158 modeli
My Nextbase 522GW came with two adapters for attaching to the window, a suction cup and a flat plastic base for use with a small piece of 3M VHB. I had only used the suction cup for years and now that I want to permanently attach it with…
Wydruk około 0,21 €–0,26 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This design is intended to use the mounting hardware already on the Pelsee and the BMW mirror mount plate. To access those screws, you need to scrape off the 4 foam pieces on the back of the unit to access the screws. Then you unscrew…
Wydruk około 1,69 €–2,07 € nettoWstępna wycena jednego wariantu
Printed in ASA so it doesn't warp, upright print no supports needed
Wydruk około 0,47 €–0,57 € nettoWstępna wycena jednego wariantu
Zum fixieren des Ladekabels im Auto / For fixing the charging cable in the car
Da meine Halterung für die 70Mai Kamera defekt ist, sie aber dennoch einwandfrei funktioniert, habe ich eine neue Befestigung für die Autoscheibe konstruiert. Benötigtes Material: M3-Schraube - Since my mount for the 70Mai camera is…
This is a GoPro mount for my 2019 Mazda Miata ND GT and also works for my Hyundai Kona. The circular clamp dimensions should fit exactly the rearview mirror with autodimming and homelink. It is angled to avoid the power connector behind…
The rear camera that comes with the RedTiger F7N Dashcam is intended to be mounted on the rear of the car and the bracket that in included is limited to mounting on horizontal surfaces. This bracket will allow you to mount the camera on…
The windscreen centre pod is a good place to attach a dashcam but the covers are quite thin, they aren't flat in the centre and i found creaked annoyingly if a camera was just stuck onto them. This attachment clips around the pod and just…
Certain versions of the VanTrue N4 dashcams do not have the mount for the CPL filters they (and other third parties) sell for these cameras. This model fixes that, allowing for any 37mm lens to be attached to the camera. The adapter is…
This is a replacement part for the Garmin Mini dashcam (1st gen). I have only tested it with PLA. Was plenty strong (printed with 6 perimeters) and fit nicely into the socket of the dashcam. Only problem I could imagine would be the heat…
This is a remix of Pappadakko's redesigned dashcam mount for the 5th-gen 4Runner to work with the U3000 rear camera. I printed it in ABS to help prevent warping from heat in the summer. I recommend installing the camera on the…
Recommended to print out of PETG or other heat tolerant filament. No supports needed. Scale to whatever size you need for your project. Use double sided tape or adhesive on the back.
I bought a 2-channel dashcam for my 4runner and I was left feeling that the methods for mounting the rear camera were wanton. as such, I created this attachment for the rear camera that places it very near the glass and exactly in the…
Mount for Fullscreen Dashcam Mirror for Fiat Ducato 250. Added a Riser for RVs with Front-Plissee printed in ABS with Support and 50% Infill. M4 Screws and Nuts needed Photo shows older smaler Version.
Update 03/26: I added some cable clips in two designs: USB-C and Coaxial. Hey, i designed a perfect mount for the rear cam of a VIOFO A139 / A229 / T130 Dashcam. [Version for A329 Rear Camera on my Profile!] You can slide the cam in and…
Overview This dashcam rear-view mirror mount is designed so that the dashcam never falls down again. Usually, dashcams come with a suction cap mount for the windshield and these like to fall down on warm days, hitting dumps or just after…
Print in PETG, ABS or other filament capable of withstanding car temperatures. Use the original mounting bolt and nut to connect the adapter to the camera (See pictures). I printed mine in PETG with 100% infill and 0.12mm layer height to…
In order to be able to use my dashcam 70mai (model M500) in several vehicles, I have created another compatible holder (to stick, to fix ... ). To attach the holder, I share the bracket from https://www.thingiverse.com/thing:6236453 fully…
This adapter is useful for Yi Dashcams made in the late 2010's under several model numbers, such as my model the “Yi Smart Dash Camera - Model YCS.1015.INT”. I had lost the original mount and since Go Pro mounts are much more supported by…
Support qui se clipse autour du cache du rétroviseur , contre le pare-brise . Il a été développé pour supporter ma Dashcam 70mai M500. J'ai intégré les fixation dans le support. Autre version sans support disponible.
