299 models
This is a full set of all small letters of the alphabet. It is a two-colour PLA print with embedded magnets. You need enough 4x5 mm cylindric neodymium magnets to embed into this print. These can be bought cheap in large quantities. The…
Print approx. €7.18–€8.77 excl. taxPreliminary estimate for one variant
Fast and simple magnet holder for sticking stuff on magnetic surface. I have 10 x 2 mm magnets laying arround and a doughter that was struggeling to pick up and place magnets on wall board - so I made this - quick and dirty :) Magnet is…
Print approx. €0.09–€0.11 excl. taxPreliminary estimate for one variant
Core One Purge Bin with Nozzle Wiper Clearance Remix - 6x2MM Embedded Magnets. No glue needed due to layer pause.
Print approx. €2.39–€2.92 excl. taxPreliminary estimate for one variant
This is a remix of the Modular Trailer Hitch Cover by rkxone on Thingiverse. I've added an additional set of faceplate mounting holes for more options when designing faceplates. The m3 nuts are also embedded in the print. Stop the print…
Print approx. €4.69–€5.73 excl. taxPreliminary estimate for one variant
Another iteration on already stellar designs, just some small tweaks to embed the 6x2mm round magnets into the print with a pause at layer 17 to place the magnets when printing.
Print approx. €2.96–€3.61 excl. taxPreliminary estimate for one variant
This is a recreation of the Top Gear Lap Times letters using the Nuber Black font with embedded 5x10mm neodymium magnets. I've also included a dry erase marker holder (diameter of marker <19mm). The letters use 22 magnets while the marker…
Print approx. €2.48–€3.03 excl. taxPreliminary estimate for one variant
Remixed waste bin with enclosed magnets. NOTICE: This is just a crude modification.
Print approx. €3.02–€3.69 excl. taxPreliminary estimate for PETGSource material: PET
In the slicer a pause can be added to the print: Choose the first layer covers the internal hole for the key by using the layer bar in the right side of the slicer screen. right click on the orange plus and choose “ Add Pause Print (M601)…
Print approx. €1.21–€1.48 excl. taxPreliminary estimate for PETGSource material: PET
Using the same 5x5mm magnets as the original, but I wanted the magnets embedded into the print just to make sure they never accidentally fall out. The magnets have a slightly looser fit than the original so they should easily slip into…
Print approx. €4.93–€6.02 excl. taxPreliminary estimate for PETGSource material: PET
Remix of PLA Filament Box with embedded lettering for PLA, and other types of filaments. Changed the font and lettering so that the wording is flush with the box top. Filament for Dual, Tri, Galaxy Box Top: Prusa Galaxy Green PLA with…
Print approx. €3.54–€4.33 excl. taxPreliminary estimate for one variant
There is a version without embedded magnet spots and one with. (!) If you want to embed magnets, make sure you look up how to add a pause during the slicing process. This varies by slicer. (!) The current design is for cylindrical…
Christmas tree with embedded addressable LEDs using color change feature of PrusaSlicer. 3D print is divided in 4 stages with in total 25 LEDs. Using a Trinket M0 Arduino compatible board and a Li-ion battery to drive the LEDs and…
This 3D-printed case, slightly inspired by the Amazon Echo Show, is designed to integrate a Raspberry Pi with a 7-inch display ( link ), offering a compact and clean solution for various projects. The Raspberry Pi is mounted on the back…
Used Poly.cam to scan Crystal Embedded Halloween Themed Skull. Thought it came out really well and wanted to share it. Etsy Page: https://demambaprints.etsy.com Tik Tok: https://www.tiktok.com/@demambaprints Polycam scans here:…
Use the Ball Buddy to customize your golf ball. For SLA or FDM single filament printers this model has two versions of the magnetic golf ball stencil holder (exposed and covered magnets). Both versions made up of two ball holder halves…
I have modified the model to hide the magnets. It looks much better. But it is VERY IMPORTANT! You'll have to set the slicer to STOP THE PRINT at the top of magnets, before the first layer, that covers the magnets. Here is a tutorial…
PS4 Game holder for up to 10 games. Print upright with the text on the the print plate. It is a 30 degree overhang so you don’t need supports If you use the stl, simply color the logo in the desired color with the paint bucket no supports…
This is a simple dice with a skull-shaped void inside it. In order to see the skull you need to use a transparent print process. Theoretically SLA should work (but lacking an SLA printer I haven't tried). For FFF Colorfabb HT will work,…
Note: This was remixed from a model on Thingiverse and is now imported here. I saw on my Ender 3 V2 that I had screw holes that was intended for Creality's new BLTouch kit. I really like the mounts from prydonian and puturai, but both…
