Liczymy pasujące modele…
Requires: One 42mm diameter pine dowel(length to preference). Two 3D printed wall brackets. Two 3D printed pole endcaps. Six 10g 45mm, self-embedding timber screws. Installation: Brackets: Pre-drill timber screws through PLA slowly to…
Wydruk około 10,32 €–12,61 € nettoWstępna wycena jednego wariantu
This Govee Pro outdoor LED light (HERE) mount is friction fit around the top of the LED but remains loose around the bottom. This allows the mount to be placed over the strand (and not fall off) while attaching outside. The design is…
DO A TEST PRINT BEFORE PRINTING A BUNCH This was made because some soffits have part of the rafters sticking out below them which makes it difficult to property align the lights. A solution is to buy long thin pieces of wood…
These mounts are for the newer E22 lights from Eufy, not the older E120. Ensure you have the correct lights. An easy way to tell is the E120 lights don't have any place to add a screw and only have 3M adhesive backing, the E22 lights have…
9/23/2024 UPDATE: Tested Successfully Have connected and tested now, these are working great! If using KUSBA or other USB connected accelerometers, I found that an easy way to get connected in klipper is to use /dev/serial/by-path/xxxxx…
Print: PETG 100% infill for a more sturdy outdoor reliable hook. Install: Slightly unscrew gutter screws on both side of where you want to insert hook. Use plastic spudger (wedge) to slightly bring gutter out from fascia. While gutter is…
I had cables of different diameters coming out of an electronics box that needed securing and this is the simplest solution I could think of. You can easily customize it to fit your needs. The Fusion 360 model is parametrized: each cable…
Simple permanent padlock with a height of only 30mm. Once locked, it can only be reopened by destroying the lock. Preferred material for printing is PETG, but PLA works too. Simple assembly. Superglue can be used to make a padlock much…
This mount for the Goobay Bike-Power 5.0 power bank allows for a permanent installation of the power bank to any 42 mm headtube of a bicycle. Requires additionally: 4x - M4x8 Hex Screws 4x - M4 flat Nuts 2x - M3x16 Screws 2x - M3 Nuts The…
UPDATE: 2/9/26 Updated the design to have better heated insert support. New single bolt version. UPDATE: 7/27/25 Updated the model to support the use of a single M5 bolt now and better (not perfect) heated inserts. Enjoy!…
This is a small shelf to hold a permanent marker like a Sharpie. I use it on my kitchen table so I always have a Sharpie close at hand while I cook.
I made these to cover the Govee lights to paint them. Initially I also designed the track but realized it would be a huge waste of time to 3D print the track myself when there are plenty of cheaper options online. The ones I am using are…
A permanently locking wall plate for a light switch. This prevents the switch from being able to be turned on or off, depending on the orientation of installation. This was originally designed to prevent smart devices such as smart light…
Simple permanent padlock with a height of only 30mm. Once locked, it can only be reopened by destroying the lock. Preferred material for printing is PETG, but PLA works too. Simple assembly. Superglue can be used to make a padlock much…
Finally, a proper home for your permanent markers, because apparently letting 30 colors roll around in a drawer like feral art supplies is “organization” now. This 3D-printable angled marker rack is designed to hold 30 permanent markers…
Bracket for Eufy outdoor lights, remixed to add screw holes. Holes are intended for #6 wood screws. Prints fine without supports for me. See…
Did you install the Govee Permanent Outdoor lights only to discover that you're being blinded through your window? Well, here's the fix for that. This model can completely black out individual lights, or work as a diffuser. It all depends…
I ordered these track lights from Aliexpress as a kit, sadly they didn't come with endcaps so I designed some up. One is just for closing off the end, the other has a hole for wiring. This is the kit I ordered:…
Had some left over eufy outdoor light strips - didn't want to use the adhesive for the ceiling, so I made a clip to snap to the drop ceiling rails. Edit-slight update to add fillets that were missed.
Wife wanted the Govee Permanent Holiday Lights to look like old school C9 bulb strings, so I added a C9 holiday light bulb shaped diffuser to the mounting bracket, positioned so it gets fully illuminated by the bulb but does not disrupt…
Print with the top of the cap on the build plate without support, maybe a Brim is required.
Remixed Banzaito's model to have holes for an igus cable chain as they are often included in Ender 3 to Switchwire kits.