A housing to put the rear view camera on the car roof just behind the sharkfin antenna. Placed here the camera is kept very clean, especially on hatchbacks where the rear of the car gets very dirty very quickly. The full height versions…
BYD Dolphin Surf (EU market) dashcam mount crafted for original BYD camera EL-3776900. Be extra careful when removing the right pillar-A cover. Don't use sharp tools. To access the glove compartment simply open it and push on the sides…
I made a small dashcam rear view camera mount to avoid having to drill through the car body. It uses the screws that come with the original mount for the hinge, and the screws that come with the camera for the backplate. Simply slide the…
A simple clip mount to attach a rear dashcam to a Toyota Tundra (or any other similar truck). This clips in place and stays snug. Use double sided tape and mount your dashcam to it. See photos. Can be clipped into the roof lining on…
3D printed fix for broken slide mount on 70Mai Pro 2018 dashcam. Requires x2 M1.6x10 screw. Print using ABS.
Rearview Mirror GoPro Dashcam Mount remixed for a 2005 Subaru Impreza, should fit any other car with a 19mm mirror mount angled straight back, and either left or right hand drive. Bracket also extends further toward the windscreen than…
So, we've had only had our 20 crosstrek since february and I've had the dashcam I've been going to install since early march, so thought I should get after it. If you have a subie with Eyesight you know that nothing can go in the field of…
Replacement ball socket thing for the garmin mini 2 dash cam. They're like 20 USD on amazon and that's dumb so here's a nominally free one.
Mirror holder for Azdome AR08 and Honda Civic sedan 2008. Fitting to the original ballhead. I propose to print by ASA, or other heat resistant material. PLA or PETG doesn't working well. Melting and warping at summer. Possible to assemble…
Simple mount for a 70Mai dashcam. Printed with 100% infill in ABS to combat the heat-sagging which happened with other mounts.
The mount for my X500 went off to the scrapyard with my car after a crash but the camera was fine. Replacement parts for this old camera are hard to find so I made one myself, based on my memory of the original, and printed it in PETG.…
Because I often travel to countries where using dash cams is strictly prohibited, I needed a smart mounting solution: fast removal and repeatable replacement. I use a Garmin Mini DashCam ( https://www.garmin.com/de-DE/p/621281 ). The…
Dashcam holder for Citroen Berlingo III family (2019+ - also Toyota Proace City, Peugeot Partner, Opel Combo) behind the infotaiment panel. Top part has slot for Navitel R600 dashcam but you can change it for whatever camera you're using.…
English : Support for dashcam 70mai midrive D01 for Renault Clio 3 interior mirror It will take 2 nuts and 2 screws of 3*20mm Français : Support pour dashcam 70mai midrive D01 pour rétroviseur intérieur de Renault Clio 3 Il faudra 2…
This is a clip-on mount for a Vantrue Element E1 dashcam. It should also work with the E1 Pro and E1 Lite. It is designed to clip onto the forward edge of my 2022 Ford Transit 350 XLT van dashboard. I did not want to have the dashcam…
After upgrading to a newer dashcam, I wanted the ability to use my older dashcam (Viofo A119) for rear-view recording, but with a Soft Top, rear-view windshield mounting is impractical. To get the Dashcam to stick to the mount (like you…
Mount a dashcam or electronics in your Toyota vehicle's front windshield using only the stock mirror bracket. No suction cups or drilling required! This mount securely attaches directly to the existing bracket built into windshield. The…
This is simple dashcam holder, which clamps around the rear-view mirror on a Chevrolet Volt (tested on a Gen1 2015 model) and is compatible with the ball-and-socket joint of a Garmin 55 dashcam. The clamp has to be printed with a flexible…
Since I have more than 1 car I designed a new mount to swap the dashcam between cars. Printed at .3 resolution but probably be best at .2 or lower for the mount tab. I printed a test piece in PLA but will use PETG to survive summer car…
I was having trouble attaching the rear dashcam to the trim of my Honda CRV. This is what I came up with. On the rear wing of the wedge I put some ¼ inch adhesive backed foam to help keep the camera in place as well as absorb shock while…