PS5 Game holder for up to 10 games. Print upright with the text on the the print plate. It is a 30 degree overhang so you don’t need supports If you use the stl, simply color the logo in the desired color with the paint bucket no supports…
Here is a version of my WiFi QR Code Sign that uses embedded 8 mm x 3 mm magnets ( Amazon ) instead of a stand, so you can attach it to your refrigerator or any other ferrous metal surface. Use this sign to share your WiFi hotspot SSID…
These base plates have the magnets (6x2mm) fully embedded into them, no more using glue! Perfect for a metal working shop, or anywhere with metal dust that could possibly stick to the magnets, much easier to keep clean. No need to worry…
By increasing the thickness of the shell, it was possible to place external antennas and leave room for other modules in the future. Main features: free space in the shell for other modules; fastening only with magnets (8x2 mm); holes for…
This script will allow you to use the Command Line on your computer + OpenScad to generate HUGE amounts of any OpenScad file (Labels, Personalized Designs, etc) using a simple CSV. How To Use It: Populate the CSV File with everything you…
These emoji tokens use special gcode and dont use much filament. Enjoy. A single extruder is used to make an embedded, multi-color design that exists only on one layer of filament. Update: turns out I didn't merge the kiss emoji…
PS3 Game holder for up to 10 games. Print upright with the text on the the print plate. It is a 30 degree overhang so you don’t need supports If you use the stl, simply color the logo in the desired color with the paint bucket no supports…
The ball Buddy pro model requires a multi-filament printer for the living flex hinge. A fun ball marking tool that allows for interchangeable stencils. Consists of two ball holder halves connected with a flex hinge (requires a flex…
TPU case for the LilyGO T Embed & T Embed CC1101 since I couldn't find one! I suggest using TPU 95A or softer for the case if you have antennas/SMA connectors, since they do take some effort to put on. Otherwise, there shouldn't be too…
12 most common magnet size holes (flush and embedded) provided in Files. These voids are created by an OpenSCAD script that will create cylindrical holes to be used in creating a negative space in your model that fits a cylindrical magnet…
I found the knob to slippery so made a simple grip ring.
EDIT 12/11/2024 Numbers were added. Features This printable is designed as a manual multi-color print. Orientation of the models are face side down. Borders Letters have a border to make them visibly pop. The border and the model need to…
Wanted to build an embedded wall panel for controlling Home Assistant in the house, so created a 3d printed design to perfectly house the tablet. It has small holes for 4mm magnets to allow the cover to be easily removed, so just need to…
A two piece, glue together model of the Detroit Tigers “D” logo. The Inner piece features three slots for embedding magnets inside the print if desired. (2) magnet holes: 23.5mm x 5.5mm high (1) magnet hole: 19mm x 5.5mm high Can also be…
Update: Febuary 10th 2022, added a setting to print the original case and stl without the Raspberry Pi cut-out. Because of power issues when using power from the MK3 board, I have changed to an external case hooked to the frame just below…
A LilyGo T-Embed CC1101 Body with dual SMA antenna holes. This is the stock body part and is not optimised for FDM., so it will require well-tuned support setting.
The original author removed the keychain holder, so I made a Parametric Keychain generator, for the model.
This paw print has an internal space to embed a magnet while printing. It's a practical decoration that's inherently safer than many magnets you can purchase, since this one won't ever fall out. Design features The model is large enough…
Nintendo switch game holder, for up to 12 games, with embedded nintendo switch logo eliminating the need of glue. Print upright with the text on the the print plate. It is a 30 degree overhang so you don’t need supports If you use the…
Work in progress version. Needs a few tweaks here and there, STEP files are included if you want to make changes. Hardware: M2.5x16 screws (ISO4762/DIN912) - 4pcs M2.5 heat set inserts, 5 or 6mm long - 4pcs M2.5x5mm flat head screws for…
LilyGo T-Embed CC1101 is a cheap alternative for flipper zero,but there is one small issue:there is no power switch for device.Even works in deep sleep mode,the battery drained in two days. So I modified the official shell to add a power…
This model takes a small 8mm ball. The model can easily be scaled for different ball sizes but would need to be split and printed in pieces for smaller printers. Supports are required.
