Liczymy pasujące modele…
Basic cover for Huawei P30 Pro. Want to send a tip? Paypal: https://paypal.me/cubikspot BTC: bc1qp7c9nllsetqf73zu76wrwxcrrks4ctpp04rnpe ETH: 0x1709A6042EAF5D36f9F4B3C3Fb4B9BC2dF9EEeaf LTC: ltc1qxwkvr2c6drmg9vdgkdcwrgk6lw4h07pnhfuxwt Print…
Bottom is flat. Case is tested. Best printed slowly in TPU.
Bottom is flat. Case is tested. Best printed slowly in TPU.
General This is a remix but I ended up re-drawing it from scratch with that model as inspiration when I realized I wanted to change several things. Mine has smaller holes to accommodate my 6" long glue sticks which are 7mm in diameter…
I have downloaded this file, and it did not fit the Siboor led lights I had purchased, Since I printed them on ABS, as it shrinks by around .5% on this long piece it was 2mm too short, so it was remixed with those tolances in mind, and…
I adapted the great parametric rugged box model to fit the tiny Miniware MHP30 hot plate because I was worried about its thin struts getting bent. This is small enough to throw into a little soldering kit. The parametric .f3d model is…
I got sick of my CPAP mask sliding up off my head every night because the headgear doesn't actually hold onto anything at the back of the head. This adjusts the angle downward so that the headgear can cradle the base of the skull and is…
FUNDA HUAWEI P30 LITE HOTEND: 225 A 235 CAMA: 50 A 60
Use 0.08-0.20mm layer height, with 2 walls, 15% infill (typical settings). Print the main mask body in a black filament to reduce reflections (though in prototyping, my green mask worked fine too). Use the multi-filament versions only if…
A mag bottom cover with a rail, for connecting anything really, but specially Mantis X sensor.
Drop in Corner Mount for Aqara FP300 Hex cutouts in the back reduce resin required by ~20%
Board models for: BME680 SHT31/SHT41 SGP30 Category: Models
I design this to mount my new phone on my gorillapod. The model has a threaded hole (1/4 inch 20 thread ) to connect it to the tripod. Print instructions No support needed
Uses the Gridfinity storage solution to hold the Brother P-touch cube label printer. Allows the printer to print while still in the box (using battery as the power port is covered). A nice height to fit into the bottom drawers of an Ikea…
Simple mounts for the Aqara FP300. I’ve included STEP files so you can easily modify them. Stand: Simple stand for flat surfaces. Clip: A clip with a 4.85mm gap which fits my cabinet door. You will likely need to adjust the STEP file to…
This is a work in progress for a P30 food truck. At present it still prints solid and rather thick though some parting has been done to avoid printing a lot of material in the interior. I still plan to create a version with thinner walls…
This attaches with a hose clamp or zip ties to the main body of the glue gun. For hinges I just used a few spare screws. Some washers at the rotation point really helps to lower friction, but the friction can be helpful. I also drilled…
This is the first working design of my Ryobi P305 Hot Glue Gun specific holster. It may work on similar models as well. The design might get a further revision to tailor it down a bit to the flared housing of the gun itself if I have…
Description A small stand for handling larger PCBs on a MINIWARE MHP30. There is a hole in the middle for a 10 x 50mm wooden stick. I printed the base and screw from PETG and the feet from TPU (FLEX) material. Additional Parts 1x wooden…
Mit dem Adapter lässt sich eine Noco NLP30 in ein Auto einbauen. Bei mir wird sie in einen Audi TT 8N 1.8t eingebaut. Meinen ersten Druck habe ich in Polymaker HT-PLA-GF gemacht. 100% Füllung sollte zu ausreichender Stabilität führen.…
This model adapts the Dyson DC14 Turbo Tool (~2006) to the Dyson Ball Animal 3 (UP30 - 2022). Snaps into place via the retention clips on the Turbo Tool and the Dyson Ball Animal 3, respectively. Use supports for recessed tube and cuff…
The MHP30 is a great tool, but having 300c just chilling on my desk always made me nervous that it might be easily knocked over when using it, or by something tugging on the USBC power cable. This 1x1 base holds the MHP30 with a single M3…
Needed a better way to store the Wireless Presentation Pod when not in use.