I've installed a 2 channel dashcam into my 2024 Mazda 3 BP. Because I didn't want to stick the rear cam to the headliner or the rear window, I designed the bracket, that slips between the car's roof and headliner. Update : I've reworked…
Cam hold protrusion maybe must be moved. CEL-TEC
We wanted to use our Apeman C550 dashcam in our new car, so I designed this holder for it. I used thick 3M double sided tape to mount it in the car. Dont use PLA: it will deform in the sunlight. ABS works fine. Support is needed! 2025-09:…
Estuche de goma para la dashcam 70mai. Al hacerlo en filamento flexible te aseguras de que no se ralla. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,2 Infill: 80 Filament: Recreus Filaflex…
a motorcycle handlebar mount for a Vsys motorcycle dashcam operation button the ring part should be printed from TPU or other flexibles all other parts should be printed from UV resistant material the Dashcam mount would be published…
We recently got a Garmin dashcam and found that the mounting system was different from other dashcams we've used. This print will adapt the Garmin balljoint mount to universal clamp mounts used on a wide array of dashcam mirror mounts.…
This is a custom 3D-printed alignment shim designed specifically for the Mangoal Ford Maverick 4K Dashcam (Model: MGA 032DBA). Its purpose is to correct the factory camera angle, which can otherwise capture an excessive amount of the…
I didn't want to mount our back dashcam onto the windscreen as I didn't want the cable flexing each time I opened the boot. The clip is wide enough not to move around. It's long enough for your camera to be able to clearly look out of the…
70mai M800 Dashcam mirror holder. Adapter with 15mm ballhead, you can use step file to fit your own clamp. Print with PETG or ABS. Please note the print orientation shown in pics. Need 2 x M3*10mm countersunk head screws and 2 x M3…
It's rear-view mirror mount for GoGEN (CC104) dashcam for my Fiat Ducato. The suction cup was not strong enough.
My friends forgot to remove their mount from the rear windscreen and needed a new one... Rather than paying $15 + shipping I just knocked this out, partially from memory. I've provided two models, one that sorta follows the lines of the…
Allows you to mount a Promate DASHCAM-2 (or potentially a DASHCAM-1) onto a base with a GoPro - type mount. Category: Camera
This is a dashcam mount for a Blackvue DR750S and a Subaru with Eyesight & the headlight high beam assist sensor. This print fits nicely around the headlight sensor and can be affixed with some double sided tape. It was designed to work…
I got a cheap dashcam from China that came with a remote backup camera. In my case, I didn't want to mount on the back bumper, but on the interior of my truck. I designed this simple bracket and mount to do the job. The bracket is matched…
A clip that goes over the top of the Miata RF's wind deflector. One side is angled to match the limits of extension of the Vantrue mount, to allow to upright position “peeking” over the deflector. A hole can be used to ziptie the camera…
Print Settings: Material: PETG - ASA or ABS recommended. Supports: Yes - Build Plate Only Infill: 100% Concentric This is a minimal flag style mount for rear dashcams in vehicles that have movable windows. Such as Toyota trucks and full…
The windshield shadow ‘dots’ made it difficult to use electrostatic stickers to mount a dashcam on the windshield. This backet clips onto the mirror assembly and securely mounts a Vantrue dashcam. Printed on an OPXL5H with Polymaker…
Created these clips to hold the dashcam wire, they are small and hold the wire snug. Used 3m double-sided tape. Printed on Prusa MK3s using Prusament PETG filament at default settings. Please use brim, as the clip is small in size.
70MAI dashcam button blocker This model is a cover for a screen side of your dashcam so no buttons could be used
nextbase dashcam rear view mirror mount mk2
Just like you I bought a dashcam and said, "I'll just use the suction cup until I decide where I really want to mount this thing." Then three years later, just like you, I can't find any of the other mounting accessories, the suction cup…
My rear facing Viofo dashcam was installed off to one side of the rear glass due to having a rear sliding window. I wanted it to face more towards the center so I made this angled mount. I took the existing “flat” mount and measured the…
70mai cover to make the dashcam more invisible in the car.