Brackets for Govee H706C Permanent Outdoor Lights Pro Remix of https://www.printables.com/@Gelap https://www.printables.com/model/630613-govee-permanent-outdoor-lights-pro-mounting-bracke
This is a bracket to be able to mount a light at the top center of a roof gable. It doesn't matter the pitch of your roof. You need to print 2 of the “gable mount 2” file. Outside of that it is pretty straight forward. I used #8 1/2"…
This is a remix of the original side drainer provided by HeyGears. With the original model, you'll have to use two M4x12 screws in order to secure it to the build plate. There are also other solutions out there to hang the buildplate at…
Slight modification to the narrow mount introduced by Gelap with removal of two of the corners so there are only two mounting holes. Added two alternative versions for mounting the junction between light strings. One with just a single…
Got tired of trying to keep the hose off the floor and at hand when I'm working on a project. This lets me keep the hose handy as long as there is a horizontal surface to which I can attach the clamp. The clamp mount versions fit the…
Gelap has made a great assortment of mounts for the Govee Permanent Outdoor Lights Pro kit. After installing them, I found a need for a few extra accessories to clean up my install. // UPDATE DEC 2025 Added my 4" x 8" approx. S Curve that…
Govee Permanent Outdoor Lights Pro 2 Mounts If your home is like mine, your soffits require a bridge at specific intervals. This model creates a secure bridge mount with the security benefit of hiding screws behind the cap with a snap…
Govee H706A Permanent Outdoor Lights Pro Mount Bracket I’ve designed two versions of this mount: A side-mount version A narrow-edge version requires just 1.5 inches of space. Both versions are designed with #8 self-tapping screws. I…
UPDATE: 2/9/26 Updated the design to have better heated insert support. New single bolt version. UPDATE: 7/27/25 Updated the model to support the use of a single M5 bolt now and better (not perfect) heated inserts. Enjoy!…
zum Verbleib an oft benutzten Sechskant- Schrauben. Gedruckt mit verstärkten Wänden und 25% Infill.
This a solid end cap that fits the permanent trim on our website. Print: Printed with the solid flat face down. Printer: Prusa i3 MK3S+ Resolution: 0.25mm Infill: 35%, Gyroid Perimeters: 4 Layers: Top (4), Bottom (4) Supports: No…
This a middle joint that fits the permanent trim on our website. This is the clip version that is installed after the trim is up. It slides onto the outside of the trim and wedges in where the top and bottom trim pieces meet. This wedge…
This a middle joint that fits the permanent trim on our website. This is the half sleeve version that is installed while the trim is being installed. The ends of the trim slide into the clip and there's a positive stop (wall) in the…
A middle joint that fits the permanent trim on our website. This is the full sleeve version that is installed while the trim is being installed. It slides over one end of the trim, the 2 pieces of trim are butted together and secured,…
Summary Designed to fit over the Z-stepper mounting bolts in the base of the print chamber (see photo). The model is a single piece. Print two of them. Discussion When doing a platform calibration, the printer will bring the print bed to…
Glass marker. Possible own sign with permanent pen. Write do you want on it!!
NOTE: The model was designed for my 3D printer tolerances. If things do not fit or are too loose, you may need to adjust the dimensions. I also recommend high quality print settings for the cap insert, as the sharp edges will fray the…
Many Liturgical Books have Leather Tabs for easy turning during services. Sometimes, those tabs wear out, or they are just not there (or not in the right place). Now you can make your own tabs and place them consistently. There are three…
Requires a decently well calibrated printer. I apply a bit of cyanoacrylate accelerator to the white bit on the inside of the syringe then pretty much put a healthy amount of superglue onto the center peg of the printed plunger. I printed…
Inspired by the 500 cigarette adapter, this device allows you to sniff an entire box of 36 Office Depot Permanent Markers. The markers are held in a 6x6 grid, spaced at 15mm. The holes are tapered to match the shape of the markers to hold…
My mom likes to have the names of her plants in the pots because she has A LOT of plants and varieties. She used to make new popsicle sticks with the names of her plants every 3 months or so because they would fade in the sun, get dirty,…
I designed and printed this adapter to put on my printer enclosure wall to vent fumes out of the nearby window when printing ABS/ASA. This adapter was designed to utilize a portable AC window kit that used a 5.1" exhaust hose (search for…
This is a small shelf to hold a permanent marker like a Sharpie. I use it on my kitchen table so I always have a Sharpie close at hand while I cook.
Followed https://www.reddit.com/r/rokid_official/comments/14ksyh8/hardware_way_to_alter_ipd_distance_between_pupils/ but it frustrated the heck out of me trying to hold the prism. And getting more permanent solution, was so unnecesserily…
Very simple screw in base for electromagnetic air pump. This pump would slightly move, over time, created this to contain it next to my laser cutterr. Feel free to tinker:…
This is a permanent parametric(ish) for attaching the prusalock semi-permanently to doors without locks. The model is parametric and can downloaded and modified on OnShape here using the Variable Table.
