cable erector to keep the AD5X Print head cable from getting caught behind the print head with the IFS moved…
Simple design for Flashforge AD5X Spool holders, adding numbers to them to avoid confusion while loading filament. Just push the number to correct position and remember the rod has a hexagon shape, so you might need to rotate the number…
Noticed that whenever you print the enclosure your alway left with the bottom part below the door being black and not matching the rest….. So I gave quickly designed a bottom trim to go over it, I did recess some holes into it for magnets…
I know you all wanted this. Here is the Flashforge print nozzle storage box with the finger grabs AND the Flashforge logo on top of the lid. The “F” of the diamond logo is separate so you can infill it with the FlashForge blue if you…
Flashforge Adventurer 5M Pro – Toolholder This print in place toolholder allows you to store your standard tools neatly on the side of your Flashforge Adventurer 5M Pro. No glue is needed: everything just clicks together permanently. Fits…
Original Idler Bracket for Flashforge Adventurer 3 Y-axis / Bed. Reverse engineered with manual measurement for upgrade purpose Recommended Print Settings: Material: ABS Infill: 100% Assembly Guide This part can be found near the rear of…
This is a clip to hold the toolhead electrical cable using the PTFE tube. Compatibility with all Adventure M5 printers: Flashforge Adventurer 5M Flashforge Adventurer Pro Flashforge Adventurer AD5X
I made a edit to the standard frame piece that holds the control panel to add a name plate. The nameplate consists of the back place, a ring, and the 4 letters of the printer name. Bringing in the 6 elements together into the slicer as a…