🚗 Prestigio RoadRunner 585 Dashcam Mount – 3D Printable Replacement This is a 3D printable replacement camera mount designed specifically for the Prestigio RoadRunner 585 Full HD DVR dashcam . The mount provides a secure and stable fit ,…
E N G L I S H Cover for a standard rear dashcam Suitable for those usual ugly things with that sheet metal base. Simply glue it on with polymer adhesive or Pattex-Extreme, then you can remove it again later. G E R M A N Abdeckung für eine…
Skoda Octavia Combi II - Vantrue E2 rear dashcam mount The camera is only clicked in and not glued. It holds very good. Print Settings Printer Brand: Sovol 3D Printer: Sovol SV06 **Rafts:** Yes Supports: No **Resolution:** 0.2 Infill: 20%…
For my work I had to change to a new VW Transporter. The 70-mai dashcam was provided with just 1 static sticker to put on your windscreen. Unfortunately the sticker will work only once so I had no new sticker for my new Transporter.…
I designed this to remove the annoying suction cup of my Aukey DR01 Dashcam Now I can use GoPro Equipment for mounting For my Honda Civic FC 2017 I use the GoPro Barrelclamp + "dashbuchse.stl" out of TPU to mount the dashcam on the pipe…
BACKGROUND: I'm using a Wolffilms Smartphone Dashcam Holder within my car as a smartphone mount. Unfortunately, the small connector piece between the suction cup mount and the smartphone mount broke some days ago so I decided, that this…
Adapter brackets for fitting a Blueskysea DV128 Dashcam to a 2019 Honda CB500X.
This mounting plate matches the original one which comes with the Vlokda S50Pro dashcam. I've included a STEP file, so that you can modify it and add it as a mount to any existing suction cup mount you might want to use. The .3mf version…
Free yourself from the unreliable suction cup mount and mount your front dash cam directly underneath the rear view mirror. Made for the Cobra CDR 840. Mount with M3 hex screws. I tested this mount with both unannealed PLA and PC. The PLA…
Offen gesagt finde ich Drängler lästig wie Sch…haus Fliegen. Mir dauert es einfach zu lange bis diese die Kamera in der Heckscheibe entdecken und auf Abstand gehen. Aufkleber auf Karosserie und Scheibe mag ich genauso wenig, deshalb ein…
Made a Base for my dashcam, because i dont like to install it permanently. Use some double sided tape and stick the camera on to the base! I also added some kind of rubber feet (i reccomend Uhu Patafix [called here in germany]) at the…
Simple mounting plate for the Odrvm dashcam. For the moment printed in PLA, but I'm planning also to replace with ABS or something more resistant to heat. Support are needed. Small pins also need to be removed manually.
This mount allows you to attach a Rexing V5 (or V55 – or any other dashcam that uses the same mount) to a tripod. Rexing cameras have a UVC mode that lets the dashcam act as a webcam, which is neat. Has support for both “small” (¼-20 UNC)…
Note, some users have reported fitment errors between the mount and the ball attachment. I have marked the object as a work in progress and will attempt to identify the source of the errors. For now, slight modification might be required…
I created this case to mount the Insta360 One RS into my car as a dashcam directly powered by cable, without the battery. This way, the battery life does not get affected and The camera feels smaller.
