Liczymy pasujące modele…
Update 7/17/24 Added PEI texture Import the new PNG override the old one change bed shape to x:220 y:244 paste 0x0, 0x12, 220x12, 220x0, 0x242, 0x232, 220x242, 220x232 in exclude bed area section ( print area remain 220mm/220mm ) Import…
UPDATE:8/9 added a bowden guide so filament enters extruder straighter. was having issues with loading new filament where it wouldn't be grabbed. UPDATE: Made the nut thicker so doesn't slip as easy. slap a zip tie on it once snug Update:…
Plug for the hole on back when relocating spool holder. Printed on Infimech TX default TPU profile + tree supports
Sandwiches between printer and whatever you are using for exhaust. Help keep the heat in for abs/asa but let it out for pla
This storage bin hangs delightfully off the top of the 3D printer, zero tools necessary. There are two separate models, one for the bin itself, and the other is for the hooks to hang it from. These can easily all fit on a single build…
8/31 added model for v2. makes use of the different hole pattern Super simple wall to section intakes and out takes. In stock config the heat exhausted from the PSU gets sucked right back in. leaves about a mm under it. Including step so…
This spool holder hangs off the top of the printer, allowing you to mount your spools on the side of the printer. Depending on your setup, it might be better for your material to be on the side of your printer, instead of the back.…
Update 7/14/24 Updated the door latch now door has no wobble during print. now door latch can snap on the screw, so no need remove whole side panel. ___________________________ Update 7/15/24 Minor improve on the hinge insert nut…
Update: minor adjustment to fan bracket so there is a little overhang to help guide air. Will need supports on print. Since getting parts from Infimech seems difficult, and they aren't listing the aux fan anymore, I took matters into my…
Bracket to relocate filament runout sensor to work with filament relocator . Will have to extend wiring by a few inches. Gromet Plug for old spool holder Alternative top hat
A replacement for Infimech TX (Flying Bear S1) factory filament sensor case. Stock sensor case have strange design decisions like parts of ptfe tube inside, which leads into annoying jamming issues during filament change. Sensor itself is…
Relocates spool from back of machine to left side. uses a small length of PTFE tube. Will need slightly longer bolts. Filament sensor relocation bracket is also needed. Grommet Plug Alternative top hat
Print in ABS/ASA or better because of heat. Reuses the fans that come on it or get some new 4010 blowers. 2 10-15mm m3's to attach to back of hot end. 2 tiny self taping screws to attach fans to ducts/bracket. Organic supports. Set to…
Goes together more or less the same as V1 but now takes 5015 blowers and has less pieces to /print. 2x 50150 blower fans acid free carbon 2x m3 heatsink message me if you want the multicolor model Join the discord 9/10 EDIT : redesigned a…
Update: added a passthrough that uses 1x 2 pin and 1x 3 pin jst connectors. Kinda of a PITA to get them in but they are supposed to be a friction fit. Will need a little soldering Easy and quick TPU grommet for where the wiring comes out…
This is a lid support bracket for the Infimech TX. Without the brackets, the lid would have to rest against a wall, or completely removed. This allows me to just flip the lid open. Mounting uses the original two button head screws on the…
Lid alignment tabs for the Infimech TX. Print two and use the existing screws to mount. This is totally unnecessary unless you have OCD like me and hate to see the lid crooked. I also used small binder clips to pin back the velcro tabs up…
這是用於 Infimech TX 的插座，帶有 m4 嵌件。
This is a light weight extruder using HGT internals. Over 70g Lighter (see photos) BOM: 2x M4 heatset inserts 2x M3 heatset inserts HGT extruder - and accompanying hardware A 10 tooth nema 14 like this one Direct swap, though you will…
Designed and created a filament sensor that sits on top of the InfimechTx's extruder. I was tired of reaching around the back to manually feed filament through the stock sensor. Moving the sensor to the extruder allows easier access and…
same install as the other one but uses 2 608 bearings for low resistance on reverse bowden. use organic supports for main body and regular supports for roller
Clip for attaching PTFE to the Cable
holder for attaching a plastic coil inside the printer without drilling holes
The spool holder can be printed with a 0.2mm layer, with supports on the screw part. The nut is recommended to be printed with a 0.15mm layer. For the model in the photo I used orange Prusament PETG with 4 perimeters and a 20% Gyroid…
Corner brackets to mount 4x HSW panels to side of TX. Should fit either side. Uses the lower top and upper bottom bolts in the corner extrusions. No need for additional hardware 4/20 - was pointed out I had the wrong grid. updated to 8x8…
Might not be needed, it's even detrimental because you loose 3mm of z height but you won't get bits of filament and dust in your z motor. Print 2 pieces. Print settings: 3 walls 15% infill 5 top layers Supports : Normal (auto) - Snug