Simply box for DP30V5A (+ likewise models) EDIT [15.02.2019] - added back part for complete closure with ventilation holes and one big hole for connector (typically 5,5mm) Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No…
EN (en Français plus bas) You'll need two or four 20x10x5 mm magnets, depending on the desired magnetic strength. And for those who don't know where to buy them, I can only recommend https://www.123-magnet.com/cat-aimant-n-odyme-303.htm .…
I designed this stand because the Huawei P30 Pro slides off the CP60 charger easily, no matter how levelled it is. The parts are optimized for printing without support. For assembling you need: 2x M3x10 bolts Designed in FreeCAD 0.19
This is the vent cap for fuel tanks from VP. Filament: PETG Extrudr 30% filling
My rendition of a riser stand for the MHP30 miniature hot plate. This brings the top surface of the MHP30 to a height of 72.5mm, which happens to be the lowest configurable height of the Hakko C1390 Omnivise . The MHP30 can be securely…
Originally published here: Motorola One / P30 Play xt1941 case by tato_713 - Thingiverse This is the case for the Motorola One; for the One Vision visit this . Thanks to Juan Luis Maya Rangel , who help me testing this case. Some of the…
Support Post with 51mm hight. General purpose. Built for soldering large PCBs on MHP30
one of the original hooks broke and the original spacers came off, which were only glued I copied the shape of the original hook, modifying it to lengthen it with a rubber part screwed instead of glued the original hooks incorporate a…
Compatibility: Joy-it SBC-Buck03 https://joy-it.net/de/products/SBC-Buck03 Riden RD DP30V5A-L https://de.aliexpress.com/item/32639806678.html Additional (Monitor Arm) Tube Mount…
The holder for the label printer is designed for use with the Multiconnect System by @DavidD for Multiboard. The holder allows you to create labels without removing the printer. It also features a cutout on one side for the charging…
funda de TPU para el teléfono Huawei P30 lite
What is it? An adapter to allow the use of magnetic four-point headgear like from the ResMed F20, F30i, etc. on the Airfit P30i / N30i frame. Why? The back of my head is not well-shaped to retain the normal headgear for the ResMed…
this is a mockup of the Power Power Supply Modul DP50V5, DP30V5A, DP20V2A for further 3D constructions. it was not designed to be printed!
A compact grip and arca-type tripod plate for the Nikon p300 series. This adds a Ricoh GR - inspired grip, a bottom right strap connector, and arca type tripod mounting plate to the camera. Pictured here in neon green translucent…
MHP30 stand for Hakko C1390C Omnivise PCB Holder
A Gridfinity slot for Brother P-Touch Cube Label Printer
I have the cheap and very handy DP30V5A power supply, and needed a case for it. I saw some of the other cases here but I wanted a barrel jack for the input and USB and XT60 for the output, so I can connect various other types of…
Simple color ring for a MTP3000 Series radio (for example MTP3550 in the picture). The ring is exactly 0.8mm thick for a 0.4mm nozzle. It can be used single-color or multi-color based on your personal preference :) PLA works fine, but a…
A horizontal MHP30 holder that fits the gridfinity organizer. Files: MHP30-GRIDFINITY-RECESSED-TEXT - text in the middle has been recessed. MHP30-GRIDFINITY-NO-TEXT - clean look, no text in the middle MHP30-GRIDFINITY-AMS-TEXT - text as…
Mounts to attach the LDO LCP300-24D5 Power supply to a DIN Rail, in either an aligned (82mm hole spacing) or 90 degree (115mm hole spacing) orientation. Uses 4x 5mm M3 standard Voron heat-set inserts This is a remix of the Voron design…
Qi Laden Huawei P30 pro im Mercedes w204 Getränkehalter Ich wollte mein P30 pro ohne Kabel im w204 laden. Das was ich zum kaufen gefunden habe war teuer und hätte das ganze hintere Ablagefach belegt. Deshalb selber machen. Zum laden habe…
The holder is for smartphones with width = 7.3 mm and thickness = 9 mm, such as the Huawei P30 Pro. The bracket can be attached to standard connectors. The variants differ in the position of the connection surfaces. Since the Brodit…
Original Thingiverse model with pre-defined hex cutouts modified as follows: front region made solid with modifier thinned to 2mm with modifier set to no top/bottom infill with modifier infill set to grid @50% using modifier (honeycomb@…
The motorola case can be printed with ABS, PLA, PET-G and flexible material. Keeps easily access to all controls and buttons, no function will be interfered with the case on.
You need to print it in TPU. If you use the Dreamwear style headband on the Resmed nasal/pillow masks, you might have the headband slip off randomly in the middle of the night. This part prevents that from happening.