Changed the dimensions of the model to fit my specific dashcam ( https://www.amazon.com/gp/product/B0BJZQ37G7/ref=ox_sc_saved_title_8?smid=A3CIGEUYW4U1DT&psc=1 ) and my car (Toyota Camry SE 2024) Photos in the car are of the mockup I made…
This should fit a 2013–2020 Pathfinder R52 rearview mirror with Homelink. This item replaces part of the cable trim already installed in the pathfinder, allowing a cable with a Ferrite core ring to be covered up. Ferrite core rings are…
you just need a bolt with about 10mm 1/4" thread to screw into the camera. holds the camera so it does not obscure the drivers view. Currently printed in PLA, as it is winter but plan to reprint in ABS-GF, but for now seems to hold nicely
Front camera mount for Viofo A229 Pro and Viofo A329 Pro Dashcam Obviously it has no GPS or power electronics. Just a simple mount for use in rentals for example. Print in a material that doesn't easily warp in a heated car. I used ASA,…
My holder had a smaller Ball, so I changed the ball size zu 13,5mm and 14mm
I have HAD a Cobra dash cam (Model CDR855BT) that came with a suction-cup mount to be used on the windshield glass. It would sometimes stay attached for up to a few weeks at a time but then I'd find the camera in the seat or the floor…
********** ENGLISH *********** Mounts and extensions for the cameras of the usual motorcycle dashccams. The new version has the following improvements: Base arms detached from support plates, so now the "eyes" are printed from "loops" and…
Dashcam Platform Adapter for Tesla Model 3 Rearview Mirror This adapter provides a flat platform to mount/secure the camera to the Tesla Model 3's rear view mirror base. (I use 3M VHB tape to attach it to the base.) Note: using PETG or…
The intention is to suspend a dash cam from the car's roof liner instead of VHB'ing it to the windshield. Material testing in progress: Black ASA on the original 3mm platform has failed on a moderately warm april day. Currently…
I have a Thinkware u3000 that won't stay running so I purchased a Focuway T5-Pro to replace it and made this adapter to avoid sticking something else on the window but the Focuway is apparently DOA so it is being returned, sigh. However,…
This is a dashcam connector I made to connect a dashcam to the rearview mirror/screen of a Nissan Leaf 2024. There are two parts: A brace for the dascam itself - it connects to the existing screwholes of the dashcam with longer screws. A…
What it is Adapter to reuse an existing 15mm dashcam ball-joint windshield mount and attach a DJI Action 4 using the Tripod Mount Adapter . Compatibility 15mm ball joint (measure your ball diameter to confirm) DJI Tripod Mount Adapter…
Got tired of the cam constantly falling down as no sticky tape/pad would stick to the plastic cover on the boot lid “roof”. I've looked everywhere for stls that fit my camera type and found the model I based this off although the camera…
A mount to adapt your HP f210 dashcam to position it in the rear window of a ute/pick-up truck or van. Requires modification to the mount that comes with your dashcam. I have printed the parts in PETG and they have survived a summer in…
This is a collar that fits behind the suction cup of the Halfords HDC200 dashcam. Over time the cup will lose suction power, so I designed this thin collar (1.2mm in thickness) to go behind it, so it will raise the borders creating a bit…
I created this adapter to use a second 70Mai Dashcam for rear video on the Mini Cooper from my son. This will fit any model with a pipe diameter of 14mm and a distance (middle-to-middle) of 110mm. It is designed to be mounted on left side…
Succion cup holder part for dashcam. Use others parts from original dashcam holder to make full assembly. The original holder is too bent or to use if the original part is broken. You can adapt to many others designs.
this is the model of the dash camera i made the support for! https://www.aliexpress.com/item/1005008122563945.html?spm=a2g0o.order_list.order_list_main.90.1f581802nifd4g i lost mine so i desgined this so i can mount it again to the glass…
Hey, i upgraded my Dashcam to a VIOFO A329 and now the original design doesnt fit anymore. So i re-designed the clip with a mount for the new rear cam. Use the Mount file from the original design. Now you can screw the Dashcam directly to…
Our van doesn't have a rear view mirror but had a nice holder already mounted on the windscreen. Since vacuum mounts tend to fall off and gluing a holder isn't my thing, I designed a simple mount that snaps into place. You need to take…
![Kabelclip fürs Auto / Cable clip for car DASHCAM and SMARTPHONE [PETG and TPU Version]](https://media.printables.com/media/prints/552878/images/5759815_245953e8-271d-45d0-a252-8548549ca984_155cb0e4-9909-4e34-804f-34ab8d0ed35b/bearbeitet-1.jpg)
![[WIP] Dashcam roofliner suspension](https://media.printables.com/media/prints/799926/images/6487220_33064957-adc3-4a9a-989c-7d185d88ab0d_884c83b0-4d92-4e72-8ab9-0f07e11b1e25/img_2457.jpg)