I designed a small tool organizer for the hex keys, the pliers, the tweezers, the little screw driver, the nozzle cleaner, the spatula and the extra screws. I also added space for a brass bristle brush and a small cutter. I printed it…
a bit better views than the stock camera position, requires a m4 screw that is a bit longer than the stock one from this part of the machine (pic below) for enclosure the USB cable gonna block the max X,Y movement a bit at this specific…
Another variant of lid support brackets, to set lid open without relying on nearby wall. This one uses side sheet screws to mount without touching main frame screws. Also there is 0.2mm membrane on one of the holes to print without…
UPDATE: Supports for back of machine The only real printed part is the backer for the hinges. Parts list; 14x14 acrylic top PTFE passthrough Hinges Some 20mm ish m5 bolts and hammerhead nuts 5mm heatsets Need a heatset press ? I enlarged…
*** V2 out now!*** 9/17: Carbon chamber got the same treatment as v2 which seems to work better. Will fit existing fan housing and face Carbon Filter/Recirculation Fan for Infimech TX. Photos show install. Could be mirrored to run two on…
This mod for the Infimech TX was in the making for some time. I didn't really like the top hat with which it came but I understood its purpose and the cost saving it brought to make this great machine affordable. Being a 3d printer it…
A small upgrade for the Infimech TX/Flying Bear S1. It's an articulated hinge that allows the door to swing open to the side of the machine. You will need: • 8 x M3x10 screws and 8 x M3 nuts, 4 screws and nuts per hinge • 4 x 2mm pins…
The stock filter kinda sucks. This works waaaay better. 2x m4 heatsets 2x m4 x 35? bolts. I bought 45mm and cut about 10mm off 4" dryer venting I use an inline fan like this I keep the fan as low as it can go and its still a little cold…
Full housing for 120mm fan and adds the ability to have a HEPA recirculation filter. Takes GL-2103 filters like these . can be run as aux blower, aux blower with HEPA, or just HEPA recirculation with fan duct removed. I am told the duct…
this is a work in progress. the product does function as it is. all holes are tapped by the screws when putting it together. currently i have printed in asa and it worked but did eventually fail. Printed horizontal with supports if…
Supports for Acrylic lid . Print 2. Attach to two screws in top left and right corners
Initially I made the spool holder mod for my Infimech TX Top hat and liked it for the ease of loading and unloading of the filament and decided to port the idea for the people that do not want to make the Top hat. It's untested but it…
отверстие 4 мм. установка гаек м4
This is a modified retaining ring for Ender 3 / CR-10 style ball-bearing spool holders. The ring is a few millimeters thinner to accommodate the thicker panels of the Infimech TX. Amazon link - Example spool holder
Adhesive bottle holder for Infimech TX/Flyingbear printers. The maximum diameter of the bottle is ø50mm . It is recommended to use supports as shown in the photo during printing. The width of the wall where the holder is attached is 2mm .…
A modified version with two springy tabs, enabling printing with PETG.
Was asked to make an adapter for the BIQU Nebula extruder for the TX. This is what I came up with. Only have the cad to go off so may need some tweaks so .step is included. Have not printed or tested anything, but should be close and a…
I love the glass door on my Infimech - but I'm always paranoid I'm going to break it while working on the printer. So I hacked up a quick set of replacement hinges to allow the door to be lifted on/off the printer. EDIT 10/10/24: Lost the…
Problem: I encountered difficulty loading filament through the standard sensor. This was especially true for filaments of non-ideal shape — cut, broken, previously extracted, or bent. Solution: I designed and manufactured my own sensor…
Progress LED Status Bar for Infimech TX / Flyingbear S1 LED status bar for a Klipper-controlled 3D printer, inspired by H2D. Displays real-time printer state, print progress, and bed temperature. The project works out-of-the-box — no…
It all started a few nights ago when I was print something and all of a sudden I heard something strange coming from the direction of the printer, checked the print all good. Went away minding my business and again… what the hell… Stayed…
It's a remix of the original mod from @WorronRD_2591147 with a small addition of an override option. As shown in the photo, a piece of blue filament is sticking out from below, and the LED is on, even though no filament is in the tube.…
I made Hula inspired feet for my machine, but it can be adapted to be used on onther machines as I included a step file for easier design. I user 6mm steel balls for rolling, PETG for the structural parts and TPU for the damper and the…
I created a carbon and HEPA filter for the TX. I used 2x5015 fans to help evacuate the air from the enclosure in the room. The system features a modular approach with quick-release latches. For the HEPA I settled on this ones and used 2…
Was asked to make an adapter for the BIQU Nebula extruder for the TX. This is what I came up with. Only have the cad to go off so may need some tweaks so .step is included. Have not printed or tested anything, but should be close and a…