Плата преобразователя AC-DC куплена на Aliexpres, плата вторичного преобразователя DC-DC куплена там же, нужно было собрать в один корпус, Так как, надоело проектировать разборные корпуса, решил сделать одноразовый корпус, напечатал слой…
Case for the DP30V5A-L. You have to bend the current shunt wire on the board (gently, with a soft item, I used a piece of folded paper held in pliers. If you get a nick in the wire it will change the resistance. Has a side piece with XT60…
No hay mucho que decir, para cualquier aficionado a la fotografía analógica y que use una Pentax P30. Yo lo hice en ABS pero puede hacerse con cualquier material. Lo saque de un archivo STP de la cámara completa y lo adapte para su uso.…
a little box for the sgp30 co2 sensor
Recommend printing with ABS/ASA/PC or other high temp filaments. Please do not use PLA. Use support for the bolt hole. I printed with ASA and used PETG for support. Works with first and second gen GR86/86/BRZ/FRZ.
These are replacement stickvise jaws that you can use to hold a PCB at the correct height for use with the Miniware MHP30! I generated them with the official stickvise jaws OpenSCAD script, which is available here:…
It's the freeze drain outlet of a LX LP300 spa pump whith the “M” mark for the old model which is nowhere to get. It won't get produced anymore and i managed to brake my original. So i measured the orginial and tried to recreate it. Even…
Aruba Networking AP200, AP300 wall/ceiling mounting kit. This is for mounting these APs to a wall or ceiling (including angled ceilings). It uses a two (2) part mount to allow for the fitting of the mount base without having to hold onto…
I needed a mount for the Aqara FP300 Presence Sensor. I didn't like the existing ones out there; some are drop-in mounts, but since the base of the sensor has two magnets, I wanted to use them. This corner mount requires two magnets with…
DISPONIBILIZANDO ESSE ARQUIVO DEPOIS DE TESTAR VARIAS VEZES, MEDIDAS EXATAS PARA O MODELO CP300 ARTEMIS. QUALQUER DUVIDA PODE ME CHAMAR QUE AJUDO.
I was given a Extreme Networks AP305C on hands-on workshop and I wanted it to be hang on the wall, so I made a very universal (lot of mounting holes/stripes) mountplate for it.
I lost 2 of my 5 support, so I designed this replacement. Use TPU
The late 1960s/early 1970's Fujica P300 Single-8 cine film camera has a fully automatic exposure system that relies on a light dependent resistor (LDR). It has no manual override, which was a problem for the one I have that had a failed…
This is a wall mount for Ryobi P307 wireless hot glue gun.
Drive tray for IBM EXP3000 jbod based on P/N:42R4129 Printed on PLA and tested on EXP3200
A simple, not long time to print wallmount for Teclast P30 tablet. Has 4 mounting holes. Tablet fits from the top and locks.
Made an adapter for the Panasonic GH6 to put it in my JTZ DP30-Cage. Tight fit and saving money and letting me test again some construction-abilities
Problem: Airtag inside the Carbon frame did not work that well because of Mr. Faraday. There are some other good places to put one such as under the saddle or integrated inside a water bottle holder. If I were a thief though those are…
Fits the Opentrons OT-2 P300M Gen2, 8-channel pipette. Replacement for the carriage - the part that drives the plungers and tip ejector. Requires no additional hardware. Print Settings Tested using a 0.4 mm nozzle at 0.2 mm layer height.…
Secured with fan screws.
