Liczymy pasujące modele…
I've been working on utilizing Pico remotes to control Zigbee lights through Home Assistant , and I wanted some additional wall mounts for the extra Pico remotes that I wanted to install, so I remixed joshcarter's original wall bracket to…
Pico remote slides onto the pedestal and clicks in to lock in place. The model also has holes on the bottom to allow for recessed rubber bumpers to give the pedestal some grip on the table surface. As pictured, stand was printed without…
A wall mount for the Lutron Caseta hub! Clips over the whole hub. There are four holes, but I'm only using two myself - it was mostly just more convenient to make 4 holes than 2. Category: Electronics
I made a few changes to dancerdude's model to more accurately fit electrical boxes and the pico remote. Adjusted screw spacing to match standard box mount and strap mount distances. The original model was close, but not exactly right.…
I decided to adapt my Lutron Pico wall plate bracket into a desk stand. This uses the mounting slot on the back of the Pico remote, so it's easy to attach and remove. The body prints in one piece, and I've included supports which work…
Pico remote slides onto the pedestal and clicks in to lock in place, 8mm rubber feet fit perfectly in recessed holes on bottom. Printed in PLA 0.1mm layer hight.
This is a replacement for the Lutron Caseta Pico wallplate bracket. I was installing a bunch of remotes and, of course, came up one bracket short... so here's a replacement that has the same basic dimensions as the Lutron bracket. Unlike…
This is a remix of the original wall plate mount bracket with the following improvements: Remote holder part now has more material and is stronger. Remote holder part now has a lip to hold the remote once fully inserted. Remote holder…
Just wanted to organize my setup a bit so i took some time to design this.
There are two version available: one with , and one without screw holes. The one without screw holes is meant to be mounted to a flat surface using a double sided tape such as 3M command tape.
Main Piece This item includes several options for mounting your Lutron Aurora Philips Hue dimmer. Lutron sells a “L-AWALL1-WH” plate for mounting (intended to mimic a “traditional” switch that the Aurora can mount to natively), but this…
I had the idea to mount a servo motor to the faceplate so I could use Alexa to control it to turn on the fan or lights in my room. This faceplate is the first step for my idea. I figure if anyone's faceplate snaps while removing theirs,…
Lutron Caseta Smart Hub (formerly Smart Bridge) holder, wall mount. Several versions, mount with screws 40mm apart or command strips. No supports needed. Print on edge as pictured. Edit: Etched version added. Label available for painting…
Simple Lutron Caseta Pico remote (Model PJ2-3BRL) wall mount holder. Double sided tape or Command Strip would work best to mount. Credit goes to ccmake: https://www.thingiverse.com/thing:5383306/files
In a new house I've been moving some light switches, and one dimmer is without a knob on the slider. A classic application for 3D printing. Rather than design a new one, I found @kg333's fine model and started there. I'm a fan of…
This is a lutron caseta pico remote mount so you can mount your remote to any surface using double sided tape prints in 14 mins !
This desk stand for your Pico has a wide base to give it stability, and uses the mounting slot on the remote to lock into place. There's a lot of chamfering for easy handling. Update 2024-01-29: I've added a new style that is slightly…
The Lutron Aurora is intended to be mounted on top of an existing light switch. I designed this wall mount because I wanted to mount mine somewhere where there was not an existing switch. I've included two versions: (A) has a smooth back…
I created this so I could easily wall mount my Lutron Aurora dimmer using double sided tape. It fits into the existing Aurora base and provides more surface area for tape to stick. Could also be used for extra stability if you were just…
This is a sleek wall mount for the lutron pico remote available in various configurations. Adding a magnet to the top back portion will firmly hold the remote in place and allow for easy pull out for on the go use of the remote. Or you…
This is a vertical stand I made to consolidate my Philips Hue Hub, Lutron Casetta Hub, and my Smartthings v3 hub.
There are a few Lutron Caseta Hub/Bridge mounts you can find, but I wanted one with flange mounting options that keep the screws away from the body of the Hub/Bridge. I drew this from scratch in Fusion 360 (I'm still learning) and then…
Print on flat side. No supports needs. For spacers, adds a gap between wall and faceplate for when you need a little more space inside. For backplate, this is to replace one if you need it. Tip: Let it cool down on the build plate before…
This is a surface mount adapter that will allow a person to mount a Lutron Caseta remote to any surface. I mounted mine with 3M double-sided tape.