You will need a piece of standard 3M VHB tape. This tape is typically about 1mm thick. Simply stick the tape to the bottom of the finished print, and cut out the hole. Then check that your included MCX-to-BNC connector fits snugly into…
Elegoo Saturn Ultra 4 Buildplate holder permanently installed (prt- and stl-file)
Permanent drip holder for Photon Mono 2, stays on during printing. Step file included for modification for other models.
Dm me for any questions or to request a part for me to make, thank you.
Angled bracket for the Asahom S108 Permanent Christmas lights. Lights slide into this mount and fit snuggle so that they don't fall out. It is at a 30 degree angle, great is you are installing on the Fascia facing back to the house.
I have recently purchased a set of Govee Permanent Outdoor Elite lights. I did not like the idea of seeing exposed wires under my gutters. I saw that someone has made a cable runner channel with a clip-on govee light cover to make it seem…
For some strange reason the controller does not have any mounting tabs, so I guess it's meant to just flop around on its cables. Hum… I printed in PETG with the top/outside face down and supports under the tabs. Fusion 360 model included.…
Use this to mount any smartphone or even tablet anywhere. Using zipties makes it deliberately inconvenient for thieves to just take it from there. The "side" pieces are to be printed from solid materials and the middle part is to be…
This is a library of small part organizer drawer replacements that have permanent dividers to create multiple bins in one drawer. The many available removable divider systems for this are great, but when working with tiny parts (e.g. M2…
I made these to cover the Govee lights to paint them. Initially I also designed the track but realized it would be a huge waste of time to 3D print the track myself when there are plenty of cheaper options online. The ones I am using are…
Circuito Permanente de Jerez, Jerez de la Frontera, Spain, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate…
Remix of 2cm (3/4") male side of snap buckle for permanent attachment. I printed it with 5 walls and 35% infill.
A permanently locking wall plate for a light switch. This prevents the switch from being able to be turned on or off, depending on the orientation of installation. This was originally designed to prevent smart devices such as smart light…
They say that I'm a mean one. I don't like giving people gift cards - they're too impersonal. We've got a couple of 19-20 year old relatives though for whom we have no idea what to purchase. They're getting gift cards. But this year, they…
Finally, a proper home for your permanent markers, because apparently letting 30 colors roll around in a drawer like feral art supplies is “organization” now. This 3D-printable angled marker rack is designed to hold 30 permanent markers…
We all know the problem. Standing in the bathtub shower with the shower curtain trying to hug you while you are busy cleaning yourself. This is no more. Print out these bad boys, snap them onto the shower curtain and they will now neatly…
Designed this to bolt on to an RV roof rack to be permanent. the stock mount would easily come off and not good for driving. Not restricted to RV use only. The mount does not block the view angle of the camera. I added a small cutout on…
Crimson Permanent Assurance 1872 from the featurette - The meaning of life Please support me by following me
This support is permanent and therefore always ready to receive the tray. Very convenient when you already have a busy hand. Printing: PLA, no support, 100% cooling, no special precautions. Place it 5cm from the front. Print Settings…
I hated having to reach down to the floor to grab my phone charger's cable every night. This keeps it handy at the top of my nightstand. This is meant to be semi-permanent, once the dovetail slides together the interference between layer…
Made for the Miele W4802 model, but should work for other similar models. After confirming it works, I recommend using a small amount of glue to make it permanent.