I made this part to replace the whole black plastic carriage in the pipette. I only modeled the left-most mounting screw holes. Those holes were used in the P300 Gen 2 pipette. This is the matching steel rod you'll need to build a…
Zur Montage auf dem Gerät, wenn das Anschlusskabel hinten ist. Der Rahmen passt genau in die Vertiefung oben. Ich habe zuerst den Rahmen platziert und dann die Kabelhalterung mit Superkleber auf den Rahmen geklebt. Wurde die Wallbox von…
If you have an amazon basics charger this might be for you. ‘v3’ is the original upload in pictures. ‘v4’ has a more robust outer shell (1.6mm) and encloses the MHP30 further, as well as providing a slightly deeper cord pocket overall.…
This is a replacement locking tab for the HK P30L Magazine, it may work on other HK Magazines but I've only got ones for the P30L. If it does let me know and I'll update this piece. Hope you find it useful Print Settings Rafts: No…
This is a mount that utilises the channel in the 2020 extrusion on the Z Axis of your CNC router to mount a BPV3000 air assist/mister. May fit other models of air assist. Using the awesome 3D model from Matt Davey made this SIGNIFICANTLY…
I lost one of the buttons while repairing my tiny hotplate, so I decided to print a replacement. And this is the first part that I designed in FreeCAD, coming from AutoCAD and Solid Edge, this was a learning curve but I'm glad that I did…
3D Step model of above 18650 LiIon Battery Cell
simple tactical ring with lanyard holes... designed for P30, can mount also on SRT7- SRT6 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 0.2 Infill: 100 Filament: PRUSA petg transparent red Notes:…
This is a simple push-on protective lens cap and push-on lens hood for the Fujica P300 Single-8 cine camera from the early 1970s. Printed in ABS at 0.2mm layer height on a Prusa MK4, though PLA or PETG should work fine. I painted the…
The HP P3005 LaserJet printer is an old workhorse. However, after many pages it may become necessary to replace the fuser drive gears, about a $15 fix. One of the gears is retained by a little clip HP calls the "thrust stopper." The gear…
This is a replacement locking tab for the HK P30L Magazine, it may work on other HK Magazines but I've only got ones for the P30L. If it does let me know and I'll update this piece. Hope you find it useful Print Settings Rafts: No…
Replacement for original Fujifilm Froniter SP3000 lightbox. When you want place film info film mask, and light box is missing or not working it's hard to align film to film mask. Frame is designed by me BOM: rocker switch - i used…
Wall Mount Bracket For A fsp230-aaan3 PSU that shipped with a Tiertime up 300. 2 need to be printed to mount the PSU sideways although you might only need to print one to hold it vertically. The screw holes were designed for 4x20mm…
Keep your work area neat and get rid of at least one tangled wire! Designed for the FMP30 Isoscope by Fischer Technologies, this spool wraps up your wires and holds a probe on the front side. Also, there is a small section on the 13mm…
Mio MiVue MP30 with original mount piece remains horizontally tilted level when mounted to some helmets (SHARK GT EVO, LS2 FF906 ADVANT etc.). This tilt cannot be reduced by original mount plate. This additional mountpiece eliminates this…
Mounting bracket to put the LDO LCP300-24D5 PSU on the back of Rolohaun's Rook MK2 DIY 3d printer. I took design concepts from Kanrog's litany of existing mounts. I did use heat sets on this because of the weight of the PSU. Items needed:…
Kryt tlačítka prodlužovacího kabelu TAPO P300, které stíní jeho světelný smog
We needed a toilet cistern spare parts for a Geberit UP100. You can only buy the whole valve and not the little lever from it. I printed it with PETG-CF in 0.2mm layerheight. Have fun with it!
Is a phone case for Huawei p30 lite with the name Antonio.
Customized back panel to a a BTT SKR3EZ and LDO LCP300-24D5 PSU on the back of Rolohaun's Rook MK2 DIY 3d printer. The original panel is designed to have mounting brackets hot glued on but after making brackets for these devices I was…
This project includes a 3D-printable adapters that allow ResMed F30i/X30i headgear to be used with ResMed N30i/P30i masks . BOM: F30i/X30i Replacement Headgear compatible with ResMed CPAP masks Original attachment pieces from an X30i mask…
probably u should print at 98-97% depend on which material u use and your flashligt measurement (50 mm +-) i use petg+ and had a nice fit at 97% on P30 and a 98% on other 50mm head diameter flashlight. infll 20% Category: Sport & Outdoors
If you lose your Mio MP30 GPS camera's SD card slot cover (or USB port cover, which is the same), the only official way how to solve this problem is to buy a new camera, as this small part is not sold separately. Or - to print yourself a…
Die Kappe kann liegend gedruckt werden und benötigt keine Stützen, bei dem Übergang werden Stützen benötigt. Ich habe es mit PETG und 15% Infill gedruckt, das reicht völlig.
Low profile handles for Iceco JP30 fridge (non-wheeled version). I designed these to replace the original grab handles since I needed the fridge to fit in a very tight space. I created the original sketch, and used AI polish the model…
The holder is for smartphones with width = 7.3 mm and thickness = 9 mm, such as the Huawei P30 Pro. The bracket can be attached to standard connectors. The variants differ in the position of the connection surfaces. Since the Brodit…
Drop in Corner Mount for Aqara FP300 Hex cutouts in the back reduce resin required by ~20%
This is a work in progress for a P30 food truck. At present it still prints solid and rather thick though some parting has been done to avoid printing a lot of material in the interior. I still plan to create a version with thinner walls…
Is a phone case for Huawei p30 lite with the logo of Scuffers.