A simple holder for Lutron Caseta remotes I printed it at: 0.2mm Quality, 15% infill, Gyroid Hope you enjoy!
I needed a new knob because I replaced the switches in my house to white ones. There was nothing wrong with the dimmer, but it had an ivory knob. I couldn't find a replacement knob in white. My only choices were to buy a new switch with a…
This is a remix of the Lutron Pico Double Remote Stand Pedestal by justinsmonty to include 3 Pico Remotes for those of us that need a stand/Pedestal for more than 2 Remotes. This Model can also be found here…
Reference model of a Lutron Caseta Smart Hub Model (L-BDG2-WH). Made this while designing a rack mount cage for it.
I live in an apartment so I don't want to mess with removing the paddle switch so I designed this to replace the decorative plate and simply install over the paddle switch. No need to mess with electrical wiring. Update 9/13/22: Slimmed…
@EvilProphet made a really nice system called ESRack. Expanding on it, as it rocks The ESRack system includes the following components: Mounting Brackets - used to install the unit in the rack, available in 3 sizes: Short Medium Long…
This turns the Leviton Decora Screwless Wall Plate into a Lutron Caseta Pico remote holder! I really like these Leviton Screwless covers, but I've been slowly adding smart lights that I want to control with the Lutron Caseta Pico remote.…
Remix of the single remote stand available from https://www.thingiverse.com/thing:2587272 This one provides 2, 3, and 4 remote options. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15mm Infill:…
Buddy wanted to wall mount one of his remotes and couldn't find the flush mount that came with his, which is how we find ourselves here. May your print times be short, and your remotes magically afloat.
This is a slightly tweaked replica of the original Lutron Pico Remote Pedestal. You will need a couple of M3x8 screw to attach the remote mount to the pedestal body. An M3x10 might work too but I haven't tested. The two screw holes are…
This is a remix of the Lutron Pico Double Remote Stand Pedestal by justinsmonty to include 4 Pico Remotes for those of us that need a stand/Pedestal for more than 2 Remotes. This model can also be found here…
This angled wall-mount bracket for your Lutron Caséta Smart Motion Sensor (PD-OSENS or PD-VSENS) allows you to set it up at an angle on a flat wall. In the second picture, you can see the original and my angled version side by side. So…
Here is a wall mount for a Lutron Caseta Pico Remote Control ref. PJ2-3BRL. Can either be screwed on or -preferably- with double sided tape. To be printed upward. The dimensions are perfect, neither to snug nor too lose.
I wanted to get this Lutron remote off of my desk so I designed this holder to that I can store and use it on the SKÅDIS board I have next to me. Hope you find it useful if you need it. The tolerances are pretty tight so that the buttons…
This is a set of Gridfinity Pico remote stands with embedded magnets in the bottom to help align and hold them in place in the grid. This is positioned at an angle such that you can have something taller behind (or in front) of the remote…
Replaces the faceplate of a Lutron outlet and lets you integrate two Fi dog collar chargers neatly.
I took the original design and fused the two parts together in tinkercad. This way the fan and light turn on at the same time.
This is a small holder I made for my "Chromecast with Google TV" remote, and my Lutron Pico remote. There's also another small slot in the middle for whatever you might want to put there. It has recesses on the back for Command Indoor…
Switchplate cover for a Lutron Maestro motion-activated switch. Includes a cowl over half of the motion sensor to reduce the field-of-view. I designed this because walking past my laundry room, with the door left open, would turn on the…
Remix to add a circle for extra surface area for command strips
This is a remix of my original. Some were still able to accidentally still shutoff the lights, so this is the Fix.
This is another Lutron Caseta light remote holder. The picture is the 4 x 1 meaning it holds four remotes across by one down. I modified the original remote I made (which is a 2 x 3 - two across by three down) in that I split the walls in…
Lutron Aurora Rotary Knob Mount using magnet or screws. Had one of these that the factory screw stripped or cross threaded or… so instead it uses a small screw to attach the OEM mount to the print. Space for 10mm magnets or use of two…
The Lutron Aurora comes with a bracket designed to clamp onto a traditional light switch. This helps lock the light switch in the on position to ensure smart lightbulbs are always powered on. That's all great, but when I moved, my new…
Design is in no way affiliated with or endorsed by Lutron.