Remixed Itty Bitty Fidget from @3DPrinty: https://www.printables.com/model/205599-itty-bitty-fidget Printed with 0.1mm layer height, using a pause to insert the magnets before the holes are covered up.
1 version - with magnets 6x3 2 version - with screws, but without a hole for the switch 3 version - without magnets By increasing the thickness of the shell, it was possible to place external antennas and leave room for other modules in…
I have installed an NRF24 module in my Lilygo T-Embed, so I created a back cover to accommodate two external antennas for 2.4GHz and 433MHz. Also it can be used if you like to install two external antennas to improve signal coverage. It…
3/8" SAE Standard socket organizer with embedded magnets and debossed ID sizes. Sizes include - 5/16", 3/8", 7/16", ½", 9/19", 5/8", 11/16", ¾", 13/18", and 7/8". Uses 15mm x 2mm neodymium magnets from amazon
I've also included a gcode file for a Prusa Mini/Mini+ which has a Pause At Height for letting you put in the magnet. Note : The pause occurs approximately 21 minutes into the print. CAUTION : I'm not sure if it's an issue with the Prusa…
This design is easy to remix as sufficient tolerances are there to add or remove material without breaking the design. Dimensions for the pocket for the embedded magnets : 6.2 mm x 12.8 mm x 12.8 mm Printing: You will need to configure…
the new file has an integrated screw to fit the lamp top as shown includes cap files for the regular sized moon and a smaller moon printed at 85% scale from this link:…
Magnet sizes are 8x3, 10x3, 12x3 ( also added one 15x5, so its more “universal” but its not tested yet ) To insert the magnets, print with a 0.15 layerheight then set "change filament" >>>layer 25<<< ( 3.80mm ) For the 15x5 at >>>layer…
Double-breasted dovetail joint partially embedded, teaching aid for joiner and carpentry in secondary schools. Oboustrabbý rybinový svlak částečně zapuštěný, výuková pomůcka pro obory truhlář a tesař středních škol.
1/350 Military Model German Embed Light Cruise full hull model, if you want to print this model, I recommend to print on
I really like the original model but wanted the magnets to be embedded. Pause the print before the cavities get covered and insert two 3x2 mm magnets. The fit is quite tight which also prevents the magnets from sticking to the magnetic…
Embedded microfluidic mixer Shafique, H. et al. High-resolution low-cost LCD 3D printing for microfluidics and organ-on-a-chip devices. Lab on a Chip (2024). https://doi.org/10.1039/D3LC01125A Category: Engineering
This is a fake-bolt geocache , with room for a magnet to be embedded! The printer will seal the magnet in place. Four sizes are included, and six magnet sizes as well. All magnets are listed as [diameter] x [thickness]. Some sizes require…
When I found this remix of “High Tech Pet - Automatic Dog Door Collar Tag : 1in (25mm) Collar Mount”. I was like, this is just what I'm looking for since the strap mount for the device is what I consider small for our dogs. The designer…
Originally designed to be embossed with lettering, after printing i discovered that the lettering was suspended withing the key. This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/hCUeiDwCc7Y Print…
I didn't want the closing mechanism to be at the bottom, because the door stop would need to be at the bottom as well, which can be an obstacle. That's why I put it all to the top. Also the smaller hinges/handles seemed a bit week, which…
here is a cover for LilyGo T-Embed CC1101 that you can choose yourself what color it should be instead of the standard cover that comes with it when you buy it This also saves you from having to destroy the original antenna to retrofit…
This is a set of Gridfinity battery trays with embedded magnets in the bottom to help align and hold them in place in the grid. Importantly, this set keeps the batteries all at the same height across the different battery heights, making…
Little Ladder This is a slightly larger little ladder created to attach to cars or a fridge. Embedded magnets help avoid the magnets from scratching paint. No text is printed on the ladder so you can customize it anyway you would like.…