Levitating a magnet above another permanent magnet is impossible! It doesn't matter how many permanent magnets you add to the system, it won't work! To make it work, you need one of two things: 1. Make the magnet above spin (but it will…
Permanent Orienteering Course Control Point Marker Flag Setting up some permanent orienteering courses (POC) with ~3.25 x 3.25 in. (83x83mm) control marks (tiles) for placing on 4x4 posts, etc. Included are a variety of 3 letter tiles…
I created this model to replace the power socket on an Oase InScenio 230 with a permanent connection instead of an extension cord. Main reason was, that I have several of these in serial, all connected to a 5x2.5mm² line and I wanted to…
The Pen Pear Pal is an ergonomic fixture that goes on a sharpie to increase usablility for people with a number of difficulties holding pens, such as arthritis, tremors, or fine motor disabilities by increasing the size and weight of the…
Need M5 nut and screw (or you can use screw that came with camera accessories) Update to Permanent Go Pro mount https://www.thingiverse.com/thing:2229731 Category: Camera
Need M5 screw and nut Build video: https://youtu.be/joOGsJAsfJ0 Category: Camera
Description: Sometimes the chase for a mosquito or a fly takes longer as expected. Constantly keeping the finger on the button is exhausting, so there had a solution to be found. This gadget allows you to keep your Insekten Schröter or…
I installed two battery monitors in my camper van (one to monitor everything going into the battery, and one to monitor everthing going out of the battery) The unit was bougth from ebay (search for: "4 in 1 DC LCD Voltage Current Battery…
Here's a remixed version of the weather station enclosure for wall mounting. It's designed to use a DC threaded jack ( https://www.adafruit.com/product/610 ) for wiring a 5v supply to the USB power line so that your weather station can…
There are two parts of the Sharpie holder, which 20_Sharpie_holder is a base and 20_Sharpie_holder_pad is just a decoration - it is not necessary to print. Hole diameter = 13 mm / 0.51 in No supports No glue 15% Lightning infill is…
This is a screen cover for the ender 3/Pro. I recently got a Beaglecam and the glare from the screen looked a bit rough on the night vison time lapses. This cover is designed to snap into place to cover the screen. It is loose enough to…
These couplers keep your Huckleberry Lighting permanent holiday lighting tracks aligned during installation and keep the ends of tracks aligned after installation. They snap into the track and have very small little nubs to keep…
Picked up a set of the Govee RGBIC permanent outdoor lights but I'm not a big fan of the idea of using the adhesive. Partially because I don't want any residue to clean up in the future should these lights fail or loose their appeal and…
The Extrubox, a high quality printer enclosure customizable in size and removable within seconds from your printer when you want to work on it, when you want to use it for several printers or when you just don't need it right now! This…
I haven't tested this model yet, so any feedback is appreciated. Designed for 13mm (½ inch) marbles or bearings. Support contact distance is set to 0 for permanent attachment.
This spoolholder fits most common 1 kg spools. It is supposed to be glued on top of the Prusa Lack enclosure.
I made this for attaching my ring light or camera on ceiling / wall. Quick release and tested with Manfrotto plate. Video of this thing: Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Category: Camera
3D Modeling noob trying new things. Permanently mountable solution with standard wood screws to a desk or wall. Perfect for office, workshop, home, etc. Simple model that I wanted to be compact and rigid. This model (using a standard PLA)…
3D printed clips to attach WS2811 Pixels in J-Channel to the soffit for Permanent LED Lighting. Printing: Clips: PETG or ASA - .3mm at 20% infill Drill Guide: PLA - .3mm 20% infill stand on end (will fit on Prusa MK3s size printer) Clip…
I've designed a mounting plate for the Creality Ender 3 S1 to accommodate its Laser Module . In my case it is the 10W version, but the lower ones should work as well. The key advantage of this mount is that it provides more vertical space…
Permanent Quick Release plate for ARTCISE FH6 video head modified to use M6x20 for mounting Analog Sky Magic. Use double sided tape (or cloth tape) to increase friction between the QR plate and binoculars so it don't spin. Link to video…
Einfach mit Std. Einstellungen für PLA drucken. Es sind 2 verschiedene Modelle für große (IKEA) Teelichter & ein Adapter um auch kleine Teelichter nutzen zu können. Wir haben die Drucke seit mehreren Jahren im Einsatz und es gibt kein…
Made for Govee permanent outdoor LEDs. Using this the keep the lights aiming perfectly vertically straight when mounting along the sloped are of the roof line.
This is a set of parts I made to re-enforce the 3M adhesive used to mount Govee Permanent Outdoor Lights Pro (H706A). Light Mount : A small frame that goes around the outside of a light that can be screwed to the mounting surface to…
This is a complete redesign of my https://www.thingiverse.com/thing:3204558 gutter Christmas lights. The problem with the gutter lights is they only last 1 maybe 2 seasons. This new version is a thick screw in kind. Super easy to print.…
Fits perfectly when printed on my printer, you might need to adjust it slightly bigger or smaller. I will be installing these with outdoor 3M Command Strips so I didn't need holes but adding them in the slicer is pretty easy. I've…
Bracket for Eufy outdoor lights, remixed to add screw holes. Holes are intended for #6 wood screws. Prints fine without supports for me. See…
I made this spacer tool to help install the excellent snap in Govee light holders from: https://www.printables.com/model/593227-govee-rgbic-led-permanent-outdoor-lighting-mountin This allows me to space them 8cm from the house, which is…
What This remix adds a mount for an ADXL345 accelerometer to the permanent BL-touch mount. If you already have a permanent mount and cabling for a BL-Touch, might as well throw in an ADXL345! Requirements 1x base abl_plate from the…
Govee tape fail? Here is a simple bracket to hold the lights up. Low profile as possible to not grab attention, and doesn't go over the lense and take away from lighting effects. .2mm layer hight with a .6mm nozzle no infill Any filament…