Weighted base section printed out of TPU, upside down with no bottom layers to allow component to be loaded with lead shot. Vary infill density dependant on lead shot size. Base and mount require some support, but easily removed. Glue…
this is a pallet for your pico lutron switches. this will work great if you use homekit or such.
Used the no-keystone variant of the original and added a slot for a generic PoE splitter. I left the hub itself in the middle and put the splitter off to one side. It does result in close quarters for getting to nuts or screws on that…
This Light Switch Cover prevents someone from accidentally shutting off the light switch without covering the sensor. I have installed these light switches in the bathrooms (and several other rooms) of my home to help with younger…
The tolerance on the side the attaches to the pedestal is a bit too tight. I was able to get mine on with some force, but you may need to modify this to work for you. I printed upright, no supports Infill: 100% Supports: No Layer Height:…
Remix and tweak of the unit produced by eddytheflow to fit an Ikea ~51mm headboard. slightly slimmer thickness, widths; tighter fit for remote; smaller bottom access portal Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts:…
Quick and easy mount for the Lutron Dimmer Switch I used an M3x6 to attach the dimmer base to the mount, then a piece of double-sided tape between the mount and the wall
This is a friction-fit cap for the little dimmer slider on the Lutron Caseta Diva dimmable light switch. It has a knurled concavity that gives good grip against your fingertip, and makes the switch much easier to use than the stock…
An easy to mount, easy to print motion sensor cover for Lutron switches. The open area allows easy access to the dimmer switch and added support to the surrounding areas. The high hinge with pins allows for the panel to be opened wide,…
Lutron Caseta Smart Hub (formerly Smart Bridge) holder, Skadis mount. Two versions: 2 Way version with ability for cable connections to be oriented either top or bottom. 3 Way version is slightly trimmed to add the option for the cable…
This is a remix of the Lutron Pico Double Remote Stand Pedestal by justinsmonty to include 7 Pico Remotes for those of us that need a stand/Pedestal for more than 2 Remotes. This Model can also be found here…
Minimal models for mounting a Lutron Caseta Pico Remote, intended as building blocks for other projects. “Pico Remote mount” is the shape that fits into the back of the remote, like the mount included with the remote but without the screw…
If you want to mount your Pico Remote just like a standard wall switch, especially alongside a standard wall switch, this is NOT the model you're looking for. If you're putting your Pico Remote someplace else and want it to have the look…
remixed this stand model to work with Gridfinity.
Motivation I recently mounted a bunch of items to my walls and Honeycomb Storage Wall . In the process, I decided to create a template so that I did not have to keep recreating the same sketches and geometry for what is ultimately just a…
I upgraded a bunch of the dimmer switches in my house to the Lutron Caseta wireless remote switches, and I wanted a holder for all the remotes so I could control the lights from the laziness of my couch :-) I am not impressed with the…
Adds a bigger body to the light switch to act more like a remote
Replacement handle for Lutron DT-2236 tachometer case. Snaps into place, no screws needed. No supports required.
We have a dimmer switch that is now behind the mirror of our dresser. I designed this extension to enable us to control the lights without needing to squeeze our hand behind the mirror. All of the joints are print in place. Placements of…
This cover disables the motion-sensing feature of Lutron Maestro switches by physically blocking the sensor, allowing you to move around freely without triggering the switch. It attaches to the existing faceplate screw using a single 12mm…
Hole spacing fixed as seen here:
I've been running my 3D printer in an unused bathroom sometimes to reduce fume exposure. This bathroom happens to have a motion sensor switch that keeps triggering from the movement of the 3D printer. Thus this 3D printed part was…
Mount the Lutron Connect Bridge to the wall
Gridfinity Bin that holds up to 10 Lutron Pico remotes in a 1x3 configuration. No Supports Default Printer Profiles or customize as desired Variable Layer Height works well
A remix of the model where the base of the mount is covered so the magnet does not slip through. Uses 10 x 2.5mm magnet
A minimal stand to hold the Lutron Caseta Smart Hub (formerly Smart Bridge) in a vertical position on a desk or shelf. Edit: Added version with two screw holes 100mm apart. No supports needed. Print as pictured.