Intro Turn ordinary metric screws into strong, ready-to-use handles with this simple 3D printing technique. These knobs are designed to be printed directly around a hex-head metric screw. The screw shaft protrudes, while the head is fully…
Needed a small funnel to fill a decorative oil lamp. Designed it to embed a rubber band for hanging on the refill bottle. Be careful with your choice of print material, making sure it withstands the liquid you will use it for. Print with…
This is a WiFi logo that you can embed a NFC round tag into. The tag I used was a NFC 215 with a diameter of 25mm and 0.91mm depth. You will need to stop the print twice with a color change or filament run out, at the appropriate layer,…
Modified LACK enclosure for Prusa MK3 with an embedded thermometer and LED dimmer. This remix modifies the top corner pieces so that a thermometer can be put inside the left leg piece and a LED dimmer inside the right leg piece. Warning:…
I didn't like the look of printing text on my filament swatches and I have poor handwriting, so I decided to embed NFC chips inside them that contain filament information. This also allows for more characters, links, images, etc. It fits…
Remixed several times. Great design. If you need different sizes, you can adapt the solid-works (2025) file easily… or ask me in case you don't have Solid-Works :-) Assembly → Self explanatory Brillenetui_Innen.SLDPRT → help file to…
I designed this to make the task of getting nuts ready to embed into my 3D prints easier and quicker. I was tired of going to my big tub of fasteners to get a small number of nuts while I was printing. Generally I use M2.5, M3, M4, or M5…
REQUIRES: 2pcs x Printed Model 14pcs x 6mm Diameter, 2mm Height Cylinder Magnets Remember to pause at the right layer to embed the magnets, mind the polarity too. Model features a divot to fit the index finger and thumb for a better grip.…
Update: Febuary 10th 2022, added a setting and stl to print the original case without the Raspberry Pi cut-out. Because of power issues when using power from the MK3 board, I have changed to an external case hooked to the frame just below…
This is a basic sliding dishwasher sign to show whether your dishes are dirty or clean, just flip the sign when you start the dishwasher and whoever walks by next will know your dishes are clean! This uses a snap-on slider, and uses…
I printed everything with .15mm layers so the top of the magnet is covered by 4 layers instead of 3
You'll need 3x - 8mmx3mm neodymium magnets. If printing at .2mm layer height, pause at layer 18 to install the magnets. Here's the ones I used: Amazon.com: FINDMAG 50 Pcs Fridge Magnets, Small Magnets, 8x3mm Neodymium Magnets,…
This 3D printed dog tag is made of durable PLA plastic and features an embedded NFC chip. The chip can be programmed with your dog's name, contact information, and medical information. This makes it a great way to keep your dog safe and…
This is a remix of the WiFi QR Code Sign - Embedded Magnet Version that uses embedded 8 mm x 3 mm magnets ( Amazon ) and has a recess for a 25mm NFC sticker ( Amazon ). Use this sign to share your Wi-Fi SSID and password with your guests.…
крыша tembed Магниты 8Х2 ММ Добавил пару отверстий для выключателя по запросам, если что то не совпадает пишите в коменты Я не тестил крышку с выключателем Если вам не подходит сторона выключателя B просто отзеркальте модель , она…
Remake that adds a speaker and a Web server. Animations and music are controlled via an Internet browser. Print instructions Details of build at https://www.hackster.io/john-bradnam/embedded-neopixel-led-christmas-tree-58d676
Nintendo Switch game holder with embedded logo and pipe Print upright with the text on the the print plate. It is a 30 degree overhang so you don’t need supports If you use the stl, simply color the logo in the desired color with the…
This has slots for 2x6 magnets in each of the four corners. Just add a “Pause Print" at the appropriate spot, and place them in!
A guitar pick (Fender 351 style) roughly 31 mm long × 26 mm wide × 1.2 mm thick. KISS logo embed in. You can adjust the thickness (z-size) but notice the logo depht. Rock on!