This is a simple model that I used to hold a lutron pico remote on a metal post in the garage. I couldn't find something else like this so I just threw something together in fusion. Worked pretty well on the first try. I used 10 mm round…
Snaps on the rectangle light switch to stop from turning switch on or off as needed. Added thin extension to fit between the cover plate and rectangular switch rim giving it more to grab and stay put.
I have this old Lutron homeworks system in my office, buttons brake with time and they don't make or sell this keypad replacements anymore. The new ones are not even compatible with my processor, so.. 3D Printing to the rescue. I tried…
I ordered a Caseta Smart Roller Shade and wanted to mount it outside the trim and above my window, but they didn't send the right hardware including screws and a spacer. I ended up sketching my own which isn't 100% perfect but works 100%…
A 3D printable replacement mounting clip for the Lutron Pico remote. This model is designed for attachment using double-sided adhesive tape (e.g., 3M Command Strips). It provides a secure, low-profile mounting solution without requiring…
A simple cover for a Lutron wall-mounted drapery bracket. The cover enhances the aesthetics of your drapery hardware by concealing the unsightly wall mounting screws on the brackets. Cover mounts vertically against wall overtop of…
Holds Lutron Caseta Pro to openGrid using openConnect. I've included full and lite connectors but you only need one. You could also use any of the other openConnect holders.
The original model was a little brittle. I found the tabs broke off.
This allows you to mount the Aurora Switch with a #8 Flat head screw to either a piece of wood or plastic Anchor
I remixed @adam Wide base stand for Lutron Pico remote to fit in with the look we were going for in our living room. If you find this useful and want to support more designs like this, feel free to toss a tip my way:…
I was surprised by the cost of a plate for the dimmer switch I just installed, so I quickly designed the part I needed and am sharing it with the world. Enjoy!
Holds a Lutron bridge in 1u. I think the screw holes will work with an m2, but I ended up just drilling it out to use an m3.
Simple battery cover, nothing less, nothing more Hole can be widen with a help of a drill if needed, model ain't perfect :) Print with latches facing the bedplate, usage of supports is strongly encouraged
Simple Lutron Pico Remote Pedestal Dock. Holds 2 Lutron Pedestals (Not included) together. This bracket holds Pico Remote Pedestals together so they don't slide away form each other. 3 Versions: 1 + 1 : Holds two (1) Pico Remote Pedestals…
I remixed @adam Wide base stand for Lutron Pico remote to a wood style. for a different look If you find this useful and want to support more designs like this, feel free to toss a tip my way: https://buymeacoffee.com/superflybass
I've been running my 3D printer in an unused bathroom sometimes to reduce fume exposure. This bathroom happens to have a motion sensor switch that keeps triggering from the movement of the 3D printer. Thus this 3D printed part was…
A simple cover for a Lutron wall-mounted drapery bracket. The cover enhances the aesthetics of your drapery hardware by concealing the unsightly wall mounting screws on the brackets. Cover mounts vertically against wall overtop of…
Snaps on the rectangle light switch to stop from turning switch on or off as needed. Added thin extension to fit between the cover plate and rectangular switch rim giving it more to grab and stay put.
Holds Lutron Caseta Pro to openGrid using openConnect. I've included full and lite connectors but you only need one. You could also use any of the other openConnect holders.
This cover disables the motion-sensing feature of Lutron Maestro switches by physically blocking the sensor, allowing you to move around freely without triggering the switch. It attaches to the existing faceplate screw using a single 12mm…
Lutron Caseta Smart Hub (formerly Smart Bridge) holder, Skadis mount. Two versions: 2 Way version with ability for cable connections to be oriented either top or bottom. 3 Way version is slightly trimmed to add the option for the cable…
This angled wall-mount bracket for your Lutron Caséta Smart Motion Sensor (PD-OSENS or PD-VSENS) allows you to set it up at an angle on a flat wall. In the second picture, you can see the original and my angled version side by side. So…
Lutron Aurora Rotary Knob Mount using magnet or screws. Had one of these that the factory screw stripped or cross threaded or… so instead it uses a small screw to attach the OEM mount to the print. Space for 10mm magnets or use of two…
I used ASA for the print because of heat from the hub, I'm sure PETG would be fine as well. You will need to print with support for the mounting bracket. Uses two (2) insert-empty.stl from the Honeycomb Storage Wall Files for mounting to…