This is a small magnetic shelf I made to hold my tea boxes on the side of my fridge. It's wide and deep-enough for a 9cm x 11cm tin tea box, but can also be used as a spice rack. It's designed for use with 8mm diameter x 6mm tall magnets…
I'm using Walksnail's GPS, but it should work with any 18mm sized GPS, beware of the cable connector space, of course. It fits tight with mine, so I don't need to double-side tape it or something, but yours might be different. The…
A remix of Itty Bitty Fidget to use 5x1mm magnets meant for tabletop miniatures. You'll need the top part from original design. https://www.printables.com/model/205599-itty-bitty-fidget You'll need to pause the print around 4.2mm up to…
Printed in Bambu PLA Matte - 15% infill - 0.08mm layers with 0.4 nozzle Hardware required: 4x M3 nuts 4x M3 bolts (whatever length required) There is some excess space left after the nut to allow some leeway with the screw length Need to…
This is my version of LilyGo T-Embed Back Shell with power switch. I scraped the switch from some child toy, it looks like SS12D00. The shell uses screws and does not have mounts for magnets. Update 18.02.2026. Added version with 2 holes…
Full description and BOM on my GitHub: https://github.com/olekrause/t-embed-cc1101-plus-GPS-Addon This project adds an ATGM336H module to the LILYGO T-Embed CC1101 Plus Printing suggestions: - Print in PETG - Auto orient the model -…
Nice wall organizer for keys, masks, et cetera. Added embedded magnets with detents on the hooks so that your keys just hang onto the ends. This remix is a fork of the chamfered version by cordilon. I liked his mounting hole addition so I…
Remix of the original “LILYGO T-Embed CC1101 back shell with external antennas” by dansh with 6x3 magnets
This remix is to make it nicer for lidfinity lites to have embedded text cut or popouts, just by removing the lip. To make embedded text for labeling, in your slicer: Create a text object on the flat side. If you are making it a cutout…
Hello, Here's a quick remix of @6d6178 work, allowing to embed 4 magnets into the print. The magnets used are 10x2mm round neodynium magnets. Let me know if you want me to add models for the 221-413 and 221-415 wago. Print at 0.15mm layer…
printed in PETG no support need if use default orientation step file included feel free to use it as you want
My vision of 18650 extension for t-embed. Print with supports. You will need: Battery connectors 7x2 mm round magnets - 4 pcs wire with connector or just cut original battery wire m2 screw 10 mm - 2 pts. But I think you can use that comes…
This is a set of Gridfinity labeled hex bit holders with embedded magnets in the bottom to help align and hold them in place in the grid. I print these with 10% gyroid infill with a 0.4 nozzle and 0.2 layer height. I found a larger nozzle…
The body of a fine tip Sharpie marker is tapered, so this is designed to either be dropped in place (if it's going to be kept in the appropriate orientation) or a gentle friction fit near the cap (if it needs to be mounted in another…
Skadis holder ideal for magnetic items that are difficult to hold in regular holders/mounts like diamond files due to their size. The magnets are to be embedded mid-print so no glue is required at all. There are indents on the front of…
Simple case for t-embed and 18650 extension version Can stuck near usb-c - just push it little bit from usb-c side Print with supports
This dice tower has spots for 9 embedded magnets so you can safely store and transport your dice when not in active use. I designed this to use 4x6mm cylindrical magnets, but I am happy to remix the model to fit other magnet sizes, just…
Adapters for Straight and Angled Talon Magazines. Hot swappable and doesn't need to trim the reinforcing ribs in the magwell. Requires a modified pusher to work with it. Check this collection for more detail. After inserting it, pull the…
This bottle opener is a riff off of the coin-operated bottle opener included with the driver package for the Prusa i3 Mk3 3D printer from Prusa Research. However, I have changed a few things: 1.) The dime is embedded in the print. I did…
The Cyberdyne Systems Skynet logo frame, flattened out for a multi-material printer. Assign a material channel/tool to each part. It's already flipped for printing. Print with PLA or PETG, 0.4mm nozzle, 0.2mm layer height is fine.
This dice tower has spots for 9 embedded magnets so you can safely store and transport your dice when not in active use. I designed this to use 4x6mm cylindrical magnets, but I am happy to remix the model to fit other magnet sizes, just…
![Magnetic Hex Fidget Toy [EMBEDDED MAGNETS 6mm x 2mm]](https://media.printables.com/media/prints/554830/images/4452166_75b3de0b-83e1-4e90-9d3a-5cdbfb1af162/4.jpg)
